Ultralow-Energy Measurements using the Startpoint of beta Decays
summary
The gist
Ultralow-Energy Measurements using the Startpoint of beta Decays proposes a novel measurement of β decays using low-temperature solid-state detector technologies to search for heavy sterile…
In short
This research proposes using the 'beta startpoint'—where beta kinetic energy is zero—to search for heavy sterile neutrinos in the keV–MeV range. This technique offers a unique probe of weak nuclear physics and allows for sensitivities that surpass current limits. Additionally, measuring the daughter nucleus recoil spectrum helps calibrate solid-state detectors used in sub-GeV dark matter searches.
Key concepts
- Beta Startpoint
- This is a specific point in the beta decay spectrum where the kinetic energy of the emitted beta particle is zero. At this moment, the emitted neutrino and recoiling daughter nucleus emerge back-to-back. This feature is sensitive to neutrino mass, allowing researchers to search for heavy sterile neutrinos.
- Nuclear Recoil Response Calibration
- The recoil spectrum of the daughter nucleus provides a way to calibrate how solid-state detectors respond to nuclear energy deposits. This is crucial because current dark matter searches often assume the response to nuclear and electron recoils is equivalent. Measuring this spectrum directly tests that assumption.
- Defect-Induced Quenching vs. Sterile Neutrino Emission
- The paper distinguishes between two potential effects shifting the startpoint energy: defect quenching, which causes a uniform shift across the entire spectrum, and sterile neutrino emission. Sterile neutrino emission creates a distinct secondary spectral feature whose position depends on the neutrino's mass and coupling strength.
Terminology used across episodes
This episode discusses
- Ultralow-Energy Measurements using the Startpoint of beta Decays · Paper Radio
- Low Energy Phonon Bursts Created By Fast Neutron Damage
- Development Status of the KIPM Detector Consortium
- Assessing the operating characteristics of an ion-milled phonon-mediated quantum parity detector
- A First Demonstration of the SQUAT Detector Architecture: Direct Measurement of Resonator-Free Charge-Sensitive Transmons
- The Superconducting Quasiparticle-Amplifying Transmon: A Qubit-Based Sensor for meV Scale Phonons and Single THz Photons
- Improved limit on the effective electron neutrino mass with the ECHo-1k experiment
- eV-scale Sterile Neutrinos
- Sterile Neutrinos
- Sterile Neutrino Dark Matter
- Direct neutrino-mass measurement based on 259 days of KATRIN data
- Searches for massive neutrinos with mechanical quantum sensors
- Limits on the Existence of sub-MeV Sterile Neutrinos from the Decay of 7 Be in Superconducting Quantum Sensors
- First observation of single photons in a CRESST detector and new dark matter exclusion limits
- Understanding radioactive ion beam production at ISAC through yield measurements and simulations
- Production of clean rare isotope beams at TRIUMF Ion guide laser ion source
- Nuclear Theory and Science of the Facility for Rare Isotope Beams
- Charge Breeding of Radioactive Ions
- Status of the JENSA gas-jet target for experiments with rare isotope beams
- Radiation Induced Point and Cluster-Related Defects with Strong Impact to Damage Properties of Silicon Detectors
- Reduction of Trapping and Recombination in Upgraded Metallurgical Grade Silicon: Impact of Phosphorous Diffusion Gettering
The paper
Ultralow-Energy Measurements using the Startpoint of beta Decays · Read on arXiv
Lawrence Berkeley National Laboratory
We propose a novel measurement of β decays using low-temperature solid-state detector technologies. The β startpoint, where the β kinetic energy is zero, offers a unique probe of weak nuclear physics that has not yet been exploited experimentally. We describe how this technique enables searches for heavy sterile neutrinos in the keV--MeV energy range and show that, with current technologies, sensitivities to sterile neutrino coupling to electrons can be achieved that exceed the current best constraints. The spectrum produced by the recoiling daughter ion also offers a calibration of the nuclear recoil response, critical for both sub-GeV dark matter searches and coherent elastic neutrino-nucleus scattering (CE ν NS) measurements. We outline a potential experimental scheme using neutron activation to produce 32 P in situ in a silicon substrate, discuss projected sensitivities to sterile neutrinos, and evaluate the prospects for nuclear recoil calibrations.
DOI: 10.1103/k67t-jlkq
Transcript
Introduction to the show: ident: High Energy Physics: Experiment. The day in high-energy experiment: detectors, searches and limits.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Ultralow-Energy Measurements using the Startpoint of beta Decays".
Mira: Here's the gist of the paper. Ultralow-Energy Measurements using the Startpoint of beta Decays proposes a novel measurement of β decays using low-temperature solid-state detector technologies to search for heavy sterile neutrinos and calibrate nuclear recoil responses The β startpoint, where the β kinetic energy is zero, offers a unique probe of weak nuclear physics that has not yet been exploited experimentally Pruning redundant reasoning tokens The paper describes how this technique enables searches for heavy sterile neutrinos in the keV–MeV energy range and shows that, with current technologies, sensitivities to sterile neutrino coupling to electrons can be achieved that exceed the current best constraints The distinct spectral shape of the β startpoint is sensitive to the emission of massive neutrinos This search complements other ongoing and proposed searches, including measurements of the β endpoint of 3H decays
21: , kinematic reconstruction of β decays
22: , and measurements of electron capture decays
13, 15, 16: How the training signal is built The Q-value of a β decay defines the kinetic energy, T, available to the progeny isotopes and the nonzero neutrino mass, mν The startpoint of the β spectrum is defined as Tβ → 0 where pν = pd At this point in the spectrum, the emitted β is at rest, such that the emitted neutrino and recoiling daughter nucleus emerge back-to-back The kinetic energy of the recoiling daughter ion, Td at the β startpoint is Td = Q − Eν = Q + md − q/m2d + m2ν + 2mdQ For example, 3H β decays (Q = 18.59 keV) have recoiling ion energy of Td = 61.5 meV at the β startpoint The amount by which the recoiling ion energy changes as a function of neutrino mass can be calculated by expanding Eq.
Kai: 3 in powers of mν Neutrino masses on the meV-scale would produce vanishingly small shifts to the β startpoint energy However, massive neutrinos on the order of 10 keV or greater would lead to ∆Td values measurable by current or near-future experiments Where the gains come from The recoil spectrum of the daughter nucleus provides an opportunity to calibrate the nuclear recoil response of solid-state detectors — an essential task for sub-GeV dark matter searches utilizing athermal phonon sensors The observation of the β startpoint feature enables a direct probe of the nuclear recoil response in athermal phonon detectors This allows us to address two important questions: (1) what is the scale of defect-induced quenching for low-energy nuclear recoils, and (2) is there variation in the detector energy resolution between nuclear and electronic recoils Systematic Uncertainties The systematic uncertainty on the startpoint energy arising from the Q-value uncertainty is small with respect to the β startpoint energy An important procedural step will be to independently calibrate the 32P activity within the silicon substrate If defect-induced quenching of nuclear recoils is present, the observed startpoint energy could be shifted to a value below the predicted 49.1 eV by a constant offset related to the energy lost to lattice defect creation This shift would be degenerate with the effect of a sterile neutrino, which also shifts the startpoint to lower energies Alternative Isotopes and Substrates The first is 90Y, which can be produced via thermal neutron capture on 89Y in an analogous fashion to the 31P(n, γ) process described in Sec.
Mira: III With a Q-value of 2278.5 keV, the 90Y β startpoint produces a 90Zr daughter recoil at 31.0 eV — within the demonstrated energy resolution of current detectors The second isotope of interest is 76As, a high-Q (Q = 2960.6 keV) β emitter that produces a 76Se daughter recoil of 62.0 eV at the β startpoint — comfortably above current detector thresholds and comparable to the 32P recoil energy Outlook The measurement proposed here opens a new window on weak nuclear physics at ultralow energies The β startpoint provides simultaneous sensitivity to sterile neutrinos and the nuclear recoil response in solid-state detectors, two of the most pressing questions in particle physics and sub-GeV dark matter detection Initial R&D will focus on demonstrating neutron activation of phosphorus-doped silicon wafers, characterizing the resulting backgrounds, and performing the first measurement of the β startpoint spectrum The technique will serve as both a discovery tool for sterile neutrinos and an essential calibration method for the next generation of sub-GeV dark matter searches Supplemental Materials The Q-value of a β decay is defined as the mass difference between the parent isotope mp and the daughter isotope md with the additional subtraction of the electron mass me The predicted observed spectrum for 32P in such a detector, considering a 1 eV detector resolution, is shown in Fig.
Kai: 2 The emission of these heavy neutrinos shifts the β startpoint to lower energies by 4.2 eV, 16.8 eV, and 37.8 eV, respectively The sensitivity improves as the sterile neutrino mass increases due to the sterile neutrino spectrum shifting further from the β startpoint and the increased fraction of decays in this low-energy regime In both cases, the SM 32P decays are considered The LEE background is the dominant background with the largest systematic uncertainty at low energies If defect-induced quenching of nuclear recoils is present, the observed startpoint energy could be shifted to a value below the predicted 49.1 eV by a constant offset related to the energy lost to lattice defect creation The two effects could be distinguished by their spectral signatures: quenching produces a uniform energy scale shift that affects the entire spectrum, whereas sterile neutrino emission produces a distinct secondary spectral feature whose shape and position depend on the neutrino mass and coupling strength If defect-induced quenching is observed at the predicted startpoint energy, it would imply that current sub-GeV dark matter limits from athermal phonon detectors, which assume equivalent response to nuclear and electronic recoils, are weaker than reported The presence of dual-channel readout could provide significant additional discriminating power in this measurement Acknowledgments The authors thank Peter Sorensen for insights on this work DK thanks Giacomo Marocco for useful discussions This work was supported by the U.S.
Title and authors: Kai: So we're looking at this paper now, "Ultralow-Energy Measurements using the Startpoint of beta Decays." It sounds like a deep dive into some very specific physics using low-temperature detectors. It’s about how you can use the startpoint of beta decays to look for things that haven't been seen before.
Mira: Exactly. The title points straight to the core idea: using this zero kinetic energy point in a beta decay spectrum as a unique probe of weak nuclear physics. It suggests they are looking for heavy sterile neutrinos, and also using this measurement to calibrate how these solid-state detectors respond to nuclear recoils, which is super important for dark matter searches.
Lev: From an error correction standpoint, if you're targeting the startpoint, you're dealing with extremely low energy depositions, right? That puts you right in the realm where noise and background systematics really start to dominate the signal.
Kai: Right. So what they propose is using this point to search for heavy sterile neutrinos in the keV to MeV range, which is a pretty interesting energy window for this kind of physics.
Mira: And they claim that with current technologies, the sensitivity to sterile neutrino coupling to electrons can actually exceed what we currently think is possible from other methods. That's a big claim because it pushes the limits of what we know about these couplings.
Lev: But achieving that sensitivity relies heavily on how well you model the background at those ultralow energies, which brings us right to their calibration idea.
The paper's summary: Kai: Okay, so the paper lays out how they define this startpoint. They say it’s where the beta kinetic energy is zero, and at this point, the emitted neutrino and the recoiling daughter nucleus are essentially back-to-back in momentum.
Mira: That geometric constraint is key because it simplifies how we calculate the kinetic energy of that recoiling daughter ion, which they call Td. They give us a formula for Td at this startpoint: Td equals Q plus m nu squared minus q over m squared d plus two m d Q.
Lev: That formula immediately tells you that the dependence on the Q value and the mass of that daughter nucleus is what constrains which isotopes are even feasible to measure experimentally. They use a couple of examples to show this, like three hydrogen beta decays having a recoiling ion energy of sixty-one point five milli-electron volts at this startpoint.
Kai: Sixty-one milli-electron volts sounds incredibly small, which is why they say it's not currently measurable with existing technology. But then they pivot to isotopes like thirty two phosphorus and ninety yttrium, which have much higher Q values and produce recoiling ion energies of thirty one point zero electron volts or sixty two point zero electron volts respectively.
Mira: So the point is, while the hydrogen decay at the startpoint is tiny, decays from heavier isotopes give you measurable recoil energies that are comparable to what current detectors can handle.
Lev: That shift in Q value across different isotopes gives us a way to map out where this measurement will actually be feasible on real hardware.
Kai: And they also mention how neutrino masses affect this point; if the neutrino mass is small, like in the milli-electron volt range, it barely shifts Td. But if there are massive neutrinos on the order of ten keV or greater, that causes shifts in Td that current experiments can actually measure.
The paper's improvements: Mira: Moving past just measuring things, they suggest a few ways to make this technique even more useful and robust. One big improvement is using the recoil spectrum of the daughter nucleus as a way to calibrate the nuclear recoil response in solid-state detectors.
Kai: That calibration part is what really interests me from a hardware side. It addresses that big assumption we often make in sub-GeV dark matter searches, which is that the detector response to electron recoils and nuclear recoils is equivalent. They want to know if there's actually variation in detector energy resolution between nuclear and electronic recoils at these low energies.
Lev: From a real hardware perspective, that dual-channel readout idea you mentioned would be powerful for this calibration. Having interleaved sensitive ionization and phonon detectors could give us the first direct constraint on the ionization yield in this regime, which is crucial.
Mira: And they also tackle the systematic uncertainties head-on. They note that while the uncertainty from the Q value itself is small compared to Td, there's a potential issue with defect-induced quenching of nuclear recoils.
Kai: Ah, defect quenching. They suggest this could shift the observed startpoint energy down to a value below forty nine point one electron volts by an offset related to energy lost to lattice defects.
Lev: If that quenching effect is real, it gets tricky because it shifts the startpoint energy uniformly across the entire spectrum, whereas sterile neutrino emission produces a different spectral feature whose shape depends on the neutrino mass and coupling strength.
Mira: So you can potentially distinguish between those two effects by looking at their spectral signatures. That's a really important distinction for interpreting any future data from this measurement.
Conclusion: Kai: So to wrap up, this paper proposes using the startpoint of beta decays as a way to simultaneously probe heavy sterile neutrinos and calibrate the nuclear recoil response in solid-state detectors. It opens up a new window into weak nuclear physics at very low energies.
Mira: And they're aiming for that simultaneous sensitivity, which addresses two major questions: what is the scale of defect-induced quenching for those low-energy nuclear recoils, and is there variation in detector energy resolution between nuclear and electronic recoils.
Lev: On the hardware side, their suggestion to use dual-channel readout systems to measure both signals simultaneously offers a way to get that first direct constraint on ionization yield in this regime.
Kai: It seems like the path forward involves demonstrating neutron activation of phosphorus doped silicon wafers, characterizing those backgrounds, and performing that first measurement of the startpoint spectrum.
Mira: And if they find evidence for defect quenching at forty nine point one electron volts, it would mean that current sub-GeV dark matter limits from athermal phonon detectors are weaker than previously reported because they assume an equivalent response to nuclear and electronic recoils.
Lev: We're seeing this as a path toward using this technique not just for discovery, but as an essential calibration method for the next generation of sub-GeV dark matter searches.
Kai: This paper, "Ultralow-Energy Measurements using the Startpoint of beta Decays," gives us a way to look at weak nuclear physics at ultralow energies by exploiting this specific spectral feature.
Mira: It’s a fascinating piece of work because it connects particle physics searches with the practical calibration needs of our detectors.
Lev: And we'll be keeping an eye on how they move from theory to building that kind of experiment.
More episodes
- Daily Summary for 2026-11-19
- 2512.21290-Model-independent ZH production cross section at FCC-ee
- 2610.21982-First Observation of the Radiative Decay D 0 to gamma omega
- The day in conversation for 2026-11-19
- Daily Summary for 2026-11-19
- Daily Summary for 2026-11-18
- 2512.08065-Searches for Light Dark Matter and Evidence of Coherent Elastic Neutrino-Nucleus Scattering of Solar Neutrinos with the LUX-ZEPLIN (LZ) Experiment
- Daily Summary for 2026-11-18
- 2508.18022-Precision Measurements of the Electroweak Mixing Angle in the Region of the Z pole at the Large Hadron Collider
- 2512.23992-Prospect for measurement of CP-violating parameters of B s 0 to phi gamma at the Tera Z factory