Current-induced torque in a MoS2-based device operating at room temperature

arXiv:2502.08483 · cond-mat.mes-hall, cond-mat.mtrl-sci · Submitted 2025-02-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Quantum Radio. Generated commentary on the latest quantum physics and condensed matter papers.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Current-induced torque in a MoS2-based device operating at room temperature".

Title and authors: Kai: Now we're going to look at the specific title again, "Current-induced torque in a MoS2-based device operating at room temperature." It really captures the essence of what they've done here.

Mira: That title points directly to the main mechanism, which is using charge current to induce torque in that MoS2 material.

Lev: It’s not just any torque; they are specifically looking at how this torque manifests in a device that operates right now, at room temperature, without needing some external field.

Kai: So what they did was build a system where the charge current flows through MoS2 and creates this switching effect using the orbital Hall effect.

Mira: The authors are pushing the idea that we can use this specific material to achieve field-free switching based on these intrinsic properties of it, rather than relying on external magnetic fields.

Lev: It’s about showing that charge current alone, under certain conditions, is enough to drive the system between its stable magnetic configurations.

Kai: The implication here is that we can start thinking about memory devices that are simpler because they don't need complicated field coils to operate the writing process.

The paper's summary: Mira: So, to summarize what this paper is saying, it’s proposing a novel memory device based on MoS2 where we have two stable states that can be read by measuring a voltage difference between the electrodes.

Kai: They detail how they use the spin-hall and orbital-hall effects in MoS2 to convert an electric current into perpendicular spin and orbital currents.

Lev: And those currents are then injected into cobalt electrodes, which have different shape anisotropies, allowing them to switch their magnetization states.

Mira: The main result is that they can deterministically switch between state zero and state one using a writing current density as low as three point two times ten to the power of four amperes per square centimeter <ref:2502.08483#pg1>.

Kai: They also highlight that they found that the switching is driven by an applied charge current, and not by an external magnetic field, making it a field-free mechanism.

Lev: They also suggest that because the orbital Hall conductivity in MoS2 is so large, this intrinsic property is the dominant driving force behind the differential voltage they observe.

Mira: It really frames the whole thing as being about harnessing huge internal material properties of MoS2 to get a low-power, room temperature switching mechanism.

The paper's improvements: Kai: The paper suggests that their design uses a novel setup where the spin-orbit torque is exerted not on a single electrode, but simultaneously on two cobalt electrodes with inplane magnetization and different shape anisotropy.

Mira: That simultaneous application to two electrodes with differing shapes is what allows them to achieve the deterministic switching between state zero and state one.

Lev: And they also point out that the operation can be characterized by two key aspects: the differential character of the output voltage measured between those magnetic electrodes with different shape anisotropy, and how fast the local electric current is tilted by an angle alpha with respect to the easy magnetization axis of that anisotropic electrode.

Kai: That tilt angle alpha is crucial because it allows for that easy switch between aligned and misaligned electrode magnetization states.

Mira: They also suggest they can perform non perturbative reading of these states using sub-threshold currents, suggesting you could read them with currents well below the threshold, like one point six milliamperes or even smaller.

Lev: That would require a really high signal to noise ratio because they are aiming to measure a difference of one microvolt between those two voltage states.

Conclusion: Kai: So putting it all together, this paper presents a novel spintronic device capable of field-free deterministic switching at room temperature using writing current densities as low as three point two times ten to the power of four amperes per square centimeter <ref:2502.08483#pg1>.

Mira: It achieves this by combining the spin-valve and spin-torque concepts for reading and writing operations in this MoS2 based architecture.

Lev: The key points are that the differential character of the output voltage between electrodes with different shape anisotropy, and that tilt of the local electric current by an angle alpha with respect to the easy magnetization axis.

Kai: They conclude that because of these two aspects, they can control which magnetization state you are in based on those fields and currents.

Mira: The big picture is that this shows that van der vaws materials are a good platform for developing unconventional non boolean memory devices for neuromorphic computation.

Lev: For real hardware, it means we need to figure out how to handle the switching current density of three point two times ten to the power of four amperes per square centimeter reliably and where the overhead really lands on actual chips <ref:2502.08483#pg1>.

Kai: That’s what they found in "Current-induced torque in a MoS2-based device operating at room temperature."

Antonio Bianco, Michele Ceccardi, Raimondo Cecchini, Daniele Marré, Chanchal K. Barman, Fabio Bernardini, Alessio Filippetti, Federico Caglieris, § Ilaria Pallecchi

Department of Physics, University of Genova CNR-SPIN Institute for superconductors innovative materials and devices CNR-ISMN Institute for the study of nanostructured materials Dipartimento di Fisica Università di Cagliari CNR Istituto Officina dei Materiali IOM Cagliari

cond-mat.mes-hall, cond-mat.mtrl-sci

Submitted: 2025-02-12

Updated: 2026-11-18

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 79/100

The gist: Charge-to-spin and spin-to-charge conversion mechanisms in high spin-orbit materials are the new frontier of memory devices.

Key concepts

Spin-Orbit Torque (SOT)
This mechanism converts a charge current flowing through a material like MoS2 into a spin current. This spin current then exerts a torque on the magnetization of adjacent ferromagnetic electrodes, allowing the device to switch its magnetic state by controlling the applied electrical current.
Orbital Hall Effect (OHE)
The paper suggests that the primary driving force for switching is not conventional spin-Hall effect but rather a huge orbital-Hall current within MoS2. This large intrinsic orbital-Hall conductivity is key to generating the necessary torque and causing the observed differential voltage.
Two Stable Memory States
The device utilizes two distinct stable configurations of magnetization in two Cobalt electrodes, labeled '0' and '1'. These states are read by measuring a specific differential voltage between the electrodes, which allows for non-volatile data storage.

Terminology

Summary

Charge-to-spin and spin-to-charge conversion mechanisms in high spin-orbit materials are the new frontier of memory devices. p. 0

Where the paper says it

pallecchi@spin. it Abstract Charge-to-spin and spin-to-charge conversion mechanisms in high spin-orbit materials are the new frontier of memory devices.

In this work, we propose a novel memory device based on the semiconducting two-dimensional centrosymmetric transition metal dichalcogenide (TMD) MoS2, that operates as a SOT device in the writing process and a spin valve in the reading process. p. 0
Where the paper says it

They operate via spin-orbit torque (SOT) switching of a magnetic electrode, driven by an applied charge current. In this work, we propose a novel memory device based on the semiconducting two-dimensional centrosymmetric transition metal dichalcogenide (TMD) MoS2, that operates as a SOT device in the writing process and a spin valve in the reading process.

We demonstrate that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3. p. 0
Where the paper says it

In this work, we propose a novel memory device based on the semiconducting two-dimensional centrosymmetric transition metal dichalcogenide (TMD) MoS2, that operates as a SOT device in the writing process and a spin valve in the reading process. We demonstrate that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3.

2x104 A/cm2 even in zero field, owed to a tilted geometry and a differential voltage architecture. p. 0
Where the paper says it

We demonstrate that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3. 2x104 A/cm2 even in zero field, owed to a tilted geometry and a differential voltage architecture.

Device Architecture and Operation

The proposed device utilizes MoS2 as the SOT material, where a longitudinal electric current is converted into perpendicular spin and orbital currents by spin-Hall and orbital-Hall effect, respectively. The switching mechanism involves exerting the SOT simultaneously on two Co electrodes with inplane magnetization and different shape anisotropy. p. 1

Where the paper says it

In this scenario, the possibilities of device designs with either perpendicular or planar magnetization states must be thoroughly explored, so as to take advantage of the full potential of both geometries and constituent materials. In this work, we propose a radically new MoS2-based device architecture, where the SOT is exerted not on a single electrode (as in conventional SOT architectures), but simultaneously on two Co electrodes with inplane magnetization and different shape anisotropy.

This design exploits the SOT to switch from an equally-magnetized electrode configuration (state ‘0’) to a configuration where both electrodes are in ferromagnetic monodomain but with unaligned magnetizations (state ‘1’). p. 1
Where the paper says it

In this work, we propose a radically new MoS2-based device architecture, where the SOT is exerted not on a single electrode (as in conventional SOT architectures), but simultaneously on two Co electrodes with inplane magnetization and different shape anisotropy. In this original design the SOT is exploited to switch from an equally-magnetized electrode configuration (state ‘0’) to a configuration where both electrodes are in ferromagnetic monodomain but with unaligned magnetizations (state ‘1’).

The two stable memory states are read as a differential voltage between the electrodes, and they are written by an applied current density as low as 3. p. 1
Where the paper says it

In this original design the SOT is exploited to switch from an equally-magnetized electrode configuration (state ‘0’) to a configuration where both electrodes are in ferromagnetic monodomain but with unaligned magnetizations (state ‘1’). These two, highly stable memory states are read as a differential voltage between the electrodes, and are written by an applied current density as low as 3.

2x104 A/cm2, a record-low value for SOT devices operating at room temperature. p. 1
Where the paper says it

These two, highly stable memory states are read as a differential voltage between the electrodes, and are written by an applied current density as low as 3. 2x104 A/cm2 , a record-low value for SOT devices operating at room temperature.

Fundamental Physics and Conversion

The paper suggests that the SOT originates by a huge orbital-Hall current in MoS2, which is then converted to spin current in the Co electrodes. Ab initio calculations point to the orbital Hall effect (OHE) as the most likely responsible for generating the SOT in the magnetic electrode. p. 0

Where the paper says it

An applied field 50-100 Oe can be used as a characterizing control parameter for the state switching. Ab initio calculations of spin Hall effect (SHE) and orbital Hall effect (OHE) point to the latter as the most likely responsible for the generation of the SOT in the magnetic electrode.

The large value of OHC in bulk MoS2 makes our device competitive in terms of energetic efficiency and could be integrated in TMD heterostructures to design memory devices with multiple magnetization states for non-Boolean computation. p. 0
Where the paper says it

Ab initio calculations of spin Hall effect (SHE) and orbital Hall effect (OHE) point to the latter as the most likely responsible for the generation of the SOT in the magnetic electrode. The large value of OHC in bulk MoS2 makes our device competitive in terms of energetic efficiency and could be integrated in TMD heterostructures to design memory devices with multiple magnetization states for non-Boolean computation.

Furthermore, the intrinsic orbital-Hall conductivity is predicted to be huge, which is the driving force behind the observed differential voltage. p. 4
Where the paper says it

Resistivity measurements (see Supplementary Information) show that our MoS₂ sample is a non-degenerate n-type semiconductor, thus we expect that the reference Fermi energy falls within the upper part of the MoS₂ conduction bandgap, where SHC is absent. This result gives a strong assessment to the scenario where, at least at the intrinsic level, orbital current is by far and large, the driving force behind the differential voltage observed in the device.

Switching Dynamics and Control

The switching process is characterized by a deterministic behavior controlled by current sign and field sign. The hysteresis measured with above-threshold currents shows jumps in the descending H branches, indicating that the irreversible switching is driven by the applied current. p. 2

Where the paper says it

In absence of this effect, Vdiff would not be altered since any direct spin flow between the electrodes and across MoS2 is ruled out by the distance of the electrodes (tens m), which by far exceeds any realistic spin-diffusion length in MoS2. Most importantly, while the spin-valve hysteresis measured with sub-threshold currents, with jumps in the ascending |H| branches, is driven by the applied field, the hysteresis measured with above-threshold currents, with jumps in the descending |H| branches, must be necessarily driven by the applied current.

The switching threshold current is identified as Ipeak=1. p. 3
Where the paper says it

This means that zero or low fields (< 50 Oe) do not influence the irreversible current-induced switching, which is only determined by the sign of the applied current, as long as it is above a threshold value. On the contrary, at fields H=100 Oe - that is for fields larger than the switching field H= 50 Oe identified in the hysteresis H cycles of Fig.

6 mA in zero field, corresponding to a switching current density of 1. p. 6
Where the paper says it

As a consequence, the two magnetization states can be switched back and forth by a zero-field switching current Ipeak1. 6 mA, corresponding to a switching current density 3.

6x104 A/cm2. p. 3
Where the paper says it

6 mA as the switching current, corresponding to switching current density 1. 6x104 A/cm2 .

The deterministic switching occurs even in zero field and for low fields (< 50 Oe) as long as the applied current is above the threshold value. p. 3
Where the paper says it

It can be also noted that these hysteresis loops at zero field and at H=25 Oe are all cycled in the same direction, as indicated by the arrows. This means that zero or low fields (< 50 Oe) do not influence the irreversible current-induced switching, which is only determined by the sign of the applied current, as long as it is above a threshold value.

Material Platform Potential

The work emphasizes that the platform of Van der Waals materials is ideal for developing unconventional non-Boolean memory devices for neuromorphic computation. The family of Van der Waals materials includes countless high spin-orbit dichalcogenides, in which charge-tospin conversion mechanisms generate spin currents with both out-of-plane and in-plane spin polarizations. p. 7

Where the paper says it

Our device is based on the semiconducting Van der Waals MoS2 dichalcogenide, whose OHE is predicted by our theoretical calculations to be sizeable. The family of Van der Waals materials includes countless high spin-orbit dichalcogenides, in which charge-tospin conversion mechanisms generate spin currents with both out-of-plane and in-plane spin polarizations.

Moreover, many two-dimensional Van der Waals ferromagnetic compounds exist, such as Fe3GeTe2 and Fe3GaTe2, with either in-plane or out-of-plane anisotropy and large Curie temperatures. p. 7
Where the paper says it

The family of Van der Waals materials includes countless high spin-orbit dichalcogenides, in which charge-tospin conversion mechanisms generate spin currents with both out-of-plane and in-plane spin polarizations. Moreover, many two-dimensional Van der Waals ferromagnetic compounds exist, such as Fe3GeTe2, Fe3GaTe2, CrI3 and CrT2, with either in-plane or out-of-plane anisotropy and large Curie temperatures, even up to room temperature.

Experimental Validation

The experimental setup involved MoS2 of 50 nm thickness and hexagonal BN (h-BN) of 10 nm thick flakes transferred deterministically on Si/SiO2 substrates. Measurements were carried out at room temperature, applying an AC or DC current to the MoS2 flake and measuring voltage at the Cobalt electrodes. p. 7

Where the paper says it

Patterning of Ti(10 nm)/Au(100 nm) electrodes for current injection and Co(25nm) electrodes for spin valves were realized on the top of the heterostacks by electron beam lithography and sputtering (Ti/Au) and e-beam evaporation (Co). Measurements were carried out at room temperature, applying an AC or DC current to the MoS2 flake and measuring voltage at the Cobalt electrodes.

p. 7
Where the paper says it

Patterning of Ti(10 nm)/Au(100 nm) electrodes for current injection and Co(25nm) electrodes for spin valves were realized on the top of the heterostacks by electron beam lithography and sputtering (Ti/Au) and e-beam evaporation (Co). Measurements were carried out at room temperature, applying an AC or DC current to the MoS2 flake and measuring voltage at the Cobalt electrodes.

The analysis confirmed that only the orbital-Hall conductivity can be sizeable in the band gap of MoS2, as spin-Hall conductivity must vanish. p. 7
Where the paper says it

Concerning the fundamental interpretation of the observed phenomenon, highly accurate ab-initio results assess that the vertical Hall current generated in MoS₂, which accumulates at the interface is, in fact, not a spin-Hall current but an orbital-Hall current. We emphasize the incontrovertible soundness of our result: for a semiconductor like MoS₂, only the orbital-Hall conductivity can be sizeable in the band gap, since the spin-Hall conductivity must vanish.

The device's working principles could be applied to vertical geometries for miniaturization and scalability.

Conclusion

In this work we present a novel spintronic device capable of field-free deterministic switching at room temperature, using writing current densities as low as 3.2x104 A/cm2. p. 0

Where the paper says it

We demonstrate that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3. 2x104 A/cm2 even in zero field, owed to a tilted geometry and a differential voltage architecture.

The switch between two stable inplane magnetic states is achieved through an original design that combines spin-valve and spin-torque concepts for reading and writing operations. p. 6
Where the paper says it

2x104 A/cm2 . The switch between two stable inplane magnetic states is achieved through an original design that combines spin-valve and spin-torque concepts for reading and writing operations, respectively.

Two aspects characterize most effectively our design: (ii) the differential character of the output voltage measured between two magnetic electrodes with different shape anisotropy, and (ii) the tilt of the local electric current by an angle α with respect to the easy magnetization axis of the anisotropic electrode, which allows the easy switch between aligned and misaligned electrode magnetization states. p. 7
Where the paper says it

design: (ii) the differential character of the output voltage measured between two magnetic electrodes with different shape anisotropy, and (ii) the tilt of the local electric current by an angle  with respect to the easy magnetization axis of the anisotropic electrode, which allows the easy switch between aligned and misaligned electrode magnetization states. While our prototype is implemented in planar geometry, the working principles could be applied to vertical geometries, to comply with miniaturization and scalability issues required for large-scale fabrication and commercialization.

The authors conclude that in our device, the specific direction of each magnetization does depend on the directions of the applied field and current, as well as on the field and current direction of the previous cycle, as long as these fields and currents exceed the respective magnetization-pinning threshold values. p. 6
Where the paper says it

2x104 A/cm2 that is more than one order of magnitude smaller than the 106 A/cm2 values measured in SOT devices based on TMDs and topological insulators [1,2,10,11,41,42,43,44] and three times smaller than the 105 A/cm2 value measured in a SOT device based on TaIrTe4 [ 45]. On the other hand, in our device the specific direction of each magnetization does depend on the directions of the applied field and current, as well as on the field and current direction of the previous cycle, as long as these fields and currents exceed the respective magnetization-pinning threshold values For this reason an initialization magnetization protocol should be used, with maximum field and current applied, to fix a given initial configuration of magnetizations, and thus establish the polarity of the current that must be applied to switch deterministically the state.

Experimental Methods

MoS2 flakes were obtained by mechanical exfoliation from single crystals and transferred deterministically on Si/SiO2 substrates. The room temperature resistivity, carrier density and mobility of the MoS2 flake are 3. p. 7

Where the paper says it

Experimental methods MoS2 of 50 nm thickness and hexagonal BN (h-BN) 10 nm thick flakes were obtained by mechanical exfoliation from single crystals and transferred deterministically on Si/SiO2 substrates. The room temperature resistivity, carrier density and mobility of the MoS2 flake are 3.

5x10-4 Ωm, 10 18 cm-3 and 150 cm 2/(Vs), respectively. p. 7
Where the paper says it

The room temperature resistivity, carrier density and mobility of the MoS2 flake are 3. 5x10-4 m, 1018 cm-3 and 150 cm2 /(Vs), respectively, and the resistivity has a semiconducting temperature behaviour with thermal activation energy 80 meV (see Supplementary Information).

Patterning of Ti(10 nm)/Au(100 nm) electrodes for current injection and Co(25nm) electrodes for spin valves were realized on the top of the heterostacks by electron beam lithography and sputtering (Ti/Au) and e-beam evaporation (Co). p. 7
Where the paper says it

MoS2/h-BN heterostack based devices were fabricated. Patterning of Ti(10 nm)/Au(100 nm) electrodes for current injection and Co(25nm) electrodes for spin valves were realized on the top of the heterostacks by electron beam lithography and sputtering (Ti/Au) and e-beam evaporation (Co).

Measurements were carried out at room temperature, applying an AC or DC current to the MoS2 flake and measuring voltage at the Cobalt electrodes.

Computational Methods

Spin Hall conductivities (SHC) σSH and orbital Hall conductivities (OHC) σOH were calculated within the linear response theory by the Kubo formula. An accurate evaluation of SHC and OHC requires that the summation in Eq. p. 8

Where the paper says it

Computational methods Spin Hall conductivities (SHC) SH and orbital Hall conductivities (OHC) OH were calculated within the linear response theory by the Kubo formula[4 ]: σzx,SH(OH) y = e ℏ ∑ ∫ fnkΩn Qy (k) d 3𝑘 (2π) 𝑛 3 (1) Ωn Qy (k) = 2ℏ 2 ∑ Im [ <unk|jz Qy |umk><umk|vx|unk> (Enk−Emk+iη) 2 m≠n ] (2) where fnk is the Fermi-Dirac distribution function, < unk > is the periodic part of the Bloch state, whose energy eigenvalue is Enk, vx is the x component of the velocity operator, and j z Qy is the z component of the orbital(spin) current operator J z Qy = (Qy vz + vz Qy)/2, with y component of the orbital(spin) angular momentum Q = Ly(Sy). An accurate evaluation of SHC and OHC requires that the summation in Eq.

(1) be performed on a very dense k-mesh. p. 8
Where the paper says it

An accurate evaluation of SHC and OHC requires that the summation in Eq. (1) be performed on a very dense k-mesh.

The electronic structure was obtained from ab initio calculations based on the density functional theory and using projector-augmented wave pseudopotentials. p. 8
Where the paper says it

To avoid cumbersome ab initio calculation we made use of the Wannier interpolation technique to compute the Berry curvature term in Eq (2) on arbitrary k-points in an effortless way. The electronic structure was obtained from ab initio calculations based on the density functional theory and using projector-augmented wave pseudopotentials [46 , 47] as implemented in the VASP package [48 , 49].

Summary of Findings

The single most informative sentence about the paper's subject and finding is that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3.2x104 A/cm2 even in zero field. p. 0

Where the paper says it

We demonstrate that stable voltage states at room temperature can be deterministically controlled by a switching current density as low as 3. 2x104 A/cm2 even in zero field, owed to a tilted geometry and a differential voltage architecture.

This result stems from the exploitation of orbital angular momentum in place of spin, where the huge intrinsic orbital-Hall effect is the dominant driving force behind the observed differential voltage. p. 4
Where the paper says it

This result gives a strong assessment to the scenario where, at least at the intrinsic level, orbital current is by far and large, the driving force behind the differential voltage observed in the device. We remark, however, that the SHC is particularly small for the out-of-plane spin current orientation, while for planar directions (see a complete account in the Supplementary Information) it is sizeable in the vicinity of band extrema, albeit nowhere near the OHC values.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Enhanced memory device design can utilize a novel MoS2-based architecture where the SOT is exerted not on a single electrode (as in conventional SOT architectures), but simultaneously on two Co electrodes with inplane magnetization and different shape anisotropy. This allows for deterministic switching between two stable states, ‘0’ and ‘1’.

  2. The system can achieve field-free deterministic switching at room temperature using writing current densities as low as 3.2x104 A/cm2, which is more than one order of magnitude smaller than the 10 6 A/cm2 values measured in SOT devices based on TMDs and topological insulators.

  3. The device's operation can be controlled by two key aspects: "the differential character of the output voltage measured between two magnetic electrodes with different shape anisotropy, and (ii) the tilt of the local electric current by an angle alpha with respect to the easy magnetization axis of the anisotropic electrode."

  4. The system can perform non-perturbative reading of states using sub-threshold currents, as reading currents well below the threshold (e.g. Ipeak=0.4 mA or smaller) are recommended, provided that the signal to noise ratio allows to appreciate the 1 microvolt difference between the two voltages states.

  5. The underlying physical mechanism can be accurately modeled using ab-initio calculations showing that orbital current is by far and large, the driving force behind the differential voltage observed in the device, which is attributed to a huge intrinsic orbital-Hall effect in MoS2.

Abstract

Charge-to-spin and spin-to-charge conversion mechanisms in high spin-orbit materials are the new frontier of memory devices. They operate via spin-orbit torque (SOT) switching of a magnetic electrode, driven by an applied charge current. In this work, we propose a novel memory device based on the semiconducting two-dimensional centrosymmetric transition metal dichalcogenide (TMD) MoS2, that operates as a SOT device in the writing process and as a non-local spin valve in the reading process. We demonstrate that stable voltage states at room temperature can be controlled by applied current and magnetic fields, owed to a locally tilted geometry and a differential voltage architecture. Ab initio calculations of orbital Hall effect (OHE) and spin Hall effect (SHE) indicate that the orbital Hall conductivity is constant and sizeable (750x(hbar/e) ohm-1 cm-1) throughout the conduction gap, while the spin Hall conductivity vanishes in the gap, thus pointing to the former as the most likely responsible for the generation of the SOT in the magnetic electrode, among intrinsic mechanisms. However, also extrinsic and interface spin-orbit mechanisms likely play a role. Our device concept may be competitive in terms of energy efficiency if an acceptable trade off with stability is obtained.

Sources

Related papers