Detecting the Onset and Progression of Spinodal Decomposition using Transient Grating Spectroscopy
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: We're looking at the paper: "Detecting the Onset and Progression of Spinodal Decomposition using Transient Grating Spectroscopy".
Mira: Here's the gist of the paper. Spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS) The key mechanistic insight is the non-linearity in elastic moduli as function of Cr content renders a spinodally decomposed Fe-Cr alloy stiffer than an equivalent solid solution for a certain range of initial chromium compositions.
Kai: Detection Methodology The study demonstrates that TGS can be used as a practical tool for nondestructive evaluation of key materials susceptible to such degradation.
Mira: The technique involves using two pump lasers crossed at the sample surface to generate a spatially dependent intensity pattern which establishes a corresponding spatial temperature profile, launching two counter-propagating surface acoustic waves along the sample surface.
Kai: TGS can be used as an ex-situ or in-situ method.
Paper summary: Kai: To wrap up the paper "Detecting the Onset and Progression of Spinodal Decomposition using Transient Grating Spectroscopy", they show that you can measure the stiffening effect of spinodal decomposition in iron thirty-six chromium by both in-situ and ex-situ TGS.
Mira: They back this up with differential scanning calorimetry showing unmixing enthalpy of twenty-seven point three plus nine point five joules per gram and a peak temperature around five hundred fifty degrees Celsius for the iron thirty-six chromium alloy aged for ten hours.
Lev: The hybrid molecular dynamics and Monte Carlo simulations matched these experimental measurements on the extent of iron thirty-six chromium stiffening caused by spinodal decomposition, showing an increase in C one one, C one two, and C four four by five point seven plus or minus zero point zero seven percent, three point zero three plus or minus zero point zero nine percent, and four point three two plus or minus zero point zero four percent.
Kai: TGS is shown to be sufficiently sensitive to measure SAW speed changes in the iron thirty-six chromium alloy under the time at temperature aging conditions used in this study.
Mira: The conclusion is that TGS is a relatively inexpensive and non-destructive technique capable of accurately tracking elastic properties both in and ex-situ.
Lev: It has the potential for in-service monitoring of structural components, provided you account for those kinetic changes we discussed earlier.
Conclusion: Kai: So, this paper is about detecting spinodal decomposition in iron thirty-six chromium using transient grating spectroscopy.
Mira: Right, it shows that you can measure how materials get stiffer when they decompose into different phases, and this technique works both inside and outside the material.
Lev: From a real hardware standpoint, if we're talking about measuring those elastic constants with TGS at these temperatures, we need to make sure the setup is stable enough to track those subtle changes in the sound wave speed.
Kai: Exactly. The authors found that their method was sensitive enough to see stiffening in the iron thirty-six chromium alloy under aging conditions they used for a decent amount of time.
Mira: And they showed that differential scanning calorimetry confirmed this with an unmixing enthalpy measurement around twenty seven point three joules per gram and a peak temperature near five hundred fifty degrees Celsius.
Lev: That enthalpy release tells us something about the thermodynamics, but we need to look at the actual mechanical change for us to see how it translates into real stress on hardware.
Kai: The simulation work supports this, showing that molecular dynamics and Monte Carlo models match the experimental results pretty well regarding those stiffness increases in C one one, C one two, and C four four.
Mira: It’s interesting because it connects the microscopic phase separation seen by calorimetry to a macroscopic change you can measure with spectroscopy.
Lev: For us building error correction systems, knowing how these material properties drift over time is crucial because those drifts directly affect the noise we have to correct for in a real device.
Kai: So, the main point here is that TGS is a relatively cheap and non-destructive way to track these elastic property changes in iron thirty-six chromium.
Mira: It opens up the possibility of monitoring structural components during their service life if they are subject to these kinds of thermal aging effects.
Lev: We need to figure out how robust this measurement is when you take it off the pristine lab bench and put it on a vibrating, stressed component in a real environment.
Maxwell Raea, Merrill Chianga, Mahmudul Islama, Angus P. C. Wylieb, Avery Nguyenb, Myles Stapelbergb, Saleem A. Al Dajanic, Kristýna Repčekd, Tomáš Grabecd, Abby Kaplana, Rodrigo Freitasa, Michael P. Shortba
Department of Materials Science and Engineering, Massachusetts Institute of Technology. · Department of Nuclear Science and Engineering, Massachusetts Institute of Technology. · Department of Civil and Environmental Engineering, Massachusetts Institute of Technology. · The Institute of Thermomechanics of the Czech Academy of Sciences
cond-mat.mtrl-sci
Submitted: 2026-01-10
Updated: 2026-11-08
Journal ref: npj Materials Degradation (2026)
DOI: 10.1038/s41529-026-00909-2
Code: https://github.com/shortlab/2025-mraechuspinodal-is-real
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 85/100
The gist: Spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS) The key mechanistic insight is the non-linearity in…
Key concepts
- Spinodal Decomposition
- This is a process where a uniform material spontaneously separates into two distinct phases because the system is thermodynamically unstable. In Fe-Cr alloys, this leads to structural changes that alter the material's mechanical properties, specifically making it stiffer.
- Transient Grating Spectroscopy (TGS)
- TGS is a non-destructive technique used to probe materials. It works by using two pump lasers to create a surface intensity pattern that generates counter-propagating surface acoustic waves (SAWs). Changes in the SAW speed reveal information about the material's elastic properties, allowing researchers to monitor phase changes in real time.
- Modulus Stiffening
- This refers to an increase in a material's stiffness or elasticity. In this context, spinodal decomposition causes a measurable stiffening effect in the Fe-Cr alloy. This stiffening is the key observable that allows researchers to confirm the presence and progression of phase separation during thermal aging experiments.
Terminology
Summary
Spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS) The key mechanistic insight is the non-linearity in elastic moduli as function of Cr content renders a spinodally decomposed Fe-Cr alloy stiffer than an equivalent solid solution for a certain range of initial chromium compositions. p. 0 We demonstrate that spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS). The key mechanistic insight is the non-linearity in elastic moduli as function of Cr content
renders a spinodally decomposed Fe-Cr alloy stiffer than an equivalent solid solution for a
certain range of initial chromium compositions. We demonstrate that spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS). The key mechanistic insight is the non-linearity in elastic moduli as function of Cr content
renders a spinodally decomposed Fe-Cr alloy stiffer than an equivalent solid solution for a
certain range of initial chromium compositions.Where the paper says it
Where the paper says it
Detection Methodology
The study demonstrates that TGS can be used as a practical tool for nondestructive evaluation of key materials susceptible to such degradation. The technique involves using two pump lasers crossed at the sample surface to generate a spatially dependent intensity pattern which establishes a corresponding spatial temperature profile, launching two counter-propagating surface acoustic waves along the sample surface. p. 1 TGS is a laser-based spectroscopic technique in which two pump lasers are crossed at
the sample surface to generate a spatially dependent intensity pattern on the surface of a
reflective material. This intensity profile establishes a corresponding spatial temperature
profile, which launches two counter-propagating surface acoustic waves along the sample
surface. 3
elastic stiffness tensor, both of which can vary with temperature and other intensive variables
[16]. TGS can be used as an ex-situ or in-situ method. 18, with in-situ heating under < 1 × 10−5 Torr vacuum using a
HeatWave button heater (catalog number #101275-28) and continuously monitored
temperature via either an in-heater or on-sample K-type thermocouple. In the two in-situ experiments, two different temperature control methods were used.Where the paper says it
Where the paper says it
Where the paper says it
Evidence of Phase Separation
The presence of spinodal decomposition in the Fe-36Cr alloy is substantiated by differential scanning calorimetry (DSC). Two key features of the heat flow vs. p. 5 Next, since
separation of phases formed during aging will only occur in the first heating step, the
subsequent heats (two through five) are averaged across the two measured samples, to provide
an “as-unmixed” value. Finally, the average of the first heating steps is taken, and the
subsequent heating steps are subtracted, yielding a curve representing only the heat flow unique
to the first heat. The region of interest for the phase transformation is 500°C - 625°C, based on the
aging temperature, peak width, and heating rate combinations reported in other studies of
unmixing [21,22]. The polynomial baseline is then subtracted from the DSC data. 999% argon cover gas with < 1 ppm oxygen impurities
using a zirconium getter ring. For the validation test, two samples of Fe-36Cr aged at 500°C
for 10 hours were measured. The
authors hypothesized that spinodal decomposition stiffened the -ferrite phase, causing the
speed of a subset of the measured elastic waves to increase into the elastodynamically
unallowed region [14]. In addition to producing waves in the unallowed region, aged samples
also showed a higher incidence of “peak splits”, where two acoustic modes are supported in
the same measurement. performed aging experiments at 500°C across a range of chromium concentrations to identify
the chromium composition where the phase transition mechanism changes from nucleation and
growth to spinodal decomposition [8–10]. Small-angle neutron scattering (SANS) has also
been used to study iron-chromium phase separation [7,11].Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Mechanical Property Changes
The ex-situ TGS rotation study further controls for the influence of crystal orientation on SAW speed, enabling direct measurement of the effect of thermal aging on the angular SAW dispersion. The angular dispersion of SAW velocities in the Fe-36Cr and Fe-26Cr alloys is shown in Fig. p. 7 4) for the Fe-26Cr alloy. The angular
dispersion of SAW velocities in the Fe-36Cr and Fe-26Cr alloys is shown in Fig. The angular
dispersion of SAW velocities in the Fe-36Cr and Fe-26Cr alloys is shown in Fig. 4 for the
conditions shown in Table 2. 4 shows the angular SAW dispersion for the Fe-36Cr alloy
for the different heat treatment conditions tested. Using the experimentally measured angular
SAW dispersions, the inverse problem was solved to compute the two independent elastic
constants that produce significant out-of-plane displacement.Where the paper says it
Where the paper says it
Where the paper says it
Simulation and Correlation
Hybrid MD/MC simulations were performed to support the experimental analysis. The elastic stiffness tensor for the Fe-36Cr alloy in the aged condition shows an increase in C11, C12, and C44 by 5. p. 7 Later, these
results will be discussed in the context of spinodal decomposition in elastically anisotropic
media. Figure 3 shows the time-temperature history of Fe-36Cr and Fe-26Cr aging, along with
the relative minimum SAW speed for the Fe-36Cr alloy as a function of heat treatment
condition. Later, these
results will be discussed in the context of spinodal decomposition in elastically anisotropic
media. Figure 3 shows the time-temperature history of Fe-36Cr and Fe-26Cr aging, along with
the relative minimum SAW speed for the Fe-36Cr alloy as a function of heat treatment
condition. 1°C in air for 2 hours, followed by
a drop quench in DI water. Subsequent heat treatment procedures were performed at
500±0. showed, via molecular dynamics simulations, that
iron-chromium de-mixing—analogous to spinodal decomposition—stiffens the elastic
modulus of iron-chromium alloys [14]. The same study also predicted surface acoustic wave
(SAW) and pseudo surface acoustic wave (PSAW) speeds in duplex CASS alloys, and
subsequently measured SAW and PSAW speeds in samples without spinodal decomposition
in the -ferrite phase.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Kinetic Insights
In-situ TGS revealed clear stiffening in both alloys as a function of time at temperatures where spinodal decomposition occurs. The rate of stiffening decreases significantly after ~1 hour for the in-heater TC control, suggesting a shift in the kinetics of spinodal decomposition. This kinetic change is consistent with in-situ SANS data on spinodal progression in Fe-Cr alloys. p. 7 From left to right: Fe-36Cr alloy after etching to reveal grain structure (optical image),
after razor marking and re-polishing (SEM image), and an electron backscatter diffraction
pattern. 2 TGS Ex-situ Analysis
TGS results on the Fe-36Cr and Fe-26Cr alloys will be presented first, followed by
calculation of the change in the elastic constants of the Fe-36Cr alloy as a function of heat
treatment condition. 4 Elastic Constant Calculation from Ex-Situ TGS Data
A subset of the independent elastic constants can be calculated by solving the so-called
“inverse problem” using the SAW speed as a function of rotation angle [16]. To solve the
inverse problem and compute changes in elastic constants, the sample must be a single grain
with dimensions larger than the spot size of the TGS probe laser (~62 m across) and a known
surface orientation.Where the paper says it
Where the paper says it
Conclusion
The results presented demonstrate the stiffening effect of spinodal decomposition in Fe-36Cr is measurable by both in-situ and ex-situ TGS. DSC provides evidence of spinodal decomposition in the Fe-36Cr alloy, and hybrid MD/MC results show agreement with experimental measurements on the extent of Fe-36Cr stiffening caused by spinodal decomposition. p. 0 We confirm the presence of spinodal
decomposition in the 36 at. % chromium alloy using differential scanning calorimetry (DSC),
linked to known spinodal decomposition energetics, and show via atomistic simulations that
elastic modulus stiffening is expected after spinodal decomposition in the 36 at. The work of Al Dajani et al. used TGS on CASS alloys to measure changes in elastic
wave speed as a function of time at temperatures where spinodal decomposition is known to
occur (10,000-30,000 hours at 290-400°C) [14]. More recent
literature has proposed transient grating spectroscopy (TGS) as a method for in-situ and ex-situ
measurement of spinodal decomposition via elastic wave speed measurements [14]. TGS is a laser-based spectroscopic technique in which two pump lasers are crossed at
the sample surface to generate a spatially dependent intensity pattern on the surface of a
reflective material. The ability to quickly, conclusively, and non-destructively detect the onset of spinodal
decomposition before catastrophic materials degradation would represent a significant advance
in materials testing. We demonstrate that spinodal decomposition can be detected in binary FeCr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS). The code used to perform
this matrix algebra can be found in the data availability GitHub repository for this paper [17]. 3 Transient Grating Spectroscopy
Two TGS instruments were used, one for ex-situ measurements at room temperature (in
between heat treatments), and one for separate in-situ experiments.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
REFERENCES
[1] B. Robert W., A. Samuel M., C. Craig W., 17.3 Classification of Phase Transformations: Continuous Versus Discontinuous Transformations, in: Kinetics of Materials, John Wiley & Sons, Inc. p. 0 Spinodal phase
transformations are initially small in degree, but large in extent—in direct contrast to nucleation
and growth phase transformations, which are initially large in degree but small in extent [1]. Spinodal decomposition can have drastic effects on engineering materials.Where the paper says it
[2] T.S. Byun, Y. Yang, N.R. Overman, J.T. Busby, Thermal Aging Phenomena in Cast Duplex Stainless Steels, JOM 68 (2016) 507–516 https://doi. p. 0 Spinodal decomposition can have drastic effects on engineering materials. In duplex cast
austenitic stainless steel (CASS) alloys, the ductile-to-brittle transition temperature (DBTT) of
an in-service component operated at 400°C can shift to room temperature within two monthsWhere the paper says it
[3] G. Obulan Subramanian, B.S. Kong, H.J. Lee, C. Jang, Evaluation of the thermal aging of δ-ferrite in austenitic stainless steel welds by electrochemical analysis, Sci Rep 8 (2018) 15091 https://doi. p. 0 Spinodal decomposition can have drastic effects on engineering materials. In duplex cast
austenitic stainless steel (CASS) alloys, the ductile-to-brittle transition temperature (DBTT) of
an in-service component operated at 400°C can shift to room temperature within two monthsWhere the paper says it
[4] J.E. Westraadt, E.J. Olivier, J.H. Neethling, P. Hedström, J. Odqvist, X. Xu, A., Steuwer, A high-resolution analytical scanning transmission electron microscopy study of the early stages of spinodal decomposition in binary Fe–Cr
[5] J. Zhou, J. Odqvist, M. Thuvander, P. Hedström, Quantitative Evaluation of Spinodal Decomposition in Fe-Cr by Atom Probe Tomography and Radial Distribution Function Analysis, Microsc Microanal 19 (2013) 665–675 https://doi. p. 1 Embrittlement via spinodal decomposition
in the -ferrite phase of duplex stainless steels is a well-known life-limiting phenomenon, and
literature contains extensive experimental evidence for spinodal decomposition across a range
of iron-chromium compositions for temperatures at or below 500°C. Spinodal decomposition can be characterized at the nanoscale using atom probe
tomography (APT) or scanning transmission electron microscopy (STEM) to see small
composition fluctuations associated with phase separation [4–7].Where the paper says it
[8] W. Xiong, P. Hedström, M. Selleby, J. Odqvist, M., Thuvander, Q., Chen, An improved thermodynamic modeling of the Fe–Cr system down to zero kelvin coupled with key experiments
[9] W. Xiong, M. Selleby, Q. Chen, J. Odqvist, Y., Du, Phase Equilibria and Thermodynamic Properties in the Fe-Cr System, Critical Reviews in Solid State and Materials Sciences 35 (2010) 125–152 https://doi. p. 0 Introduction
Spinodal decomposition is a continuous phase transformation that can embrittle
materials and limit the service lifetime of critical engineering components. During spinodal, a
solid solution decomposes into two phases via composition fluctuations that lower the free
energy of the system.Where the paper says it
Hybrid MD/MC simulations were performed to support the experimental analysis. The elastic stiffness tensor for the Fe-36Cr alloy in the aged condition shows an increase in C11, C12, and C44 by 5.74±0.07%, 3.03±0.09%, and 4.32±0.04% on a percentage basis <ref:2601. p. 2 , G-phase precipitation), because CASS alloys are complex
engineering materials with multiple alloying elements and a complex microstructure [14]. In
addition, reproducing the peak-split assessment from the open data repository of ref 14 is
challenging because noise in the power spectrum of the TGS trace is difficult distinguish from
peaks due to acoustic modes.Where the paper says it
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved AI can perform non-destructive evaluation of materials by utilizing transient grating spectroscopy to detect spinodal decomposition in binary FeCr alloys via elastic wave speed measurements.
-
The improved system can quantify spinodal decomposition kinetics in situ by tracking the change in elastic wave speed over time at temperatures where spinodal decomposition occurs, as demonstrated by the observation that
SAW speed stiffened in both samples during heat treatment at 475 degrees C and 500 degrees C.
-
The AI system can correlate nanoscale phase separation with macroscopic mechanical property changes by integrating data from transient grating spectroscopy with differential scanning calorimetry to measure
unmixing enthalpy of 27.3 +/- 9.5 J/g
as a verification of spinodal decomposition in Fe-36Cr alloy. -
The improved system can predict the magnitude of elastic modulus stiffening using hybrid molecular dynamics simulations, showing that
the relative change in C' from random solid solution to the thermally equilibrated state at 500 degrees C is 9.1 +/- 0.3%.
-
The AI system can distinguish between different kinetic regimes of spinodal decomposition by analyzing the slope changes in SAW speed during in-situ tests, identifying that
the rate of stiffening after ~1 hour appears to approach zero
for the in-heater temperature control case.
Abstract
Spinodal decomposition can degrade corrosion resistance and embrittle materials. The ability to quickly, conclusively, and non-destructively detect the onset of spinodal decomposition before catastrophic materials degradation would represent a significant advance in materials testing. We demonstrate that spinodal decomposition can be detected in binary Fe-Cr alloys via modulus stiffening using in situ and ex situ transient grating spectroscopy (TGS). The key mechanistic insight is the non-linearity in elastic moduli as function of Cr content renders a spinodally decomposed Fe-Cr alloy stiffer than an equivalent solid solution for a certain range of initial chromium compositions. We confirm the presence of spinodal decomposition in the 36 at.% chromium alloy using differential scanning calorimetry (DSC), linked to known spinodal decomposition energetics, and show via atomistic simulations that elastic modulus stiffening is expected after spinodal decomposition in the 36 at.% chromium alloy. The results of this study suggest the potential use of TGS as a practical tool for non-destructive evaluation of key materials susceptible to such degradation.
Related papers
- Structural contribution to light-induced gap suppression in Ta 2 NiSe 5
- Anatomy of fast current-induced skyrmion motion in synthetic antiferromagnets
- Magnetic control of an exciton-polariton condensate in a van der Waals magnet
- High-pressure elastic properties of GeO2 polymorphs up to 120 GPa
- Decoupling Strain-Rate Sensitivity and Deformation Length Scale Effects in Neutron-Irradiated Tungsten: A Coupled Nano-Indentation, HR-EBSD and Crystal Plasticity Study
- Magnetism modulation in Co3Sn2S2 by current-assisted domain wall motion