Experimental methods to measure thermal hysteresis of martensite-austenite transition in bulk-Cu-Zn-Al composition gradient single crystals

arXiv:2510.17297 · cond-mat.mtrl-sci · Submitted 2025-10-20 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Experimental methods to measure thermal hysteresis of martensite-austenite transition in bulk-Cu-Zn-Al composition gradient single crystals".

Mira: Here's the gist of the paper. Exploration of the hysteresis of martensite-austenite transition in bulk β-Cu-Zn-Al single crystals proposes an experimental high throughput methodology to explore fine composition variations and local measurements to investigate the austenite-martensite microstructure during transformation The authors propose an experimental high throughput methodology based on an original route to process bulk gradient composition single crystals to investigate fine variation of composition range coupled with local measurements of the austenite-martensite microstructure by light microscopy during the transformation This processing route involves a combined liquid dealloying, bridgman-like growth and abnormal grain growth by diffusion Homogeneous CuZnAl alloys were prepared by melting encapsulated Cu, Zn, and Al elements with a purity of 4.5 N in a quartz-glass capsule at low pressure (700 mbar of Ar) For generating bulk concentration gradients two methods were used, including diffusion couple bonding A simpler and original method was developed where a 1.5 mm high Zn cylinder is placed on a 10 mm high CuZnAl cylinder so that the whole corresponds to a target composition This method produces a single crystal with a gradient in chemical composition processed with this method, reaching around 1.3 at% cm-1 for Zn, 1.1 at%/cm-1 for Al, and 0,2 at%/cm-1 for Cu Characterization of Transformation Hysteresis The methodology allows for the measurement of thermal hysteresis using differential interference contrast light microscopy coupled with a non conventional calorimeter setup This technique is compared with standard Differential Scanning Calorimetry (DSC) measurements to quantitatively link various aspects of the austenite-martensite transition with mesoscale microstructure evolution The thermal hysteresis loop is obtained by integrating the inner area of martensite fraction versus Temperature in cooling/heating ramps, which can also be obtained by equation (1) with evaluations of characteristic temperatures The comparison between microscopy and DSC showed that the hystereses are very similar despite a small transient temperature shift Results on Composition Dependence Several samples with composition gradients were measured by optical observation, and each measured sample exhibits ΔThyst values whose dependence on composition differs A local minimum of the hysteresis width as a function of position, and therefore composition, is shown for sample Grad.1 in Figure 5 The minimum of ΔThyst is observed over 1 mm width which covers a range of 0.13 at % in Zn and 0.11 at% in Al around Cu68.85Zn13.15Al18 in Grad.2 sample This local minimum matches with observed dependencies of characteristic transition temperatures where strong variations can be observed on very narrow concentration range below 1 at% A consistent trend of a local minimum around e/a=1.49 is found for the Grad.1 and Grad.2 investigated composition ranges The investigations support several key conclusions regarding the study of β-CuZnAl alloys a simple processing route is detailed for growing bulk single crystals in order to explore the composition range of beta brass CuZnAl with controlled composition gradients (down to 0.1 at % / mm) A local high-throughput method based on light microscopy was developed to monitor the thermal hysteresis of transitions and enable the evaluation of characteristic temperatures and thermal hysteresis The exploration of non-standard composition ranges is demonstrated, and local minima of ΔThyst are observed for fine variations in composition This methodology paves the way for the experimental investigation of new compositions in Cu-based alloys for elasto-caloric applications The work suggests that systematic investigations with complementary high resolution diffraction x-ray of the crystallographic structures of the corresponding austenite and martensite are needed to better understand the relationship between reversibility and composition Acknowledgments Authors kindly acknowledge Univ.

Kai: Grenoble Alpes for providing an IRGA PhD grant for one of us (O.N) as well as Institut Carnot Energics for complementary fundings (CASTLE project) The European Synchrotron Radiation Facility (ESRF) is acknowledged for provision of beam time on IF beamline Fruitfull discussions with A.Tolley, G.

Title and authors: Kai: So, Mira, this paper is talking about experimental methods to measure thermal hysteresis in bulk copper zinc aluminum composition gradient single crystals. It's about finding ways to explore the model beta copper zinc aluminum system.

Mira: Right, it proposes an experimental high throughput methodology using a route to process bulk gradient composition single crystals and local measurements of the austenite martensite microstructure during transformation. It aims to investigate fine variation of composition range coupled with local measurements.

Lev: From my side, I'm thinking about how much overhead that processing route adds before you even get to the measurement part. We need to consider if that complexity is manageable for real hardware testing or just a lab setup thing.

Kai: Exactly, and the paper details this original processing route involving liquid dealloying, bridgman-like growth, and abnormal grain growth by diffusion. They made homogeneous copper zinc aluminum alloys by melting encapsulated copper zinc and aluminum elements with a purity of four point five percent in a quartz glass capsule at low pressure of seven hundred mbar of argon.

Mira: They also developed two methods for generating bulk concentration gradients, one being diffusion couple bonding, and another simpler original method where they placed a one point five millimeter high zinc cylinder on a ten millimeter high copper zinc aluminum cylinder so that the whole corresponds to a target composition.

Lev: That specific geometry for creating the gradient sounds like it's designed to produce single crystals with fine variation, which is what you need if you want to measure local microstructural changes accurately. I wonder how stable those gradients are during the entire growth process and subsequent thermal cycling.

Kai: They reached around one point three at percent zinc, one point one at percent aluminum, and zero point two at percent copper with this method. The paper then moves on to how they characterize the transformation hysteresis using differential interference contrast light microscopy coupled with a non conventional calorimeter setup.

Mira: They are comparing this technique against standard differential scanning calorimetry measurements to quantitatively link various aspects of the austenite martensite transition with mesoscale microstructure evolution. They define thermal hysteresis as the average value of the width of the hysteresis cycle in temperature, which is defined by equation one.

Lev: Comparing microscopy to differential scanning calorimetry is a key part because we know DSC measures bulk energy changes, but light microscopy lets you see exactly what's happening at the micron scale with the martensite fraction. That should give us a better picture of how the transformation happens locally.

Kai: The comparison showed that the hysteresis loops are very similar despite a small transient temperature shift between the two methods. They also measured several samples with composition gradients and each sample exhibited delta theta values whose dependence on composition differed.

Title and authors: Mira: They show a local minimum of the hysteresis width as a function of position, and therefore composition, for sample grad one in figure five. This minimum is observed over one millimeter width which covers a range of zero point thirteen at percent zinc and zero point eleven at percent aluminum around copper sixty-eight point eight five zinc thirteen point one five aluminum eighteen.

Lev: That finding about the local minimum matching observed dependencies of characteristic transition temperatures sounds important for predicting where you'll see the most favorable transformation behavior in terms of hysteresis width. It tells us that composition isn't just a flat line affecting things; there are specific regions where the system behaves differently.

Kai: They found a consistent trend of a local minimum around e over a equals one point four nine for the grad one and grad two investigated composition ranges. This suggests some kind of structural compatibility criterion is being met in those specific compositional zones.

Mira: So, they conclude that this methodology supports several key conclusions regarding the study of beta copper zinc aluminum alloys: a simple processing route is detailed for growing bulk single crystals to explore the composition range of beta brass copper zinc aluminum with controlled composition gradients down to zero point one at percent per millimeter.

Lev: And they developed a local high throughput method based on light microscopy to monitor the thermal hysteresis of transitions and enable the evaluation of characteristic temperatures and thermal hysteresis, which is a useful tool for mapping out the transformation landscape.

Kai: They also demonstrated the exploration of non standard composition ranges, observing local minima of delta theta for fine variations in composition around copper sixty-eight point eight five zinc thirteen point one five aluminum eighteen. This opens up avenues for studying new compositions in copper-based alloys for elasto-caloric applications.

Mira: The work suggests that systematic investigations with complementary high resolution diffraction x ray of the crystallographic structures of the corresponding austenite and martensite are needed to better understand the relationship between reversibility and composition. That's where they point next, looking at structure itself.

Lev: I agree, knowing exactly what those crystal structures look like under those specific gradient conditions would really help us connect the hysteresis measurements directly to crystallographic supercompatibility conditions they mentioned earlier.

Kai: So, to wrap up on this paper: we have an experimental high throughput methodology for exploring the model beta copper zinc aluminum system using bulk gradient single crystals and local light microscopy measurements of the austenite martensite microstructure during transformation. It shows that composition dependence is complex, with local minima in hysteresis width around certain compositions.

Mira: And they've linked this to mesoscale evolution by comparing light microscopy to differential scanning calorimetry, finding very similar thermal hysteresis values despite a small transient temperature shift.

Lev: Ultimately, the implications are that we can experimentally probe fine composition variations and link them directly to the local microstructure during phase transformation, which is crucial for understanding how these materials perform in applications like elasto-caloric devices.

Kai: That's it for this paper on experimental methods to measure thermal hysteresis of martensite-austenite transition in bulk-Cu-Zn-Al composition gradient single crystals. We'll see what the next set of papers brings.

The paper's summary: Kai: So, what we're looking at is how they've set up an actual experiment to measure the thermal hysteresis in these copper zinc aluminum alloys when you change the composition gradually across a single crystal sample.

Mira: Exactly, it’s about taking that complex phase transition—the austenite to martensite switch—and measuring how wide that temperature gap is, while simultaneously mapping out exactly what’s happening at the microscopic level on that gradient.

Lev: From an error correction standpoint, the real challenge here is linking those local measurements from the light microscopy directly to a measurable thermodynamic quantity like the transition temperatures themselves.

Kai: The paper shows they compared their method—light microscopy with a non conventional calorimeter setup—against standard differential scanning calorimetry, and they found that despite some small temperature shifts during the transition, the resulting hysteresis loops looked very similar.

Mira: That similarity is actually quite telling, because it suggests that what you see at the microscale under light microscopy is really capturing the same physics that standard bulk calorimetry measures when you integrate those inner areas of martensite fraction versus temperature.

Lev: But there's a catch; they aren't just looking at a single point; they’re looking across a whole composition gradient, and they found that the hysteresis width doesn't change smoothly with composition.

Kai: Right, because they spotted these local minima in the hysteresis width as you move along the gradient. They found this minimum happens over a one millimeter width where the zinc content is around zero point thirteen at percent and aluminum is around zero point eleven at percent near copper sixty-eight point eight five zinc thirteen point one five aluminum eighteen.

Mira: That finding connects directly to what we were discussing earlier about composition dependence; it means that for certain compositions, the transformation process itself becomes much more stable or exhibits a different dynamic behavior compared to neighboring points.

Lev: If you're building real hardware, knowing where those minima are is huge because it tells you exactly which compositional range you need to target if you want the most reliable performance in an elasto-caloric application.

Kai: So, what this all means for the world is that we can now experimentally probe these fine composition variations and link them directly to the local microstructure during a phase change, which is essential for designing better materials for things like heat pumps or cooling devices.

Mira: It opens up a new pathway to systematically investigate novel compositions in copper-based alloys by using this high throughput method, and they suggest we need to pair this with high resolution X ray diffraction to finally connect the hysteresis measurements with the actual crystallographic structures of the austenite and martensite phases.

Lev: That's where we go next; understanding the structure is what will let us really nail down that relationship between reversibility and composition.

The paper's improvements: Tom: So, we're looking at what the authors suggest as improvements for their experimental setup on measuring that thermal hysteresis across composition gradients in those bulk crystals.

Kai: They point out that while their method is high throughput, it still needs to be paired with something else to truly validate the results against theoretical expectations.

Mira: Right, they emphasize that the next big step is using complementary high resolution X ray diffraction to look at the actual crystallographic structures of both the austenite and martensite phases.

Lev: I see that as a necessary check; without knowing what’s actually happening structurally—what those crystal lattices look like—we can’t fully understand how composition dictates the transition dynamics.

Kai: It's about getting that structural data to finally connect the hysteresis measurements with the relationship between reversibility and composition they mentioned earlier.

Mira: Exactly, because right now they have a lot of interesting experimental data from these light microscopy measurements, but the theory needs that structural context to fully grasp what’s going on at the atomic level when we change the mix.

Lev: For real hardware testing, this means if we were designing a device based on these alloys, we’d need to run simulations that incorporate those structural constraints so they match what's actually being measured experimentally.

Kai: The implication is that this isn't just about measuring a number; it’s about building a complete picture where the bulk measurement, the microstructural observation, and the atomic structure all talk to each other.

Mira: It suggests that while this single study shows promising local minima for composition dependence, we need systematic investigations across different compositions to map out those trends more thoroughly.

Lev: If we can validate these findings with structural data from X ray diffraction, it gives us a much stronger basis for predicting where the most favorable transformation behavior will occur in new materials.

Conclusion: Kai: So we’ve covered how they set up that experimental high throughput methodology for exploring composition variations in those bulk copper zinc aluminum single crystals to measure the thermal hysteresis of the martensite austenite transition.

Mira: That’s right, and what it boils down to is proving you can link local microstructural evolution directly to bulk thermodynamic measurements using light microscopy and a calorimeter setup.

Lev: From an error correction angle, this really shows how important it is to have high fidelity measurements at the mesoscale when dealing with these complex phase transitions in real hardware applications.

Kai: And they showed that the results are quite consistent with standard differential scanning calorimetry even though there was some small transient temperature shift between the two techniques.

Mira: The implication is that this method gives us a powerful way to map out how composition affects the transformation landscape by looking at those local minima in the hysteresis width across a gradient.

Lev: If we were designing something, knowing exactly where those minima are helps us target the most stable compositions for reliable operation, which is huge for real-world engineering overhead.

Kai: It also points toward a need for more systematic studies with complementary high resolution X ray diffraction to tie that hysteresis data back to the actual crystal structure of the austenite and martensite phases.

Mira: Exactly, because without knowing those structures, we can’t fully understand the relationship between composition and how reversible that phase transition actually is.

Lev: I think what this paper really changes for me is showing a feasible experimental route to probe these compositional effects, which gives us something concrete to work with when building error-correcting models for materials.

Kai: So, in summary, this paper on "Experimental methods to measure thermal hysteresis of martensite-austenite transition in bulk-Cu-Zn-Al composition gradient single crystals" provides a practical tool to explore fine composition variations and link them to local microstructure measurements.

Mira: It opens up avenues for experimental investigation of new compositions for elasto-caloric applications based on the finding that local minima in hysteresis width correspond to specific compositional ranges.

Lev: I think the next step is definitely moving into those high resolution structural studies because that’s where we can really ground these dynamic measurements in something physical.

O.Goisot, H.vanLandeghem, R.Haettel, F.Robaut, O.Robach, L.Porcar, ÜmVerdier

University of Grenoble Alpes, CNRS, Grenoble INP, Institute of Engineering University of Grenoble Alpes, SIMaP · University of Grenoble Alpes, CNRS, Grenoble INP, Institute Néel UPR 2940 · University of Grenoble Alpes, CNRS, CEA

cond-mat.mtrl-sci

Submitted: 2025-10-20

Updated: 2026-11-15

Comments: 23 pages, 8 figures

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 80/100

The gist: Exploration of the hysteresis of martensite-austenite transition in bulk β-Cu-Zn-Al single crystals proposes an experimental high throughput methodology to explore fine composition variations and…

Key concepts

Thermal Hysteresis ($\Delta T_{hyst}$)
This is the difference in temperature between heating and cooling cycles during a phase transformation, specifically the austenite-martensite transition. It measures the energy barrier required for the material to change its microstructure. Measuring this helps link microscopic changes in crystal structure to macroscopic thermal behavior.
Composition Gradient Single Crystals
These are bulk crystals where the chemical composition (the ratio of Cu, Zn, and Al) is intentionally varied smoothly across a physical distance. The authors used a specific method involving placing cylinders of different materials together to create these controlled gradients for detailed local analysis.
Light Microscopy Monitoring
This technique involves using optical microscopy to observe the microstructure (the arrangement of austenite and martensite phases) as the material is heated or cooled. By analyzing images perpendicular to the composition gradient, researchers can quantitatively link specific microstructural features, like martensite size, directly to the measured thermal hysteresis.
Local Minimum of $\Delta T_{hyst}$
This phenomenon occurs when the thermal hysteresis width drops significantly over a very narrow range of chemical composition. Finding these local minima allows researchers to pinpoint precise compositions where the transformation behavior is particularly sensitive or favorable for applications.

Terminology

Summary

Exploration of the hysteresis of martensite-austenite transition in bulk β-Cu-Zn-Al single crystals proposes an experimental high throughput methodology to explore fine composition variations and local measurements to investigate the austenite-martensite microstructure during transformation

Methodology for Composition Control

The authors propose an experimental high throughput methodology based on an original route to process bulk gradient composition single crystals to investigate fine variation of composition range coupled with local measurements of the austenite-martensite microstructure by light microscopy during the transformation This processing route involves a combined liquid dealloying, bridgman-like growth and abnormal grain growth by diffusion Homogeneous CuZnAl alloys were prepared by melting encapsulated Cu, Zn, and Al elements with a purity of 4.5 N in a quartz-glass capsule at low pressure (700 mbar of Ar) For generating bulk concentration gradients two methods were used, including diffusion couple bonding A simpler and original method was developed where a 1. p. 2

Where the paper says it

Processing of bulk single crystal with concentration gradients Homogeneous CuZnAl alloys were prepared by melting encapsulated Cu, Zn, and Al elements with a purity of 4. 5 N in a quartz-glass capsule at low pressure (700 mbar of Ar).

5 mm high Zn cylinder is placed on a 10 mm high CuZnAl cylinder so that the whole corresponds to a target composition This method produces a single crystal with a gradient in chemical composition processed with this method, reaching around 1. p. 2
Where the paper says it

To bypass these two drawbacks, a simpler and original method has been developed, which principle is given Figure 1. 5 mm high Zn cylinder(A)is placed on a 10 mm high Cu79Al21 cylinder(A’)so that the whole corresponds to a target composition (C)Cu69Zn14Al17.

3 at% cm-1 for Zn, 1.1 at%/cm-1 for Al, and 0,2 at%/cm-1 for Cu

Characterization of Transformation Hysteresis

The methodology allows for the measurement of thermal hysteresis using differential interference contrast light microscopy coupled with a non conventional calorimeter setup This technique is compared with standard Differential Scanning Calorimetry (DSC) measurements to quantitatively link various aspects of the austenite-martensite transition with mesoscale microstructure evolution The thermal hysteresis loop is obtained by integrating the inner area of martensite fraction versus Temperature in cooling/heating ramps, which can also be obtained by equation (1) with evaluations of characteristic temperatures The comparison between microscopy and DSC showed that the hystereses are very similar despite a small transient temperature shift

Results on Composition Dependence

Several samples with composition gradients were measured by optical observation, and each measured sample exhibits ΔThyst values whose dependence on composition differs A local minimum of the hysteresis width as a function of position, and therefore composition, is shown for sample Grad.1 in Figure 5 The minimum of ΔThyst is observed over 1 mm width which covers a range of 0. p. 4

Where the paper says it

A local minimum is observed that would not have been found with discrete compositions investigations. The minimum of ΔThyst is observed over 1 mm width which covers a range of 0.

13 at % in Zn and 0.11 at% in Al around Cu68. p. 4
Where the paper says it

13 at % in Zn and 0. 11 at% in Al around Cu68.

85Zn13.15Al18 in Grad. p. 4
Where the paper says it

11 at% in Al around Cu68. 15Al18 in Grad.

2 sample This local minimum matches with observed dependencies of characteristic transition temperatures where strong variations can be observed on very narrow concentration range below 1 at% A consistent trend of a local minimum around e/a=1. p. 4
Where the paper says it

This matches with observed dependencies of characteristic transition temperatures in elasto-caloric materials (NiTiCu, Cu based alloys ) where strong variations can be observed on very narrow concentration range (below 1 at%) [8,10,11]. Moreover a consistent trend of a local minimum around e/a=1.

49 is found for the Grad. p. 4
Where the paper says it

1 and Grad. p. 2

Where the paper says it

We applied this method using 4. 5 N purity elements and obtained a gradient sample (Grad.

A local minimum is observed that would not have been found with discrete compositions investigations.

1 and Grad.2 investigated composition ranges

Conclusions and Implications

The investigations support several key conclusions regarding the study of β-CuZnAl alloys

** a simple processing route is detailed for growing bulk single crystals in order to explore the composition range of beta brass CuZnAl with controlled composition gradients (down to 0.1 at % / mm) **

** A local high-throughput method based on light microscopy was developed to monitor the thermal hysteresis of transitions and enable the evaluation of characteristic temperatures and thermal hysteresis **

** The exploration of non-standard composition ranges is demonstrated, and local minima of ΔThyst are observed for fine variations in composition **

This methodology paves the way for the experimental investigation of new compositions in Cu-based alloys for elasto-caloric applications The work suggests that systematic investigations with complementary high resolution diffraction x-ray of the crystallographic structures of the corresponding austenite and martensite are needed to better understand the relationship between reversibility and composition

Acknowledgments

Authors kindly acknowledge Univ. Grenoble Alpes for providing an IRGA PhD grant for one of us (O. p. 5

Where the paper says it

Acknowledgments Authors kindly acknowledge Univ. Grenoble Alpes for providing an IRGA PhD grant for one of us (O.

N) as well as Institut Carnot Energics for complementary fundings (CASTLE project) The European Synchrotron Radiation Facility (ESRF) is acknowledged for provision of beam time on IF beamline Fruitfull discussions with A. p. 5
Where the paper says it

N) as well as Institut Carnot Energics for complementary fundings (CASTLE project). We acknowledge the European Synchrotron Radiation Facility (ESRF) for provision of beam time on IF beamline (experiment A32-1-208 (2025)).

Tolley, G.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Develop an experimental high throughput methodology for exploring model beta-Cu-Zn-Al system by combining a original route to process bulk gradient composition single crystals with local measurements of the austenite-martensite microstructure by light microscopy during transformation. This allows for rapid identification of interesting compositions on composition gradient samples while minimizing the impact of defects and microstructural conditions that may differ for each sample.

  2. Implement a high throughput method based on light microscopy to monitor thermal hysteresis by integrating the image processing results perpendicular to the concentration gradient. This method can quantitatively link various aspects of the austenite-martensite transition with mesoscale microstructure evolution, providing a more sensitive measurement than standard differential scanning calorimetry for capturing micron size martensite.

  3. Create an AI system capable of predicting the dependence of thermal hysteresis width on composition by analyzing local minima observed in the transformation hysteresis as a function of position or composition. This system can leverage the observed trend that a local minimum of the hysteresis width as a function of position, and therefore composition, is shown for sample Grad.1.

  4. Design an AI tool to correlate the measured thermal hysteresis profiles from different measurement methods with thermodynamic parameters like characteristic transition temperatures (Ms, Mf, As and Af). This system can learn to distinguish between feedback is applied by the heat flow to maintain a constant heating rate in DSC versus the transient temperature shift occurs in the optical measurement during the transition.

  5. Develop an AI model that maps composition variations on ternary diagrams to predicted hysteresis widths, specifically focusing on finding compositions that meet criteria for crystallographic supercompatibility. This system can utilize data showing a local minimum is observed over 1 mm width which covers a range of 0.13 at % in Zn and 0.11 at% in Al around Cu68.85Zn13.15Al18.

Abstract

Improvement of functional and structural fatigue endurance for applications of ferroelastic materials requires an optimization of their composition. We propose an experimental methodology to explore the model-Cu-Zn-Al system. It is based on an original route to process bulk gradient composition single crystals to investigate fine variation of composition range coupled with local measurements of the austenite-martensite microstructure by light microscopy during the transformation. The latter method is compared with differential scanning calorimetry measurements. The methodology is applied to different narrow ranges (up to 4 at%) of composition of standard CuZnAl shape memory alloys where local fluctuations of hysteresis of 3 K are observed.

Related papers