Emergent Anomalous Hall Effect from Surface States in the Altermagnet MnTe Thin Films

summary

The gist

Emergent surface states generate a large AHE driven by their strong Berry curvature near the Fermi level…

In short

Transport measurements on MnTe thin films showed conflicting anomalous Hall effects (AHE). This study resolved these discrepancies by separating bulk and surface contributions for different crystal terminations. It found that surface states within the bulk gap cause a large AHE, dominating at relevant energies. This mechanism is linked to orbital magnetization, and interface chemistry can reverse the AHE sign.

Key concepts

Anomalous Hall Effect (AHE)
A transport phenomenon where a material exhibits an electrical voltage perpendicular to both the current flow and an internal magnetic field. In this study, it was observed in MnTe films with conflicting signs and thickness-independent resistivity.
$g$-wave Fermi surface
This refers to a specific type of electronic energy surface characteristic of the bulk material. The paper indicates that although this bulk feature exists, it is not the primary driver of the observed AHE at experimental energies.
Surface states within the bulk gap
These are electronic states that exist on the surface but are located inside a region where there should be no electronic states in the material's interior (the bulk gap). These specific surface states acquire a spin polarization similar to a ferromagnet, leading to a dominant AHE contribution.
Orbital magnetization
This is the magnetic moment arising from the motion of electrons within an atom or material. The study shows that both the bulk and surface contributions to the AHE are closely tied to this small but finite out-of-plane orbital magnetization.

Terminology used across episodes

This episode discusses

The paper

Emergent Anomalous Hall Effect from Surface States in the Altermagnet MnTe Thin Films · Read on arXiv

Yufei Zhao, Saswata Mandal, Chao-Xing Liu, Binghai Yan

Department of Condensed Matter Physics, Weizmann Institute of Science · Department of Physics, The Pennsylvania State University

Transport measurements on thin films of the prototypical altermagnet MnTe have reported conflicting phenomena of anomalous Hall effects (AHE), including opposite signs and thickness-independent resistivity. Here we resolve these discrepancies by separating bulk and surface contributions to the AHE for different crystal terminations. Using first-principles calculations and symmetry-based effective models, we show that although the bulk hosts a characteristic g-wave Fermi surface, surface states within the bulk gap acquire a ferromagnet-like spin polarization and dominate the AHE at experimentally relevant Fermi energies. While the surface magnetization follows the surface spin sublattice, the resulting AHE is uniquely determined by the bulk Néel order for a given termination. Both bulk and surface contributions are closely linked to a small but finite out-of-plane orbital magnetization. Incorporating realistic interfacial chemistry further reveals that a Te capping layer can reverse the surface AHE sign relative to that on an InP substrate. Our results establish a microscopic framework for interpreting and engineering AHE responses in altermagnetic thin films through interface design.

DOI: 10.1103/5d3f-y218

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Emergent Anomalous Hall Effect from Surface States in the Altermagnet MnTe Thin Films".

Mira: Here's the gist of the paper. Emergent surface states generate a large AHE driven by their strong Berry curvature near the Fermi level, rationalizing the unusual AHE and resistivity observed in MnTe thin films Resolving Experimental Discrepancies The study resolves conflicting transport measurements on MnTe thin films by separating bulk and surface contributions to the anomalous Hall effect for different crystal terminations The researchers show that although the bulk hosts a characteristic g-wave Fermi surface, surface states within the bulk gap acquire a ferromagnet-like spin polarization and dominate the AHE at experimentally relevant Fermi energies Both bulk and surface contributions are closely linked to a small but finite out-of-plane orbital magnetization Incorporating realistic interfacial chemistry further reveals that a Te capping layer can reverse the surface AHE sign relative to that on an InP substrate Surface State Characteristics

Paper summary: Kai: We just covered how this paper resolves those conflicting transport measurements on MnTe films by looking at bulk versus surface contributions for different crystal terminations. They show that surface states inside the bulk gap get a ferromagnet-like spin polarization and those states dominate the anomalous Hall effect at experimental energies, even though the bulk has a g-wave Fermi surface.

Mira: And what I found interesting is their point about how that final polarity of the surface anomalous Hall effect is determined by the bulk Néel order for a given termination, not just what’s on the surface itself. That ties it all together conceptually.

Lev: From an engineering standpoint, if we were trying to build a device based on this, we’d need to know which termination gives us the desired sign because that depends on that bulk Néel order they mentioned.

Kai: Exactly. And they tie both the bulk and surface contributions back to a small but finite out-of-plane orbital magnetization, which is something we can try to control in our experiments.

Mira: That orbital moment connection is crucial because it’s what links the two parts of the effect together, showing it's not just one or the other dominating.

Lev: And they also used DFT calculations with VASP and the PBE functional, which is standard, but they did look at how that Fermi level relative to the bulk edge E* affects things.

Kai: They noted that their calculated carrier density at E* was much larger than what was seen experimentally in some Ref. twenty-one or Ref <ref:2603.12259#pg3>. twenty-nine, which suggests the experimental Fermi level is actually higher than the bulk bands, leading to that thickness independence they observed <ref:2603.12259#pg3>.

Mira: That discrepancy between calculation and experiment on carrier density is important because it tells us where the real physics might be sitting relative to what we model in theory.

Lev: It also mentioned that some bulk samples showed a three-dimensional carrier density around one thousand nineteen cm−three at three hundred Kelvin, which corresponds to a Fermi level zero point zero two electron volt below the bulk edge E* <ref:2603.12259#pg3,which corresponds to a Fermi level 0.02>.

Kai: So, to summarize this section, the paper argues that emergent surface states drive the AHE through Berry curvature, and that this effect is dictated by the bulk Néel order combined with interfacial chemistry like a Te capping layer.

Conclusion: Kai: So, looking at this paper, "Emergent Anomalous Hall Effect from Surface States in the Altermagnet MnTe Thin Films," the authors are basically saying that those strange transport results we saw on MnTe films—the mixed signs and thickness-independent resistivity—are not random anomalies.

Mira: They explain that these phenomena come from a combination of two things: the bulk properties and these surface states, which they show are really important for understanding the physics.

Lev: What this means for us is that when we look at thin films of altermagnets, we can’t just look at the bulk magnetism alone to understand the anomalous Hall response. We have to account for those specific surface states and how they interact with each other.

Kai: They emphasize that by carefully designing the interface, like choosing a specific capping material such as Te over InP, we can actually control the sign of this effect, which is a huge hint for future device engineering.

Mira: The implication is that understanding these surface state mechanisms through DFT and symmetry models gives us a clear path to engineering how these thin films respond to external fields.

Lev: From an experimental perspective, it suggests that thickness dependence might be less important than the specific crystal termination you choose because the surface effects can dominate in a way we haven't fully accounted for before.

Kai: It’s about moving from just observing weird numbers to building a framework where we can predict and control the response based on what’s happening at the boundary between the material and its environment.

More episodes

← Home