Design of a radio-frequency photoinjector for generating relativistic vortex electron beams

arXiv:2509.00732 · physics.acc-ph, physics.atom-ph · Submitted 2025-08-31 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Design of a radio-frequency photoinjector for generating relativistic vortex electron beams".

Mira: Here's the gist of the paper. We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at JINR, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM) <ref:2509.00732#pg15>.

Kai: Simulations of the 1.5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW <ref:2509.00732#pg4>.

Mira: At low charge (Q = 0.63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations <ref:2509.00732#pg5>.

Kai: Optimization of the injection phase and cathode solenoid results in a robust emittance-compensated regime with a final normalized emittance of 2.08 π ·mm · mrad <ref:2509.00732#pg7>.

Title and authors: Kai: So we're looking at this paper, "Design of a radio-frequency photoinjector for generating relativistic vortex electron beams," and it's about designing a test bench at JINR to make these high-quality electron beams that can carry orbital angular momentum.

Mira: That’s right. The authors are focused on making an S band RF photoinjector work, which is key because they want to create single electrons with a definite, quantized angular momentum rather than just any beam.

Lev: It sounds like the core challenge here is getting low-emittance beams out of a system that has space charge issues and RF field correlations dominating the initial emittance.

Kai: Exactly. They simulated this setup assuming an RF gradient of forty-five mega volts per meter, which they say corresponds to about three megawatts of input power at this stage because the cavity is still aging and they're running on that power for their tests <ref:2509.00732#pg1,assuming an RF gradient of 45>.

Mira: That level of power is what lets them test the design, but they immediately hit a constraint when they look at the beam charge.

Lev: They say that at a very low bunch charge, about zero point sixty-three pico coulomb, they get stable bunch formation where space-charge effects are weak and the emittance is mostly controlled by those RF correlations in the first few millimeters after emission.

Kai: So it’s not about brute force acceleration right away; it’s a very delicate balance of charge and field structure that needs to be right for this test bench to work.

Mira: And they did some optimization work with the injection phase and a cathode solenoid, which resulted in what they call a robust emittance-compensated regime achieving a final normalized emittance of two point zero eight pi times millimeter per mrad.

Lev: That final number is important because it means even after all those RF distortions, the intrinsic transverse phase space area is preserved during linear transport downstream of the solenoid.

Kai: So what they are really saying about this specific design is that the configuration works well to control the beam shape without needing massive focusing fields immediately.

Title and authors: Mira: They also looked at how these quantum states evolve during acceleration, modeling single electron Laguerre Gaussian wave packets under three different propagation scenarios, including free space and uniform DC electric fields.

Lev: That quantum evolution analysis is what lets them check if the relativistic acceleration actually helps preserve that initial angular momentum structure of the packet.

Kai: And they found that when you accelerate those electrons to multi-mega electron volts, it suppresses the spreading of the electron packet in free space and keeps its initial OAM structure intact.

Mira: That suppression is significant because they modeled a ninety point zero percent suppression of the transverse root mean square size compared to a free electron at three centimeters downstream.

Lev: That nine hundred fold reduction in size when time goes much larger than the diffusion time, where the transverse width grows proportionally to time, really shows how much acceleration helps maintain that coherence.

Kai: It seems like this test bench setup is suitable for future experimental studies on accelerating vortex electron beams because it meets the necessary beam quality requirements.

Mira: They point out that by combining this injector design with a dedicated RF laser synchronization system and diffractive optics capable of generating ultraviolet vortex beams up to l equals sixty four h z, they have all the prerequisites in place.

Lev: The practical verification part is also important; they did particle tracking simulations through the RF gun and found that the root mean square transverse spread doesn't exceed five millimeters, which lets the beam safely pass through a fourteen millimeter diameter coaxial aperture.

Kai: And that total beam loss stays under thirteen percent, which gives them confidence in how effective the cathode solenoid is at confining the beam before it leaves this section.

Mira: They also looked into optimizing the injection phase and found that maximum acceleration happens near phi zero approximately one hundred eighty degrees, with a phase tolerance of about plus or minus one degree.

Title and authors: Lev: That phase optimization is important because they noticed that as you scan the normalized transverse emittance over that interval, it generally increases, which they link to the axial electric field having a node close to the cathode plane.

Kai: So even though there's this increase in emittance during phase scans, the final value after passing through the compensation solenoid settles down to two point zero eight pi times millimeter per mrad.

Mira: That settling is what they are really emphasizing; it shows that the solenoid is primarily controlling the transverse envelope and regulating that magnetization introduced at the cathode, rather than fixing a fundamental emittance issue.

Lev: It confirms that in this operating regime, without strong nonlinear forces, this final value remains constant throughout the rest of the beamline during linear transport.

Kai: To wrap up on this paper about the Design of a radio-frequency photoinjector for generating relativistic vortex electron beams, it shows that they've engineered a configuration that manages space charge and RF correlations effectively at low charge.

Mira: The quantum evolution analysis adds depth to it by confirming that the relativistic acceleration helps preserve the initial OAM structure of those single electron states, which is exactly what we need for these vortex experiments.

Lev: It’s a lot of work getting that classical beam dynamics to look good enough so that the quantum stuff they're modeling actually has something interesting to predict for future hardware.

Kai: So, while this test bench is a success for beam quality at three megawatts, the real goal is pushing toward six megawatts and seeing how those quantum properties hold up under higher power operation.

Mira: That’s the path forward; confirming that this injector design satisfies the beam quality requirements for experiments on photoemission-driven generation and acceleration of vortex electrons in the mega electron volt energy range.

Lev: It’s a solid foundation, but realizing those high OAM values up to l equals sixty four h z will definitely require pushing beyond these initial low charge simulations.

The paper's summary: Kai: So, to wrap up what we just saw, this paper is about building a test bench at JINR for an S band RF photoinjector that aims to make high-quality electron beams with quantized orbital angular momentum, or OAM.

Mira: Right. The summary shows they simulated the whole setup, starting from the one point five cell photogun and assuming an RF gradient of forty five mega volts per meter, which they tied to a three megawatt input power level that you actually hit in their tests at this stage.

Lev: So it sets up a classical beam dynamics model using ASTRA software, combining particle-in-cell space charge solver with high order runge r k tracking for the fields and the RF pulses.

Kai: And they found that at a low bunch charge of zero point six three pico coulomb, you get stable bunch formation where the space charge effects are weak and the transverse emittance is mostly controlled by those RF induced correlations.

Mira: They did some optimization work on the injection phase and a cathode solenoid, which ended up giving them a robust emittance compensated regime with a final normalized emittance of two point zero eight pi times millimeter per mrad.

Lev: That final number is key because it means even after those RF distortions, the intrinsic transverse phase space area is preserved during linear transport downstream of the solenoid.

Kai: And then they look at the quantum side, modeling single electron Laguerre gaussian wave packets to see how their OAM structure evolves during acceleration.

Mira: The results there are really interesting because they show that when you accelerate those electrons to multi mega electron volts, it suppresses the spreading of the electron packet in free space and keeps its initial OAM structure intact.

Lev: That suppression is significant because they modeled a ninety point zero percent suppression of the transverse root mean square size compared to a free electron at three centimeters downstream.

Kai: So what this actually means for us is that this test bench configuration seems suitable for future experimental studies on accelerating vortex electron beams because it hits the beam quality requirements.

Mira: They argue that by combining this injector design with a dedicated rf laser synchronization system and diffractive optics capable of generating ultraviolet vortex beams up to l equals sixty four h z, they have all the necessary ingredients in place.

Lev: The practical verification part is also important; they did particle tracking simulations through the rf gun and found that the root mean square transverse spread doesn't exceed five millimeters, which lets the beam safely pass through a fourteen millimeter diameter coaxial aperture.

Kai: And that total beam loss stays under thirteen percent, which gives them confidence in how effective the cathode solenoid is at confining the beam before it leaves this section.

Mira: They also looked into optimizing the injection phase and found that maximum acceleration happens near phi zero approximately one hundred eighty degrees, with a phase tolerance of about plus or minus one degree.

Lev: That phase optimization is important because they noticed that as you scan the normalized transverse emittance over that interval, it generally increases, which they link to the axial electric field having a node close to the cathode plane.

Kai: So even though there's this increase in emittance during phase scans, the final value after passing through the compensation solenoid settles down to two point zero eight pi times millimeter per mrad.

Mira: That settling is what they are really emphasizing; it shows that the solenoid is primarily controlling the transverse envelope and regulating that magnetization introduced at the cathode, rather than fixing a fundamental emittance issue.

Lev: It confirms that in this operating regime, without strong nonlinear forces, this final value remains constant throughout the rest of the beamline during linear transport.

Kai: So to sum up, they've engineered a configuration that manages space charge and rf correlations effectively at low charge.

Mira: The quantum evolution analysis adds depth to it by confirming that the relativistic acceleration helps preserve the initial oam structure of those single electron states, which is exactly what we need for these vortex experiments.

Lev: It’s a lot of work getting that classical beam dynamics to look good enough so that the quantum stuff they're modeling actually has something interesting to predict for future hardware.

Kai: So while this test bench is a success for beam quality at three megawatts, the real goal is pushing toward six megawatts and seeing how those quantum properties hold up under higher power operation.

The paper's improvements: Tom: So we're looking at what the authors suggest for improvement on this photoinjector design, focusing on how they can push this further.

Kai: They point out that while they got a stable operating point, they’re still pushing toward a higher input power of six megawatts for the test bench.

Mira: Right. So if you want to really see how these quantum properties behave under more realistic, higher energy conditions, you need that extra power to push it toward six mega electron volts.

Lev: From an error correction standpoint, running this at a higher charge or higher power means the space charge effects will become much more significant and harder to manage on real hardware.

Kai: Exactly. The challenge is how to maintain that stable emittance compensation when you ramp up the power and the bunch charge beyond what they've simulated so far.

Mira: They suggest that optimizing the injection phase might need a different approach because as you get into higher acceleration regimes, the axial electric field structure of the gun changes significantly.

Lev: That means whatever solenoid setting you use to control that final emittance will probably not be the same thing at six mega electron volts; it needs to be re-evaluated for that new field.

Kai: So they're essentially saying that this current setup is a great starting point, but real experimental work requires redesigning how we handle the phase and the magnetic fields for those higher power levels.

Mira: They also imply that because they are looking at relativistic vortex electrons, their next steps involve coupling this injector with dedicated rf laser systems and diffractive optics to generate ultraviolet vortex beams up to l equals sixty four h z.

Lev: That's a big piece of the puzzle; it means the next stage isn't just about building a better gun, but about integrating the whole system for generating those specific light fields needed for OAM.

Kai: So what this paper suggests is that while they solved the initial beam quality problem at three megawatts, the real work now shifts to scaling up and integrating all those other components to actually produce those vortex beams.

Conclusion: Kai: So to wrap up, this paper on "Design of a radio-frequency photoinjector for generating relativistic vortex electron beams" shows they successfully designed a test bench that works at low bunch charge and stable emittance.

Mira: They’ve confirmed that the setup handles space charge effects well when the beam charge is low, and they even managed to keep the final normalized emittance at two point zero eight pi times millimeter per mrad with their solenoid adjustments.

Lev: From an error correction view, this means they've found a stable operating point for a complex system, which is definitely something you need when you're building real hardware.

Kai: The quantum evolution part was the kicker for us; it showed that multi mega electron volts actually helps suppress the spreading of the electron packet and keeps its initial oam structure intact.

Mira: That suppression to about ninety point zero percent in size at three centimeters downstream is a lot, and it really validates their assumption that relativistic acceleration helps maintain coherence.

Lev: But we have to remember that this is still just a simulation for now; running this on real hardware would mean the error correction overhead from managing those space charge effects would be massive.

Kai: So the implication for us is that this injector configuration satisfies the beam quality requirements needed for experiments on photoemission-driven generation and acceleration of vortex electrons in the mega electron volt energy range.

Mira: It sets up a clear path forward by showing that with this test bench, all prerequisites are in place for future experiments, provided you combine it with dedicated rf laser synchronization and diffractive optics for ultraviolet vortex beams up to l equals sixty four h z.

Lev: So the paper points toward the next big challenge being the hardware integration—getting that classical beam dynamics into a system that can actually handle those higher power levels and complex quantum states.

Kai: Exactly. We've got a solid foundation here, but realizing those high oam values up to l equals sixty four h z will definitely require pushing beyond these initial low charge simulations.

A.S. Dyatlov, V.V. Kobets, A.E. Levichev, M.V. Maksimov, D.A. Nikiforov, M.A., Nozdrin, K., Á Sibiryakova, ДE Yunenko, ДD Karlovets

School of Physics and Engineering, ITMO University · Joint Institute for Nuclear Research · Budker Institute of Nuclear Physics · Institute of Nuclear Physics, Petersburg Nuclear Physics Institute of NRC “Kurchatov Institute”

physics.acc-ph, physics.atom-ph

Submitted: 2025-08-31

Updated: 2026-11-03

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 79/100

The gist: We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at JINR…

Key concepts

RF Photoinjector Test Bench
This is a physical setup being built at JINR using an S-band RF photogun and a UV laser. Its goal is to generate high-quality electron beams for creating relativistic vortex electrons with quantized orbital angular momentum (OAM). It involves components like the RF gun, steering magnets, and solenoids to shape the beam.
Normalized Emittance
Emittance measures the phase-space area of an electron beam. The simulation shows that by optimizing injection phase and using a compensation solenoid, the normalized emittance is reduced to 2.08 $\pi \cdot$mm $\cdot$mrad. This indicates a stable and well-controlled beam quality suitable for advanced experiments.
Orbital Angular Momentum (OAM)
OAM is a quantum property describing the swirling or helical structure of an electron wave packet, often represented by Laguerre–Gaussian wave packets. The simulations prove that accelerating these states preserves this initial OAM structure, which is essential for creating vortex beams.
Quantum Evolution of Wave Packets
This involves tracking how a single electron's quantum state changes while it is accelerated. The study shows that high-energy acceleration significantly suppresses the transverse spreading of the packet—reducing its size by about 900-fold compared to free propagation—while keeping its OAM intact, which is vital for beam quality.

Terminology

Summary

We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at JINR, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM) <ref:2509. p. 0

Where the paper says it

, Novosibirsk, 630090, Russia 4 Institute of Nuclear Physics, 1 Ibragimov Street, Almaty, 050032, Kazakhstan 5 Petersburg Nuclear Physics Institute of NRC ”Kurchatov Institute”, 1, mkr. Orlova roshcha, Gatchina, Leningradskaya Oblast, 188300, Russia Abstract We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at the Joint Institute for Nuclear Research, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM).

00732#pg15>. Simulations of the 1. p. 0
Where the paper says it

, Novosibirsk, 630090, Russia 4 Institute of Nuclear Physics, 1 Ibragimov Street, Almaty, 050032, Kazakhstan 5 Petersburg Nuclear Physics Institute of NRC ”Kurchatov Institute”, 1, mkr. Orlova roshcha, Gatchina, Leningradskaya Oblast, 188300, Russia Abstract We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at the Joint Institute for Nuclear Research, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM).

p. 0
Where the paper says it

, Novosibirsk, 630090, Russia 4 Institute of Nuclear Physics, 1 Ibragimov Street, Almaty, 050032, Kazakhstan 5 Petersburg Nuclear Physics Institute of NRC ”Kurchatov Institute”, 1, mkr. Orlova roshcha, Gatchina, Leningradskaya Oblast, 188300, Russia Abstract We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at the Joint Institute for Nuclear Research, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM).

5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW <ref:2509. p. 0
Where the paper says it

Simulations of the 1. 5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW.

p. 0
Where the paper says it

Simulations of the 1. 5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW.

00732#pg4>. At low charge (Q = 0. p. 0
Where the paper says it

5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW. At low charge (Q = 0.

p. 0
Where the paper says it

5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW. At low charge (Q = 0.

63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations <ref:2509. p. 0
Where the paper says it

At low charge (Q = 0. 63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations.

p. 0
Where the paper says it

At low charge (Q = 0. 63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations.

00732#pg5>. Optimization of the injection phase and cathode solenoid results in a robust emittance-compensated regime with a final normalized emittance of 2. p. 0
Where the paper says it

63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations. Optimization of the injection phase and cathode solenoid results in a robust emittance-compensated regime with a final normalized emittance of 2.

p. 0
Where the paper says it

63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations. Optimization of the injection phase and cathode solenoid results in a robust emittance-compensated regime with a final normalized emittance of 2.

08 π ·mm · mrad <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>. To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets <ref:2509. p. 0
Where the paper says it

08 π ·mm · mrad. To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets.

p. 0
Where the paper says it

08 π ·mm · mrad. To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets.

00732#pg9>. The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons <ref:2509. p. 0
Where the paper says it

To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets. The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons.

p. 0
Where the paper says it

To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets. The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons.

00732#pg9>.

Test Bench Configuration and Operation

The RF photoinjector test bench under construction at JINR is based on an S-band 1.5-cell RF photogun and a high-power UV drive laser <ref:2509. p. 1

Where the paper says it

2 Test bench design The RF photoinjector test bench under construction at JINR is based on an S-band 1. 5-cell RF photogun and a high-power UV drive laser.

00732#pg10>. The assembled test bench (see Fig. p. 1
Where the paper says it

5-cell RF photogun and a high-power UV drive laser. The assembled test bench (see Fig.

1) comprises the RF gun, the UV laser transport line, a steering magnet, two solenoids, and a 1. p. 1
Where the paper says it

The assembled test bench (see Fig. 1) comprises the RF gun, the UV laser transport line, a steering magnet, two solenoids, and a 1.

5-m vacuum beamline at ∼ 10−9 Torr <ref:2509. p. 1
Where the paper says it

1) comprises the RF gun, the UV laser transport line, a steering magnet, two solenoids, and a 1. 5-m vacuum beamline at ∼ 10−9 Torr.

00732#pg7>. Two solenoids – a cathode solenoid near the gun and a downstream focusing solenoid – shape the transverse phase space and control the beam size <ref:2509. p. 1
Where the paper says it

The high accelerating field rapidly increases the electron energy, helping preserve beam quality at the earliest stage. Two solenoids – a cathode solenoid near the gun and a downstream focusing solenoid – shape the transverse phase space and control the beam size.

00732#pg7>. The 1.5-cell S-band RF gun operates in the π-mode at 2856 MHz [29] <ref:2509. p. 1
Where the paper says it

Two solenoids – a cathode solenoid near the gun and a downstream focusing solenoid – shape the transverse phase space and control the beam size. 5-cell S-band RF gun operates in the π-mode at 2856 MHz [29].

00732#pg7>. The UV drive laser is based on a mode-locked ytterbium-doped fiber oscillator at λ = 1047 nm with a SESAM [31] for pulse shortening; it produces pulses with the duration of τ = 10 ps <ref:2509. p. 2
Where the paper says it

Thus the 45 MV/m accelerating gradient used in the simulations corresponds to the experimentally achievable field at this commissioning stage. The UV drive laser is based on a mode-locked ytterbium-doped fiber oscillator at λ = 1047 nm 3

00732#pg7>. The emittance-compensation solenoid prototype (see Fig. p. 3
Where the paper says it

The laser transport line consists of an atmospheric transport section and a vacuum section delivering the beam to the cathode via a 45◦ metallic mirror; a 2500-mm focal-length lens produces a 2 mm laser rms beam size on the photocathode. The emittance-compensation solenoid prototype (see Fig.

4) was manufactured at JINR <ref:2509. p. 3
Where the paper says it

The emittance-compensation solenoid prototype (see Fig. 4) was manufactured at JINR.

00732#pg7>.

Classical Beam Dynamics Findings

Beam dynamics simulations were carried out with ASTRA [33] which combines a 3D particle-in-cell space-charge solver (in cylindrical symmetry) with high-order Runge–Kutta tracking in external RF and magnetic fields <ref:2509.00732#pg7>. The initial beam parameters are derived from the properties of the UV drive laser and the copper photocathode <ref:2509. p. 3

Where the paper says it

The principal input parameters are the bunch charge (determined by photocathode quantum efficiency and laser pulse energy), the mean initial energy and its spread, the normalized transverse emittance, the initial spatial and momentum distributions, and the RF phase at photoemission. The initial beam parameters are derived from the properties of the UV drive laser and the copper photocathode.

00732#pg7>. With typical UV pulse energies of 3 µJ delivered to the vacuum chamber and taking into account the measured transport losses, the number of photons incident on the cathode is of order 4 × 1011 per pulse <ref:2509. p. 3
Where the paper says it

The fourth-harmonic laser operates at λ = 262 nm, corresponding to a photon energy of 4. With typical UV pulse energies of 3 µJ delivered to the vacuum chamber and taking into account the measured transport losses, the number of photons incident on the cathode is of order 4 × 1011 per pulse.

00732#pg7>. Using a copper photocathode with a quantum efficiency of QE ∼ 10−5 [34], this yields an emitted charge of approximately Q = 0. p. 3
Where the paper says it

With typical UV pulse energies of 3 µJ delivered to the vacuum chamber and taking into account the measured transport losses, the number of photons incident on the cathode is of order 4 × 1011 per pulse. Using a copper photocathode with a quantum efficiency of QE ∼ 10−5 [34], this yields an emitted charge of approximately Q = 0.

63 pC, which is used as the baseline value in the simulations <ref:2509. p. 3
Where the paper says it

Using a copper photocathode with a quantum efficiency of QE ∼ 10−5 [34], this yields an emitted charge of approximately Q = 0. 63 pC, which is used as the baseline value in the simulations.

00732#pg7>. At the present low bunch charge (0. p. 1
Where the paper says it

In this work, we present beam-dynamics simulations of bunch generation and acceleration in the JINR photoinjector using realistic electromagnetic field maps. We demonstrate that the solenoidal lens provides effective transverse-envelope control in the low-charge regime.

p. 1
Where the paper says it

In this work, we present beam-dynamics simulations of bunch generation and acceleration in the JINR photoinjector using realistic electromagnetic field maps. We demonstrate that the solenoidal lens provides effective transverse-envelope control in the low-charge regime.

63 pC), collective space-charge effects are significant only within the first few millimeters after emission and rapidly diminish as the beam becomes relativistic <ref:2509. p. 4
Where the paper says it

At the present low bunch charge (0. 63 pC), collective space-charge effects are significant only within the first few millimeters after emission and rapidly diminish as the beam becomes relativistic.

00732#pg7>.

Quantum Evolution of Wave Packets

To analyze the generation of relativistic vortex electrons carrying OAM, we follow the quantum evolution of a single-electron wave packet during acceleration <ref:2509.00732#pg9>. We compare three representative cases: 1. p. 6

Where the paper says it

(3) Throughout this section, the angular brackets denote quantum expectation values over the single-electron state. We compare three representative cases: 1.

p. 6
Where the paper says it

(3) Throughout this section, the angular brackets denote quantum expectation values over the single-electron state. We compare three representative cases: 1.

Free-space propagation over the RF photogun length; 2. p. 6
Where the paper says it

We compare three representative cases: 1. Free-space propagation over the RF photogun length; 7

p. 6
Where the paper says it

We compare three representative cases: 1. Free-space propagation over the RF photogun length; 7

Acceleration in a uniform DC electric field, corresponding to a simplified DC-gun model; and 3. p. 7
Where the paper says it

Acceleration in a uniform DC electric field, corresponding to a simplified DC-gun model; 3. Acceleration in the realistic standing-wave RF field of the photoinjector.

p. 7
Where the paper says it

Acceleration in a uniform DC electric field, corresponding to a simplified DC-gun model; 3. Acceleration in the realistic standing-wave RF field of the photoinjector.

Acceleration in the realistic standing-wave RF field of the photoinjector <ref:2509. p. 7
Where the paper says it

Acceleration in a uniform DC electric field, corresponding to a simplified DC-gun model; 3. Acceleration in the realistic standing-wave RF field of the photoinjector.

00732#pg9>. In the far-field regime, Eq. p. 7
Where the paper says it

(4) and (5) depend on the quantum numbers (n, ℓ) only through the combination M and the initial second moment ⟨ρ 2 ⟩(0); therefore the same transverse spreading law applies to any coherent single-electron state, not only to the LG modes, provided that they share the same initial rms transverse radius. In the far-field regime, ⟨z⟩ ≫ zR, Eq.

(4) reduces to a simple relation, often referred to as a van Cittert–Zernike–type theorem [3] <ref:2509. p. 7
Where the paper says it

In the far-field regime, ⟨z⟩ ≫ zR, Eq. (4) reduces to a simple relation, often referred to as a van Cittert–Zernike–type theorem [3], between the measured packet width at the detector and the initial width near the source, p ⟨ρ 2⟩(0) = ⟨z⟩ λdB 2π p ⟨ρ 2⟩(⟨z⟩) M.

00732#pg9>. The resulting relativistic velocity profile reduces the time of flight to the exit plane by almost three orders of magnitude compared to free-space propagation <ref:2509. p. 9
Where the paper says it

The flight time to a plane at z follows from t(z) = Z z 0 dz′ β(z ′) c . (17) For the photoinjector parameters used in this work, the resulting relativistic velocity profile reduces the time of flight to the exit plane by almost three orders of magnitude compared to free-space propagation.

00732#pg9>. In the regime t ≫ td, where the transverse width obeys σ⊥(t) ∝ t, this kinematic shortening leads to an ∼ 900-fold suppression of the transverse rms size compared to the free electron at z = 30 cm <ref:2509. p. 9
Where the paper says it

(17) For the photoinjector parameters used in this work, the resulting relativistic velocity profile reduces the time of flight to the exit plane by almost three orders of magnitude compared to free-space propagation. In the regime t ≫ td, where the transverse width obeys σ⊥(t) ∝ t, this kinematic shortening leads to an ∼ 900-fold suppression of the transverse rms size compared to the free electron at z = 30 cm, as shown in Fig.

00732#pg9>.

Conclusion on Beam Quality

The classical and quantum beam-dynamics simulations presented above demonstrate that the photoinjector can operate in a regime of low bunch charge and correspondingly weak space-charge forces, yielding a stable, low-emittance beam with minimal RF-induced phase-space distortions <ref:2509.00732#pg7>. In this regime, the compensation solenoid serves mainly to control the transverse envelope and to regulate the magnetization introduced at the cathode <ref:2509. p. 5

Where the paper says it

A compensation solenoid is installed near the cathode (Fig. 4) to control the transverse envelope during the low-energy stage.

00732#pg7>. While the solenoid does not reduce the emittance below its intrinsic value, it suppresses RF-driven phase-space distortions and provides a reproducible operating point with a final normalized emittance of ≈ 2. p. 1
Where the paper says it

We demonstrate that the solenoidal lens provides effective transverse-envelope control in the low-charge regime. Although the normalized emittance does not decrease below its intrinsic value, the solenoid stabilizes the transverse phase-space evolution and suppresses RF-induced distortions, establishing a robust and reproducible operating point for subsequent vortex-beam experiments.

08 π · mm · mrad <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

Future Experimental Prospects

The low-charge operating regime enables the investigation of single-electron states and their quantum properties <ref:2509.00732#pg7>. We have studied the evolution of Laguerre–Gaussian wave packets with the realistic OAM values under three propagation scenarios: free drift, acceleration in a uniform DC field, and acceleration in the standing-wave RF field of the S-band gun <ref:2509. p. 1

Where the paper says it

We also investigate the quantum evolution of the single-electron Laguerre–Gaussian (LG) wave packets with different OAM values, up to ℓ = 64ℏ, accelerated in the same realistic DC and RF fields. We find that quantum transverse spreading in both accelerating field configurations is strongly suppressed compared with free-space drift, due to the rapid increase of the longitudinal momentum.

00732#pg9>. Overall, the simulations show that the present injector configuration satisfies the beam-quality requirements for experiments on the photoemission-driven generation and acceleration of vortex electrons in the MeV energy range <ref:2509. p. 0
Where the paper says it

, Novosibirsk, 630090, Russia 4 Institute of Nuclear Physics, 1 Ibragimov Street, Almaty, 050032, Kazakhstan 5 Petersburg Nuclear Physics Institute of NRC ”Kurchatov Institute”, 1, mkr. Orlova roshcha, Gatchina, Leningradskaya Oblast, 188300, Russia Abstract We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at the Joint Institute for Nuclear Research, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM).

00732#pg7>. In combination with a dedicated RF–laser synchronization system and tested diffractive optics for generating ultraviolet vortex beams up to l = 64ħ, all prerequisites for photoemission-based generation of relativistic vortex electrons are in place <ref:2509. p. 0
Where the paper says it

The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons. 1 Introduction The generation of relativistic vortex electron beams – quantum states with a helical phase front and a quantized orbital angular momentum projection (OAM) – is attracting growing interest across accelerator, atomic, and nuclear physics, electron microscopy, quantum optics, and foundation of quantum mechanics [1, 2, 3, 4].

p. 0
Where the paper says it

The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons. 1 Introduction The generation of relativistic vortex electron beams – quantum states with a helical phase front and a quantized orbital angular momentum projection (OAM) – is attracting growing interest across accelerator, atomic, and nuclear physics, electron microscopy, quantum optics, and foundation of quantum mechanics [1, 2, 3, 4].

00732#pg7>.

Experimental Verification

To verify that the cathode solenoid has been properly designed and that its magnetic field provides effective beam stabilization, we performed additional particle-tracking simulations through the RF gun <ref:2509.00732#pg7>. The rms transverse spread does not exceed 5 mm, which allows the beam to be safely transported through the 14-mm-diameter coaxial aperture <ref:2509. p. 3

Where the paper says it

3 eV [36], the resulting mean kinetic energy and energy spread of emitted electrons lie in the sub-eV range, consistent with standard metallic photocathodes. With the UV laser rms beam size set to σx,y = 2 mm (equal to 4

00732#pg7>. The total beam loss does not exceed 13%, which indicates a satisfactory operating regime of the cathode solenoid and confirms its effectiveness for beam confinement <ref:2509. p. 1
Where the paper says it

We demonstrate that the solenoidal lens provides effective transverse-envelope control in the low-charge regime. Although the normalized emittance does not decrease below its intrinsic value, the solenoid stabilizes the transverse phase-space evolution and suppresses RF-induced distortions, establishing a robust and reproducible operating point for subsequent vortex-beam experiments.

00732#pg7>.

Phase Optimization

A simulated RF-phase scan was performed to determine the optimal injection phase <ref:2509.00732#pg7>. Maximum acceleration is achieved near φ0 ≈ 180◦, with a phase tolerance of about ±1◦ <ref:2509. p. 4

Where the paper says it

The operational working point of the test bench, selected to maximize the achievable energy gain at the available RF gradient, corresponds to φ0 ≈ 180◦ (see Appendix A). Although the accelerating field at the cathode is not maximal at this phase, this setting yields the highest exit energy under commissioning conditions.

00732#pg7>. The operational working region φ0 ≈ 179◦ – 181◦ <ref:2509. p. 4
Where the paper says it

Consequently, the transverse emittance evolution is governed primarily by RF-induced correlations and by magnetization effects associated with the solenoidal field, rather than by Coulomb forces. The operational working point of the test bench, selected to maximize the achievable energy gain at the available RF gradient, corresponds to φ0 ≈ 180◦ (see Appendix A).

00732#pg7>. The phase scan of the normalized transverse emittance (see Fig. p. 5
Where the paper says it

The symmetry between x and y confirms the predominantly axisymmetric dynamics. The normalized transverse emittance evolution is shown in Fig.

14) shows a pronounced overall increase with injection phase in the explored interval <ref:2509. p. 5
Where the paper says it

Figure 10 shows the transverse phase-space distribution at the RF-gun exit. The x–x ′ projection forms an approximately elliptical distribution with no pronounced filamentation, consistent with controlled envelope evolution.

00732#pg7>. This behaviour is primarily determined by the intrinsic field structure of the 1. p. 4
Where the paper says it

63 pC), collective space-charge effects are significant only within the first few millimeters after emission and rapidly diminish as the beam becomes relativistic. Consequently, the transverse emittance evolution is governed primarily by RF-induced correlations and by magnetization effects associated with the solenoidal field, rather than by Coulomb forces.

5-cell S-band RF gun operating in the π-mode: the axial electric field has a node close to the cathode plane, so the extraction field falls rapidly as the phase approaches the zero crossing <ref:2509. p. 1
Where the paper says it

Two solenoids – a cathode solenoid near the gun and a downstream focusing solenoid – shape the transverse phase space and control the beam size. 5-cell S-band RF gun operates in the π-mode at 2856 MHz [29].

00732#pg7>.

Beam Dynamics Without Solenoid

Transversely, the beam expands symmetrically in x and y (see Fig. 15) from 2 mm to nearly 5. p. 5

Where the paper says it

Figure 8: Simulated RMS transverse beam size σx,y along the beamline in the presence of the compensation solenoid. After a short matching region, the envelope remains nearly constant at ≈ 2.

5 mm in the absence of external focusing <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>. At the present low bunch charge (0.63 pC) and relatively large emission area, the space-charge forces are moderate and contribute mainly to the divergence of the transverse envelope <ref:2509. p. 4
Where the paper says it

63 pC), collective space-charge effects are significant only within the first few millimeters after emission and rapidly diminish as the beam becomes relativistic. Consequently, the transverse emittance evolution is governed primarily by RF-induced correlations and by magnetization effects associated with the solenoidal field, rather than by Coulomb forces.

00732#pg7>. The evolution of the normalized emittance, however, is dominated by correlated distortions from the transverse RF fields of the 1. p. 1
Where the paper says it

Although the normalized emittance does not decrease below its intrinsic value, the solenoid stabilizes the transverse phase-space evolution and suppresses RF-induced distortions, establishing a robust and reproducible operating point for subsequent vortex-beam experiments. We also investigate the quantum evolution of the single-electron Laguerre–Gaussian (LG) wave packets with different OAM values, up to ℓ = 64ℏ, accelerated in the same realistic DC and RF fields.

5-cell π-mode gun, rather than by space charge <ref:2509. p. 1
Where the paper says it

Two solenoids – a cathode solenoid near the gun and a downstream focusing solenoid – shape the transverse phase space and control the beam size. 5-cell S-band RF gun operates in the π-mode at 2856 MHz [29].

00732#pg7>.

RF-Induced Distortions

After initial RF-induced oscillations inside the 1.5-cell gun, the emittance remains approximately constant at the cavity exit and subsequently increases due to nonlinear RF-field–induced transverse phase-space distortions <ref:2509. p. 5

Where the paper says it

In the absence of strong nonlinear forces, this value remains constant throughout the remainder of the beamline, indicating that the intrinsic transverse phase-space area is preserved during linear transport. Figure 10: Simulated transverse phase space of the electron beam at the RF-gun exit.

00732#pg7>. Without external focusing, the beam size diverges rapidly and RF-induced emittance growth cannot be mitigated, motivating the use of a compensation solenoid in the following section <ref:2509. p. 3
Where the paper says it

The laser transport line consists of an atmospheric transport section and a vacuum section delivering the beam to the cathode via a 45◦ metallic mirror; a 2500-mm focal-length lens produces a 2 mm laser rms beam size on the photocathode. The emittance-compensation solenoid prototype (see Fig.

00732#pg7>. The oscillations become particularly relevant when a solenoidal field is introduced, since the RF–solenoid coupling modifies their cancellation <ref:2509. p. 5
Where the paper says it

The interplay between the solenoidal field and the transverse RF fields of the 1. 5-cell π-mode gun modifies the natural cancellation of RF-induced correlations that occurs in the zero-solenoid case [37].

00732#pg7>.

Transverse Envelope Control

Inside the solenoid region, the emittance exhibits a pronounced increase, reaching approximately εn,x,y ≈ 5.6 π·mm · mrad, which reflects the magnetization acquired by the beam in the presence of a non-zero axial magnetic field at the cathode <ref:2509. p. 5

Where the paper says it

Inside the solenoid region, the emittance exhibits a pronounced increase, reaching approximately εn,x,y ≈ 5. 6 π·mm · mrad, which reflects the magnetization acquired by the beam in the presence of a non-zero axial magnetic field at the cathode.

00732#pg7>. Downstream of the solenoid, the projected emittance decreases and converges to a stationary value of εn,x,y = 2. p. 5
Where the paper says it

5-cell π-mode gun modifies the natural cancellation of RF-induced correlations that occurs in the zero-solenoid case [37]. Downstream of the solenoid, the projected emittance decreases and converges to a stationary value of εn,x,y = 2.

08 π · mm · mrad <ref:2509.00732#pg7>. In the absence of strong nonlinear forces, this value remains constant throughout the remainder of the beamline, indicating that the intrinsic transverse phase-space area is preserved during linear transport <ref:2509. p. 5
Where the paper says it

08 π · mm · mrad. In the absence of strong nonlinear forces, this value remains constant throughout the remainder of the beamline, indicating that the intrinsic transverse phase-space area is preserved during linear transport.

00732#pg7>.

Quantum State Preservation

In both accelerating cases, the rapid growth of electron momentum has substantially suppressed transverse spreading compared to free-space propagation, while preserving the characteristic radial structure of the OAM-carrying states <ref:2509.00732#pg9>. This suppression enables realistic estimates of the transverse coherence length of electron wave packets in the photogun under experimentally achievable conditions <ref:2509. p. 1

Where the paper says it

We find that quantum transverse spreading in both accelerating field configurations is strongly suppressed compared with free-space drift, due to the rapid increase of the longitudinal momentum. This suppression enables realistic estimates of the transverse coherence length of electron wave packets in the photogun under experimentally achievable conditions.

00732#pg9>. By understanding and controlling this fundamental quantum spreading, photoinjector designs can be optimized to maintain the quality and characteristic properties of the vortex beams throughout the early acceleration stages <ref:2509. p. 9
Where the paper says it

This provides guidance for preserving spatial coherence and OAM content during beam transport and acceleration. By understanding and controlling this fundamental quantum spreading, photoinjector designs can be optimized to maintain the quality and characteristic properties of the vortex beams throughout the early acceleration stages.

00732#pg9>.

Final Assessment

Overall, the simulations show that the present injector configuration satisfies the beam-quality requirements for experiments on the photoemission-driven generation and acceleration of vortex electrons in the MeV energy range <ref:2509.00732#pg7>. The photoinjector has reached first beam, and commissioning toward the design RF input power of 6 MW is ongoing <ref:2509. p. 2

Where the paper says it

Although the gun is designed for up to 6 MW of input RF power, the present test-bench operation is limited to about 3 MW because the cavity is still undergoing RF aging. Thus the 45 MV/m accelerating gradient used in the simulations corresponds to the experimentally achievable field at this commissioning stage.

00732#pg7>. In combination with a dedicated RF–laser synchronization system and tested diffractive optics for generating ultraviolet vortex beams up to l = 64ħ, all prerequisites for photoemission-based generation of relativistic vortex electrons are in place <ref:2509.00732#pg7>. The check of the electron beams vorticity can be made by diffraction on a triangle apperture, as has been discussed in Ref. p. 6
Where the paper says it

, is the radial quantum number, L ℓ n denotes the generalized Laguerre polynomial, σ⊥(t) is the transverse beam size of the fundamental LG mode: for n = ℓ = 0, and td is the characteristic diffraction time. It is important to note that the azimuthal phase factor exp(iℓϕr) makes the state an eigenfunction of the OAM operator, Lˆ z ψℓ,n = −iℏ ∂ ∂ϕr ψℓ,n = ℓℏ ψℓ,n, and it is the defining feature of vortex beams: it produces the characteristic helical phase front and ensures that each electron carries an orbital momentum projection ℓℏ with respect to the propagation axis.

[44] <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

Acknowledgments

The authors express their gratitude to A.V. Vukolov, M.V. Shevelev, and G.K. Sizykh for their significant assistance in developing the beam emittance diagnostics <ref:2509. p. 4

Where the paper says it

63 pC), collective space-charge effects are significant only within the first few millimeters after emission and rapidly diminish as the beam becomes relativistic. Consequently, the transverse emittance evolution is governed primarily by RF-induced correlations and by magnetization effects associated with the solenoidal field, rather than by Coulomb forces.

00732#pg7>. We also thank E.A. Yakushev, V.V. Glagolev, D. V. Naumov, A.S. Zhemchugov, and the management of the Laboratory of Nuclear Problems for supporting the project on behalf of JINR <ref:2509. p. 1
Where the paper says it

Realizing this mechanism requires a photoinjector capable of producing low-emittance beams with well-controlled transverse profiles and rapid acceleration, ensuring that the initial OAM-imprinted phase structure of the emitted electron is preserved during the early acceleration. To this end, a dedicated S-band RF photoinjector test bench is being developed at the Laboratory of Nuclear Problems, Joint Institute for Nuclear Research (JINR), combining a 1.

00732#pg7>. Special thanks are due to K. p. 9
Where the paper says it

In the regime t ≫ td, where the transverse width obeys σ⊥(t) ∝ t, this kinematic shortening leads to an ∼ 900-fold suppression of the transverse rms size compared to the free electron at z = 30 cm, as shown in Fig. Importantly, similar suppression of quantum spreading persists for all other parameter sets explored in this work, indicating that strong reduction of transverse spreading is a robust feature of relativistic acceleration rather than a special property of the specific cases illustrated in Figs.

V. Cherepanov and N.E. Sheremet for their help with quantum dynamics calculations, and to S. p. 7
Where the paper says it

For typical DC-gun this results in a ∼ 550-fold reduction of the final transverse width compared to free-space propagation (see Fig. 11), in good agreement with recent relativistic calculations [40].

S. Baturin for valuable consultations <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>. This study was supported by the Russian Science Foundation (Project No. p. 0
Where the paper says it

The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons. 1 Introduction The generation of relativistic vortex electron beams – quantum states with a helical phase front and a quantized orbital angular momentum projection (OAM) – is attracting growing interest across accelerator, atomic, and nuclear physics, electron microscopy, quantum optics, and foundation of quantum mechanics [1, 2, 3, 4].

23-62-10026) [45] <ref:2509. p. 0
Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

References

[1] B. A. Knyazev and V. G. Serbo, Phys. Usp. 61, 449 (2018) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[2] K. Bliokh, I. Ivanov, G. Guzzinati, L Clark, R Van Boxem, A B´ech´e, R Juchtmans, M Alonso, P Schattschneider, F Nori and J Verbeeck Phys Reports 690 1 (2017), theory and applications of free-electron vortex states <ref:2509. p. 0

Where the paper says it

The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons. 1 Introduction The generation of relativistic vortex electron beams – quantum states with a helical phase front and a quantized orbital angular momentum projection (OAM) – is attracting growing interest across accelerator, atomic, and nuclear physics, electron microscopy, quantum optics, and foundation of quantum mechanics [1, 2, 3, 4].

00732#pg7>.

[3] D Karlovets New Journal of Physics 23, 033048 (2021) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[4] I P Ivanov Progress in Particle and Nuclear Physics 127, 103987 (2022) <ref:2509. p. 0

Where the paper says it

com 1 arXiv:2509. 00732v4 [physics.

00732#pg7>.

[5] M Uchida and A Tonomura Nature 464, 737– (2010) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[6] J Verbeeck H Tian and P Schattschneider Nature 467, 301 (2010) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[7] A Blackburn and J Loudon Ultramicroscopy 136, 127 (2014) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[8] P Schattschneider B Schaffer I Ennen and J Verbeeck Phys Rev. B 85, 134422 (2012) <ref:2509. p. 0

Where the paper says it

karlovets@gmail. com 1 arXiv:2509.

00732#pg7>.

[9] Y Wu L Ji X Geng Q Yu N Wang B Feng Z Guo W Wang C Qin X Yan L Zhang J Thomas A H¨utzen M B¨uscher T P Rakitzis A Pukhov B Shen and R Li New Journal of Physics 21, 073052 (2019) <ref:2509. p. 0

Where the paper says it

com 1 arXiv:2509. 00732v4 [physics.

00732#pg7>.

[10] I P Ivanov N Korchagin A Pimikov and P Zhang Phys Rev. D 101, 096010 (2020) <ref:2549.

Final Output Generation

We present beam-dynamics simulations for an S-band RF photoinjector test bench under development at JINR, aimed at producing high-quality electron beams and enabling future generation of relativistic vortex electrons with a quantized orbital angular momentum (OAM) <ref:2509.00732#pg15>. Simulations of the 1.5-cell photogun are performed assuming an RF gradient of 45 MV/m, which, in accordance with our simulations with CST Studio, corresponds to the currently achieved input RF power of 3 MW <ref:2509.00732#pg4>. At low charge (Q = 0.63 pC), stable bunch formation is obtained, with weak space-charge effects and transverse emittance dominated by RF-induced correlations <ref:2509.00732#pg5>. Optimization of the injection phase and cathode solenoid results in a robust emittance-compensated regime with a final normalized emittance of 2.08 π ·mm · mrad <ref:2509.00732#pg7>. To assess prospects for accelerating vortex electron beams, we additionally model the quantum evolution of single-electron Laguerre–Gaussian wave packets <ref:2509.00732#pg9>. The results show that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure, indicating that the test bench provides suitable conditions for forthcoming experimental studies of relativistic vortex electrons <ref:2509.00732#pg9>.

To analyze the generation of relativistic vortex electrons carrying OAM, we follow the quantum evolution of a single-electron wave packet during acceleration <ref:2509.00732#pg9>. We compare three representative cases: 1. Free-space propagation over the RF photogun length; 2. Acceleration in a uniform DC electric field, corresponding to a simplified DC-gun model; and 3.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Beam dynamics simulation for high-quality electron beams allows AI systems to predict stable operating points by modeling weak space-charge effects and transverse emittance dominated by RF-induced correlations. This enables AI to design optimized injection phases and solenoid settings that yield a robust emittance-compensated regime with a final normalized emittance of 2.08 pi ·mm · mrad.

  2. Quantum evolution analysis allows AI to predict the preservation of structured quantum states, showing that multi-MeV acceleration suppresses free-space spreading of the electron packet and preserves the packet’s initial OAM structure. This capability is crucial for designing accelerators capable of producing relativistic vortex electrons by ensuring their helical phase front and a quantized orbital angular momentum projection l hZ.

  3. The study on quantum evolution provides guidance for maintaining beam quality, as it shows that the relativistic acceleration leads to an ∼ 900-fold suppression of the transverse rms size compared to the free electron at z = 30 cm. This allows AI to optimize injector designs to maintain the quality and characteristic properties of the vortex beams throughout the early acceleration stages.

Abstract

We present the design and an analysis of the classical and quantum beam dynamics for an S-band radio-frequency (RF) photoinjector dedicated to the generation of relativistic vortex electron beams carrying a quantized orbital angular momentum (OAM). The field-map-based tracking simulations were performed in the ultra-low bunch charge regime (Q = 0.63 pC), where space-charge effects are strongly suppressed. We demonstrate that optimizing the injection phase and solenoidal focusing preserves the intrinsic thermal limit of the photoemission source, yielding a stable, emittance-compensated beam with a final kinetic energy of 4.9 MeV and a normalized transverse emittance of 56,π,μ m times mrad. Furthermore, our quantum-mechanical analysis of single-electron Laguerre-Gaussian wave packets inside the designed accelerating fields reveals that rapid energy gain suppresses transverse quantum spreading by nearly three orders of magnitude compared to free-space propagation. This suppression protects the characteristic OAM-dependent spatial structure of the wave packet. These results establish the beam-dynamics operating regime and vacuum conditions required for subsequent experiments on the generation and transport of relativistic vortex electron beams.

Related papers