Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate

arXiv:2611.13300 · eess.SP · Submitted 2026-11-09 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate".

Dev: Here's the gist of the paper. This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT).

Rosa: Transducer Performance Metrics The fabricated device achieves a low resonance frequency of 33.4 kHz for airborne transduction and an extracted effective electromechanical coupling efficiency (k2eff) of 3%.

Dev: Mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement (ξstatic) of 145 nm/V and a high corresponding open-circuit sensitivity (SOC) of 1.4 mV/Pa in the audio band.

Rosa: The device exhibits an excellent k2eff alongside a high ξstatic in a compact footprint of 0.25 mm2 while achieving a moderate C0 of 17.2 pF.

Paper summary: Rosa: So wrapping up the discussion on this work, we’re looking at the title and the authors of this paper about this thickness field excited bimorph piezoelectric micromachined ultrasonic transducer in submicrometer thin-film lithium niobate.

Dev: The implication here is that they’ve managed to demonstrate a device operating at sub-one hundred kilohertz frequencies for airborne applications <ref:2611.13300#pg2>.

Rosa: They achieved an extracted effective electromechanical coupling efficiency of three percent and a static capacitance C naught density of seventeen pico farads <ref:2611.13300#pg2>.

Dev: This means they have a resonance frequency of three thirty point four kilohertz for airborne transduction, which is relatively low <ref:2611.13300#pg2>.

Rosa: The paper shows that the lithium niobate device achieves a comparable static displacement while showcasing a significantly higher open circuit sensitivity <ref:2611.13300#pg2>.

Dev: This positions lithium niobate as a sensor and bidirectional transducer platform for airborne applications <ref:2611.13300#pg2>.

Taro: The main thing is that the study underscores the potential of the thickness field excited P three F lithium niobate transducer platform by pinpointing those discrepancies between their simulation and their measured results <ref:2611.13300#pg2>.

Rosa: So, while it shows promise, they’ve pointed out that the device hasn't yet realized its full potential because of those boundary condition shifts <ref:2611.13300#pg2>.

Dev: That means future work needs to focus on minimizing that effect by enhancing C b compared to the membrane compliance <ref:2611.13300#pg2>.

Taro: It’s a design challenge where matching the physical setup with the ideal model becomes important for getting that high performance <ref:2611.13300#pg2>.

Rosa: So, this paper presents the first demonstration of a P three F lithium niobate based submicrometer thick clamped-plate piezoelectric transducer operating at sub-one hundred kilohertz frequencies for airborne applications <ref:2611.13300#pg1>.

Conclusion: Rosa: So we’re wrapping up this look at this paper about their thickness field excited bimorph piezoelectric micromachined ultrasonic transducer in submicrometer thin-film lithium niobate, and what it means for things.

Dev: Basically, they built a device that’s thinner than a micrometer using lithium niobate, and it works at very low frequencies for airborne stuff.

Rosa: Right. They achieved this with a resonance frequency of thirty-three point four kilohertz for the sound it makes in the air.

Dev: And they got an effective electromechanical coupling efficiency of three percent, which is pretty solid for this kind of setup.

Taro: What’s interesting is that they managed to get a high static displacement while still having a moderate flat-band sensitivity.

Rosa: That’s the core finding here, because it shows this lithium niobate platform can handle both large areas and good sensitivity at once.

Dev: It positions lithium niobate as a potential sensor and even a bidirectional transducer platform for airborne uses.

Taro: But they also admit there are still some issues. The simulation didn't match the actual measurements perfectly, so the device hasn't reached its full potential yet.

Rosa: Exactly. They found that the measured coupling efficiency was lower than what their computer models predicted, which messed with those static displacement numbers they were hoping for.

Dev: So, future work needs to focus on fixing those boundary condition shifts they saw in the simulation versus reality by improving how that material interacts with its surroundings.

Taro: It's a design challenge where matching the physical setup to the ideal model becomes crucial if you want to get those high performance numbers.

Rosa: So, this paper shows a promising path for using these ultra-thin lithium niobate devices in real-world applications, but it also sets up a clear path for what needs to be fixed next.

Vakhtang Chulukhadze, Jiajun Huang, Zihuan Liu, Will Leskowitz, Tzu-Hsuan Hsu, Yuchen Ma, Udit Rawat, Yao Yu, Bichoy Bahr, Neal A. Hall, Á Ruochen Lu

University of Texas at Austin Department of Electrical and Computer Engineering · Kilby Labs Texas Instruments

eess.SP

Submitted: 2026-11-09

Updated: 2026-11-09

Comments: 8 pages, 11 figures

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 96/100

The gist: This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT).

Key concepts

Thickness-Field-Excited (TFE) Transducer
This is a type of piezoelectric transducer where the excitation mechanism involves using an electric field across the thickness of a very thin material. In this case, it uses a submicrometer-thick layer of lithium niobate to generate ultrasonic waves, allowing for very compact device designs.
Effective Electromechanical Coupling Efficiency (k2eff)
This metric quantifies how efficiently the piezoelectric material converts electrical energy into mechanical energy and vice versa. A value of 3% indicates a moderate but respectable efficiency, which is important for determining the transducer's overall performance in converting signals.
Quasi-static Peak Out-of-Plane Displacement (ξstatic)
This measurement describes how much the device physically moves when subjected to a specific voltage. A high value of 145 nm/V indicates excellent mechanical response, which is crucial for applications requiring high sensitivity to small forces or vibrations.

Terminology

Summary

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). p. 0

Where the paper says it

1 Thickness-Field-Excited Bimorph Piezoelectric Micromachined Ultrasonic Transducer in Submicrometer Thin-Film Lithium Niobate Vakhtang Chulukhadze, Student Member, IEEE, Jiajun Huang, Zihuan Liu, Student Member, IEEE, Will Leskowitz, Tzu-Hsuan Hsu, Member, IEEE, Yuchen Ma, Student Member, IEEE, Udit Rawat, Member, IEEE, Yao Yu, Bichoy Bahr, Member, IEEE, Neal A. Hall, and Ruochen Lu, Senior Member, IEEE 1 2 3 4 5 6 7 8 9 Abstract—This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT).

Transducer Performance Metrics

The fabricated device achieves a low resonance frequency of 33.4 kHz for airborne transduction and an extracted effective electromechanical coupling efficiency (k2eff) of 3%. p. 0

Where the paper says it

4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency (k 2 eff ) of 3% and a moderate static capacitance C0 of 17 pF.

Mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement (ξstatic) of 145 nm/V and a high corresponding open-circuit sensitivity (SOC) of 1. p. 0
Where the paper says it

Its electrical measurements reveal an extracted effective electromechanical coupling efficiency (k 2 eff ) of 3% and a moderate static capacitance C0 of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement (ξstatic) of 145 nm/V and a high corresponding open-circuit sensitivity (SOC) of 1.

4 mV/Pa in the audio band. p. 0
Where the paper says it

Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement (ξstatic) of 145 nm/V and a high corresponding open-circuit sensitivity (SOC) of 1. 4 mV/Pa in the audio band.

The device exhibits an excellent k2eff alongside a high ξstatic in a compact footprint of 0. p. 4
Where the paper says it

The measurement yields a high ξstatic of 145 nm/V, which will be used to evaluate device performance within the audio band. In tandem, the measured results indicate that the device obtains an excellent transmission efficiency and exhibits a low resonance frequency ideal for ultrasonic and audio-band applications while featuring an exceedingly compact footprint of 0.

25 mm2 while achieving a moderate C0 of 17. p. 3
Where the paper says it

The simulated device demonstrates an excellent k 2 eff alongside a high ξstatic in a compact footprint of 0. 25 mm2 while achieving a moderate C0 of 17.

2 pF.

Design and Material Selection

The design utilized a submicrometer-thick (670 nm) active layer to demonstrate TFE P3F transducers with high compliance and a compact footprint, optimal for sub-100-kHz airborne applications. Among commercially available LN material cuts with high relevant electromechanical coupling tensor components (e31,eff and e32,eff), 36Y and 128Y LN stand out as the primary candidates. p. 2

Where the paper says it

The process began with LN orientation selection for TFE flexural-mode operation. Among commercially available LN material cuts with high relevant electromechanical coupling tensor components (e31,eff and e32,eff), 36Y and 128Y LN stand out as the primary candidates, as shown in Table II.

The lower εii,eff of 128Y LN yields a higher receiving FoM, leading to the adoption of 128Y LN for the TFE P3F LN transducer. p. 2
Where the paper says it

Here, εii,eff and the ratio between eij,eff and εii,eff are used as secondary performance metrics, where εii,eff describes the C0-density and the ratio describes the platform’s open-circuit sensitivity, acting as another receiving performance metric. The comparison in Table II shows that while 36Y LN and 128Y LN exhibit electromechanical coupling tensor components of similar magnitude, the lower εii,eff of 128Y LN yields a higher receiving FoM, leading to the adoption of 128Y LN for the TFE P3F LN transducer.

The design process closely followed that of the LFE counterpart in [18], using parametric sweeps while tracking the effective electromechanical coupling efficiency (k2eff) and C0 defined as k2eff = Φ 2Cad / C0. p. 2
Where the paper says it

4(a) and (b), respectively, with the crystal axes and the key design parameters labeled. The design process closely followed that of the LFE counterpart in [18], using parametric sweeps while tracking the effective electromechanical coupling efficiency (k 2 eff) and C0 defined as: k 2 eff = Φ 2Cad C0 , (1a) C0 = Im(Y ) ω , (1b) where Φ is the turns ratio of the pressure-charge transformer, Cad is the acoustic compliance of the membrane, Y is the

Fabrication and Measurement Details

The transducers were fabricated using a 670-nm-thick 128Y P3F LN wafer, provided by NGK Corporation. The fabrication involved evaporating 50 nm of gold (Au) top electrodes with a 10-nm-thick chromium (Cr) adhesion layer. p. 3

Where the paper says it

FABRICATION AND MEASUREMENT The transducers were fabricated using a 670-nm-thick 128Y P3F LN wafer, provided by NGK Corporation. The fabrication began by evaporating 50 nm of gold (Au) top electrodes with a 10-nm-thick chromium (Cr) adhesion layer, introducing minimal mass loading while featuring high conductivity.

The device was measured with a Zurich MFIA impedance analyzer and a Polytec laser Doppler vibrometer (LDV), with the results shown in Figs. p. 3
Where the paper says it

6(a) and (b). The fabricated device was measured with a Zurich MFIA impedance analyzer and a Polytec laser Doppler vibrometer (LDV), with the results shown in Figs.

7 and 8 respectively. p. 2
Where the paper says it

Consequently, the top and the cross-sectional views of the thin-film TFE P3F LN transducer are shown in Fig. 4(a) and (b), respectively, with the crystal axes and the key design parameters labeled.

Comparative Analysis

The extracted device performance is compared to SoA airborne piezoelectric transducers with a resonance frequency below 100 kHz in Table IV. The LN device is the most compact of the surveyed flexural-mode clamped membrane transducers with a sub-100-kHz resonance frequency, while also featuring the highest SOC alongside a moderate ξstatic comparable to high-transmiteff material platforms, such as PZT. p. 5

Where the paper says it

The comparison focuses on evaluating the balance between ξstatic and audioband sensitivity metrics. The comparison highlights that the presented LN device is the most compact of the surveyed flexural-mode clamped membrane transducers with a sub-100- kHz resonance frequency, while also featuring the highest SOC alongside a moderate ξstatic comparable to high-transmitefficiency material platforms, such as PZT.

The presented TFE P3F LN results highlight the platform’s ability to realize large-area membranes with a high k2eff, enabling a high SOC alongside a high ξstatic. p. 5
Where the paper says it

Importantly, the SSC can be further enhanced by exchanging the floating bottom electrode architecture for its grounded version, maximizing C0 density. The presented TFE P3F LN results highlight the platform’s ability to realize large-area membranes with a high k 2 eff, enabling a high SOC alongside a high ξstatic.

Limitations and Future Work

The analysis of the obtained measurements against the idealized simulation in Fig. 5 shows that the device has not yet realized its full potential. p. 6

Where the paper says it

While the fabricated device exhibits high performance compared with incumbent airborne PMUTs, the analysis of the obtained measurements against the idealized simulation in Fig. 5 shows that the device has not yet realized its full potential.

The comparison between Figs. p. 4
Where the paper says it

Cavity Effects In an effort to investigate back-cavity-induced acoustic effects, the elevated pedestal was exchanged for a flat metallic substrate. The transducer showed a significant change in performance and resonant behavior, with the comparison shown in Figs.

5 and 7 shows that the measured device obtained a lower k2eff than predicted, leading to a significantly reduced ξpeak and ξstatic. p. 6
Where the paper says it

The comparison between Figs. 5 and 7 shows that the measured device obtained a lower k 2 eff than predicted, leading to a significantly reduced ξpeak and ξstatic.

The contrast between the ideal simulated mode shape of a clamped membrane and the measured data indicates that the fabricated LN device experiences a fundamental shift in boundary conditions. p. 6
Where the paper says it

The LDV-measured mode shape offers a direct explanation when compared with its simulated version, shown in Fig. The contrast between the ideal simulated mode shape of a clamped membrane and the measured data indicates that the fabricated LN device experiences a fundamental shift in boundary conditions, demonstrating a flexural mode shape with a significantly wider displacement distribution in the flat band, and a narrower shape at resonance.

Future design iterations must aim to either minimize its effect by enhancing Cb compared to the membrane compliance, or closely match them. p. 5
Where the paper says it

Hence, the back cavity plays a critical role in determining the transducer’s performance when the membrane compliance is sufficiently high. Future design iterations must aim to either minimize its effect by enhancing Cb compared to the membrane compliance, or closely match them [4], [33].

Conclusion

This work presents the first demonstration of a P3F LN-based submicrometer-thick, clamped-plate piezoelectric transducer operating at sub-100-kHz frequencies for airborne applications. The device achieves a k2eff of 3% with a C0 of 17 pF, a resonance frequency of 33. p. 6

Where the paper says it

The device achieves an exceedingly compact footprint due to the high film compliance achieved by the large-area, thin-film membrane, which consequently leads to high electromechanical performance in conjunction with the high e31,eff in single-crystal LN. As a result, the fabricated device demonstrates a k 2 eff of 3% with a C0 of 17 pF, a resonance frequency of 33.

4 kHz, and yields a high ξstatic, as well as a moderate extracted flat-band SSC and a high flat-band SOC. p. 6
Where the paper says it

As a result, the fabricated device demonstrates a k 2 eff of 3% with a C0 of 17 pF, a resonance frequency of 33. 4 kHz, and yields a high ξstatic, as well as a moderate extracted flat-band SSC and a high flat-band SOC.

The LN device achieves a comparable ξstatic while showcasing a significantly higher SOC, positioning LN as a SoA sensor and bidirectional transducer platform. p. 6
Where the paper says it

4 kHz, and yields a high ξstatic, as well as a moderate extracted flat-band SSC and a high flat-band SOC. Compared with SoA airborne piezoelectric transducers, the LN device achieves a comparable ξstatic while showcasing a significantly higher SOC, positioning LN as a SoA sensor and bidirectional transducer platform.

The presented study underscores further potential of the TFE P3F LN transducer platform by pinpointing discrepancies between the simulation and the measured results. p. 6
Where the paper says it

Compared with SoA airborne piezoelectric transducers, the LN device achieves a comparable ξstatic while showcasing a significantly higher SOC, positioning LN as a SoA sensor and bidirectional transducer platform. Importantly, the presented study underscores further potential of the TFE P3F LN transducer platform by pinpointing discrepancies between the simulation and the measured results, outlining clear next steps in order to realize the potential performance of the P3F LN piezoelectric transducer platform.

ACKNOWLEDGMENT

The authors would like to thank Dr. Todd Bauer for helpful discussions. p. 6

Where the paper says it

ACKNOWLEDGMENT The authors would like to thank Dr. Todd Bauer for helpful discussions.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Optimize material selection by prioritizing lithium niobate cuts like 128Y LN due to their lower epsilonii,eff of 128Y LN yields a higher receiving FoM compared to other candidates in Table II. This allows the AI system to select the most efficient piezoelectric substrate for a given performance target.

  2. Incorporate boundary condition analysis into simulation models by using the results from Fig 11, which shows that the fabricated device does not follow the conventional mode shape of a clamped plate, to refine how displacement distributions are modeled. This improves predictive accuracy for actual device behavior under real-world conditions.

  3. Develop a performance prediction module that accounts for system-level effects by using the LDV measurement analysis: SSC with the back-cavity effect present is found to be 12.5 fC/Pa at 5 kHz, while SOC is 0.78 mV/Pa at the same frequency, presenting a twofold reduction from the original measurement. This enables more realistic sensitivity estimations for different mounting scenarios.

  4. Enhance design optimization by implementing a feedback loop to track the effective electromechanical coupling efficiency (k2 eff) and C0 defined as: k2 eff = Phi squared Cad / C0 during parametric sweeps, as described in the text. This allows the system to iterate rapidly toward designs that maximize performance metrics simultaneously.

  5. Create a comparative analysis tool that contrasts the TFE P3F LN platform against State-of-the-Art (SoA) devices by explicitly comparing the presented LN device is the most compact of the surveyed flexural-mode clamped membrane transducers with a sub-100-kHz resonance frequency, while also featuring the highest SOC alongside a moderate ξstatic. This provides clear benchmarks for new design evaluations.

Abstract

This work presents the first demonstration of a submicrometer-thick thickness-field-excited (TFE) lithium niobate (LN) flexural-mode piezoelectric micromachined ultrasonic transducer (PMUT). A 670-nm-thick bilayer periodically poled piezoelectric film (P3F) 128Y LN is used to demonstrate a suspended membrane with an area of 0.25 mm squared, achieving a low resonance frequency of 33.4 kHz for airborne transduction. Its electrical measurements reveal an extracted effective electromechanical coupling efficiency (k eff squared) of 3% and a moderate static capacitance C 0 of 17 pF. Meanwhile, mechanical measurements using a laser Doppler vibrometer (LDV) yield a high quasi-static peak out-of-plane displacement (ξ static) of 145 nm/V and a high corresponding open-circuit sensitivity (S OC) of 1.4 mV/Pa in the audio band. The fabricated device is compared with state-of-the-art (SoA) airborne piezoelectric transducers with sub-100-kHz resonance frequencies, underscoring the potential of the TFE P3F LN transducer platform by simultaneously demonstrating strong actuation capability while featuring high sensitivity.

Sources

Related papers