Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV Photodetectors
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV Photodetectors".
Mira: Here's the gist of the paper. Silver phenylselenide (AgSePh), known as mithrene, is a two-dimensional (2D) organic-inorganic chalcogenide (MOC) semiconductor with a wide direct band gap, narrow blue emission and in-plane anisotropy <ref:2506.22535#pg2> The pre-tarnishing process, combined with organic ligands, resulted in large crystals exceeding 1 μm and improved homogeneous in-plane orientation <ref:2506.22535#pg5> Furthermore, the films were integrated on planar graphene field-effect phototransistors (GFETs) and demonstrated photoresponsivity beyond 100 A/W at 450 nm, highlighting mithrene's potential for blue light-detection applications <ref:2506.22535#pg2> Material Properties of Mithrene Mithrene is a MOC semiconductor with a wide and direct band gap, low-temperature growth (≤100°C), ultrastrong light‒matter coupling, capability for UV-blue light absorption, and narrow blue (∼467 nm) emission <ref:2506.22535#pg3> The bandgap and, hence, the light absorption of mithrene can be tuned by modifying its organic ligands <ref:2506.22535#pg2> It is a promising lead-free alternative for light detection applications in the UV‒blue range <ref:2506.22535#pg2> Synthesis Control Strategies The authors introduced a thermally assisted conversion (TAC) technique for the scalable growth of mithrene at 100°C <ref:2506.22535#pg4> This technique induces the formation of silver complexes through gentle water (H2O) vapor pulses and the addition of propylamine (PrNH2) organic ligands during the growth process <ref:2506.22535#pg2> The organic ligands play two roles: promoting the formation of a key reactive intermediate and slowing the conversion reaction to AgSePh, which leads to higher-quality crystals <ref:2506.22535#pg2> Effect of Pre-treatment Methods Two different pre-tarnishing methods were employed for synthesis, namely O2 plasma treatment and H2O vapor pulse treatment <ref:2506.22535#pg2> The O2 plasma treatment resulted in irregular mithrene crystals formed through the O2 plasma treatment process <ref:2506.22535#pg5> In contrast, water vapor exposure maintains the silver surface topography as nearly dense and slows down crystal growth, allowing for the formation of higher-quality crystals <ref:2506.22535#pg2> The addition of PrNH2 during the growth reaction can regulate the strain in AgSePh crystals <ref:2506.22535#pg2> Device Performance and Validation The Mithrene/GFET PDs showed responsivities beyond 100 A/W at 450 nm through a photogating mechanism <ref:2506.22535#pg2> The time-resolved response to changes in illumination was characterized, showing a rise time of less than 50 ms and a fall time of less than 150 ms <ref:2506.22535#pg2> The analysis confirmed that the observed anisotropy in the optical refractive index and extinction coefficients is attributed to a strong (001) preferential orientation of the crystalline domains in the film <ref:2506.22535#pg5> Wafer-Scale Fabrication Mithrene thin films were grown on a 100 mm wafer and selectively on a chip with predefined silver structures <ref:2506.22535#pg2> The average ordinary and extraordinary refractive indices at 1.96 eV (632 nm) closely matched those obtained from a single-spot measurement, demonstrating a uniform in-plane refractive index distribution <ref:2506.22535#pg5> The thickness across the wafer ranged from 100-140 nm <ref:2506.22535#pg2> Photodetector Functionality The PDs showed that under illumination, holes are introduced into the graphene, while electrons remain in the mithrene layer <ref:2506.22535#pg2> The remaining charge carriers in the mithrene layer function as a secondary gate (photogating), further enhancing the photocurrent <ref:2506.22535#pg2> This mechanism validates mithrene's reliability as an air-stable photoactive layer <ref:2506.22535#pg2> Characterization Techniques Used The mithrene thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-visible (UV-vis) and photoluminescence (PL) spectroscopy, grazing-incidence wide-angle X-ray scattering (GIWAXS), and spectroscopic ellipsometry <ref:2506.22535#pg2> Automated refractive index mapping on 100 mm wafer was conducted using a Philips PQ Ruby Ellipsometer at 632 nm <ref:2506.22535#pg5> GIWAXS measurements were performed at the FCM beamline of the Physikalisch-Technische Bundesanstalt laboratory <ref:2506.22535#pg2> Raman spectroscopy was used to compare the graphene quality before and after silver deposition <ref:2506.22535#pg5> The responsivity (R (A/W)) was calculated using the formula R=IPhoto/PIllumination×A <ref:2506.22535#pg2> In summary, we demonstrate wafer-scale (100 mm) mithrene growth for the first time using a solidvapor-phase chemical transformation process of metallic silver to mithrene (AgSePh) with controlled pre-tarnishing by H2O vapor pulse treatment <ref:2506.22535#pg2> The H2O vapor pulses, combined with PrNH2 as an organic coordinating ligand, reduced the reactivity of Ag+ ions and slowed the conversion process, yielding flatter, larger crystals exceeding 1 μm with (001) preferred orientation and a high in-plane extinction coefficient <ref:2506.22535#pg2> The mithrene films were integrated into GFETs without significantly damaging the graphene, as evidenced by Raman spectroscopy <ref:2506.22535#pg5> Furthermore, we demonstrated Mithrene/GFET PDs based on charge carrier transfer into the graphene <ref:2506.22535#pg2> The PDs showed responsivities beyond 100 A/W at 450 nm through a photogating mechanism, validating mithrene's reliability as an air-stable photoactive layer <ref:2506.22535#pg2> The authors thank P.
Kai: Grewe and Dr.
Mira: U.
Kai: Böttger (Electronic Material Research Lab, RWTH Aachen University) for their support in the XRD measurements <ref:2506.22535#pg2> References
1: C.
Title and authors: Kai: So they’re focusing on that synthesis control using this TAC method to get better crystal quality. They mention that standard methods, like using oxygen plasma or UV-assisted tarnishing, just don't give them the precise control they need over the lateral size and the crystal orientation in their thin films.
Mira: That makes sense because those standard solid vapor phase methods leave you with unpredictable crystals. The authors introduce gentle water vapor pulses and add propylamine organic ligands during that growth process to help guide things.
Lev: And those organic ligands are key, I guess, because the paper says they do two jobs: first, they promote the formation of some reactive intermediate, and second, they slow down the actual conversion reaction to form mithrene.
Kai: That slowing down aspect is what you need when you're trying to grow something big and well-ordered on a large scale. If the reaction happens too fast, you get defects or irregular shapes instead of those larger crystals they’re aiming for.
Mira: The result they describe is that this TAC technique improves both the lateral crystal size and the orientation, and they also see an increase in photoluminescence intensity, which is another good sign for material quality.
Lev: Increasing photoluminescence intensity usually means fewer defects, so that ties back into what you need for high-quality optical components. But how much of a difference does this actually make when you move to a wafer scale?
Kai: Well, the paper shows they are achieving crystals exceeding one micrometer in size with this method. That’s a significant jump from what was previously possible with the older techniques.
Mira: And that large size, combined with the improved orientation, is what sets up these materials for better optical performance in their photodetector setup. It directly addresses the limitation they identified at the start of the paper about crystal quality hindering application.
Lev: But we have to consider if that one micrometer size is enough when you're looking at integrating this into a complex device structure where uniformity across a one hundred millimeter wafer matters immensely <ref:2506.22535#pg3>.
Kai: That’s what they address next, moving from the crystal structure itself to how they test it in a real application context. They show these films integrated onto planar graphene field-effect phototransistors, or GFETs.
Mira: And on those GFETs, they demonstrate photoresponsivity beyond one hundred amperes per watt when illuminated at four hundred fifty nanometers <ref:2506.22535#pg3>. That’s actually pretty high sensitivity for a material in this class.
Lev: One hundred amperes per watt is a substantial number, especially when you're talking about low-temperature growth conditions of around one hundred degrees Celsius. What does that responsiveness tell us about the device efficiency?
Kai: It shows mithrene has potential for blue light detection because it’s performing well in that UV-blue range, which is where silicon struggles. It validates their choice of material for this specific application area.
Mira: The paper also points out how the bandgap and therefore the light absorption can be tuned just by changing those organic ligands they add to the material. That flexibility is a big plus for device optimization later on.
Lev: Tuning the bandgap by changing ligands is helpful, but you still have to worry about controlling those internal strain effects when you grow it, which we talked about before.
Kai: Right, so they are using the propylamine ligand not just to slow down the reaction but also to regulate some of that strain inside the silver phenylselenide crystals. That’s a clever dual role for the ligand.
Mira: It sounds like they're trying to use chemistry during synthesis to control structure and electronic properties simultaneously, which is exactly what we hoped this new method would achieve for mithrene.
The paper's summary: Kai: So, summarizing the core of this work from "Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV Photodetectors", they are showing how they moved from a problem where mithrene was hard to grow on large scales to a successful method using thermally assisted conversion <ref:2506.22535#pg1,Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV>.
Mira: They summarize that the key innovation is the TAC technique, which uses water vapor pulses and propylamine ligands at one hundred degrees Celsius to produce high-quality, larger crystals with better orientation compared to previous solid vapor phase methods.
Lev: So, they’re saying that by controlling those chemical inputs—the water vapor and the organic ligands—they can get a material structure that is fundamentally superior for device fabrication than what was previously achievable.
Kai: And they highlight the practical application: integrating these high-quality films onto GFETs to create photodetectors, showing responsivities over one hundred amperes per watt at four hundred fifty nanometers <ref:2506.22535#pg3>.
Mira: Essentially, the summary is that mithrene is a promising lead-free alternative for UV-blue light detection because they’ve successfully shown that you can grow it on a wafer and get the necessary crystal quality to actually detect light efficiently.
Lev: But we need to look at the caveats they mentioned in their summary, specifically regarding the challenges of scaling up this process reliably and consistently across a full wafer.
Kai: Right, and they did mention that while they achieved wafer-scale growth, ensuring that the refractive index is uniform across the entire film thickness from one end of the one hundred millimeter wafer to the other was something they had to verify <ref:2506.22535#pg3>.
Mira: They used some mapping techniques on the wafer, like automated refractive index mapping with a Philips PQ Ruby Ellipsometer at six hundred thirty two nanometers. That’s how they checked for that uniformity across their large-area sample.
Lev: I'm curious about the measurement itself, because if the refractive index isn't uniform, all that good crystal control won't help you get a stable device performance.
Kai: The data they got was consistent with what you’d expect from a single spot measurement, which suggests they achieved that uniform in-plane distribution across the wafer.
The paper's improvements: Kai: So, what are the specific improvements the authors suggest as enhancements to their synthesis method? They seem to be emphasizing the control aspect of the TAC process over just making it work.
Mira: They are pushing for tighter control over reaction parameters because they’ve shown that this level of control directly leads to higher quality crystals and better photoluminescence intensity.
Lev: And from my point of view, the paper suggests that optimizing the organic ligand concentration is crucial because it balances the promotion of the reactive intermediate with slowing down the conversion rate.
Kai: So, it’s not just adding a ligand for one reason; it’s about tuning two competing chemical effects to get that perfect structural outcome. That's a sophisticated level of control they are aiming for.
Mira: And they also suggest that tailoring the organic ligands is the way to tune the bandgap itself, which means you can optimize it for different detection wavelengths rather than just accepting a fixed property.
Lev: If you can tune it, then you aren't stuck with one specific wavelength limitation; that opens up possibilities for designing detectors specifically for certain parts of the UV-blue spectrum.
Kai: So the overall improvement is moving from just finding *a* way to synthesize mithrene to having a tunable synthesis route where you can control crystal size, orientation, and electronic properties all at once.
Mira: That moves it from being a static material with fixed properties to something that can be engineered based on the synthesis parameters used.
Conclusion: Kai: So wrapping up the paper "Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV Photodetectors", the main implication is that they have successfully demonstrated a wafer-scale growth process for mithrene <ref:2506.22535#pg1,Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV>. They’ve shown it can be done reliably using the TAC method.
Mira: They showed that this isn't just a lab curiosity anymore; it’s a viable candidate for next-generation optoelectronic applications because of the high responsivity they measured under illumination at four hundred fifty nanometers.
Lev: From an engineering standpoint, I think the main thing is that this work proves the process is scalable to one hundred millimeter wafers, which means we can start thinking about production rather than just proof-of-concept samples <ref:2506.22535#pg3>.
Kai: It’s about moving toward a material that's controllable on a wafer, and they’ve done that for mithrene using controlled tarnishing by water vapor pulses.
Mira: And the final point is that because they can tune the crystal structure and bandgap, it opens up avenues for designing tailored detectors for specific UV-blue light detection needs.
Lev: So while they proved the synthesis works on a wafer, we still need to figure out how to reliably integrate those films into a robust GFET structure without causing damage or introducing noise during operation.
Kai: That’s the next big challenge then, moving from material growth success to building a functional, stable photodetector that can run for long periods.
Mira: Exactly. We have this promising new synthesis method and we have these high-performance measurements to work with as we look at how mithrene fits into the broader picture of 2D semiconductor research <ref:2506.22535#pg1>.
Lev: So that’s the gist of this paper on "Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV Photodetectors" <ref:2506.22535#pg1,Wafer-scale Synthesis of Mithrene and its Application in 2D Heterostructure UV>. We’ve seen they controlled crystal size, achieved wafer scale growth, and demonstrated high responsivity through photogating.
Maryam Mohammadi, *Stefanie L. Stoll, Analía F. Herrero, Sana Khan, Federico Fabrizi, Christian Gollwitzer, Zhenxing Wang, §Surendra B. Anantharaman 1, 4*, *Max C. Lemme
AMO GmbH · Physikalisch-Technische Bundesanstalt · Chair of Electronic Devices, RWTH Aachen University · Low-dimensional Semiconductors Lab, Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras
cond-mat.mtrl-sci, physics.app-ph
Submitted: 2025-06-27
Updated: 2025-06-27
Comments: 26 pages
Journal ref: Advanced Functional Materials 36 (15), e17857, 2026
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 91/100
The gist: Silver phenylselenide (AgSePh), known as mithrene, is a two-dimensional (2D) organic-inorganic chalcogenide (MOC) semiconductor with a wide direct band gap…
Key concepts
- Mithrene (AgSePh)
- Mithrene is a two-dimensional organic-inorganic semiconductor that absorbs UV-blue light and emits narrow blue light. Its bandgap can be tuned by changing its organic ligands, making it a potential lead-free material for UV detection applications.
- Thermally Assisted Conversion (TAC)
- This synthesis technique involves growing mithrene at 100°C using gentle pulses of water vapor and propylamine ligands. The organic ligands help control the reaction, leading to higher-quality crystals with better crystal structure and orientation.
- Photogating Mechanism
- In the Mithrene/GFET photodetectors, light excites holes in graphene while electrons remain in the mithrene layer. These trapped charges in mithrene act as a secondary gate, enhancing the photocurrent and validating its use as an air-stable photoactive layer.
Terminology
Summary
Silver phenylselenide (AgSePh), known as mithrene, is a two-dimensional (2D) organic-inorganic chalcogenide (MOC) semiconductor with a wide direct band gap, narrow blue emission and in-plane anisotropy <ref:2506. p. 022535#pg2> The pre-tarnishing process, combined with organic ligands, resulted in large crystals exceeding 1 μm and improved homogeneous in-plane orientation <ref:2506. p. 022535#pg5> Furthermore, the films were integrated on planar graphene field-effect phototransistors (GFETs) and demonstrated photoresponsivity beyond 100 A/W at 450 nm, highlighting mithrene's potential for blue light-detection applications <ref:2506.22535#pg2>
Material Properties of Mithrene
Mithrene is a MOC semiconductor with a wide and direct band gap, low-temperature growth (≤100°C), ultrastrong light‒matter coupling, capability for UV-blue light absorption, and narrow blue (∼467 nm) emission <ref:2506.22535#pg3> The bandgap and, hence, the light absorption of mithrene can be tuned by modifying its organic ligands <ref:2506. p. 122535#pg2> It is a promising lead-free alternative for light detection applications in the UV‒blue range <ref:2506. p. 122535#pg2>
Synthesis Control Strategies
The authors introduced a thermally assisted conversion (TAC) technique for the scalable growth of mithrene at 100°C <ref:2506.22535#pg4> This technique induces the formation of silver complexes through gentle water (H2O) vapor pulses and the addition of propylamine (PrNH2) organic ligands during the growth process <ref:2506. p. 222535#pg2> The organic ligands play two roles: promoting the formation of a key reactive intermediate and slowing the conversion reaction to AgSePh, which leads to higher-quality crystals <ref:2506. p. 222535#pg2>
Effect of Pre-treatment Methods
Two different pre-tarnishing methods were employed for synthesis, namely O2 plasma treatment and H2O vapor pulse treatment <ref:2506.22535#pg2> The O2 plasma treatment resulted in irregular mithrene crystals formed through the O2 plasma treatment process <ref:2506. p. 322535#pg5> In contrast, water vapor exposure maintains the silver surface topography as nearly dense and slows down crystal growth, allowing for the formation of higher-quality crystals <ref:2506. p. 522535#pg2> The addition of PrNH2 during the growth reaction can regulate the strain in AgSePh crystals <ref:2506. p. 522535#pg2>
Device Performance and Validation
The Mithrene/GFET PDs showed responsivities beyond 100 A/W at 450 nm through a photogating mechanism <ref:2506.22535#pg2> The time-resolved response to changes in illumination was characterized, showing a rise time of less than 50 ms and a fall time of less than 150 ms <ref:2506. p. 922535#pg2> The analysis confirmed that the observed anisotropy in the optical refractive index and extinction coefficients is attributed to a strong (001) preferential orientation of the crystalline domains in the film <ref:2506. p. 722535#pg5>
Wafer-Scale Fabrication
Mithrene thin films were grown on a 100 mm wafer and selectively on a chip with predefined silver structures <ref:2506.22535#pg2> The average ordinary and extraordinary refractive indices at 1. p. 796 eV (632 nm) closely matched those obtained from a single-spot measurement, demonstrating a uniform in-plane refractive index distribution <ref:2506. p. 822535#pg5> The thickness across the wafer ranged from 100-140 nm <ref:2506. p. 722535#pg2>
Photodetector Functionality
The PDs showed that under illumination, holes are introduced into the graphene, while electrons remain in the mithrene layer <ref:2506.22535#pg2> The remaining charge carriers in the mithrene layer function as a secondary gate (photogating), further enhancing the photocurrent <ref:2506. p. 922535#pg2> This mechanism validates mithrene's reliability as an air-stable photoactive layer <ref:2506.22535#pg2>
Characterization Techniques Used
The mithrene thin films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), UV-visible (UV-vis) and photoluminescence (PL) spectroscopy, grazing-incidence wide-angle X-ray scattering (GIWAXS), and spectroscopic ellipsometry <ref:2506.22535#pg2> Automated refractive index mapping on 100 mm wafer was conducted using a Philips PQ Ruby Ellipsometer at 632 nm <ref:2506. p. 722535#pg5> GIWAXS measurements were performed at the FCM beamline of the Physikalisch-Technische Bundesanstalt laboratory <ref:2506. p. 022535#pg2> Raman spectroscopy was used to compare the graphene quality before and after silver deposition <ref:2506. p. 822535#pg5> The responsivity (R (A/W)) was calculated using the formula R=IPhoto/PIllumination×A <ref:2506.22535#pg2>
Conclusion of Synthesis
In summary, we demonstrate wafer-scale (100 mm) mithrene growth for the first time using a solidvapor-phase chemical transformation process of metallic silver to mithrene (AgSePh) with controlled pre-tarnishing by H2O vapor pulse treatment <ref:2506.22535#pg2> The H2O vapor pulses, combined with PrNH2 as an organic coordinating ligand, reduced the reactivity of Ag+ ions and slowed the conversion process, yielding flatter, larger crystals exceeding 1 μm with (001) preferred orientation and a high in-plane extinction coefficient <ref:2506. p. 022535#pg2> The mithrene films were integrated into GFETs without significantly damaging the graphene, as evidenced by Raman spectroscopy <ref:2506. p. 022535#pg5> Furthermore, we demonstrated Mithrene/GFET PDs based on charge carrier transfer into the graphene <ref:2506. p. 022535#pg2> The PDs showed responsivities beyond 100 A/W at 450 nm through a photogating mechanism, validating mithrene's reliability as an air-stable photoactive layer <ref:2506.22535#pg2> The authors thank P. p. 0 Grewe and Dr. U. Böttger (Electronic Material Research Lab, RWTH Aachen University) for their support in the XRD measurements <ref:2506. p. 022535#pg2>
References
[1] C. Liu, J. Guo, L. Yu, J. Li, M. Zhang, H. Li, Y. Shi, D. Dai <ref:2506.22535#pg2>
[9] G Wang, S Luo, T Di <ref:2506.22535#pg2>
[10] W Paritmongkol, T Sakurada <ref:2506.22535#pg2>
[42] D S. Schneider, A Grundmann <ref:2506.22535#pg5>
Supporting Information
Figure S8 shows the Spectroscopic ellipsometry mapping for the mithrene growth on the 100 mm wafer <ref:2506.22535#pg5> Figure S9a shows Raman peaks of single-layer graphene before and after Ag deposition <ref:2506. p. 822535#pg5> The Raman spectra in Figure S9a show the characteristic G and 2D bands at approximately 1587 cm−1 and 2700 cm−1, respectively <ref:2506. p. 322535#pg5> After silver deposition, a higher D peak appears, indicating more defects <ref:2506.22535#pg5> The data taken before Ag deposition (black) shows a higher intensity of the 2D peak than the G peak, and a very small D peak, indicating a good quality of the single-layer graphene <ref:2506. p. 422535#pg5>
Final Reference
[1] R Nicolas, G Lévêque, P.-M Adam <ref:2506.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved synthesis control for mithrene allows for large crystal size and orientation, as demonstrated by
The pre-tarnishing process, combined with organic ligands, resulted in large crystals exceeding 1 μm and improved homogeneous in-plane orientation.
This enables the creation of high-quality materials necessary for advanced optoelectronic devices. -
Enhanced photodetector performance is achieved through integration into GFETs, where
The responsivities of various devices are shown in Figure 6e as a function of different illumination powers, exceeding 1 A/W due to the photogating effect.
This validates mithrene's potential for high-sensitivity blue light detection. -
Precise control over crystal lattice strain is possible by varying organic ligands, as
The addition of PrNH2 during the growth reaction can regulate the strain in AgSePh crystals.
This allows researchers to tune optical properties by controlling structural defects and surface passivation. -
Wafer-scale synthesis capability enables mass production, as shown by
We scale the method to 100 mm wafers and demonstrate 2D mithrene / graphene heterostructure PDs operating in the UV wavelength range.
This transitions mithrene from lab curiosity to a viable material for next-generation optoelectronics.
Related papers
- Structural contribution to light-induced gap suppression in Ta 2 NiSe 5
- Anatomy of fast current-induced skyrmion motion in synthetic antiferromagnets
- Magnetic control of an exciton-polariton condensate in a van der Waals magnet
- High-pressure elastic properties of GeO2 polymorphs up to 120 GPa
- Decoupling Strain-Rate Sensitivity and Deformation Length Scale Effects in Neutron-Irradiated Tungsten: A Coupled Nano-Indentation, HR-EBSD and Crystal Plasticity Study
- Magnetism modulation in Co3Sn2S2 by current-assisted domain wall motion