Ultra-transient grating spectroscopy for visualization of surface acoustics

arXiv:2510.10696 · cond-mat.mtrl-sci · Submitted 2025-10-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Ultra-transient grating spectroscopy for visualization of surface acoustics".

Mira: Here's the gist of the paper. Ultrasonic wave propagation across material surfaces reveals essential information about the materials’ elastic behavior The resulting experimental angular dispersion maps strikingly replicate the theoretical frequency-domain Green’s functions Experimental Technique and Novelty Ultra-transient grating spectroscopy (UTGS) is introduced as a powerful tool for detailed contactless characterization of anisotropic solids This technique focuses on early-time thermoacoustic phenomena in the TGS experiment, revealing oscillations with at least an order of magnitude shorter lifetimes than classical transient timescales The optical diffraction signal from these ‘ultra-transient’ gratings enables capturing the surface acoustic response with exceptional detail Enhancements for Ultra-Transient Features To enhance the ultra-transient features, several modifications were implemented in the TGS experiment These enhancements included: We utilized strongly elliptical beam shapes to maximize the number of fringes with strong excitation The detection beam was shaped similarly to ensure information from locations of maximal excitation 23 We strengthened the diffraction efficiency by using two distinct laser wavelengths (1064 nm for pump and 532 nm for probe) This choice enhanced both sensitivity and k-vector selectivity of the measurement 8 We utilized an in-house designed combination of Si PIN photodiodes with 60 dB amplifiers to increase the signal-to-noise ratio The frequency bandwidth of both photodiodes and amplifiers was set to 1 GHz for full utilization 8 We maximized the signal-to-noise ratio through extensive averaging, up to 50 thousand shots per direction This resulted in a scanning time for an angular-dispersion map of approximately 5 hours 4 Theoretical Foundation and Comparison The frequency-domain surface elastodynamic Green’s function is the theoretical object representing the response of the surface The TGS maps obtained with the modified setup bring rich information about the elastic behavior of the material, allowing for direct comparison with theory The measured response to the TGS source should be described by the G13 component of the frequency-domain Green’s tensor Gi j(k∥,ω) 3 The agreement with the experimental maps is striking, regardless of which material and which cut is chosen 7 The richness of the information allows for the determination of anisotropic elastic coefficients ci j through an inverse approach, minimizing the mismatch between experimentally determined wavespeeds v exp n (m) and calculated values v calc n (m,ci j) 17 Interpretation of Green’s Function Features The finer structure of the frequency-domain Green’s function corresponds to the behavior of partial waves that compose the elastodynamic response Sharp changes in the ultra-transient part of the signal arise from conversions between homogeneous and evanescent partial waves The partial wave approach enables constructing the displacement fields corresponding to individual points in the G13 plot, allowing direct calculation of which orientations and types of elastic strain field are carried by the individual features 4 Sharp features in the TGS maps can be interpreted as changes in the types of partial waves, such as conversions from evanescent to homogeneous solutions 3 The analysis confirms that the details in the TGS map indeed arise from phenomena that are transient with respect to the lifetime of the transient grating 8 The UTGS approach provides an unprecedented experimental capability to visualize the complete surface acoustic response in elastically anisotropic materials This method overcomes limitations of other techniques by using interference-pattern excitation which leads to strictly harmonic generation of coherent waves with well-defined wave-vector orientations The all-optical contactless nature of the UTGS analysis predetermines its use under various extreme conditions, opening a novel pathway for studying the relationship between elastic behavior and functional performance in newly developed materials 14 33 The single-crystalline samples of nickel were acquired from MaTecK with the accuracy of the crystallographic orientation of < 0.1◦ The considered density was ρ = 8.9gcm−3, and the elasticity of nickel was taken as c11 = 251.9GPa, c12 = 157.7GPa, and c44 = 124.3GPa The Fe3Al samples were cut from an intermetallic alloy (exact composition Fe–28 at.%Al–4 at.% Cr) manufactured by Bridgman growth at the Institute of Physics, Czech Academy of Sciences The density was ρ = 6.62gcm−3, and elasticity c11 = 179.5GPa, c12 = 119.6GPa, and c44 = 129.9GPa Transient Grating Spectroscopy The measurements were performed using the optical path outlined in Figure 1(a), which is a classical arrangement for TGS The pump pattern was created by interference of strongly elliptical laser beams (approximately 0.8 × 0.1 mm2 in cross-section) in the near infrared range (1064 nm, pulse energy 110 µJ, pulse duration 0.53 ns (FWHM), repetition rate 1 kHz) The nominal acoustic wavelength in the reported measurements was 10 µm, with the exact wavelength calibrated using a known material – for the reported measurement, the calibrated value was 10.064±0.005µm The pulse energy was lowered in the optical path and tuned to be slightly below the ablation limit of the sample (typically below 40 µJ on the sample surface), so that no visible trace was left after the measurement The heat diffusion length (approximated as L = √αt) was well below the acoustic wavelength (10 µm): around 0.48 µm for Ni, and 0.18 µm for Fe3Al at 10 ns after the laser pulse Calculation of the Green’s Function and its Interpretation with respect to the Experiment The frequency-domain surface dynamics calculation was based on the approach by Every et al., which can be summarized as follows For the given tensor of elastic constants Ci jkl, material density ρ, angular frequency ω, and surface wavevector k∥ = (k1,k2), the Christoffel equation Ci jklk jkl −ρω2 δik Uk = 0 (2) gives six solutions for the out-of-plane component of the wavevector k(n) 3, n = 1,…6, with corresponding eigenvectors U(n) The displacement resulting from a spatially and temporally harmonic surface force Fj (acting in the x j-direction and defining k∥ and ω) is then formed as a superposition of these three phase-matched partial waves u(j)i(k∥,ω; x3) = 3 ∑ A(n)j U(n)i exp(ik (n) 3 x3), (i, j = 1,2,3).

Kai: (3) The partial-wave amplitudes A(n)j stem from the stress-strain relationship and the free-surface boundary condition as A(n)j = i ω B−1 (n)j, (j,n = 1,2,3).

Mira: (4) where the boundary condition matrix can be written as B(n)l = C3 jklU(n)k k(n)l ω, (l,n = 1,2,3).

Kai: (5) The surface Green’s function components are then obtained as the displacement amplitude at x3 = 0, which reads Gi j(k∥,ω) = 3 ∑ A(n)i U(n)j.

Paper summary: Kai: So to summarize this paper, "Ultra-transient grating spectroscopy for visualization of surface acoustics," they are focusing on using ultrasonic wave propagation across material surfaces to reveal essential information about how materials behave elastically.

Mira: The core thesis is that the elastodynamic response of the surface can be characterized by the green's function which fully captures all its direction-dependent and frequency-dependent features.

Lev: They claim they present the first direct experimental visualization of this frequency domain angular-resolved green’s function, including all its complex details resulting from elastic anisotropy.

Kai: They achieve this visualization using transient grating spectroscopy, which is a method that's already known for measuring Rayleigh-type surface acoustic waves, but they apply it differently here.

Mira: The key difference is utilizing ultra-transient gratings, which are oscillations with lifetimes at least an order of magnitude shorter than classical transient timescales.

Lev: This technique enables them to capture the surface acoustic response with exceptional detail because these ultra-transient gratings give them access to much faster dynamics.

Conclusion: Kai: Thinking about the title, "Ultra-transient grating spectroscopy for visualization of surface acoustics," it sounds like they’ve found a way to see the very fine details of how waves move across a material's surface.

Mira: They are taking something established, TGS, and pushing it into the ultra-transient regime to visualize the green's function in a way that shows direction-dependent behavior clearly.

Lev: What this means for us is that we can start looking at how subtle elastic differences between materials show up in these surface waves with a level of resolution we haven't had before.

Kai: It moves the study of material science from just measuring bulk properties to directly visualizing the surface dynamics that govern how those materials actually perform.

Mira: It opens up a new way for characterizing functional performance because it links the detailed elastic behavior of the surface to real-world material use under various conditions.

Institute of Thermomechanics, Czech Academy of Science · Faculty of Nuclear Science and Physical Engineering, Czech Technical University in Prague

cond-mat.mtrl-sci

Submitted: 2025-10-12

Updated: 2026-11-05

Comments: Manuscript accepted to Nature Communications. Supplementary material is available as ancillary file

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 78/100

The gist: Ultrasonic wave propagation across material surfaces reveals essential information about the materials’ elastic behavior The resulting experimental angular dispersion maps strikingly replicate the…

Key concepts

Ultra-transient Grating Spectroscopy (UTGS)
This technique is a specialized form of TGS used to study surface acoustics by focusing on very short-lived thermoacoustic oscillations. It captures the surface acoustic response with high detail, revealing information that occurs much faster than classical transient timescales, enabling contactless characterization of anisotropic solids.
Frequency-domain Surface Elastodynamic Green’s Function
This is a theoretical object representing how a material's surface responds to external forces in the frequency domain. The experimental maps generated by UTGS are compared directly to this function; matching the two provides crucial data for calculating the material's elastic properties, like its anisotropic coefficients.
Partial Wave Approach
This method describes the complex elastodynamic response of a surface wave as a superposition of individual partial waves. Sharp features in experimental maps correspond to changes in these waves, such as conversions between homogeneous and evanescent solutions, which helps identify specific strain fields carried by the wave.

Terminology

Summary

Ultrasonic wave propagation across material surfaces reveals essential information about the materials’ elastic behavior The resulting experimental angular dispersion maps strikingly replicate the theoretical frequency-domain Green’s functions

Experimental Technique and Novelty

Ultra-transient grating spectroscopy (UTGS) is introduced as a powerful tool for detailed contactless characterization of anisotropic solids This technique focuses on early-time thermoacoustic phenomena in the TGS experiment, revealing oscillations with at least an order of magnitude shorter lifetimes than classical transient timescales The optical diffraction signal from these ‘ultra-transient’ gratings enables capturing the surface acoustic response with exceptional detail

Enhancements for Ultra-Transient Features

To enhance the ultra-transient features, several modifications were implemented in the TGS experiment These enhancements included:

- We utilized strongly elliptical beam shapes to maximize the number of fringes with strong excitation The detection beam was shaped similarly to ensure information from locations of maximal excitation 23

- We strengthened the diffraction efficiency by using two distinct laser wavelengths (1064 nm for pump and 532 nm for probe) This choice enhanced both sensitivity and k-vector selectivity of the measurement 8

- We utilized an in-house designed combination of Si PIN photodiodes with 60 dB amplifiers to increase the signal-to-noise ratio The frequency bandwidth of both photodiodes and amplifiers was set to 1 GHz for full utilization 8

- We maximized the signal-to-noise ratio through extensive averaging, up to 50 thousand shots per direction This resulted in a scanning time for an angular-dispersion map of approximately 5 hours 4

Theoretical Foundation and Comparison

The frequency-domain surface elastodynamic Green’s function is the theoretical object representing the response of the surface The TGS maps obtained with the modified setup bring rich information about the elastic behavior of the material, allowing for direct comparison with theory

- The measured response to the TGS source should be described by the G13 component of the frequency-domain Green’s tensor Gi j(k∥,ω) 3

- The agreement with the experimental maps is striking, regardless of which material and which cut is chosen 7

The richness of the information allows for the determination of anisotropic elastic coefficients ci j through an inverse approach, minimizing the mismatch between experimentally determined wavespeeds v exp n (m) and calculated values v calc n (m,ci j) 17

Interpretation of Green’s Function Features

The finer structure of the frequency-domain Green’s function corresponds to the behavior of partial waves that compose the elastodynamic response Sharp changes in the ultra-transient part of the signal arise from conversions between homogeneous and evanescent partial waves

- The partial wave approach enables constructing the displacement fields corresponding to individual points in the |G13| plot, allowing direct calculation of which orientations and types of elastic strain field are carried by the individual features 4

- Sharp features in the TGS maps can be interpreted as changes in the types of partial waves, such as conversions from evanescent to homogeneous solutions 3

The analysis confirms that the details in the TGS map indeed arise from phenomena that are transient with respect to the lifetime of the transient grating 8

Conclusion and Future Potential

The UTGS approach provides an unprecedented experimental capability to visualize the complete surface acoustic response in elastically anisotropic materials This method overcomes limitations of other techniques by using interference-pattern excitation which leads to strictly harmonic generation of coherent waves with well-defined wave-vector orientations The all-optical contactless nature of the UTGS analysis predetermines its use under various extreme conditions, opening a novel pathway for studying the relationship between elastic behavior and functional performance in newly developed materials 14 33

Methods

The single-crystalline samples of nickel were acquired from MaTecK with the accuracy of the crystallographic orientation of < 0.1◦ The considered density was ρ = 8. p. 3

Where the paper says it

8 This choice brings other problems – mainly the loss of diffraction efficiency on the phase mask and vulnerability to chromatic aberration due to the large difference of optical wavelengths used. The former can be accepted – the phase mask is optimized for the probe-beam wavelength (532 nm), and the pump laser has a power reserve (and we tune the power output by neutral-density filter at the beginning of the pump-beam path to stay below the ablation limit).

9gcm−3, and the elasticity of nickel was taken as c11 = 251. p. 4
Where the paper says it

Further details on all three points above — including a pulse-duration analysis and comparisons at lower averaging and coarser angular steps — are given in the Supplementary information. Comparing the Measured and the Calculated With these modifications, the TGS method has been applied to a nickel single crystal and an iron aluminide single crystal (Fe3Al).

9GPa, c12 = 157.7GPa, and c44 = 124.3GPa The Fe3Al samples were cut from an intermetallic alloy (exact composition Fe–28 at. p. 6
Where the paper says it

This approach enables rich information to be obtained on a single cut of the crystal with arbitrary orientation. Moreover, the measurement spot is relatively local in terms of both its in-plane dimensions (∼ 800 × 800 µm2 , can be reduced below ∼ 500 × 500 µm2 without any significant loss of information, as it still comprises several tens of fringes for the used wavelength) and its penetration depth (up to several wavelengths), which can be utilized for example for measurements on individual grains over surfaces of coarse-grained polycrystals, functionally graded materials with gradient composition, or individual components of macroscopic composites.

%Al–4 at.% Cr) manufactured by Bridgman growth at the Institute of Physics, Czech Academy of Sciences The density was ρ = 6. p. 0
Where the paper says it

Ultra-transient grating spectroscopy for visualization of surface acoustics Toma´s Grabec ˇ 1 , Pavla Stoklasova´ 1 , Krist´yna Repcek ˇ 1 , Jakub Kusn´ır ˇ 1,2, David Maresˇ 1 , Martin Sev ˇ c´ık ˇ 1 , Petr Sedlak´ 1 , and Hanus Seiner ˇ 1,* 1 Institute of Thermomechanics, Czech Academy of Science, Dolejskova 1402/5, 182 00 Prague, Czechia ˇ 2Faculty of Nuclear Science and Physical Engineering, Czech Technical University in Prague, Trojanova 13, 120 00 Prague, Czechia *Corresponding author: hseiner@it. Seiner) Abstract – Ultrasonic wave propagation across material surfaces reveals essential information about the materials’ elastic behavior.

62gcm−3, and elasticity c11 = 179. p. 6
Where the paper says it

, by removing the number of fringes) is connected to lowering of the quality factor of the resulting spectrum (a very direct way to meet the Heisenberg principle, that is, that increasing the spatial precision is necessarily connected to lowering the frequency precision). This was presented in detail on the measurements by spatially resolved acoustic spectroscopy (SRAS),50 which was devised to scan SAW velocity across polycrystalline samples to evaluate the microstructure, crystallographic orientations, and, ideally, single-crystalline elasticity.

5GPa, c12 = 119.6GPa, and c44 = 129.9GPa

Transient Grating Spectroscopy

The measurements were performed using the optical path outlined in Figure 1(a), which is a classical arrangement for TGS The pump pattern was created by interference of strongly elliptical laser beams (approximately 0.8 × 0.1 mm2 in cross-section) in the near infrared range (1064 nm, pulse energy 110 µJ, pulse duration 0. p. 1

Where the paper says it

Still, superposition of these displacement fields for a periodic array of sources can lead to a formation of a standing-wave pattern – a very short-lived grating, which we henceforth call the ultra-transient grating, to emphasize that this grating is transient with respect to the transient grating created by standing SAWs. Since the TGS signals are recorded continuously across the loading pulse moment and directly at the location where the pulse is applied, they should also contain information about the early-time, ultra-transient response – albeit small in amplitude and short in duration, and therefore small in frequency spectra.

53 ns (FWHM), repetition rate 1 kHz) The nominal acoustic wavelength in the reported measurements was 10 µm, with the exact wavelength calibrated using a known material – for the reported measurement, the calibrated value was 10. p. 6
Where the paper says it

Moreover, the measurement spot is relatively local in terms of both its in-plane dimensions (∼ 800 × 800 µm2 , can be reduced below ∼ 500 × 500 µm2 without any significant loss of information, as it still comprises several tens of fringes for the used wavelength) and its penetration depth (up to several wavelengths), which can be utilized for example for measurements on individual grains over surfaces of coarse-grained polycrystals, functionally graded materials with gradient composition, or individual components of macroscopic composites. In fact, the three cuts of Fe3Al presented here are a part of a single large polycrystalline piece of this material.

064±0.005µm The pulse energy was lowered in the optical path and tuned to be slightly below the ablation limit of the sample (typically below 40 µJ on the sample surface), so that no visible trace was left after the measurement The heat diffusion length (approximated as L = √αt) was well below the acoustic wavelength (10 µm): around 0. p. 1
Where the paper says it

4–6 The interference pattern acts as an array of line-like thermoacoustic sources (Figure 1(c)) with a harmonic energy perpendicular to the fringes; this direction determines the orientation of the surface k-vector of the acoustic waves generated by the pattern, and can be changed by rotating the sample with respect to the optical path. 7 In the time domain, the TGS source is a short pulse, spanning a broad frequency band from which any chosen frequency can be analyzed separately using spectral methods.

48 µm for Ni, and 0. p. 3
Where the paper says it

The frequency bandwidth of both photodiodes and amplifiers is 1 GHz. To fully utilize this bandwidth, we set the geometry to the acoustic wavelength of λ =10 µm.

18 µm for Fe3Al at 10 ns after the laser pulse

Calculation of the Green’s Function and its Interpretation with respect to the Experiment

The frequency-domain surface dynamics calculation was based on the approach by Every et al., which can be summarized as follows For the given tensor of elastic constants Ci jkl, material density ρ, angular frequency ω, and surface wavevector k∥ = (k1,k2), the Christoffel equation Ci jklk jkl −ρω2 δik Uk = 0 (2) gives six solutions for the out-of-plane component of the wavevector k(n) 3, n = 1,…6, with corresponding eigenvectors U(n) The displacement resulting from a spatially and temporally harmonic surface force Fj (acting in the x j-direction and defining k∥ and ω) is then formed as a superposition of these three phase-matched partial waves u(j)i(k∥,ω; x3) = 3 ∑ A(n)j U(n)i exp(ik (n) 3 x3), (i, j = 1,2,3). (3) The partial-wave amplitudes A(n)j stem from the stress-strain relationship and the free-surface boundary condition as A(n)j = i ω B−1 (n)j, (j,n = 1,2,3). p. 1

Where the paper says it

13 Unlike for the SAWs or pSAWs, the amplitude of the bulk waves therefore diminishes with the propagation, as dictated by the increasing area of the wavefront. At the same time, the stress field carried by the bulk wave often violates the free-surface (plane stress) conditions, which leads to further suppression of their amplitude close to the surface.

(4) where the boundary condition matrix can be written as B(n)l = C3 jklU(n)k k(n)l ω, (l,n = 1,2,3). p. 7
Where the paper says it

After the ultra-transient (early-time) region is cut off (d), the map reduces to peaks indicating the (late-time) resonant response of the surface (See the Supplementary material for details on time-domain signal processing). (e-f) Calculation of the resonant response of the surface using the Ritz–Rayleigh method: (e) the computational domain with boundary conditions; (f) the spectrum of eigenmodes of the domain, color-coded based on the out-of-plane component of the displacement field on the surface – the spectrum perfectly matches the TGS map in (d); (g) modal shapes of the eigenmodes corresponding to the three selected points.

(5) The surface Green’s function components are then obtained as the displacement amplitude at x3 = 0, which reads Gi j(k∥,ω) = 3 ∑ A(n)i U(n)j. p. 0
Where the paper says it

For acoustic experiments on free surfaces of opaque materials, this implies a frequencyresolved description of the material for all directions lying along the surface. 2 The theoretical object representing the response of the surface is the frequency-domain surface elastodynamic Green’s function, which is a function describing the dynamic displacement field arising on a surface of a half-space when loaded by a force that is harmonic both in time and space – a force with prescribed surface wavevector (k-vector) and frequency.

(6) 15

Assessing the quantitative agreement between experiment and calculation

To quantify the agreement between the calculated wavespeeds or features in |G13| plots, and experimental TGS maps, a sequential three-step procedure was used

- In the first step, we compared the TGS map contrasts marking wavespeeds of SAW/pSAW waves and longitudinal waves to the calculated wavespeeds 4

- In the second step, we extracted additional features from the TGS maps that marked wavespeeds of limiting bulk shear waves 4

- In the final step, we compared features from the |G13| plot that were not directly connected to wavespeeds of limiting bulk waves with the experiment 5

Ritz–Rayleigh calculation method

The eigenmodes of the domain representing the free surface were calculated using the Ritz–Rayleigh method for SAWs in an elastically anisotropic half-space The bottom-plane constraint was imposed using a null-space method The resulting eigenvalues represent the square of the frequency ω of the corresponding mode 35

References

The references listed include works on bulk and surface acoustic wave phenomena in crystals, optical heterodyne detection of laser-induced gratings, and determination of all 21 independent elastic coefficients of generally anisotropic solids by resonant ultrasound spectroscopy 7, 35

The authors acknowledge financial support from the Czech Science Foundation and the Operational Programme Johannes Amos Comenius of the Ministry of Education, Youth and Sport of the Czech Republic within the frame of project Ferroic Multifunctionalities (FerrMion) co-funded by the European Union 33

The data supporting these findings have been uploaded to Zenodo repository with the identifier DOI: 10.5281/zenodo.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Enhanced experimental data processing capabilities for Ultra-Transient Grating Spectroscopy (UTGS). The system can perform extensive averaging – up to 50 thousand shots per direction – combined with a fine angular step, which makes otherwise weak features traceable through their continuous directional evolution to reconstruct the frequency-domain Green’s function.

  2. Improved theoretical modeling for anisotropic elastic materials. The system can utilize the partial-wave approach and Ritz–Rayleigh method to calculate displacement fields and compare them directly with experimental TGS maps, as demonstrated by the matching of calculated G13 components with experimental results.

  3. Automated inversion of elastic constants from surface measurements. The AI can implement a sequential three-step procedure to extract wave speeds (SAW/pSAW, limiting bulk shear waves) from TGS maps and compare them against calculated values for inverse determination of elastic constants.

  4. Direct visualization and identification of partial wave conversions. The system can analyze the time-domain signal truncation to identify sharp change in the ultra-transient part of the signal corresponding to conversions between homogeneous and evanescent partial waves, which are responsible for a sharp contrast change in the TGS map.

  5. Multi-condition material characterization capability. The UTGS analysis can be adapted for low and high temperatures, strong magnetic fields, irradiation by leveraging its all-optical contactless nature to observe the frequency-domain |G13| components under these extreme conditions.

Abstract

Ultrasonic wave propagation across material surfaces reveals essential information about the materials' elastic behavior. All direction- and frequency-dependent features of the propagation are encoded in the Green's function. Here we present a direct experimental visualization of the frequency-domain angle-resolved Green's function, including all its complexity resulting from elastic anisotropy. We achieve this visualization using transient grating spectroscopy (TGS), otherwise well established for measuring Rayleigh-type surface acoustic waves (SAWs). But here we focus on early-time thermoacoustic phenomena in the TGS experiment, revealing that, along with the transient standing-wave patterns of SAWs, there also emerge oscillations with at least an order of magnitude shorter lifetimes. These oscillations superpose into dynamic displacement patterns that are transient with respect to the classical transient timescales in TGS; the optical diffraction signal from these ultra-transient gratings enables capturing the surface acoustic response in full detail. By utilizing this feature, ultra-transient grating spectroscopy (UTGS) opens pathways for studying anisotropic materials.

Related papers