Ultra-slow capillary rise on hydrogel surfaces

arXiv:2509.08331 · cond-mat.soft · Submitted 2025-09-10 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Ultra-slow capillary rise on hydrogel surfaces".

Mira: Here's the gist of the paper. Ultra-slow capillary rise on hydrogel surfaces reports that a new model based on fluid transport through porous hydrogel networks successfully describes unusual ultra-slow capillary rise observed on agarose hydrogels The results provide a non-invasive technique to directly estimate the permeability of hydrogel interfaces with high spatial resolution Experimental Setup and Materials The researchers utilized microcapillary rise experiments on agarose++ gels with five different concentrations as well as the 0.5 w/v% agarose gel Microcapillaries were manufactured following the micropipette force sensor protocol, using an inner diameter of 0.75 mm Agarose hydrogels were synthesized in two ways, one with only agarose and MES buffer and another with agarose++, which is used extensively in the plant research community The experimental setup involved an active vibration isolation stage to mount a rectangular piece of the hydrogel on a clean glass coverslip A microcapillary with an aperture radius in the range of R = 16 − 32 µm was held vertically above the gel Modeling and Theoretical Framework The observed ultra-slow capillary rise cannot be described by classical models, leading to the development of a new model based on fluid transport through the hydrogel pores Darcy’s law was used to model the damped flow rate through the porous hydrogel material The volumetric flow rate is given by Q = (kappaAΔp/etaL) Solving this for z by using Darcy’s law together with the capillary pressure as the driving pressure yields z(t) ∼ (gamma cos thetaR squared / η R 2) t ≡ Ut/t This scaling robustly holds over 2 orders of magnitude in time for the observed linear scaling of the capillary rise on hydrogel surfaces Key Findings on Permeability The microcapillary rise technique allows for the measurement of interfacial permeability with non-invasive methods using the equation kappa = Ut ηR squared / 2gamma cos theta The measured interface permeability aligns with the bulk values for the 0.3–0.7% samples, indicating that the interface and bulk permeabilities are the same in this range In contrast, for the stiffest 2% agarose++ sample, the measured fluid flow across the interface is significantly lower than in the bulk This difference highlights that directly probing the interface permeability is important when designing hydrogel interfaces for bioadhesion applications Significance and Future Directions The technique offers a strong improvement over existing methods, such as those based on empirical water content formulas or long drying experiments The spatial resolution achieved is at the length scale of the micropipette tip, which is close to that of single cells The effective pore size of the hydrogel can be deduced from the permeability as rp ∼ kappa 1/2 Future work could focus on improved protocols to perform precise surface tension measurements with, for example, the pendant drop technique The model assumes a rigid network through which the fluid flows, and an extended model considering the poroelasticity of the system would be an interesting future theoretical avenue Data Summary Table Table 1 summarizes the water content and bulk Darcy permeability of the agarose and agarose++ hydrogels used in this work The error for phiw and kappaphiw is the standard deviation from measurements on 4–6 different plates and the propagated error, respectively The results show that the interface permeability aligns with the measured bulk values for the 0.3–0.7% samples The scatter around the solid line in Fig.

Kai: 4 is attributed to inherent variations between different batches used for the microcapillary rise experiments and the water content measurements The largest contribution to the error for Ut in Eq.

Mira: (1) comes from the surface tension measurement The spatial resolution achieved is at the length scale of the micropipette tip (∼ 10−5 m), which is close to that of single cells The technique can be used to probe intricate flow properties of structured hydrogel interfaces, which will be important in future bioadhesion and cell migration studies The interface permeability is a crucial intrinsic material property of hydrogels in the development of these for biomedical applications Microcapillary rise experiments successfully modeled the constant, ultra-slow speed of meniscus rise by implementing Darcy’s law to describe fluid transport through the hydrogel This corresponds to dominating viscous dissipation in the small pores of the hydrogel and represents an interesting capillary phenomenon that can be described with a modified capillary rise model The new microcapillary rise technique can be used to directly measure the interface permeability of hydrogels in a non-invasive manner This is a strong improvement compared to existing techniques, which often render gel compression, are based on an empirical water content formula, or are based on an empirical pore size equation The results probe the bulk permeability Interface permeability is a crucial intrinsic material property of hydrogels in the development of these for biomedical applications This technique allows for interface permeability measurements with spatial resolution down to cellular length scales on such samples The model holds for agarose gels with different pore sizes and different viscosities of the fluid flowing through The effective pore size of the hydrogel can be deduced from the permeability as rp ∼ kappa 1/2 The model assumes a rigid network through which the fluid flows The technique to probe intricate flow properties of structured hydrogel interfaces, which will be important in future bioadhesion and cell migration studies Author Contributions A.D.: investigation, methodology, resources, visualization, writing – review & editing; J.R.: investigation, methodology, resources, writing – review & editing; A.O.T.: investigation; M.B.: conceptualization, formal analysis, funding acquisition, investigation, methodology Conflicts of Interest There are no conflicts to declare Data Availability The datasets used for plotting all graphs in the paper as well as examples of raw data files are shared on Zenodo Acknowledgements This work was funded by the Väisälä project grant RESOLVE by the Finnish Academy of Science Letters (M.B.), the Jane and Aatos Erkko Foundation grant ROOTS (M.B.), as well as Svenska Kulturfonden (M.B.

Paper summary: Kai: Looking at the whole paper, "Ultra-slow capillary rise on hydrogel surfaces," it’s about using a specific physical setup to get a very direct measurement of a material property that used to be much harder to access.

Mira: The authors show that even though the observed capillary rise is ultra-slow and doesn't follow classical models, they can successfully describe it with Darcy's law by modeling fluid transport through porous networks.

Lev: What this means for practical applications is that you can now get a direct estimate of the interface permeability without having to rely on those older empirical water content formulas or just relying on long drying experiments to guess how permeable the gel is.

Kai: The main implication is that this technique gives you spatial resolution down to about ten minus five meters, which is near cellular length scales when looking at these hydrogels.

Mira: And as we discussed, it shows a crucial material property of hydrogels—the interface permeability—and how its value can change depending on the stiffness of the gel structure, like comparing the zero point three to zero point seven percent samples versus that stiffer two percent sample.

Lev: The paper points out a limitation: their model assumes a rigid network for fluid flow, so an extended model considering poroelasticity might be needed to get even more accurate results in complex biological scenarios.

Kai: So, the core message of this work is that you can probe intricate flow properties of structured hydrogel interfaces using microcapillary rise experiments and Darcy's law modeling.

Conclusion: Kai: So we've been looking at this paper about ultra-slow capillary rise on hydrogel surfaces and what they found regarding interface permeability.

Mira: Right, so basically, they used a microcapillary rise experiment and found a way to model that weird slow speed using Darcy's law applied to the porous network inside the hydrogel.

Lev: And the authors are showing you how this setup can give you a direct estimate of that interface permeability without needing those older methods based on empirical water content formulas.

Kai: It’s interesting because it’s not just about getting a number; they found that for their samples, like the zero point three to zero point seven percent ones, the interface and bulk permeabilities actually line up with each other.

Mira: But they also pointed out a difference in that stiffer two percent agarose plus plus sample where the flow across the interface was significantly lower than in the bulk material.

Lev: That difference matters for real hardware; if you were trying to design something for bioadhesion, knowing that interface is different from bulk is crucial information.

Kai: The technique itself offers better spatial resolution than what we usually get, which is down to about ten minus five meters, almost cellular scale.

Mira: And they derived an effective pore size from the permeability measurement itself, which gives you a way to deduce that pore size using the square root of the permeability number.

Lev: The authors say their model assumes a rigid network for fluid flow, so if you're building something complex, you might need to consider how poroelasticity would change those assumptions.

Kai: So, this paper really puts us in a position where we can probe the intricate flow properties of structured hydrogel interfaces with much more detail.

Mira: It’s a strong result for understanding these material properties in the context of biomedical applications, and it opens up new ways to measure them non-invasively.

Anagha Datar, Joonas Ryssy, Aku O. Toivonen, Matilda Backholm

Aalto University

cond-mat.soft

Submitted: 2025-09-10

Updated: 2026-07-08

Journal ref: Soft Matter 22, 4940-4947 (2026)

DOI: 10.1039/D6SM00056H

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 85/100

The gist: Ultra-slow capillary rise on hydrogel surfaces reports that a new model based on fluid transport through porous hydrogel networks successfully describes unusual ultra-slow capillary rise observed on…

Key concepts

Ultra-slow capillary rise
This refers to a very slow movement of the fluid meniscus on the surface of the hydrogel. Classical models fail to explain this behavior, necessitating a new model based on how fluid moves through tiny pores in the material.
Darcy’s Law
This law is used to model how fluid flows slowly through porous materials like hydrogels. It relates the flow rate of the fluid to the pressure difference and the properties of the material, helping researchers calculate transport within these structures.
Interface Permeability (κ)
This measures how easily fluid can pass across a boundary or interface within a hydrogel. The study shows this can be directly measured using microcapillary rise, offering a precise way to understand material properties important for cell adhesion.

Terminology

Summary

Ultra-slow capillary rise on hydrogel surfaces reports that a new model based on fluid transport through porous hydrogel networks successfully describes unusual ultra-slow capillary rise observed on agarose hydrogels The results provide a non-invasive technique to directly estimate the permeability of hydrogel interfaces with high spatial resolution

Experimental Setup and Materials

The researchers utilized microcapillary rise experiments on agarose++ gels with five different concentrations as well as the 0.5 w/v% agarose gel Microcapillaries were manufactured following the micropipette force sensor protocol, using an inner diameter of 0. p. 1

Where the paper says it

1 Microcapillary manufacturing We followed the micropipette force sensor protocol44 when manufacturing the microcapillaries. The microcapillaries were pulled out of 1 mm thick glass capillaries with an inner diameter of 0.

75 mm Agarose hydrogels were synthesized in two ways, one with only agarose and MES buffer and another with agarose++, which is used extensively in the plant research community The experimental setup involved an active vibration isolation stage to mount a rectangular piece of the hydrogel on a clean glass coverslip A microcapillary with an aperture radius in the range of R = 16 − 32 µm was held vertically above the gel

Modeling and Theoretical Framework

The observed ultra-slow capillary rise cannot be described by classical models, leading to the development of a new model based on fluid transport through the hydrogel pores Darcy’s law was used to model the damped flow rate through the porous hydrogel material The volumetric flow rate is given by Q = (kappaAΔp/etaL) Solving this for z by using Darcy’s law together with the capillary pressure as the driving pressure yields z(t) ∼ (gamma cos thetaR squared / η R 2) t ≡ Ut/t This scaling robustly holds over 2 orders of magnitude in time for the observed linear scaling of the capillary rise on hydrogel surfaces

Key Findings on Permeability

The microcapillary rise technique allows for the measurement of interfacial permeability with non-invasive methods using the equation kappa = Ut ηR squared / 2gamma cos theta The measured interface permeability aligns with the bulk values for the 0.3–0.7% samples, indicating that the interface and bulk permeabilities are the same in this range In contrast, for the stiffest 2% agarose++ sample, the measured fluid flow across the interface is significantly lower than in the bulk This difference highlights that directly probing the interface permeability is important when designing hydrogel interfaces for bioadhesion applications

Significance and Future Directions

The technique offers a strong improvement over existing methods, such as those based on empirical water content formulas or long drying experiments The spatial resolution achieved is at the length scale of the micropipette tip, which is close to that of single cells The effective pore size of the hydrogel can be deduced from the permeability as rp ∼ kappa 1/2 Future work could focus on improved protocols to perform precise surface tension measurements with, for example, the pendant drop technique The model assumes a rigid network through which the fluid flows, and an extended model considering the poroelasticity of the system would be an interesting future theoretical avenue

Data Summary Table

Table 1 summarizes the water content and bulk Darcy permeability of the agarose and agarose++ hydrogels used in this work The error for phiw and kappaphiw is the standard deviation from measurements on 4–6 different plates and the propagated error, respectively The results show that the interface permeability aligns with the measured bulk values for the 0.3–0.7% samples The scatter around the solid line in Fig. p. 4

Where the paper says it

7% samples. The scatter around the solid line in Fig.

4 is attributed to inherent variations between different batches used for the microcapillary rise experiments and the water content measurements The largest contribution to the error for Ut in Eq. p. 4
Where the paper says it

The scatter around the solid line in Fig. 4 is attributed to inherent variations between different batches used for the microcapillary rise experiments and the water content measurements.

(1) comes from the surface tension measurement The spatial resolution achieved is at the length scale of the micropipette tip (∼ 10−5 m), which is close to that of single cells The technique can be used to probe intricate flow properties of structured hydrogel interfaces, which will be important in future bioadhesion and cell migration studies The interface permeability is a crucial intrinsic material property of hydrogels in the development of these for biomedical applications

Conclusions

Microcapillary rise experiments successfully modeled the constant, ultra-slow speed of meniscus rise by implementing Darcy’s law to describe fluid transport through the hydrogel This corresponds to dominating viscous dissipation in the small pores of the hydrogel and represents an interesting capillary phenomenon that can be described with a modified capillary rise model The new microcapillary rise technique can be used to directly measure the interface permeability of hydrogels in a non-invasive manner This is a strong improvement compared to existing techniques, which often render gel compression, are based on an empirical water content formula, or are based on an empirical pore size equation The results probe the bulk permeability Interface permeability is a crucial intrinsic material property of hydrogels in the development of these for biomedical applications This technique allows for interface permeability measurements with spatial resolution down to cellular length scales on such samples The model holds for agarose gels with different pore sizes and different viscosities of the fluid flowing through The effective pore size of the hydrogel can be deduced from the permeability as rp ∼ kappa 1/2 The model assumes a rigid network through which the fluid flows The technique to probe intricate flow properties of structured hydrogel interfaces, which will be important in future bioadhesion and cell migration studies

Author Contributions

A.D.: investigation, methodology, resources, visualization, writing – review & editing; J. p. 5

Where the paper says it

Author contributions A. : investigation, methodology, resources, visualization, writing – review & editing; J.

R.: investigation, methodology, resources, writing – review & editing; A. p. 5
Where the paper says it

Author contributions A. : investigation, methodology, resources, visualization, writing – review & editing; J.

O.T.: investigation; M. p. 5
Where the paper says it

Author contributions A. : investigation, methodology, resources, visualization, writing – review & editing; J.

B.: conceptualization, formal analysis, funding acquisition, investigation, methodology

Conflicts of Interest

There are no conflicts to declare

Data Availability

The datasets used for plotting all graphs in the paper as well as examples of raw data files are shared on Zenodo

Acknowledgements

This work was funded by the Väisälä project grant RESOLVE by the Finnish Academy of Science Letters (M.B.), the Jane and Aatos Erkko Foundation grant ROOTS (M. p. 5

Where the paper says it

Acknowledgements This work was funded by the Väisälä project grant RESOLVE by the Finnish Academy of Science Letters (M. ), the Jane and Aatos Erkko Foundation grant ROOTS (M.

B.), as well as Svenska Kulturfonden (M. p. 5
Where the paper says it

), the Jane and Aatos Erkko Foundation grant ROOTS (M. ), as well as Svenska Kulturfonden (M.

B.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Enhanced permeability estimation for hydrogel interfaces by implementing a non-invasive microcapillary rise technique that directly estimates interfacial permeability using Darcy’s law derived model: Q = (κA/ηL)Δp, which provides high spatial resolution measurement down to cellular length scales.

  2. Ability to directly estimate the interface permeability of hydrogels in a non-invasive manner, which is a strong improvement compared to existing techniques that often render gel compression or rely on empirical water content formulas and long drying experiments.

  3. Capability to probe the actual difference between interface and bulk permeabilities, as shown by finding that the interface permeability aligns with the measured bulk values for the 0.3–0.7% samples, highlighting its importance for designing hydrogel interfaces in applications like bioadhesion.

  4. Prediction of fluid flow transport through porous hydrogel networks using a modified capillary rise model: z(t) ∼ (κγ cos θ / ηR2) t, allowing for the modeling of ultra-slow capillary rise dynamics governed by viscous dissipation within the small pores rather than inside the glass capillary.

  5. Deduction of effective pore size from measured permeability using the relationship rp ∼ κ1/2, enabling a non-invasive estimation of the hydrogel interface mesh size at a spatial resolution close to single cells.

Abstract

Capillary rise occurs when a thin tube contacts a liquid, which rises against gravity due to the capillary force. This phenomenon is present in a wide range of everyday and industrial settings and provides the means to measure the physical properties of liquids. Here, we report on the unusual ultra-slow capillary rise on a solid-like material of agarose hydrogels. The observed meniscus motion cannot be described with classical capillary rise models, and we develop a new model based on the fluid transport through the porous hydrogel network. Our model is in good agreement with the temporal scaling observed in our experiments with agarose gels made with five different concentrations and with two different viscosities of the liquid flowing inside the gel. Our results provide a non-invasive technique to directly estimate the permeability of hydrogel interfaces with high spatial resolution, which is important in the implementation of hydrogels in advanced biomedical applications.

Related papers