Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions

arXiv:2512.05455 · cond-mat.mtrl-sci · Submitted 2025-12-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions".

Mira: Here's the gist of the paper. Understanding the crystallization pathways of water-rich ammonia-water (NH3-H2O) solutions and the stability of ammonia hydrates is key to unraveling the behavior of complex hydrogenbonding networks as well as for planetary interior modelling.

Kai: Here, we investigate the effect of compression rates on the crystallization pathways of 25 wt% NH3 aqueous solutions at room temperature using dynamically compressed diamond anvil cells (dDAC) coupled with time-resolved X-ray diffraction.

Mira: We show that compression rates exceeding 0.5 GPa/sec promote direct crystallization of a body-centered cubic (bcc) phase (DMA’) with possible AMH stoichiometry coexisting with H2O ice VII, while rates below 0.2 GPa/sec stabilize monoclinic NH3-rich AHH-II and ice VII phases.

Kai: Intermediate rates between 0.2-0.5 GPa/sec produce a mixture of both hydrates alongside ice VII, hence demonstrating the role of compression rate on the crystallization sequence of ammonia solutions.

Title and authors: Kai: So we're looking at this paper called "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions" and it’s by Mondal, Mohrbach, Glazyrin, Liermann and Sanchez-Valle. It sounds like they’re tackling those nagging inconsistencies in the crystallization sequence that scientists have seen reported when they push these mixtures to high pressure.

Mira: Yeah it is interesting because understanding how water and ammonia bond under extreme conditions is crucial for figuring out what materials might be inside icy moons or distant exoplanets. This paper seems to focus on how fast you compress the solution actually dictates which crystal structure forms.

Lev: I'm curious about the setup they used. They’re using dynamically compressed diamond anvil cells, or dDACs, with time-resolved X-ray diffraction to see what happens in real time during compression runs of twenty-five weight percent ammonia aqueous solutions at room temperature <ref:2512.05455#pg1,using dynamically compressed diamond anvil cells>.

Kai: Exactly. They are looking at the crystallization pathways and how those pathways change based on the rate of compression applied. The core result they show is that this rate dependence is pretty significant, and it changes the final phase assembly you get.

Mira: And what they find depends heavily on that compression rate, which is a really important detail because it suggests that kinetic effects matter just as much as the final pressure and temperature conditions when these systems are forming.

Lev: The summary mentions three distinct phase assemblages depending on whether the compression rate is above or below zero point two GigaPascals per second <ref:2512.05455#pg1>. That gives us a clear roadmap for what we expect to see experimentally.

Kai: Right, so they found that if you compress faster than zero point five GigaPascals per second, you get a direct crystallization of a body-centered cubic phase, called DMA prime, which can coexist with ice VII.

Mira: And below zero point two GigaPascals per second, the system tends to stabilize the monoclinic ammonia rich AHH two phase along with ice VII <ref:2512.05455#pg1>. That seems like a pretty clear split based on how aggressively you squeeze it.

Lev: Then they also found that in between those two rates, between zero point two and zero point five GigaPascals per second, you get a mix of both the AHH two and the DMA prime phase alongside ice VII. That intermediate range shows how sensitive the whole process is to that specific rate.

Title and authors: Kai: It’s like they are showing that you can’t just look at static pressure and temperature; the speed at which you apply that pressure really dictates what happens structurally.

Mira: And looking further, they checked the stability of these phase assemblages up to ninety-three GigaPascals for the AHH two plus ice VII mix and up to one hundred forty-six GigaPascals for the DMA prime plus ice VII mix <ref:2512.05455#pg3>.

Lev: They also found that the bcc structure of that DMA prime phase is stable all the way up to one hundred forty-six GigaPascals without any evidence of phase transformations happening within that range, which is good data for modeling <ref:2512.05455#pg3>.

Kai: They also did some stoichiometry estimation on this DMA prime phase by comparing its pressure volume data against known phases like ammonia monohydrate diamond imitation, or AMH-DIMA.

Mira: And they found that the good agreement between the compression curve of the DMA prime phase and that of AMH-DIMA suggests a one ammonia to one water ratio for that DMA prime phase, which is pretty telling.

Lev: They also used a single equation of state fit to describe both phases, and they noted that the bulk modulus value for the DMA prime phase is higher than for the AHH two plus ice VII phase, but it’s still close to what you would expect for an AMH-DIMA phase.

Kai: And there’s this point about impurities; they noticed that when ice VII coexists with the DMA prime phase, it seems to alter how you observe the compression behavior of the water ice itself.

Mira: They suggested this deviation could be explained by ammonia impurities actually getting incorporated into the structure of that bcc H2O ice VII lattice. That’s a big idea because it links chemical species directly into the crystal structure at high pressure.

Lev: It also mentioned something about how volume changes based on things like large cations like calcium and sodium inducing lattice compression, or how methane alcohol incorporation leads to an expansion of the ice VII lattice, which is important for modeling real-world mixtures.

Kai: So, looking at these results together from this paper on "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions," it seems like they’ve really resolved those discrepancies in the crystallization sequence by showing how compression rates are a key driver.

Title and authors: Mira: It gives us a better handle on the kinetics of phase formation in these hydrogen bonded systems, which is vital for anyone modeling planetary interiors where these compounds might be present under immense pressure.

Lev: And for someone building real hardware, seeing that the bcc DMA prime phase is stable up to one hundred forty-six GigaPascals gives us a hard limit on what those materials can withstand structurally <ref:2512.05455#pg3>.

Kai: So, as we wrap up this discussion on this paper, the main implication is that we need to consider compression rates when predicting the stability and form of these ammonia hydrates in extreme conditions.

Mira: Exactly. This paper shows that the crystallization pathway isn't just a function of pressure and temperature; it’s also dependent on how quickly you push things together, which has real consequences for phase diagrams.

Lev: I just want to add that from an engineering standpoint, the fact that they can predict these phase boundaries using dDAC runs is valuable because it validates the experimental method for probing these high pressure regions.

Kai: So to sum up this paper on "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions," we see that compression rate dictates whether you get the monoclinic AHH two, the bcc DMA prime, or a mixture of both with ice VII.

Mira: It really solidifies the picture that kinetic control is essential here, and it points towards incorporating ammonia into the ice VII lattice at high pressures.

Lev: And for future work, I’d say they need to focus more on those structural identity questions about the DMA prime phase itself, since they infer it’s stable but haven't fully characterized its atomic arrangement.

Kai: It sounds like a solid piece of work that clarifies a lot of confusion in the literature about these complex hydrogen bonding networks.

Mira: It definitely provides a clearer picture for anyone trying to model the phase behavior of icy bodies, which is where this stuff really has its biggest payoff in terms of science.

Lev: I think we’ve covered the main points on how compression rate shifts those three phase assemblages and the stability limits they found up to one hundred forty-six GigaPascals <ref:2512.05455#pg3>.

Kai: That’s it for this paper, "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions." We’ll be looking at the next paper soon.

The paper's summary: Kai: So, to recap, this study looked at how fast you compress ammonia water solutions and found that the crystallization process changes depending on whether you push it hard or slow, which really impacts what phases actually form inside.

Mira: Exactly. It’s not just about the final pressure; the speed of compression is a major factor in determining if you get one crystal structure or a mixture of structures.

Lev: And looking at the results, they found three clear scenarios based on that compression rate. Below zero point two gigaPascals per second, you get this monoclinic ammonia rich phase alongside water ice VII.

Kai: Above zero point five gigaPascals per second, the system favors a direct crystallization of a body-centered cubic phase, which they call DMA prime, coexisting with that same water ice VII.

Mira: And in between those two rates—say from zero point two to zero point five gigaPascals per second—you get a mixture of both those phases alongside the water ice VII. It really shows how kinetic control dictates the pathway here.

Lev: They also checked the stability limits for these mixtures up to ninety-three gigaPascals for that first assembly and one hundred forty-six gigaPascals for the DMA prime plus water ice VII group. The bcc structure of DMA prime stayed stable right up to one hundred forty-six gigaPascals without any phase changes happening in that range.

Kai: That stability limit is pretty high, which is important for us when we think about materials under extreme conditions like those in planetary interiors or icy moons.

Mira: And they did some stoichiometry work on that DMA prime phase by comparing its pressure volume data to something called AMH-DIMA. They found a good agreement, which suggests a one ammonia to one water ratio for that DMA prime structure.

Lev: That's a solid piece of evidence suggesting the chemical composition is fixed in that specific crystal structure at high pressure.

Kai: But there’s also this interesting point about impurities; they observed that when the DMA prime phase and water ice VII are together, it seems to change how you measure the water ice behavior itself.

Mira: They hypothesize that this deviation could come from ammonia impurities actually getting incorporated into the structure of that bcc water ice lattice. That’s a pretty deep implication for how we model these high-pressure ices.

Lev: And they also talked about how things like large cations, such as calcium and sodium, can cause volume reduction in the lattice, or how methane alcohol incorporation can actually lead to an expansion of the water ice lattice itself. That’s a bit more complex than just simple mixing.

Kai: So what this means for us is that when we predict phase behavior for these ammonia water mixtures, we really have to account for that compression rate because it dictates which chemical pathway you follow.

Mira: It solidifies the idea that kinetic effects are essential here, and it points toward a more intricate chemistry where ammonia isn't just sitting around; it’s actively participating in the crystal structure of ice VII at high pressure.

Lev: For building real hardware, seeing those stability limits up to one hundred forty-six gigaPascals gives us a hard structural boundary to work within for any material we design under those conditions.

Kai: So basically, this paper resolves some of the confusion in the literature about how these ammonia hydrates crystallize by showing that compression speed is a key driver determining the final phase assembly.

Mira: It gives us a clearer picture for anyone trying to model phase behavior for icy bodies, which is where this stuff really has its biggest payoff in terms of science.

Lev: I think we should keep looking at those structural identity questions about that DMA prime phase itself, since they inferred it's stable but didn't fully characterize the atomic arrangement yet.

The paper's improvements: Tom: So we're looking at how these authors suggest improving their own work on ammonia hydrate crystallization under compression rates, and they’re focused on refining those structural predictions and chemical models.

Kai: They suggest a few ways to make the analysis stronger, starting with better modeling of the impurities that are present in the solution.

Mira: Yeah, they're pointing out that when you look at how ammonia gets incorporated into that water ice lattice, it needs a more detailed approach to capture those structural effects accurately.

Lev: They mention modeling how things like large cations, such as calcium and sodium ions, induce volume reduction in the lattice versus how something like methane alcohol incorporation might cause an expansion of the water ice structure. That adds another layer to the chemical physics we need to consider.

Kai: So they’re moving beyond just looking at the bulk volume changes and trying to model those specific atomic interactions that happen when you have a mixture of species under pressure.

Mira: Exactly, it’s about making sure the equations of state fit those real-world deviations, not just the idealized pure phases they started with. They suggest using a third order Birch-Murnaghan equation of state fit for both the ammonia rich and the bcc phase.

Lev: That's practical because it gives you a more robust way to compare their calculated bulk modulus values against what we see in other literature, like the AMH-DIMA phase. It’s a better way to check if their structural identity claims hold up when you look at the physics of the pressure-volume data.

Kai: And they want to tie this back into how we actually build these systems, by showing how those equation of state parameters compare with established data. It connects the theory right back to what we see in experimental results.

Mira: Plus, they’re trying to get better at predicting the stoichiometry of those new phases, like that bcc DMA prime phase, by using that comparison between its compression curve and the AMH-DIMA curve. That’s a solid way to estimate the ratio without needing direct measurements on every single point.

Lev: For real hardware design, being able to use those refined equation of state parameters means you can predict how that material will behave under stress even if you haven't built that exact pressure condition yet. It reduces the guesswork for running simulations.

Kai: And they’re also trying to make sure the models are as accurate as possible by incorporating things like recurrent neural networks to embed stochastic dynamics, which is a way to handle the complex diffusion and drift of those systems at high pressure.

Mira: So they’re basically saying that moving forward, we need more sophisticated ways to model these complex hydrogen bonding networks, not just static phase diagrams. It's about capturing the dynamic interplay between the ions and the water molecules as you compress them.

Lev: Right, it moves us from just observing phases to actually predicting their stability and behavior under various operational conditions using more detailed physics in our simulations.

Conclusion: Kai: So we're wrapping up this look at "Compressional rate-dependent stability of ammonia hydrates crystallized from water-rich ammonia-water solutions." The main point is that compression speed really dictates which crystal structure you end up with in these ammonia water mixtures.

Mira: It’s pretty clear that kinetic control is the main driver here, showing how fast you squeeze the system matters for whether you get the monoclinic phase, a bcc phase, or a mix of both.

Lev: I just want to stress that seeing those stability limits up to one hundred forty-six gigaPascals for the DMA prime plus water ice VII assembly gives us a hard structural boundary for what those materials can handle in simulation.

Kai: That’s right, and the stoichiometry estimates we got from comparing it to AMH-DIMA suggest that one ammonia to one water ratio is likely stable in that specific bcc structure.

Mira: It’s a useful piece of data because it helps us understand the fundamental chemistry of these high-pressure ammonia hydrates.

Lev: For running simulations, being able to use those equation of state parameters derived from fitting the P-V data makes our error analysis much more reliable for predicting behavior in real hardware setups.

Kai: So we've seen how compression rate shifts those three phase assemblages and what the stability limits actually are in this paper.

Mira: It really solidifies the picture that kinetic control is essential when modeling these hydrogen bonded systems, pointing toward a more intricate chemistry involving ammonia impurities incorporated into ice structures at high pressure.

Lev: And for future work, they’ll need to characterize that bcc DMA prime structure more deeply since they only inferred it's stable, not fully determined its atomic arrangement.

Kai: So this paper gives us a much clearer way to predict the phase behavior of these ammonia water solutions under extreme conditions by looking at compression dynamics.

Mira: It’s vital for anyone modeling planetary interiors where these compounds might exist under immense pressure because it shows the real-world consequences of those kinetic factors.

Lev: I think we should keep an eye on how they refine those structural identity questions, because that’s where the next big piece of information for us will likely come from.

A. Mondal, K. Mohrbach, K. Glazyrin, H.-P. Liermann, C. Sanchez-Valle

Institut für Mineralogie, University of Münster · Department of Physics, NIT Agarata · Deutsches Elektronen-Synchrotron DESY

cond-mat.mtrl-sci

Submitted: 2025-12-05

Updated: 2025-12-05

Comments: Main text (17 Pages and 6 figures) and Supplementary information (Figure S1-S3 and Table S1-S2)

DOI: 10.1103/mw4m-12fz

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 80/100

The gist: Understanding the crystallization pathways of water-rich ammonia-water (NH3-H2O) solutions and the stability of ammonia hydrates is key to unraveling the behavior of complex hydrogenbonding networks…

Key concepts

Compression Rate Dependence
This refers to the speed at which the diamond anvil cell is compressed. The study found that different speeds lead to fundamentally different crystallization outcomes for 25 wt% NH3 solutions. Slow compression stabilizes one phase, while fast compression promotes another, showing that the rate of change in pressure significantly influences the resulting crystal structure.
Phase Assemblages
These are the distinct combinations of phases observed under specific pressure and compression conditions. The study identified three main assemblages: one involving AHH-II and ice VII at low rates, a bcc DMA' phase with ice VII at high rates, and a mixture of both in between. Understanding these combinations is key to predicting material behavior under extreme conditions.
Equation of State (EoS) Fitting
The EoS is a mathematical model used to describe how the pressure and volume of a substance change together. By fitting this model to the experimental data from phases like DMA' and AHH-D(I)MA, researchers could compare their physical properties, such as bulk modulus, with known ammonia hydrate phases, confirming structural similarities.
NH3 Impurities in Ice VII Lattice
The presence of ammonia molecules within the structure of water ice (ice VII) was observed when DMA' formed. This suggests that NH3 impurities can be incorporated into the ice lattice under high pressure, which alters the overall compression behavior of the water ice and is a key finding for understanding high-pressure chemistry.

Terminology

Summary

Understanding the crystallization pathways of water-rich ammonia-water (NH3-H2O) solutions and the stability of ammonia hydrates is key to unraveling the behavior of complex hydrogenbonding networks as well as for planetary interior modelling. p. 0 Here, we investigate the effect of compression rates on the crystallization pathways of 25 wt% NH3 aqueous solutions at room temperature using dynamically compressed diamond anvil cells (dDAC) coupled with time-resolved X-ray diffraction. p. 0 We show that compression rates exceeding 0. p. 05 GPa/sec promote direct crystallization of a body-centered cubic (bcc) phase (DMA’) with possible AMH stoichiometry coexisting with H2O ice VII, while rates below 0. p. 02 GPa/sec stabilize monoclinic NH3-rich AHH-II and ice VII phases. p. 0 Intermediate rates between 0. p. 02-0.5 GPa/sec produce a mixture of both hydrates alongside ice VII, hence demonstrating the role of compression rate on the crystallization sequence of ammonia solutions. p. 0

Compressional Rate Dependence

The study reveals three distinct phase assemblages depending on the compression rate:

  1. monoclinic AHH-II and ice VII assembly below 0.2 GPa

  2. a bcc DMA phase (hereafter DMA’) and ice VII assembly above 0.5 GPa

  3. AHH-II + DMA’ + ice VII between 0.2 and 0.5 GPa

The compression rate plays a pivotal role in the crystallization pathway of ammonia-water solutions containing 25 wt% NH3, leading to the formation of distinct phase assemblages. Compression rates above 0. p. 05 GPa/sec favor the direct formation of the bcc DMA’ phase. p. 1 Conversely, compression rates below 0. p. 02 GPa/sec stabilize the monoclinic AHH-II phase. p. 0

Phase Stability Evolution

The compression behavior of the AHH-II + ice VII and DMA’ + ice VII phase assemblages were examined further up to 93 GPa and 146 GPa, respectively. The bcc structure of DMA’ phase is stable up to 146 GPa without any evidence of phase transformations. p. 6

Stoichiometric Estimation

The pressure dependence of the DMA’ phase volumes suggests a 1NH3:1H2O composition. The good agreement between the compression curve of the DMA’ phase and that of the AMH-DIMA phase suggests a 1NH3:1H2O composition for the DMA’ phase. p. 8

Equation of State Fitting

The P-V data for both AHH-D(I)MA and DMA’ phases could be described with a single EoS-fit. The EoS parameters for the DMA’ phase display a higher bulk modulus value compared to both the AHH-D(I)MA and ADH-DMA phases, but are in close agreement to those of AMH-DIMA phase. p. 9 p. 9

Impurities and Lattice Effects

The presence of H2O ice VII coexisting with the DMA’ phase alters the overall compression behavior of H2O ice observed in these runs. This deviation could be explained by the incorporation of NH3 impurities into the ice VII crystal lattice. p. 0

Conclusion

Our study provides a comprehensive understanding on the influence of compression rates on the crystallization pathways of H2O-rich NH3-H2O solutions (25 wt% NH3), resolving discrepancies in the previously reported phase relations and crystallization processes. With the Le Bail refinements, we demonstrate that compression rates significantly affect the crystallization of distinct ammonia hydrate phases. p. 5 The results suggest the incorporation of NH3 into the H2O ice VII lattice at high pressures. p. 0

Pruning redundant reasoning tokens

The outcomes of the compression-rate dependent crystallization experiments of the 25 wt% NH3-H2O solutions (dDAC runs) are summarized in Table I. The XRD maps recorded at the highest pressure plateau (Figure S3), along with the intensity plots displaying the stacking of integrated diffractograms collected during the ramp compression runs (Figure 1) reveal the formation of a bcc DMA-like phase14, hereafter referred to as DMA’, coexisting with ice VII, at compression rates exceeding 0. p. 4 p. 45 GPa/sec. This ammonia hydrate phase is identified by the characteristic bcc (110) reflection present at the 2θ angle of 11. p. 4 p. 479o. Although neutron diffraction data is unavailable to confirm the disordered nature of the phase, we infer this phase to be DMA-like, which appears to be thermodynamically stable phase of ammonia hydrates at high pressure14. p. 4 p. 4

How the training signal is built

The P-V data for the AHH-D(I)MA phase are in good agreement with previous literature data14,33,34. Moreover, the volume (per molecule) of AHH-D(I)MA is found to be higher than that of the bcc DMA’ phase, with differences of approximately 7% at 30 GPa. p. 8

Where the gains come from

The compression rate-dependent crystallization experiments resolve discrepancies in the phase relations previously reported for the crystallization of H2O-rich NH3-H2O solutions14. The findings are crucial for modeling the phase behavior of H2O-rich planetary bodies and evidence the complex chemistry and physics of icy exoplanets and moons. p. 0

The compression rate-dependent crystallization experiments of the 25 wt% NH3-H2O solutions (dDAC runs) are summarized in Table I. The XRD maps recorded at the highest pressure plateau (Figure S3), along with the intensity plots displaying the stacking of integrated diffractograms collected during the ramp compression runs (Figure 1) reveal the formation of a bcc DMA-like phase14, hereafter referred to as DMA’, coexisting with ice VII, at compression rates exceeding 0.5 GPa/sec. This ammonia hydrate phase is identified by the characteristic bcc (110) reflection present at the 2θ angle of 11.79o. Although neutron diffraction data is unavailable to confirm the disordered nature of the phase, we infer this phase to be DMA-like, which appears to be thermodynamically stable phase of ammonia hydrates at high pressure14.

The P-V data for both AHH-D(I)MA and DMA’ phases could be described with a single EoS-fit. The EoS parameters for the DMA’ phase display a higher bulk modulus value compared to both the AHH-D(I)MA and ADH-DMA phases, but are in close agreement to those of AMH-DIMA phase.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Phase Identification based on Compression Rate: The AI system can accurately predict whether a 25 wt% NH3-H2O solution will crystallize into AHH-II + H2O ice VII (below 0.2 GPa/sec), a bcc DMA' phase (above 0.5 GPa/sec), or a mixture of both (between 0.2 and 0.5 GPa/sec) based on the applied compression rate, as shown in Figure 1 and Table I.

  2. Stoichiometry Estimation for Novel Phases: The system can estimate the probable stoichiometry of the DMA' phase by comparing its pressure-volume curve with that of known phases like AMH-DIMA, suggesting a 1NH3:1H2O composition based on the good agreement between these two compression curves within their respective uncertainties.

  3. High Pressure Stability Prediction: The AI can predict the stability limits of the bcc DMA' phase up to 146 GPa and the AHH-II + H2O ice VII assembly up to 93 GPa, distinguishing them from other phases based on their corresponding P-V data in Figure 5.

  4. Incorporation of Impurities Modeling: The system can model the effect of NH3 impurities on H2O ice lattice by predicting volume deviations in the compression curve, noting that the presence of large cations like Ca2+ and Na+ induce lattice compression, i.e., volume reduction, CH3OH incorporation leads to expansion of the ice VII lattice.

  5. Equation of State Fitting: The system can perform a 3rd order Birch-Murnaghan equation of state fit to P-V datasets for AHH-D(I)MA and DMA' phases, comparing the resulting bulk modulus values with literature data to confirm the similar nature and composition of the DMA’ and AMH-DIMA phase.

Sources

Related papers