Anomalous Nernst Effects of [CoSiB/Pt] Multilayer Films

arXiv:1308.5485 · cond-mat.mtrl-sci, cond-mat.mes-hall · Submitted 2013-08-26 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Anomalous Nernst Effects of

CoSiB/Pt: Multilayer Films".

Mira: Here's the gist of the paper. Anomalous Nernst effects of

CoSiB/Pt: multilayer films are measured using local heating to reveal a characteristic hysteresis in the Nernst voltage that reflects film magnetization, suggesting a crossover in heat transport between 2D and 3D cases Experimental Setup and Sample Preparation The ferromagnetic multilayer film of

CoSiB/Pt: was deposited on an oxidized Si wafer using a DC magnetron sputtering method After depositing buffer layers with 50 Å of Ta and 30 Å of Pt, repeated layers of 6 Å-thick CoSiB and 14 Å-thick Pt were deposited The multilayer film was fabricated into a Hall bar-shaped device using photolithography and ion-milling A separate tungsten heater pattern was made across the longitudinal arm of the Hall bar at one end All measurements were performed at room temperature using a Keithley 2400 source meter and an electromagnet Detection of Anomalous Contributions In Fig.

Kai: 1 (c) and (d), the measurement shows a clear hysteresis of VN reflecting the anomalous contribution that results from the magnetization of the film, as in the case of VH The drive current flows along the Hall bar when VH is measured but there is no drive current when VN is measured Instead, a temperature gradient induced by the heater makes a thermal current flow and the electronic contributions of the thermal current along the Hall bar result in the developments of VN in the presence of B The magnitude of VN depends on the power generated by the heater as shown in Fig.

Mira: 2 (c), where a linear fit in a log-log scale has a slope about 1.15, confirming that the signal is from the thermal origin Spatial Dependence of Thermal Gradients The magnitude of VN is roughly proportional to 1.

Title and authors: Kai: The core of this paper is measuring anomalous Nernst effects using local heating to reveal a characteristic hysteresis in the Nernst voltage that reflects the film's magnetization, similar to what you see with anomalous Hall effects.

Mira: They are using a local heating geometry, and they found that the drive current flows along the Hall bar when they measure the voltage under one condition, but there is no drive current when they measure it under another condition.

Lev: So they set up a thermal current flow using the heater to induce a temperature gradient, and this thermal current causes an electronic contribution of the thermal current along the Hall bar that results in these anomalous Nernst voltages when there's a magnetic field present.

Kai: The magnitude of that voltage, the anomalous Nernst voltage, it depends on the power generated by the heater. They found that when you plot this relationship on a log-log scale, they get a linear fit with a slope of about one point fifteen which confirms that the signal is coming from the thermal origin.

Mira: What’s important here is how they are using this local heating setup to probe the thermal transport characteristics of the film, rather than just assuming a constant temperature gradient.

Lev: And that's where it gets interesting for real hardware; if you want to run this on a real device, you need to account for these local effects and how the thermal environment changes things.

Kai: They also measured the dependence of this anomalous Nernst voltage on the distance d from the heater, and they found that it is roughly proportional to one point three over d, which they conjectured from what's expected in terms of the heat equation <ref:1308.5485#pg1,anomalous Nernst voltage on the distance d from the>.

Mira: So, that spatial dependence tells us something about how heat moves through these multilayer films, specifically hinting at a crossover between the two-dimensional and three-dimensional cases.

The paper's summary: Kai: One big improvement they point out is that using local heating allows them to predict heat transport characteristics more accurately because it generates a non-constant temperature gradient, which isn't assumed in previous experiments where people just assume a constant temperature gradient, D over D T x over.

Mira: That’s a significant methodological step because it moves beyond the assumption of uniformity that limits older measurements. They are now getting local information about how heat actually flows through the material as you probe it.

Lev: From an engineering standpoint, knowing that the voltage depends on distance d from the heater is crucial for designing things like nanoscale thermal probes or sensors, because you need to know where that signal is coming from spatially.

Kai: And another way they suggest this helps is by using the measured anomalous Nernst voltage itself as a method for temperature measurement. It’s suggested that you can deduce the dependence of the temperature gradient on the distance from the heater just by measuring these voltages from different probing contacts since they are proportional to that gradient.

Mira: That shifts how we think about sensing; instead of needing a separate thermometer, you can use this intrinsic property of the film—the anomalous Nernst effect—to map out local temperature variations.

Lev: If you were building an error correction scheme for this material, knowing this spatial dependence helps determine the overhead because you know exactly how sensitive your measurement is to the thermal environment.

Kai: So, essentially they've moved from averaging a response over a macroscopically sized sample to mapping out local responses using these controlled thermal gradients.

The paper's improvements: Mira: To wrap up, the main implication of this paper on "Anomalous Nernst Effects of

CoSiB/Pt: Multilayer Films" is that the film structure exhibits a crossover in heat transport between 2D and three dee cases, which is revealed through the distance dependence of that anomalous Nernst voltage.

Lev: For hardware, this means we need to model thermal effects more precisely because you can't treat the temperature gradient as a simple constant; it changes with distance d from the heater, following that one point three over d relationship.

Kai: So, while they’ve shown how to probe these films locally and found a characteristic hysteresis tied to magnetization, the key is using that spatial dependence to understand the underlying physics of heat conduction in these specific multilayer structures.

Mira: And if you can use this voltage signal itself for temperature measurement, that opens up a new way to characterize thermal properties without needing external probes.

Lev: It’s a solid result because it connects the magnetic response, the thermal transport, and spatial dependence all in one measurable quantity.

Conclusion: Kai: So we’re wrapping up on "Anomalous Nernst Effects of

CoSiB/Pt: Multilayer Films." Basically, they used local heating to see how the film's magnetization affects the voltage and found a hysteresis that points to a crossover in heat transport.

Mira: Right, so they looked at how heat moves in these multilayer stacks and it’s not simple 2D or simple three dee anymore; it’s somewhere in between <ref:1308.5485#pg1>.

Lev: From an error correction standpoint, if you run this on real hardware, you can't just assume a constant temperature gradient anymore; the dependence on the distance d from the heater is what matters for your overhead calculations.

Kai: Exactly. They showed that this voltage signal actually tells you where you are in terms of thermal environment because it’s proportional to that distance d relationship, roughly one point three over d.

Mira: That spatial dependence is key; it means the material's heat flow isn't uniform across the whole sample, which is a big assumption we usually make in these kinds of studies.

Lev: If we are building sensors, knowing this scaling helps us decide if our measurement setup has enough resolution to capture that gradient change without noise.

Kai: And they even suggested you could use the measured voltage itself as a way to measure the temperature, instead of relying on traditional properties like the coercive field.

Mira: That’s interesting because it means we can get a local thermal map using just our electrical measurements on the film, which is much more direct than needing a separate thermometer.

Lev: For error correction, if you can sense that local temperature variation, you might be able to incorporate thermal fluctuations into your noise model directly instead of treating them as external disturbances.

Kai: So, to summarize the paper "Anomalous Nernst Effects of

CoSiB/Pt: Multilayer Films," they confirmed magnetization causes a voltage hysteresis and that this signals a crossover in heat transport between 2D and three dee regimes <ref:1308.5485#pg1,Anomalous Nernst Effects of CoSiB/Pt Multilayer Films>.

Mira: It’s a solid piece of experimental work showing how structure dictates the thermal dynamics, especially when you’re dealing with these complex multilayer systems.

Lev: It gives us better constraints for designing quantum devices where thermal noise might be more relevant than we thought when we were only looking at simple models.

Kai: Anyway, that's the latest from this paper; next time we’ll look at those circular phonons and what they mean for magnetization in insulators.

O. Kelekci, H. N. Lee, T. W. Kim, H. Noh

Department of Physics and Graphene Research Institute, Sejong University · Department of Advanced Materials Science and Engineering, Sejong University

cond-mat.mtrl-sci, cond-mat.mes-hall

Submitted: 2013-08-26

Updated: 2013-08-26

Comments: 4 figures

Journal ref: J. of Magnetics, Vol. 18, p. 225 (2013)

DOI: 10.4283/JMAG.2013.18.3.225

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 76/100

The gist: Anomalous Nernst effects of [CoSiB/Pt] multilayer films are measured using local heating to reveal a characteristic hysteresis in the Nernst voltage that reflects film magnetization…

Key concepts

Anomalous Nernst Effects
These are unusual voltage measurements observed in the film that depend on magnetic properties, specifically magnetization. By heating locally, researchers could isolate this effect from standard transport mechanisms.
Magnetization Hysteresis
The measured voltage showed a clear hysteresis loop when subjected to different magnetic conditions. This hysteresis is directly linked to how the film's magnetization state influences the anomalous Nernst response during thermal transport.
Heat Transport Crossover
The study suggests that heat moves through the film in two distinct ways: a 2D-like conduction and a 3D-like conduction. Analyzing how the anomalous voltage changes with distance (d) helps determine which regime dominates at different scales.

Terminology

Summary

Anomalous Nernst effects of [CoSiB/Pt] multilayer films are measured using local heating to reveal a characteristic hysteresis in the Nernst voltage that reflects film magnetization, suggesting a crossover in heat transport between 2D and 3D cases

Experimental Setup and Sample Preparation

The ferromagnetic multilayer film of [CoSiB/Pt] was deposited on an oxidized Si wafer using a DC magnetron sputtering method After depositing buffer layers with 50 Å of Ta and 30 Å of Pt, repeated layers of 6 Å-thick CoSiB and 14 Å-thick Pt were deposited The multilayer film was fabricated into a Hall bar-shaped device using photolithography and ion-milling A separate tungsten heater pattern was made across the longitudinal arm of the Hall bar at one end All measurements were performed at room temperature using a Keithley 2400 source meter and an electromagnet

Detection of Anomalous Contributions

In Fig. 1 (c) and (d), the measurement shows a clear hysteresis of VN reflecting the anomalous contribution that results from the magnetization of the film, as in the case of VH The drive current flows along the Hall bar when VH is measured but there is no drive current when VN is measured Instead, a temperature gradient induced by the heater makes a thermal current flow and the electronic contributions of the thermal current along the Hall bar result in the developments of VN in the presence of B The magnitude of VN depends on the power generated by the heater as shown in Fig. p. 4 2 (c), where a linear fit in a log-log scale has a slope about 1. p. 415, confirming that the signal is from the thermal origin

Spatial Dependence of Thermal Gradients

The magnitude of VN is roughly proportional to 1.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI systems can accurately predict heat transport characteristics by utilizing local heating to generate a non-constant temperature gradient, which is not assumed in previous experiments where the temperature gradient was assumed to be a constant of D D T x /.

  2. The improved system can deduce the nature of heat conduction as being in a crossover between the 2D and the 3D case by analyzing the distance dependence of anomalous Nernst voltage, which is shown to be roughly proportional to 1.3 1/ d.

  3. AI systems can potentially utilize the measured VN signal itself as a method for temperature measurement, in comparison with other temperature-dependent properties like the coercive field Hc, as suggested by the observation that the dependence of the temperature gradient on the distance from the heater can be obtained by measuring VN from different probing contacts since VN is proportional to the temperature gradient.

Related papers