Commissioning and Performance of the LHCb Upstream Tracker
summary
The gist
The Upstream Tracker is a new, high-precision silicon strip detector installed in the LHCb experiment as part of the overall LHCb Upgrade I project This detector plays a crucial role in the…
In short
The Upstream Tracker is a new silicon strip detector in LHCb that helps reconstruct charged particles for a software-based trigger. The system uses four planes of detectors with specific orientations to optimize resolution. The integration of the UT significantly improves momentum resolution and signal yields compared to previous runs, enabling higher luminosity and better physics results.
Key concepts
- Upstream Tracker (UT)
- A new high-precision silicon strip detector in LHCb consisting of four planes oriented at specific angles. Its purpose is to reconstruct charged particles, particularly long and downstream tracks, which are crucial for the fully software-based trigger system.
- SALT ASIC
- The 128-channel ASICs used to read out the UT sensors. This technology uses a differential low-power Successive Approximation Register (SAR) ADC that digitizes signals at 40 MHz. It includes digital processing for noise reduction and calibration.
- Downstream Tracks
- Tracks reconstructed by extrapolating segments from seven SciFi seeds to the UT detector. These tracks are essential for momentum measurement, and incorporating UT hits into them improves overall momentum resolution by about 10%.
Terminology used across episodes
This episode discusses
- Commissioning and Performance of the LHCb Upstream Tracker · Paper Radio
- The LHCb upgrade I
- LHCb Detector Performance
- A Downstream and vertexing algorithm for Long Lived Particles (LLP) selection at the first High-level trigger (HLT1) of LHCb
- HybridSeeding: A standalone track reconstruction algorithm for scintillating fibre tracker at LHCb
- The Joint COntrols Project Framework
- sPlot: a statistical tool to unfold data distributions
The paper
Commissioning and Performance of the LHCb Upstream Tracker · Read on arXiv
D. Andreou, M. Artuso, J. Bartz, B. Batsukh, A. Beiter, H. Bernstein, *S. Blusk*, *S. Ding*, *S. Ely*, J. Freiler, D. Germann, S Guerin, B Khanji, W Krupa i, A Kuhlman i, Z Li i, X Liang i, B Mack i, L M Mackey i, P Manning †E Minucci c R Mountain H Pham I Polyakov f M Polyakov M S Rudolph R S Sharma J Shupperd T Skwarnicki S Stone †A Venkateswaran e M K Wilkinson g H Wu J Andrew 2S Braun 2A D Fernez 2M Franco Sevilla 2C Hadjivasiliou P M Hamilton A Jawahery E Jiang L Meyer Garcia T O’Bannon W Parker Y Sun J Wimberly Z Yang A Alessandro A Capsoni A Carbone S Cesare i M Citterio S Coelli N Conti F DeBenedetti i P Gandini C Mancuso D Marangotto A Merli e M Monti N Neri M Petruzzo E Spadaro Norella a G Tonani D Vigano Z Wang F Zangari I Carli 4M Feng 4,14 Y Fu 4,q P Gorbounov 4 N.A. Grieser p X Jiang 4,14 Y Li 4 Y Li k S Liu i S Liu k Y Lu k S Sheng 14 e M Tobin J Wang X Yuan Y Yuan 14 Q Zou 14 M Firlej5 T Fiutowski5 M Hubczak5 M Idzik5 J Moron K.M. Sowa K Swientek T Szumlak C Abellan Beteta V Bell´ee I Bezshyiko V Denysenko G Hijano Mendizabal M Peco Regales N Serra O Steinkamp L Villardita C A Aidala K R Mattioli M Ram´ırez Garc´ıa J D Roth †D.M. Shangase M Brodski J C Lopes B Schmidt M Sokoloff Z Ren l D Y Tou G Vouters Q Han j G Wang 12 J Wu 12 X Zhu 12 T Li 13 X Wang T Chen P Li F Lazzari A Sergi F Zhang M van Veghel A Oyanguren J Zhuo Gao V Svintozelskyi 8,19 M De Cian 20 L Dufour 21 V Kholoimov 21 P Hoffmann 22 V.V. Gligorov, orgs_list_extracted_from_affiliations
European Organization for Nuclear Research (CERN) · University of Syracuse · University of Maryland · INFN Sezione di Milano · Institute Of High Energy Physics (IHEP) · AGH - University of Krakow · Physik-Institut, Universität Zürich · Lanzhou University · Université Savoie Mont Blanc, CNRS, IN2P3-LAPP · University of Michigan · INFN Sezione di Padova · Institute Of Particle Physics, Central China Normal University · State Key Laboratory of Nuclear Physics and Technology, South China Normal University · Physik-Institut, Universität Zürich · University of Cincinnati · European Organization for Nuclear Research (CERN) · INFN Sezione di Pisa · INFN Sezione di Genova · Institute Of High Energy Physics (IHEP) · AGH - University of Krakow · Physik-Institut, Universität Zürich · University of Michigan · INFN Sezione di Padova · Institute Of Particle Physics, Central China Normal University · State Key Laboratory of Nuclear Physics and Technology, South China Normal University
The Upstream Tracker is a new, high-precision silicon strip detector installed in the LHCb experiment as part of the overall LHCb Upgrade I project. The detector is an integral part of the tracking system, and plays a crucial role in the reconstruction of charged particles in the new fully software-based trigger. An overview of the Upstream Tracker detector design, its commissioning, and performance are presented.
Transcript
Introduction to the show: ident: High Energy Physics: Experiment. The day in high-energy experiment: detectors, searches and limits.
Kai: I'm Kai.
Mira: And I'm Mira, here with Lev.
Kai: We're looking at the paper: "Commissioning and Performance of the LHCb Upstream Tracker".
Mira: Here's the gist of the paper. The Upstream Tracker is a new, high-precision silicon strip detector installed in the LHCb experiment as part of the overall LHCb Upgrade I project This detector plays a crucial role in the reconstruction of charged particles in the new fully software-based trigger Detector Overview The UT detector consists of four planes of silicon-strip detectors The strips in the four planes are oriented at 0◦ (UTaX), −5◦ (UTaU), +5◦ (UTbV) and 0◦ (UTbX), respectively, in order to optimize the position resolution in the bending (xz) plane of the magnet, while providing sufficient precision in the y direction The four planes are built from vertically-mounted double-sided staves The UT detector is enclosed in a light-tight insulating box, that also serves as a Faraday cage Front-End Electronics and Calibration The UT sensors are read out by 128-channel ASICs implemented in 130 nm CMOS technology (SALT) The SALT ASIC uses a differential low-power 6-bit Successive Approximation Register (SAR) ADC digitizes signals at 40 MHz The digital back-end of the SALT ASIC includes a digital signal processing (DSP) for pedestal subtraction, common-mode subtraction (CMS), and zero suppression Calibration procedures are performed to optimize the configurable parameters in the SALT ASICs and the calibration procedures to monitor the optimal working point and the electronic noise Track Reconstruction The LHCb tracking system reconstructs several classes of tracks according to the subdetectors contributing to the reconstruction, as illustrated in Fig.
Kai: 6 The three principal track types containing UT hits are long, downstream, and upstream tracks Long tracks traverse the full tracking system, and generally have hits in the VELO, UT and SciFi detectors Downstream tracks are reconstructed from 7 SciFi seeds by extrapolating track segments to the UT The momentum resolution achieved after the HLT2 reconstruction of downstream tracks is comparable to that achieved in Run 2 (approximately 1%) Performance Evaluation The UT efficiency versus pT and pseudorapidity (η) shows an ∼ 2% decrease near η = 2.8, which is due to a set of locally inefficient regions in the UT The inclusion of the UT in the HLT1 pattern recognition proved essential for LHCb to reach its design luminosity 2.0 × 10 33 cm−2 s−1 The UT has also enabled LHCb to fully exploit the fully software-based trigger with respect to downstream tracking, resulting in signal yields (per fb−1) of decays with K0S and Λ baryons in the final state that are about 3 times larger than those obtained in Run 2 Monitoring and Stability The Low Voltage (LV) system supplies regulated low-voltage power to the hybrids (1.2 V) and the DCBs (1.5 V and 2.5 V), serving a total of 1,408 channels via 268 identical 8-channel low voltage regulator boards The UT detector safety system (DSS) runs autonomously and is built around industrial PLCs connected to numerous independent sensors Single-event upset (SEU) events in either the baseline DAC or pedestal registers are expected to occur at a rate of about 3.
Title and authors: Kai: So, we're looking at this paper now, "Commissioning and Performance of the LHCb Upstream Tracker," and it’s about getting this new silicon strip detector up and running. It seems like they are detailing the whole process from building it to actually making sure it works right in the detector.
Mira: Right, so what they're focusing on here is really on how they commissioned this Upstream Tracker, especially how those four planes of silicon strips—UTaX, UTaU, UTbV and UTbX—are performing after being installed.
Lev: From my side I’m interested in the front end electronics because that’s where the real noise and stability issues usually pop up when you move to a new system like this.
Kai: Exactly. They spend a good bit of time on that front end, specifically talking about these one hundred twenty-eight-channel ASICs they built, which use one hundred thirty nm CMOS technology. They detail how the Successive Approximation Register ADC digitizes signals at forty MHz and what kind of digital processing they have there for things like pedestal subtraction and zero suppression.
Mira: And it seems like a big part of their work is dealing with the temperature dependence of those calibration parameters, which is something that always has to be monitored in these kinds of detectors.
Lev: Because if you don't handle the temperature dependence right, the optimal working point shifts, and that throws everything off. They mention that they re-evaluated things like baseline DAC settings and zero suppression thresholds because those values change with temperature according to section four point two.three of this paper <ref:2611.08150#pg1>.
Kai: That makes sense from a hardware standpoint; you can't just assume the settings are static when the environment changes, so having an AI system optimize those SALT ASIC parameters dynamically based on temperature sounds like a smart next step they are pushing for in their improvements.
Mira: I think that dynamic optimization is where things get interesting because it moves beyond just fixing a static configuration; it’s about making the electronics adapt in real time to the operational environment.
Lev: It would take significant effort to build that kind of feedback loop into the DAQ system, but if they can nail those temperature corrections, it really helps stabilize the measurement before we even look at track reconstruction.
Kai: And beyond just tuning the electronics, they are also focused on how these hits actually translate into physics information through track reconstruction. They talk about three main track types: long tracks that go all the way through, downstream tracks reconstructed from seeds by extrapolating segments to the UT, and upstream tracks.
Title and authors: Mira: The paper seems very concerned with how the UT contributes to these different classes of tracks, especially downstream ones, because that's where they are getting their best performance metrics.
Lev: Specifically regarding downstream tracking, they say that after the High Level Trigger reconstruction using HLT2, the momentum resolution achieved is comparable to what we saw in Run two at approximately one percent <ref:2611.08150#pg3>. That’s a solid number for a system this complex.
Kai: And the paper points out that including this UT detector in the High Level Trigger pattern recognition was essential for LHCb to hit its design luminosity of two point zero times ten to the power of thirty three centimeters minus squared per second.
Mira: That luminosity target is huge, and it sounds like the Upstream Tracker was a necessary piece for reaching that goal, especially since it also lets them fully exploit the software-based trigger with respect to downstream tracking.
Lev: And they quantify that benefit by saying signal yields for decays with K zero S and lambda baryons in the final state are about three times larger than what they got in Run two <ref:2611.08150#pg3>. That’s a pretty substantial improvement in physics reach.
Kai: So, looking at the suggested improvements, one big thing is to get better at track reconstruction by using the UT hit information for both long and downstream tracks to reduce ghost tracks. They suggest that having two or more UT hits on a long track gives you a strong discriminant against those ghost tracks because they can't be there naturally.
Mira: That sounds like a good way to clean up the data before you even start looking for physics signals, reducing background noise right at the source of tracking information.
Lev: And another improvement is focusing on that downstream tracking efficiency itself, because they suggest that adding UT hits improves the overall momentum resolution by about ten percent relative to tracks formed without those UT hits. That’s a tangible gain we can count on if the reconstruction works as described.
Kai: I agree, a ten percent improvement in resolution is significant when you're pushing for precision measurements. But what about getting the physical detector geometry itself right? The paper suggests an automated geometrical alignment system using reconstructed long tracks to minimize residuals from the start.
Mira: That speaks to minimizing systematic errors related to how the detector was physically mounted or positioned relative to each other, which is always a big headache in these large experiments.
Title and authors: Lev: If you can use those long tracks as reference points for alignment and minimize that global chi squared of all tracks with respect to the alignment degrees of freedom, it cleans up the systematic errors significantly across the board.
Kai: Then there's this part about monitoring the electronics during calibration runs. They propose an online monitoring system that looks at zero suppression data while they are calibrating to give immediate feedback on average baseline and noise values down to individual ASICs or channels.
Mira: That’s proactive rather than reactive; you catch a problem before it ruins the whole calibration run, which is a huge operational win for any large detector setup.
Lev: And then there's the single event upset mitigation routine they suggest, where the system reads back register values every thirty seconds and reconfigures the affected ASIC block if it sees a discrepancy. It sounds like they are building in resilience against those inevitable radiation events.
Kai: So, to wrap up on this paper, "Commissioning and Performance of the LHCb Upstream Tracker," it’s about proving that this new detector setup is working as expected under real conditions, showing improvements in signal yields by a factor of three and boosting momentum resolution by about ten percent compared to tracks without UT hits.
Mira: Essentially, they are validating that this complex detector infrastructure can deliver the precision needed to exploit the fully software-based trigger effectively for searching for K zero S and lambda baryons.
Lev: And what this means is that when we consider putting this kind of tracking capability on real hardware, the overhead lands in managing those complex feedback loops and ensuring that dynamic temperature corrections actually keep those ASICs operating at their optimal point.
Kai: So, to summarize the implications for us here, the Upstream Tracker shows how crucial it is to integrate these new silicon systems—the hardware, the electronics tuning based on environment—and the reconstruction algorithms together to achieve those high-luminosity physics goals.
Mira: It really emphasizes that performance isn't just about having a fast detector; it’s about managing the entire system stack, from those one hundred thirty nm CMOS ASICs up through the pattern recognition software.
Lev: And for real hardware, it means we can expect these tracking systems to deliver better resolution and cleaner data if we invest in making those automated calibration and monitoring routines robust enough to handle the environment.
Kai: That’s where we'll be focusing next; how do these performance gains translate when you start talking about scaling this up or moving toward the next generation of detector upgrades.
The paper's summary: Kai: So, we're looking at how they got this new Upstream Tracker detector running after they installed it in LHCb.
Mira: They've essentially proven that this whole four-plane silicon strip setup works and is giving them the precision they need for particle tracking.
Lev: It seems like the focus there was really on getting the front end electronics stable, especially with those one hundred thirty nanometer chips.
Kai: Right, and they spent a lot of time dialing in those digital parts—the successive approximation register ADCs—to make sure the signals were digitized properly at that forty megahertz speed.
Mira: And they made it clear that because the environment changes, you have to treat things like the baseline settings and zero suppression thresholds as something that needs continuous adjustment based on temperature.
Lev: That’s where the real hardware challenge is; if you don't track those temperature shifts, your optimal working point shifts too, which messes up everything.
Kai: So they are pushing for an AI system that can dynamically adjust those Successive Approximation Register parameters based on the temperature and environmental conditions right when it happens.
Mira: That moves beyond a static calibration setup; it’s about making the electronics adapt in real time to keep the measurement accurate.
Lev: From a hardware standpoint, I think that dynamic optimization is tough to implement reliably, but if they can nail those feedback loops, it really stabilizes the detector before you even look at the track data.
Kai: And beyond just getting the electronics right for tracking, they focused heavily on how these hits actually help reconstruct different types of tracks.
Mira: They broke down the three main track types—the long ones that go through everything, and then those downstream tracks that are reconstructed by extrapolating segments from seeds.
Lev: The key result here is that the momentum resolution for those downstream tracks after high level trigger reconstruction is about one percent, which is comparable to what they achieved in run two.
Kai: That one percent resolution on the momentum scale is solid, and it’s a big deal because it shows the detector isn't just collecting hits; it's actually giving them usable physics data.
Mira: And they linked this performance directly to reaching their design luminosity of two point zero times ten to the power of thirty three centimeters minus squared per second.
Lev: So, without this Upstream Tracker, hitting that luminosity target would have been way out of reach with the existing system.
Kai: It also mentioned that because they included this tracker in the high level trigger pattern recognition, they could exploit the fully software based trigger much better for downstream tracking than before.
Mira: This means they are getting significantly higher signal yields for decays involving K zero S and lambda baryons, about three times larger than what was seen in run two.
Lev: That threefold increase in yield is a pretty substantial gain for the physics community to see when you’re looking at final state particles like that.
Kai: The paper also pointed out a specific issue where efficiency dropped by about two percent near pseudorapidity equal to two point eight, which was due to some locally inefficient regions in the detector itself.
Mira: So they aren't perfect across the board; there are these spots where the detector just isn't as good at reading hits.
Lev: That inefficiency is something you have to account for when you design your error propagation, and it’s a limitation you have to manage in your simulations.
Kai: They also laid out some concrete improvements they plan to make—things like using UT hits on both long and downstream tracks to reduce ghost tracks.
Mira: That’s a way of cleaning up the input data before the physics analysis even starts, which is always a smart move in complex tracking experiments.
Lev: And another improvement mentioned is an automated geometrical alignment system using those long tracks to minimize residuals, which cuts down on systematic errors from the detector's physical placement.
Kai: So, this paper shows how they’ve validated the hardware and then started planning how to use that validated data to push the physics results further.
Mira: It really boils down to successfully integrating a new piece of complex hardware with sophisticated software algorithms that are constantly being tuned for environmental changes.
The paper's improvements: Kai: So we've seen how they got the Upstream Tracker running, and now they are proposing specific ways to make it even better, right?
Mira: They’re focused on using that hit information we talked about earlier to clean up the reconstruction algorithms for both long and downstream tracks.
Lev: That sounds like a way to reduce those ghost tracks we mentioned; if you have two or more hits from the Upstream Tracker on a long track, it gives you a strong signal that it's real.
Kai: Exactly, so we’re taking the hardware data and using it as a discriminant against background noise right in the reconstruction step.
Mira: Then there’s this idea about improving downstream tracking efficiency by incorporating those Upstream hits; they suggest that adding those hits improves momentum resolution by about ten percent relative to tracks reconstructed without them.
Lev: A ten percent improvement in resolution is quite a lot, and it shows how much the Upstream Tracker helps when you're trying to get precision on these heavy particle decays.
Kai: And beyond the reconstruction algorithms, they’re looking at making the hardware itself smarter with an AI system that can adjust those Successive Approximation Register parameters based on temperature and environmental conditions.
Mira: That’s about making the electronics adaptive; it means you don't have to manually re-tune everything every time the detector gets a little warmer or cooler in the experiment.
Lev: I see that as a necessary step for real hardware; if you don't let the system self-adjust, you just end up with unstable measurements that kill your resolution gains.
Kai: They also suggested an automated geometrical alignment system using reconstructed long tracks to minimize residuals; this helps fix the physical placement errors of the modules.
Mira: It’s about using those long tracks as reference points to calculate a global chi squared of all the tracks, which smooths out those systematic errors from how things were physically mounted.
Lev: If you can automate that alignment based on track reconstruction, it takes a huge manual headache off the table and gets you closer to true precision.
Kai: Then there’s this online monitoring system for calibration runs; they want immediate feedback on average baseline and noise values down to individual ASICs or channels during those calibration procedures.
Mira: It’s proactive monitoring; you catch a problem as it happens during the measurement, instead of waiting for a big failure after the whole run is done.
Lev: That kind of real time feedback is crucial for stability, and it shows they are thinking about the operational side as much as just the physics results.
Kai: And finally, they suggested a single event upset mitigation routine; this involves reading back register values every thirty seconds and reconfiguring the affected ASIC block if there’s any discrepancy.
Mira: That’s building in resilience against those radiation events that we know happen in these high-energy environments; it’s about keeping the system running even when things get hit by a stray particle.
Lev: That level of automated hardware reconfiguration would be a huge weight on the processing, but it addresses one of the biggest risks for long-term detector operation.
Kai: So they’re moving from just proving that it works to designing an entire ecosystem where the detector and its electronics are continuously self-optimizing and self-correcting.
Conclusion: Kai: So we’ve covered how they built and tuned this new silicon detector in LHCb, and now we’re wrapping up this paper on the "Commissioning and Performance of the LHCb Upstream Tracker."
Mira: They essentially confirmed that this complex system is operational and delivering on its performance targets for particle tracking.
Lev: It seems like the main thing they achieved was validating that these front-end electronics work reliably under real operating conditions.
Kai: Right, and they showed how incorporating this detector into the high level trigger improved signal yields by a factor of three for decays involving K zero S and lambda baryons.
Mira: That threefold increase in yield is significant because it means we can now get much better statistics on those specific physics processes at LHCb.
Lev: From an error correction standpoint, that kind of yield boost is what you need to justify the complexity of running this detector on real hardware.
Kai: And they laid out a clear path forward with things like automated geometrical alignment and dynamic AI parameter optimization for the electronics.
Mira: It’s clear they are not just looking at a static setup; they’re designing a whole system that can adapt to environmental shifts while maintaining high precision.
Lev: If you look at the improvements, it really highlights that when you build real hardware, managing those feedback loops and keeping the temperature corrections stable is where the real engineering work lands.
Kai: So for anyone listening who just cares about what this means for physics, it’s that we have a more reliable tool now to measure particle momenta with high precision in these heavy collision experiments.
Mira: It validates the assumptions they made about how the detector will behave when pushed to the design luminosity of two point zero times ten to the power of thirty three centimeters minus squared per second.
Lev: The implication is that if you want precision on these kinds of final state particles, you need this kind of robust tracking infrastructure to be running reliably.
Kai: We’re going to keep digging into how they planned those single event upset mitigations and what the long term stability looks like for this whole setup.
More episodes
- Daily Summary for 2026-11-19
- 2512.21290-Model-independent ZH production cross section at FCC-ee
- 2610.21982-First Observation of the Radiative Decay D 0 to gamma omega
- The day in conversation for 2026-11-19
- Daily Summary for 2026-11-19
- Daily Summary for 2026-11-18
- 2512.08065-Searches for Light Dark Matter and Evidence of Coherent Elastic Neutrino-Nucleus Scattering of Solar Neutrinos with the LUX-ZEPLIN (LZ) Experiment
- Daily Summary for 2026-11-18
- 2508.18022-Precision Measurements of the Electroweak Mixing Angle in the Region of the Z pole at the Large Hadron Collider
- 2512.23992-Prospect for measurement of CP-violating parameters of B s 0 to phi gamma at the Tera Z factory