Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

arXiv:2306.08091 · physics.flu-dyn, cs.SY, eess.SY · Submitted 2023-05-01 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: We're looking at the paper: "Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation".

Mira: Here's the gist of the paper. The paper presents the development of a novel bio-inspired hydrofoil system for detecting and characterizing ocean currents and waves based on a dolphin’s flipper foil design.

Kai: This system shows potential for use in various marine applications, including oceanographic research, environmental monitoring, and navigation.

Mira: Bio-inspired Design Rationale The system is modeled after the superficial neuromast of an aquatic vertebrate.

Kai: The rationale for using this model is that if one treats the aquatic vertebrate as a bluff body, i.e.

Title and authors: Kai: So, what does the paper actually propose this system is capable of doing? It’s designed to be a standalone data acquisition system that can characterize currents and particle trajectories caused by gravity waves.

Mira: They use hot-wire anemometers fitted in each rectangular slot on the fin platform for this characterization work. The process starts with moving the fin to a zero position of ninety degrees and reading those anemometers into a micro-controller.

Lev: Reading those sensors is one thing, but what’s the actual detection threshold they set up? Because in real hardware, you need that specific measurement to trigger anything useful.

Kai: They take a percent difference between readings, and if that difference is below some threshold value—specifically five percent—they consider themselves aligned in the dominant direction of flow.

Mira: That five percent threshold sounds like a way to define what counts as "aligned" versus just noisy data in this specific setup. It’s about establishing a reliable flow-orientation scheme using these sensors.

Lev: But what about estimating the actual physical wave parameters, like wave height and current speed? That sounds more complex than just checking if they are aligned or not.

Kai: To get those hydrodynamic parameters, like wave height and current speed, they have to use small-amplitude wave theory, which is linearized wave theory. They use a linear dispersion relationship that involves the term sigma squared g equal k times tanh of k times h times k.

Mira: And for estimating particle trajectories, they employ small angle theory to derive the flow at the stagnation point from one of the regions along this streamlined body. That proof applies regardless of any known mounting distance from that stagnation point.

The paper's summary: Kai: Moving into the experimental results, what did they actually measure when they validated this prototype? They calibrated their anemometers and found a percent difference with no flow speed of approximately one point seven two percent.

Mira: And they noted that the two anemometers had resting voltages of zero point five eight volts and zero point five nine volts, respectively. That’s the kind of noise you have to deal with when you start measuring things in the real world.

Lev: So, despite that measurement error, what was the system's actual performance in terms of movement? How quickly could it react?

Kai: The foil was able to quickly and consistently move to a new location and maintain its position until a new flow direction was encountered. They measured the rise and fall time of the foil heading as approximately forty degrees per second with that servo motor.

Mira: Forty degrees per second sounds like a pretty fast response time for maneuvering, especially considering it’s tied to reading those hot-wire anemometers and adjusting the servo motor.

Lev: That speed is important for real applications, but they also flagged some limitations in their setup. What did the authors say they might still need to work on?

Kai: They noted that there are limitations with the equipment utilized, and they mentioned a further need to incorporate Direct-Memory-Access protocols into their software.

Mira: So, while the physical movement worked well, the software side—how fast it can actually process all that collected data—is where they see room for improvement in terms of efficiency.

The paper's improvements: Kai: So to wrap up on this paper, the bio-inspired hydrofoil system presents a promising approach for characterizing ocean currents and waves through its design based on a dolphin's flipper foil. It shows potential for oceanographic research, environmental monitoring, and navigation applications.

Mira: The main implication is that you can use this physical setup to estimate wave height and current using the foil’s positioning based on wave mechanics and a geometric proof.

Lev: I think the key thing here is that while the prototype worked consistently in terms of movement, they still need to focus on refining those variable sampling rates for better data processing efficiency.

Kai: And implementing those Direct-Memory-Access protocols will help increase the efficiency of their data acquisition process significantly.

Mira: Ultimately, further testing in real ocean environments is necessary to validate the system’s performance under more complex and dynamic conditions than what they tested in the lab.

Lev: I think it’s a solid starting point for an AUV system, but getting that processing efficiency dialed in is where you turn a prototype into something useful for real missions.

Kai: So, we've looked at how this bio-inspired hydrofoil system works and what its potential is for ocean monitoring and navigation. That’s all on this paper from "Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation".

Conclusion: Kai: So we’ve looked at how this bio-inspired hydrofoil system is being built to detect ocean currents and waves, based on a dolphin's flipper design and modeling that superficial neuromast.

Mira: Exactly, it’s designed to be a standalone data acquisition system capable of characterizing those currents and particle trajectories caused by gravity waves.

Lev: So the core idea is treating the aquatic vertebrate as a bluff body, like an ellipsoid shape, and aligning it parallel to the flow minimizes the lift force needed for movement.

Kai: That’s what they modeled—if you align it right with the flow direction, you get a minimum lift force, which should help reduce power consumption for an autonomous underwater vehicle.

Mira: The detection mechanism uses hot-wire anemometers in each slot on the fin platform to read flow speed, and they define alignment by checking if the percent difference between readings is below a threshold of five percent.

Lev: I mean, reading those sensors is one thing, but what about getting that actual wave height and current estimation you need for oceanographic research?

Kai: They use small-amplitude wave theory—linearized wave theory—to get hydrodynamic parameters like wave height and current speed. They use a linear dispersion relationship involving sigma squared g equals k times tanh of k times h times k.

Mira: And they also use small angle theory to derive the flow at the stagnation point from one of the regions along that streamlined body, which applies no matter how far away you are from that point.

Lev: Experimentally, they found a percent difference with no flow speed of about one point seven two percent between their two anemometers. That’s a measurement error we have to account for when you try to run this on real hardware.

Kai: But the foil moved quickly and consistently to new locations and held its position until it hit a new flow direction, showing a rise and fall time of about forty degrees per second with the servo motor.

Mira: That response time is pretty fast for maneuvering, but they also flagged limitations, saying there’s still room to improve things with variable sampling rates and implementing Direct-Memory-Access protocols in the software.

Lev: So it moves well enough for a prototype, but you need better software efficiency and real ocean testing to see if it’s robust enough for actual deployment.

Kai: It’s a promising approach for ocean current and wave characterization, based on the full paper "Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation".

Mira: It offers potential to significantly impact marine applications if they can refine those data acquisition processes.

Lev: I think the next step is really pushing that processing efficiency so it can handle more complex, dynamic flow conditions out there.

Brendan M. Unikewicz

University of Rhode Island · Massachusetts Institute of Technology

physics.flu-dyn, cs.SY, eess.SY

Submitted: 2023-05-01

Updated: 2026-11-09

Comments: Is not representative of my best work; submitted too early.

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 78/100

The gist: The paper presents the development of a novel bio-inspired hydrofoil system for detecting and characterizing ocean currents and waves based on a dolphin’s flipper foil design.

Key concepts

Bio-inspired Design Rationale
The design mimics the superficial neuromast of a dolphin's flipper. The rationale suggests that if an aquatic vertebrate aligns itself parallel to the flow, it minimizes lift force. This principle is applied to AUV systems to aim for better positioning and reduced power consumption during operations.
Flow Detection Mechanism
The hydrofoil acts as a data acquisition system using hot-wire anemometers in slots. By measuring percent differences between readings from different slots, the system identifies the dominant direction of flow with high accuracy, allowing the foil to orient itself correctly.
Wave Parameter Estimation
Linearized wave theory is used to estimate hydrodynamic parameters like wave height and current. This involves using geometric proofs based on small-angle theory applied to particle trajectories near the foil's stagnation point to derive flow characteristics from its position.

Terminology

Summary

The paper presents the development of a novel bio-inspired hydrofoil system for detecting and characterizing ocean currents and waves based on a dolphin’s flipper foil design. p. 0

Where the paper says it

Unikewicz∗ Department of Ocean Engineering University of Rhode Island Narragansett, RI, 02882 May 1, 2023 ABSTRACT Ocean dynamics play a crucial role in global climate, ecosystems, and human activities, necessitating accurate and efficient methods to characterize ocean currents and waves. This paper presents the development of a novel bio-inspired hydrofoil system for detecting and characterizing ocean currents and waves based on a dolphin’s flipper foil design.

This system shows potential for use in various marine applications, including oceanographic research, environmental monitoring, and navigation. p. 0
Where the paper says it

Wave mechanics and a geometric proof were applied to estimate wave parameters such as wave height and current from the hydrofoil’s positioning. The proposed hydrofoil system shows potential for use in various marine applications, including oceanographic research, environmental monitoring, and navigation.

Bio-inspired Design Rationale

The system is modeled after the superficial neuromast of an aquatic vertebrate. The rationale for using this model is that if one treats the aquatic vertebrate as a bluff body, i. p. 1

Where the paper says it

We will be modeling our work after the superficial neuromast, a discrete sensor located flush with the boundary of the foil. If we treat the aquatic vertebrate as a bluff body, i. p. 1

Where the paper says it

We will be modeling our work after the superficial neuromast, a discrete sensor located flush with the boundary of the foil. If we treat the aquatic vertebrate as a bluff body, i.

e. an ellipsoid shape, and the vertebrate chooses to align itself parallel to the direction of flow then the lift force exerted on the body is a minimum. p. 1
Where the paper says it

If we treat the aquatic vertebrate as a bluff body, i. an ellipsoid shape, and the vertebrate chooses to align itself parallel to the direction of flow then the lift force exerted on the body is a minimum, reducing the amount of power required to move in a singular direction.

This rationale of thinking may be directly translated towards AUV systems and we can expect to see better mission run positioning, tracking, and decreased power consumption through multiple operations. p. 1
Where the paper says it

an ellipsoid shape, and the vertebrate chooses to align itself parallel to the direction of flow then the lift force exerted on the body is a minimum, reducing the amount of power required to move in a singular direction. This rationale of thinking may be directly translated towards AUV systems and we can expect to see better mission run positioning, tracking, and decreased power consumption through multiple operations.

The paper reviews the theory as to why flow-orientation schemes provide decreased power consumption in AUVs. p. 1
Where the paper says it

Through the smart hydrofoil proposed in this paper, only one foil is required for decreasing power requirements in AUVs with the additional advantage of characterizing surface conditions at or near the upper ocean layer. This paper reviews the theory as to why flow-orientation schemes provide decreased power consumption in AUVs, validation of an in-air prototype for potential wave tank testing, and the mathematical formulation for and design of a hydrofoil capable of acting as a standalone DAQ system to characterize currents and particle trajectories induced by gravity waves.

Flow Detection Mechanism

The hydrofoil is designed to be a standalone Data Acquisition (DAQ) system capable of characterizing currents and particle trajectories induced by gravity waves. The design utilizes hot-wire anemometers fitted in each rectangular slot on the fin platform. p. 2

Where the paper says it

The cross-shaped exclusion indicates where the servo motor is fitted, in-line with the center of gravity. Hot-wire anemometers fit in each rectangular slot on the fin platform and wires are funneled through the trailing edge.

The DAQ software begins by moving the fin to a zero position of 90° and reading the anemometers into the micro-controller. p. 3
Where the paper says it

With the anemometers and a single servo motor, we can now describe code, in C/C++, to archive data as well as reorient our hydrofoil. 3 DAQ Software Design The DAQ software for the hydrofoil begins by moving the fin to a zero position of 90°.

A percent difference is taken, and if it is below some threshold value, i. p. 3
Where the paper says it

Once approximately 10 seconds has passed, allowing the temperature dependent resistors to stabilize, the anemometers, located symmetrically on opposite sides of the fin platform, are read into the micro-controller as an analog value and a percent difference is taken. For our validation, if the percent difference is below some threshold value, i.

e. 5%, then we are currently aligned in the dominant direction of flow. p. 3
Where the paper says it

For our validation, if the percent difference is below some threshold value, i. 5%, then we are currently aligned in the dominant direction of flow and the sample rate remains a constant value of 2 Hz.

Wave Parameter Estimation

To obtain hydrodynamic parameters such as wave height and current, small–amplitude wave theory, i.e. linearized wave theory, must be used. p. 5

Where the paper says it

1 Application of Wave Mechanics To obtain hydrodynamic parameters such as wave height and current, small–amplitude wave theory, i. linearized wave theory, must be used.

The linear dispersion relationship is given by σ2g = ktanh(kh). p. 5
Where the paper says it

u = ∇ϕ (3) ∇2ϕ = 0 (4) ∂ϕ ∂t + 1 2 |u| 2 + gz + p ρ = 0 (5) Small surface elevations and fluid velocities, constant atmospheric pressure, and water depth at the survey site permit the use of the linear dispersion relationship for our data acquisition system. σ 2 g = ktanh(kh) (6) 6

Geometric proof for particle trajectory estimation uses small angle theory to derive flow at the stagnation point from one of the regions along the streamlined body. p. 6
Where the paper says it

2 Geometric Proof for Particle Trajectory Estimation It’s possible to derive flow at the stagnation point from one of the regions along the streamlined body; however, that would be computationally intensive, most likely requiring numerical modeling to relate the measured current to the actual current at or near the stagnation point or even the integration of additional sensors, which would increase the operational power required. Since we have our future motor with a known angle, Θ, located at a known distance from the stagnation point, G, we can use simple geometry and a time-scale to resolve the vertical position, r, and vertical component of ocean currents, w, induced by gravity waves [Fig.

This proof applies to any known mounting distance from the stagnation point. p. 6
Where the paper says it

Figure 4: Proposed wave estimation diagram for a flow-orienting fin mounted to an AUV for deep-water ocean waves. The following proof applies to any known mounting distance from the stagnation point.

Prototype Validation and Limitations

The experimental results showed that after calibrating the anemometers, they exhibit a percent difference, with no flow speed, of approximately 1.72% with anemometer one having a resting voltage of 0. p. 4

Where the paper says it

2 Experimental Results After calibrating the anemometers, we see they exhibit a percent difference, with no flow speed, of approximately 1. 72% with anemometer one having a resting voltage of 0.

58 volts and anemometer two with 0. p. 4
Where the paper says it

72% with anemometer one having a resting voltage of 0. 58 volts and anemometer two with 0.

59 volts. The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. p. 4
Where the paper says it

The position of the hydrofoil depicts a clear story of what was occurring within the system, moving to positions of approximately 90°, 140°, 105°, 60°, 150°, 105°, 150°, and 130°throughout time. The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig.

Limitations do exist with the equipment utilized, and there may further be a need to incorporate Direct-Memory-Access protocols into our software. p. 4
Where the paper says it

Improvement to this data may take the form of decreasing the threshold that was used or swapping out the hardware for more precise components. Limitations do exist with the equipment utilized, and there may further be a need to incorporate Direct-Memory-Access protocols into our software, working only from memory to peripheral.

The system's ability to process the collected data is expected to greatly increase the performance of existing fin-type propulsion systems.

Conclusion and Future Work

In conclusion, the bio-inspired hydrofoil system presents a promising approach for ocean current and wave characterization. While the initial prototype showed promising results, some areas of improvement were identified, such as refining the variable sampling rate and implementing Direct-Memory-Access protocols to increase the efficiency of the data acquisition process. p. 7

Where the paper says it

This method has the potential to be utilized in various oceanic environments, from deep to shallow water, providing valuable data for various marine applications such as oceanographic research, environmental monitoring, and navigation. While the initial prototype showed promising results, some areas of improvement were identified, such as refining the variable sampling rate and implementing Direct-Memory-Access protocols to increase the efficiency of the data acquisition process.

Additionally, further testing in real ocean environments is necessary to validate the system’s performance under more complex and dynamic conditions. p. 7
Where the paper says it

While the initial prototype showed promising results, some areas of improvement were identified, such as refining the variable sampling rate and implementing Direct-Memory-Access protocols to increase the efficiency of the data acquisition process. Additionally, further testing in real ocean environments is necessary to validate the system’s performance under more complex and dynamic conditions.

The bio-inspired hydrofoil system offers a promising approach to ocean current and wave characterization, with the potential to significantly impact marine applications. p. 0
Where the paper says it

The proposed hydrofoil system shows potential for use in various marine applications, including oceanographic research, environmental monitoring, and navigation. The bio-inspired hydrofoil system offers a promising approach to ocean current and wave characterization, with the potential to significantly impact our understanding and monitoring of ocean dynamics without greatly impacting vehicle performance or increasing power utilization in operation.

References

Avilash Sahoo, Santosha K. Dwivedy, and P. p. 7

Where the paper says it

References Avilash Sahoo, Santosha K. Dwivedy, and P.

S. Robi. Advancements in the field of autonomous underwater vehicle. p. 7
Where the paper says it

Dwivedy, and P. Advancements in the field of autonomous underwater vehicle.

Arie Sukma Jaya and Muljo Widodo Kartidjo. p. 7

Where the paper says it

com/science/article/pii/S0029801819301623. Arie Sukma Jaya and Muljo Widodo Kartidjo.

Thrust and efficiency enhancement scheme of the fin propulsion of the biomimetic autonomous underwater vehicle model in low-speed flow regime. p. 7
Where the paper says it

Arie Sukma Jaya and Muljo Widodo Kartidjo. Thrust and efficiency enhancement scheme of the fin propulsion of the biomimetic autonomous underwater vehicle model in low-speed flow regime.

Yuhong Liu, Houcun Li, Shihan Deng, Shuxin Wang, Shuhe Liu, and Zhijie Wang. p. 7

Where the paper says it

com/ science/article/pii/S0029801821014177. Yuhong Liu, Houcun Li, Shihan Deng, Shuxin Wang, Shuhe Liu, and Zhijie Wang.

Biomimetic robotic sea lion foreflippers: Design, modeling, and experimentation. p. 7
Where the paper says it

Yuhong Liu, Houcun Li, Shihan Deng, Shuxin Wang, Shuhe Liu, and Zhijie Wang. Biomimetic robotic sea lion foreflippers: Design, modeling, and experimentation.

Yonggang Jiang, Zhiqiang Ma, and Deyuan Zhang. p. 7

Where the paper says it

1109/TMECH. Yonggang Jiang, Zhiqiang Ma, and Deyuan Zhang.

Flow field perception based on the fish lateral line system. p. 7
Where the paper says it

Yonggang Jiang, Zhiqiang Ma, and Deyuan Zhang. Flow field perception based on the fish lateral line system.

Jacqueline F Webb, Karen P Maruska, Julie M Butler, and Margot AB Schwalbe. p. 7

Where the paper says it

Bioinspiration & biomimetics, 14(4):041001, 2019. Jacqueline F Webb, Karen P Maruska, Julie M Butler, and Margot AB Schwalbe.

The mechanosensory lateral line system of cichlid fishes: from anatomy to behavior. p. 7
Where the paper says it

Jacqueline F Webb, Karen P Maruska, Julie M Butler, and Margot AB Schwalbe. The mechanosensory lateral line system of cichlid fishes: from anatomy to behavior.

Hanumant Singh, Dana Yoerger, and Albert Bradley. p. 8

Where the paper says it

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation Hanumant Singh, Dana Yoerger, and Albert Bradley. Issues in auv design and deployment for oceanographic research.

Issues in auv design and deployment for oceanographic research. p. 8
Where the paper says it

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation Hanumant Singh, Dana Yoerger, and Albert Bradley. Issues in auv design and deployment for oceanographic research.

Paul S Granville. p. 8

Where the paper says it

IEEE, 1997. Paul S Granville.

Elements of the drag of underwater bodies. p. 8
Where the paper says it

Paul S Granville. Elements of the drag of underwater bodies.

Richard Evelyn Donohue Bishop and AY Hassan. p. 8

Where the paper says it

Technical report, DAVID W TAYLOR NAVAL SHIP RESEARCH AND DEVELOPMENT CENTER BETHESDA MD SHIP . Richard Evelyn Donohue Bishop and AY Hassan.

The lift and drag forces on a circular cylinder oscillating in a flowing fluid. p. 8
Where the paper says it

Richard Evelyn Donohue Bishop and AY Hassan. The lift and drag forces on a circular cylinder oscillating in a flowing fluid.

B. Mutlu Sumer and Jørgen Fredsøe. p. 8

Where the paper says it

Mathematical and Physical Sciences, 277(1368):51–75, 1964. Mutlu Sumer and Jørgen Fredsøe.

Hydrodynamics around cylindrical structures. p. 8
Where the paper says it

Mutlu Sumer and Jørgen Fredsøe. Hydrodynamics around cylindrical structures.

A. E. Perry and G. p. 2

Where the paper says it

Constant temperature anemometers contain two fixed resistors, R1 and R2, a temperature dependent resistor, Rw, and lastly a variable resistor, R3, to bring the bridge back into balance. As flow passes over the temperature dependent resistor the unbalancing of the resistor bridge results in a voltage difference, which is compensated through the current in the system [Perry and Morrison].

L. Morrison. A study of the constant-temperature hot-wire anemometer. p. 8
Where the paper says it

Perry and G. A study of the constant-temperature hot-wire anemometer.

Enders Robinson and Dean Clark. p. 8

Where the paper says it

1017/S0022112071001241. Enders Robinson and Dean Clark.

Sampling and the nyquist frequency. p. 3
Where the paper says it

Additionally, the variable sampling rate is a key factor in this system due to the availability of power and the ability of the foil to characterize multi-frequency waves. In an ocean environment waves are not monochromatic, and at a minimum the Nyquist frequency must be satisfied to characterize the highest frequency encountered [Robinson and Clark]; however, it will be necessary to increase the sampling rate further, 10-20x the Nyquist frequency, in order to fully characterize the particle trajectory motions.

John Nicholas Newman. p. 8

Where the paper says it

The Leading Edge, 10(3):51–53, 1991. John Nicholas Newman.

Marine hydrodynamics. p. 8
Where the paper says it

John Nicholas Newman. Marine hydrodynamics.

--- Page 1 ---

DESIGN AND FORMULATION OF A HYDROMECHANICAL FIN FOR AUV OPERATIONS AND WAVE PARAMETER ESTIMATION

Brendan M. Unikewicz∗

Department of Ocean Engineering

University of Rhode Island

Narragansett, RI, 02882

--- Page 2 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation of flow. We will be modeling our work after the superficial neuromast, a discrete sensor located flush with the boundary of the foil. p. 1

Where the paper says it

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation of flow. We will be modeling our work after the superficial neuromast, a discrete sensor located flush with the boundary of the foil.

If we treat the aquatic vertebrate as a bluff body, i.e. an ellipsoid shape, and the vertebrate chooses to align itself parallel to the direction of flow then the lift force exerted on the body is a minimum, reducing the amount of power required to move in a singular direction. p. 1
Where the paper says it

If we treat the aquatic vertebrate as a bluff body, i. an ellipsoid shape, and the vertebrate chooses to align itself parallel to the direction of flow then the lift force exerted on the body is a minimum, reducing the amount of power required to move in a singular direction.

This does offer the question as to why we do not explore the integration of discrete sensors along the body of an AUV as opposed to the intended hydrofoil. p. 1
Where the paper says it

This rationale of thinking may be directly translated towards AUV systems and we can expect to see better mission run positioning, tracking, and decreased power consumption through multiple operations. This does offer the question as to why we do not explore the integration of discrete sensors along the body of an AUV as opposed to the intended hydrofoil.

--- Page 3 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

Assuming we have an approximately constant flow field for the top and bottom of our fin platform, in the vertical plane (x- and z-axis), and apply mass conservation laws, we know that the amount of fluid passing over the top of the structure is equivalent to the amount of fluid passing underneath. In potential flow theory, this applies to all angle–of–attacks, and you could calculate the lift force. p. 2

Where the paper says it

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation Assuming we have an approximately constant flow field for the top and bottom of our fin platform, in the vertical plane (x- and z-axis), and apply mass conservation laws, we know that the amount of fluid passing over the top of the structure is equivalent to the amount of fluid passing underneath. In potential flow theory, this applies to all angle–of–attacks, and you could calculate the lift force; however, we want to utilize the resulting disparity in flow speed to reorient ourselves in the mean, dominant direction of flow as well as characterize particle trajectories at the upper ocean layer.

p. 2
Where the paper says it

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation Assuming we have an approximately constant flow field for the top and bottom of our fin platform, in the vertical plane (x- and z-axis), and apply mass conservation laws, we know that the amount of fluid passing over the top of the structure is equivalent to the amount of fluid passing underneath. In potential flow theory, this applies to all angle–of–attacks, and you could calculate the lift force; however, we want to utilize the resulting disparity in flow speed to reorient ourselves in the mean, dominant direction of flow as well as characterize particle trajectories at the upper ocean layer.

--- Page 4 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

For determining the dominant direction of flow in the prototype, we can ignore the inertial and Froude-Krylov contributions towards Morison’s equation. At an angle of attack of zero degrees (and depending on the foil parameters) the coefficient of lift will be nearly zero. p. 1

Where the paper says it

Additionally, the added forces in Morison’s equation for a moving body in an oscillatory flow only provide an estimate of the variation about the mean value that we are concerned with. At an angle of attack of zero degrees (and depending on the foil parameters) the coefficient of lift will be nearly zero.

If we were to use the lift force along the body, a nonlinear function of the current velocity, the minimum value would indicate the foil is aligned in the dominant direction of flow and maximally reduce the lift force. p. 1
Where the paper says it

At an angle of attack of zero degrees (and depending on the foil parameters) the coefficient of lift will be nearly zero. If we were to use the lift force along the body, a nonlinear function of the current velocity, the minimum value would indicate the foil is aligned in the dominant direction of flow and maximally reduce the lift force; however, we can use even more simplified assumptions.

--- Page 5 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

Assuming we have an approximately constant flow field for the top and bottom of our fin platform, in the vertical plane (x- and z-axis), and apply mass conservation laws, we know that the amount of fluid passing over the top of the structure is equivalent to the amount of fluid passing underneath. In potential flow theory, this applies to all angle–of–attacks, and you could calculate the lift force.

--- Page 6 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

Due to symmetry about the chord, when our hydrofoil is aligned in the direction of flow, the flow over the top will be equivalent to the flow underneath the hydrofoil. For in-air applications, a strong choice to measure flow speeds are anemometers. p. 2

Where the paper says it

Due to symmetry about the chord, when our hydrofoil is aligned in the direction of flow, the flow over the top will be equivalent to the flow underneath the hydrofoil. For in-air applications, a strong choice to measure flow speeds are anemometers.

Constant temperature anemometers contain two fixed resistors, R1 and R2, a temperature dependent resistor, Rw, and lastly a variable resistor, R3. p. 2
Where the paper says it

This was seen as ideal because resistors could be exchanged as needed. Constant temperature anemometers contain two fixed resistors, R1 and R2, a temperature dependent resistor, Rw, and lastly a variable resistor, R3, to bring the bridge back into balance.

As flow passes over the temperature dependent resistor the unbalancing of the resistor bridge results in a voltage difference, which is compensated through the current in the system. p. 2
Where the paper says it

Constant temperature anemometers contain two fixed resistors, R1 and R2, a temperature dependent resistor, Rw, and lastly a variable resistor, R3, to bring the bridge back into balance. As flow passes over the temperature dependent resistor the unbalancing of the resistor bridge results in a voltage difference, which is compensated through the current in the system [Perry and Morrison].

--- Page 7 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

In order to move the position of the hydrofoil, in accordance with the resultant anemometer readings, a servo motor was used. With the anemometers and a single servo motor, we can now describe code, in C/C++, to archive data as well as reorient our hydrofoil. p. 3

Where the paper says it

R1R3 = R2Rw (2) In order to move the position of the hydrofoil, in accordance with the resultant anemometer readings, a servo motor was used. With the anemometers and a single servo motor, we can now describe code, in C/C++, to archive data as well as reorient our hydrofoil.

--- Page 8 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The first iteration fin is capable of detecting unidirectional flows, operating in the x-y coordinate plane and is oriented orthogonally to such plane. The foil was additively manufactured with a cartesian based 3-D printer using PLA filament and mounted to a wooden board for stability, simulating a rigid body, i. p. 3

Where the paper says it

Additionally, the foil is hollowed out for decreased system mass; in water these considerations may be less of a concern due to Archimedes’ principle, and a parallel orientation with the ocean surface will be necessary to characterize the sea state above. The foil was additively manufactured with a cartesian based 3-D printer using PLA filament and mounted to a wooden board for stability, simulating a rigid body, i.

e. an AUV/ROV. p. 0
Where the paper says it

Additionally, hydrofoils are paralleled with species of Testudines. We have seen research journals mimicking sea turtle flipper motion that address the benefits of biomimicry; however, research has only gone as far as exploring thrust capabilities and mobility characteristics within AUV and ROV systems [Liu et al.

--- Page 9 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

Testing of the fin as a data acquisition system included a low-power fan (120VAC, 0.25A, 60Hz) capable of in-line flow at the source of approximately 3. p. 3

Where the paper says it

1 Experimental Setup Testing of the fin as a data acquisition system included a low-power fan (120VAC, 0. 25A, 60Hz) capable of in-line flow at the source of approximately 3.

5 m/s and controlled angles at which the flow would reach the leading edge. p. 3
Where the paper says it

25A, 60Hz) capable of in-line flow at the source of approximately 3. 5 m/s and controlled angles at which the flow would reach the leading edge.

The testing is designed to assess the ability of the foil to accurately relay position, over time, to the micro-controller for post-processing and future testing in an ocean environment. p. 3
Where the paper says it

The fan faces the leading edge of the foil and is moved to angular positions of 90°, 140°, 105°, 60°, 150°, 105°, 150°, and 130°over the course of approximately 50 seconds. The testing is designed to assess the ability of the foil to accurately relay position, over time, to the micro-controller for post-processing and future testing in an ocean environment.

--- Page 10 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. p. 4

Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

p. 4
Where the paper says it

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered [Fig. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used.

The sign of the percent differences indicate what side the flow was originating, i. p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

p. 4
Where the paper says it

We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.

e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow. p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

p. 4
Where the paper says it

The sign of the percent differences indicate what side the flow was originating, i. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 11 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

Without centering the heading of the foil with the direction of flow, there are no percent differences larger than 2.00% and no percent differences smaller than 0. p. 4

Where the paper says it

08% Without centering the heading of the foil with the direction of flow, there are no percent differences larger than 2. 00% and no percent differences smaller than 0.

40% (excluding the resting position). p. 4
Where the paper says it

00% and no percent differences smaller than 0. 40% (excluding the resting position).

Improvement to this data may take the form of decreasing the threshold that was used or swapping out the hardware for more precise components. p. 4
Where the paper says it

40% (excluding the resting position). Improvement to this data may take the form of decreasing the threshold that was used or swapping out the hardware for more precise components.

The variable sampling rate will help reduce the length of the outputted file, required processing, and ultimately increasing the total range and power in the system. p. 4
Where the paper says it

65 seconds; however, the interrupt is not generated and registered until another two samples are taken, increasing the variability between measurements [Fig. This variable sampling rate will help reduce the length of the outputted file, required processing, and ultimately increasing the total range and power in the system; however, more work must 5

The benefits of a system like the one proposed become more prevalent with its ease of operation and ability to process the collected data. p. 5
Where the paper says it

be done to increase efficiency. The benefits of a system like the one proposed become more prevalent with its ease of operation and ability to process the collected data.

--- Page 12 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 13 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 14 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 15 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 16 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 17 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 18 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 19 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

--- Page 20 ---

Design and Formulation of a Hydromechanical Fin for AUV Operations and Wave Parameter Estimation

The foil was able to quickly and consistently move to the new location and maintain its position until a new flow direction was encountered. We can see that the rise and fall time of the foil heading is approximately forty degrees per second with the servo motor used. The sign of the percent differences indicate what side the flow was originating, i.e. left or right, and we can further assess the hydrofoil’s ability to accurately orientate itself in the direction of flow.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AUV navigation through rheotaxis allows for orientation in flow direction using a single hydrofoil, which can quickly and accurately orientate itself in the direction of flow for better mission run positioning and tracking.

  2. The system can characterize ocean surface conditions at or near the upper ocean layer by utilizing the hydrofoil's positioning to estimate wave parameters such as wave height and current through Wave mechanics and a geometric proof were applied to estimate wave parameters such as wave height and current from the hydrofoil’s positioning.

  3. The AI system can process real-time data from anemometers with variable sampling rates, allowing it to adjust its detection sensitivity based on flow conditions, which helps characterize multi-frequency waves and increase efficiency.

Abstract

Ocean dynamics play a crucial role in global climate, ecosystems, and human activities, necessitating accurate and efficient methods to characterize ocean currents and waves. This paper presents the development of a novel bio-inspired hydrofoil system for detecting and characterizing ocean currents and waves based on a dolphin's flipper foil design. The prototype's performance was assessed through controlled experiments, demonstrating the system's ability to quickly and accurately orientate itself in the direction of flow. Wave mechanics and a geometric proof were applied to estimate wave parameters such as wave height and current from the hydrofoil's positioning. The proposed hydrofoil system shows potential for use in various marine applications, including oceanographic research, environmental monitoring, and navigation. The bio-inspired hydrofoil system offers a promising approach to ocean current and wave characterization, with the potential to significantly impact our understanding and monitoring of ocean dynamics without greatly impacting vehicle performance or increasing power utilization in operation.

Related papers