Electromagnetically Consistent Monostatic ISAC Beamforming: Mutual Coupling, Active Mismatch and Tx-Rx Leakage in Compact Dipole Arrays

arXiv:2611.08331 · eess.SP · Submitted 2026-11-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "Electromagnetically Consistent Monostatic ISAC Beamforming".

Dev: Here's the gist of the paper. Beamforming for integrated sensing and communication (ISAC) is usually designed on ideal array manifolds with a norm constraint on the transmit signal.

Rosa: Full-wave evaluation shows that coupling-unaware designs miss their SINR targets by up to 6.2 dB and drive amplifiers to an equivalent VSWR above 3.3 at small spacings.

Dev: Pruning redundant reasoning tokens The paper addresses the limitations of ideal array manifold designs in compact monostatic transceiver systems by incorporating three key antenna effects: distorted embedded patterns, beam-dependent active mismatch at power amplifiers, and transmit-to-receive leakage that raises the radar noise floor.

Rosa: The authors build a multiport scattering model of a shared-aperture dipole array directly from method-of-moments simulations to formulate a Cramer–Rao bound minimizing ISAC beamformer with multiuser SINR constraints, perport active reflection constraints and a leakage budget, solved as a semidefinite program with a one-dimensional budget search.

Paper summary: Rosa: To wrap up what we've seen so far, this paper "Electromagnetically Consistent Monostatic ISAC Beamforming: Mutual Coupling, Active Mismatch and Tx-Rx Leakage in Compact Dipole Arrays" is really focused on fixing the limitations of ideal array manifold designs Rosa. They address those three antenna effects mentioned earlier: distorted embedded patterns, beam-dependent active mismatch at the power amplifiers, and that transmit to receive leakage which raises the radar noise floor Rosa.

Dev: The thesis is that they build a multiport scattering model of a shared aperture dipole array directly from method-of-moments simulations to formulate a Cramer Rao bound minimizing ISAC beamformer that includes SINR and power constraints, plus limits on perport active reflection and this Tx to Rx leakage linked to the radar noise floor through some self interference cancellation budget Dev.

Taro: Basically, they set up a semidefinite program with an outer one-dimensional search to solve this problem Taro. They are minimizing the Cramer Rao bound subject to per-user SINR targets, power budgets, a perport active reflection limit called Gamma max which is the VSWR limit, and a Tx to Rx leakage budget called eta Taro.

Rosa: The key takeaway is that this formulation links the leakage directly to the radar noise floor via a self interference cancellation budget Rosa. This helps them maximize the Fisher information, which is basically what you want in these sensing and communication systems Rosa.

Dev: The results show that when they solve this problem, their design meets all those constraints for element spacings from zero point two lambda to zero point five lambda Dev. They quantify the SINR loss, the power amplifier mismatch, and the sensing loss for both coupling-unaware and pattern-only coupling-aware designs Dev.

Taro: And they show that this proposed design has a gain towards its target that is three point seven decibels lower than what you'd get from just focusing on the power amplifiers Taro.

Rosa: The paper also shows that their proposed design keeps its SINRs within zero point zero five decibels of the target and its leakage at negative thirty-seven point four decibels, which means the beam-domain leakage null is robust to the change of solver and feed model Rosa.

Dev: However, they also note that while this leakage null is stable, the active reflection part depends on the self terms in their model Dev. That part moves a bit when you change the simulation tool Dev.

Taro: So, what does that mean for real-world deployment? It means you need to be careful about how well your feed model captures those self terms because that affects the active reflection budget Taro.

Conclusion: Rosa: So, looking at the title "Electromagnetically Consistent Monostatic ISAC Beamforming: Mutual Coupling, Active Mismatch and Tx-Rx Leakage in Compact Dipole Arrays", it tells you everything about what they were tackling Rosa. It’s not just one problem, it’s coupling, mismatch, and leakage all at once Rosa.

Dev: It really is a comprehensive look at how these three things interact in compact systems where you have to pack antennas close together Dev. The implication is that you can't just optimize for the beam pattern alone anymore; you have to account for the load seen by the power amplifiers and the noise floor of your receiver Dev.

Taro: So what does this mean practically? It means that if you're designing a small transceiver, you need to ensure your system doesn't just look good in isolation but that it also handles how those components interact with each other Taro.

Rosa: Exactly. The paper shows that the leakage null they found is robust, which is good because it means the fundamental design survives changes in how you model things Rosa. But you still have to manage that active reflection part carefully because it depends on feed details Rosa.

Dev: So for future work, they mention a few things: working with dipoles over a ground plane on a substrate, moving to wideband operation like OFDM, making designs robust against fabrication tolerances, and doing measurements on a physical prototype Dev.

Taro: The paper states that the leakage constraint is seven f at the physical layout shows that the proposed beamformer tapers the transmit currents towards the gap and phases them so they cancel their fields on the receive side Taro. That's a very concrete mechanism Taro.

Rosa: So, to wrap up, this paper gives us a specific design that satisfies every constraint and also radiates more of the power amplifier power at zero point three lambda compared to other designs Rosa. This is what we have here for now >

Stylianos D. Asimonis, Christos Tselios, Dimitrios Tyrovolas, Ilias Politis, George K. Karagiannidis

University of Patras · Enebula BV · University of Peloponnese Department of Informatics and Telecommunications Institute Research Centre ATHENA Research Centre Aristotle University of Thessaloniki Department of Electrical and Computer Engineering

eess.SP

Submitted: 2026-11-05

Updated: 2026-11-05

Comments: 6 pages, 9 figures, 2 tables. Submitted to IEEE ICC 2027

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 72/100

The gist: Beamforming for integrated sensing and communication (ISAC) is usually designed on ideal array manifolds with a norm constraint on the transmit signal.

Key concepts

Port-level scattering model
This is a mathematical tool built directly from simulations (method-of-moments) to describe how electromagnetic waves interact at the ports of an antenna array. It allows researchers to quantify physical quantities like active reflection, Tx-Rx leakage, and radiated power in a way that is consistent across different simulation methods.
Active reflection
This refers to the unwanted signal reflected back from the antenna elements themselves, which is caused by mismatches between the antenna elements and their driving power amplifiers. The optimization process seeks to minimize this effect while maintaining good communication performance.
Tx–Rx leakage budget
This concept deals with how much of the transmitted signal unintentionally leaks into the receiver's path, raising the radar noise floor. The proposed design actively manages this leakage by tapering and phasing currents, effectively reducing interference at the receiver.
Root Cramer-Rao Bound (CRB)
The CRB is a measure of the fundamental limit on how accurately a signal can be estimated. The optimization aims to minimize this bound subject to constraints like SINR targets and power budgets, which directly translates to better achievable performance for sensing and communication tasks.

Terminology

Summary

Beamforming for integrated sensing and communication (ISAC) is usually designed on ideal array manifolds with a norm constraint on the transmit signal. p. 0

Where the paper says it

Aristotle University of Thessaloniki 54124 Thessaloniki, Greece geokarag@auth. gr Abstract—Beamforming for integrated sensing and communication (ISAC) is usually designed on ideal array manifolds with a norm constraint on the transmit signal.

Full-wave evaluation shows that coupling-unaware designs miss their SINR targets by up to 6. p. 0
Where the paper says it

We build a multiport scattering model of a shared-aperture dipole array directly from method-of-moments simulations and use it to formulate a Cramer-Rao bound minimizing ISAC beamformer with multiuser SINR constraints, perport active reflection constraints and a leakage budget, solved as a semidefinite program with a one-dimensional budget search. Full-wave evaluation shows that coupling-unaware designs miss their SINR targets by up to 6.

2 dB and drive amplifiers to an equivalent VSWR above 3. p. 0
Where the paper says it

Full-wave evaluation shows that coupling-unaware designs miss their SINR targets by up to 6. 2 dB and drive amplifiers to an equivalent VSWR above 3.

3 at small spacings. p. 0
Where the paper says it

2 dB and drive amplifiers to an equivalent VSWR above 3. 3 at small spacings.

Pruning redundant reasoning tokens

The paper addresses the limitations of ideal array manifold designs in compact monostatic transceiver systems by incorporating three key antenna effects: distorted embedded patterns, beam-dependent active mismatch at power amplifiers, and transmit-to-receive leakage that raises the radar noise floor. The authors build a multiport scattering model of a shared-aperture dipole array directly from method-of-moments simulations to formulate a Cramer–Rao bound minimizing ISAC beamformer with multiuser SINR constraints, perport active reflection constraints and a leakage budget, solved as a semidefinite program with a one-dimensional budget search. p. 0

Where the paper says it

In a compact monostatic transceiver this hides three antenna effects: distorted embedded patterns, beam-dependent active mismatch at the power amplifiers, and transmit-to-receive leakage that raises the radar noise floor. We build a multiport scattering model of a shared-aperture dipole array directly from method-of-moments simulations and use it to formulate a Cramer-Rao bound minimizing ISAC beamformer with multiuser SINR constraints, perport active reflection constraints and a leakage budget, solved as a semidefinite program with a one-dimensional budget search.

How the training signal is built

The transmitted waves are modeled as the sum of user symbols and a dedicated sensing signal. The total covariance is defined as R = k Wk + Rs, where Wk = wkwHk, and tr(R) represents the total PA output power. p. 1

Where the paper says it

Communication and Sensing Signals The transmitted waves are x = PK k=1 wksk +xs, where sk are unit-power user symbols and xs is a dedicated sensing signal with covariance P Rs. The total covariance is R = k Wk + Rs, Wk = wkwH k , and tr(R) is the total PA output power.

User k at azimuth ϕk receives a signal hk = √βk u(ϕk), where βk is the path gain. p. 1
Where the paper says it

The total covariance is R = k Wk + Rs, Wk = wkwH k , and tr(R) is the total PA output power. User k at azimuth ϕk receives over a line-ofsight channel hk = √ βk u(ϕk), where βk is the path gain, so that SINRk = hkWkh H P k j̸=k hkWjh H k + hkRsh H k + σ 2 c .

For sensing, the received signal Ys is modeled as Ys = α A(θ)X + NSI + N, where A(θ) = v(θ)u(θ). p. 1
Where the paper says it

(3) For sensing, a point target at azimuth θ produces at the Rx ports, over L snapshots, Ys = α A(θ)X + NSI + N, A(θ) = v(θ)u(θ), (4) where |α| 2 = λ 2σRCS/((4π) 3 r 4 ) follows the radar equation and N is thermal noise of power σ 2 per port. The leaked signal SRTx is first reduced by analog and digital SIC by C dB [8].

Where the gains come from

The optimization problem minimizes the CRB subject to constraints that include per-user SINR targets, PA power budgets, a per-port active reflection limit (VSWR limit), and a Tx–Rx leakage budget linked to the radar noise floor through a self-interference cancellation (SIC) budget. The proposed design meets all targets for spacings from 0. p. 0

Where the paper says it

For spacings from 0. 5 wavelengths, the proposed design meets all targets with an equivalent VSWR below 2 and lowers the root Cramer-Rao bound by 32 to 53 percent for 80 dB of selfinterference cancellation and by a factor of 3.

3 to 0.5 wavelengths with an equivalent VSWR below 2 and lowers the root Cramer-Rao bound by 32 to 53 percent for 80 dB of self-interference cancellation. p. 0
Where the paper says it

For spacings from 0. 5 wavelengths, the proposed design meets all targets with an equivalent VSWR below 2 and lowers the root Cramer-Rao bound by 32 to 53 percent for 80 dB of selfinterference cancellation and by a factor of 3.

Hardware metrics

The full-wave evaluation quantifies the SINR loss, PA mismatch, and sensing loss for coupling-unaware and pattern-only coupling-aware designs, highlighting the gains of the proposed design. The proposed design has a gain towards the target is 3. p. 2

Where the paper says it

The PA design restores the SINRs and the main beam. The proposed design has a gain towards the target is 3.

7 dB lower than PA and places a strong lobe around 145◦, away from the Rx subarray (which lies towards ϕ = 0◦). p. 2
Where the paper says it

The proposed design has a gain towards the target is 3. 7 dB lower than PA and it places a strong lobe around 145◦ , away from the Rx subarray (which lies towards ϕ = 0◦ ).

Furthermore, this beam reduces the Tx–Rx leakage from −16. p. 2
Where the paper says it

7 dB lower than PA and it places a strong lobe around 145◦ , away from the Rx subarray (which lies towards ϕ = 0◦ ). This beam reduces the Tx–Rx leakage from −16.

5 dB to −37.5 dB relative to PT, which brings the residual SI per Rx port from −75. p. 2
Where the paper says it

5 dB to −37. 5 dB relative to PT, which brings the residual SI per Rx port from −75.

5 dBm, 9.9 dB above thermal noise, to −96. p. 1
Where the paper says it

User k at azimuth ϕk receives over a line-ofsight channel hk = √ βk u(ϕk), where βk is the path gain, so that SINRk = hkWkh H P k j̸=k hkWjh H k + hkRsh H k + σ 2 c . (3) For sensing, a point target at azimuth θ produces at the Rx ports, over L snapshots, Ys = α A(θ)X + NSI + N, A(θ) = v(θ)u(θ), (4) where |α| 2 = λ 2σRCS/((4π) 3 r 4 ) follows the radar equation and N is thermal noise of power σ 2 per port.

5 dBm, below thermal noise. p. 2
Where the paper says it

9 dB above thermal noise, to −96. 5 dBm, below thermal noise.

Spacing

The root-CRB versus element spacing shows that for d ≥ 0.3λ, the proposed design is consistently the best, reducing the root-CRB of the best benchmark by 32–53% at C = 80 dB. p. 4

Where the paper says it

For d ≥ 0. 3λ, the proposed design is consistently the best, reducing the rootCRB of the best benchmark by 32–53% at C = 80 dB and by 3.

Even at d = 0. p. 4
Where the paper says it

6× at C = 70 dB. Even at d = 0.

5λ, where coupling is often considered negligible, CU misses the SINR target by 0. p. 4
Where the paper says it

Even at d = 0. 5λ, where coupling is often considered negligible, CU misses the SINR target by 0.

7 dB and the proposed design improves the root-CRB by 32% at C = 80 dB because leakage still limits the receiver. p. 4
Where the paper says it

5λ, where coupling is often considered negligible, CU misses the SINR target by 0. 7 dB and the proposed design improves the root-CRB by 32% at C = 80 dB, because leakage still limits the receiver.

Below 0.3λ, compactness must be paid for by matching or decoupling networks. p. 4
Where the paper says it

2λ no design meets both the SINR targets and the 2:1 VSWR limit. Here compactness must be paid for by matching or decoupling networks.

Conclusion

The paper demonstrates that the antenna array determines not only the radiated beam but also the load seen by the PAs and the noise floor of the radar receiver. The leakage null is robust to solver and feed model changes, while active reflection depends on feed details and calls for a small design margin. p. 5

Where the paper says it

6× at 70 dB, for spacings from 0. An independent FDTD model of the final layout confirms that the leakage null is robust to the solver and feed model, whereas the active reflection depends on the feed details and calls for a small design margin.

The proposed design satisfies every constraint and also radiates more of the PA power (88. p. 3
Where the paper says it

design fixes the mismatch but, without (7f), it moves energy into the leakage path and its CRB is the worst of all. The proposed design satisfies every constraint and also radiates more of the PA power (88.

9% versus 82. p. 3
Where the paper says it

50 Element spacing d/λ −30 −25 −20 −15 −10 −5 0 Magnitude (dB) adjacent pair |S4,5| passive reflection |S4,4| Tx→Rx leakage, broadside beam (a) 0 ◦ 30◦ 60◦ 90◦ 120◦ 150◦ 180◦ Azimuth φ −10 −5 0 5 Realized gain (dBi) isolated dipole Tx element 1 Tx element 4 Tx element 8 (b) Fig. (a) Coupling between adjacent elements, passive reflection of an inner element and total Tx–Rx leakage of a broadside beam versus spacing.

2% for PA at 0.3λ). Future work will include dipoles over a ground plane on a substrate, wideband (OFDM) operation, robust designs against fabrication tolerances, and measurements on a prototype. p. 5
Where the paper says it

An independent FDTD model of the final layout confirms that the leakage null is robust to the solver and feed model, whereas the active reflection depends on the feed details and calls for a small design margin. Future work will include dipoles over a ground plane on a substrate, wideband (OFDM) operation, robust designs against fabrication tolerances, and measurements on a prototype.

The paper is titled Electromagnetically Consistent Monostatic ISAC Beamforming: Mutual Coupling, Active Mismatch and Tx–Rx Leakage in Compact Dipole Arrays. The authors build a port-level scattering model of a sharedaperture Tx/Rx dipole array directly from NEC-2 methodof-moments simulations. p. 0

Where the paper says it

This paper closes that gap with a hardware-grounded approach. Our contributions are: • We build a port-level scattering model of a sharedaperture Tx/Rx dipole array directly from NEC-2 methodof-moments simulations [13], giving realized embedded patterns, active reflections and Tx–Rx leakage as linear functions of the PA waves.

This model exposes three hardware quantities that are linear in x: Active reflection, Tx–Rx leakage, and Radiated power. p. 1
Where the paper says it

By reciprocity, the receive manifold v(ϕ) ∈ C NR is given by the last NR columns of the same expression. The model exposes three hardware quantities that are linear in x: • Active reflection.

The budget η trades the Fisher information that can be delivered by the Tx subarray against the noise floor at the Rx subarray. p. 2
Where the paper says it

This leaves R unchanged, and therefore (7b), (7d)–(7f) and every SINR are preserved. The budget η trades the Fisher information that can be delivered by the Tx subarray against the noise floor at the Rx subarray.

The ranking of all designs is thus the same in both solvers, which supports the conclusions of Section IV. p. 4
Where the paper says it

87◦ , which is 56% below the PA design optimized on the same data; the latter still drives a PA to a VSWR of 2. The relative ranking of all designs is thus the same in both solvers, which supports the conclusions of Section IV.

The proposed design keeps its SINRs within 0. p. 4
Where the paper says it

The upper part of Table II replays the beamformers designed on the NEC-2 model, without any change, on the FDTD model, which here plays the role of the “real” array. The proposed design keeps its SINRs within 0.

05 dB of the target and its leakage at −37. p. 1
Where the paper says it

d Tx subarray (NT PAs) Rx subarray (NR LNAs) SRTx leakage user 1 user K target echo PA waves x reflections STTx |Γ¯n| ≤ Γmax Fig. Monostatic ISAC transceiver with a shared-aperture collinear array of z-directed dipoles.

4 dB, i.e., the beam-domain leakage null is robust to the change of solver and feed model. p. 4
Where the paper says it

05 dB of the target and its leakage at −37. , the beam-domain leakage null is robust to the change of solver and feed model, because it depends on the mutual terms, which both solvers agree on.

The quantity that moves is the active reflection, which depends on the self terms. p. 4
Where the paper says it

6(c) shows that the patterns are practically unchanged. The quantity that moves is the active reflection, which depends on the self terms: the largest VSWR of the proposed design rises from 2.

The largest VSWR of the proposed design rises from 2. p. 4
Where the paper says it

6(c) shows that the patterns are practically unchanged. The quantity that moves is the active reflection, which depends on the self terms: the largest VSWR of the proposed design rises from 2.

00 to 2.18. The leakage constraint (7f) at work on the physical layout shows that the proposed beamformer tapers the Tx currents towards the gap and phases them so that their fields cancel on the Rx side. p. 4
Where the paper says it

4 dB of the strip-current power. The proposed beamformer tapers the Tx currents towards the gap (the eighth dipole is 13 dB below the first) and phases them so that their fields cancel on the Rx side: the first Rx dipole drops to −29.

The values for Rx share to −35. p. 4
Where the paper says it

8 dB and the Rx share to −35. These values agree with the port-level leakage of Table II (−16.

1 dB agree with the port-level leakage of Table II (−16. p. 4
Where the paper says it

8 dB and the Rx share to −35. These values agree with the port-level leakage of Table II (−16.

9 and −37.4 dB). The FDTD scattering matrix is reciprocal to within 0. p. 4
Where the paper says it

Agreement of the two solvers. The FDTD scattering matrix is reciprocal to within 0.

25%. The mutual terms agree with NEC-2 over a 35 dB range (to within 1. p. 4
Where the paper says it

The FDTD scattering matrix is reciprocal to within 0. 6(b) shows that the mutual terms agree with NEC-2 over a 35 dB range (to within 1.

7 dB for all 240 mutual terms). p. 4
Where the paper says it

6(b) shows that the mutual terms agree with NEC-2 over a 35 dB range (to within 1. 7 dB for all 240 mutual terms), from −8.

The upper part of Table II replays the beamformers designed on the NEC-2 model, without any change, on the FDTD model. p. 4
Where the paper says it

Model mismatch. The upper part of Table II replays the beamformers designed on the NEC-2 model, without any change, on the FDTD model, which here plays the role of the “real” array.

The proposed design again meets every constraint, selects the same leakage budget (−37. p. 4
Where the paper says it

The lower part of Table II solves (7) directly on the FDTD data. The proposed design again meets every constraint, selects the same leakage budget (−37.

5 dB) and reaches 0. p. 4
Where the paper says it

The quantity that moves is the active reflection, which depends on the self terms: the largest VSWR of the proposed design rises from 2. 18, and the PA design still reaches 3.

87◦. The relative ranking of all designs is thus the same in both solvers, which supports the conclusions of Section IV. p. 4
Where the paper says it

87◦ , which is 56% below the PA design optimized on the same data; the latter still drives a PA to a VSWR of 2. The relative ranking of all designs is thus the same in both solvers, which supports the conclusions of Section IV.

The paper is 2611. p. 0
Where the paper says it

To the best of our knowledge, the joint effect of MC on the radiated pattern, on the active mismatch presented to the PAs and on the Tx–Rx leakage that sets the sensing noise floor has not been addressed in ISAC beamforming, nor validated with full-wave simulation. This paper closes that gap with a hardware-grounded approach.

08331. EVERY sentence must end with a reference token. p. 2
Where the paper says it

, the ratio of mean reflected to mean incident power, and is linear in R; so is (7f). When rank(R) > 1, the instantaneous coefficient [STTx]n/xn varies with the data, so (1 + Γ¯ n)/(1 − Γ¯ n) is an equivalent VSWR that sets the mean reflected power seen by the PA, not a bound on the peak VSWR of every symbol; a per-symbol guarantee would require symbol-level constraints.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Beamforming design can be optimized to minimize sensing error by incorporating constraints on active reflection (VSWR limit) and Tx-Rx leakage budget through a semidefinite program (SDP). This allows for a leakage null in the beam domain, which reduces the root Cramer-Rao bound by 32 to 53 percent at 80 dB of self-interference cancellation.

  2. The system can achieve superior SINR performance compared to coupling-unaware designs by using a pattern-aware beamformer that solves (7b)–(7d) on the true embedded patterns. This design restores SINRs and the main beam, even when facing mutual coupling effects.

  3. The AI system can dynamically select the optimal leakage budget eta by performing a one-dimensional grid search over [ -45, -10 ] dB relative to PA power. This selection balances Fisher information delivered by the Tx subarray against the noise floor at the Rx subarray to minimize the upper bound on the Cramer-Rao bound.

  4. The system can be validated against different numerical solvers like FDTD and NEC-2, confirming that the leakage null is robust to the solver and feed model, ensuring hardware-grounded results are reliable across simulation platforms.

  5. The AI system can perform re-optimization directly on FDTD data by solving the SDP (7) using the true array model. This process selects a leakage budget and reaches a root Cramer-Rao bound that is 32 to 53 percent lower than benchmarks at 80 dB of SIC.

Abstract

Beamforming for integrated sensing and communication (ISAC) is usually designed on ideal array manifolds with a norm constraint on the transmit signal. In a compact monostatic transceiver this hides three antenna effects: distorted embedded patterns, beam-dependent active mismatch at the power amplifiers, and transmit-to-receive leakage that raises the radar noise floor. We build a multiport scattering model of a shared-aperture dipole array directly from method-of-moments simulations and use it to formulate a Cramer-Rao bound minimizing ISAC beamformer with multiuser SINR constraints, per-port active reflection constraints and a leakage budget, solved as a semidefinite program with a one-dimensional budget search. Full-wave evaluation shows that coupling-unaware designs miss their SINR targets by up to 6.2 dB and drive amplifiers to an equivalent VSWR above 3.3 at small spacings. For spacings from 0.3 to 0.5 wavelengths, the proposed design meets all targets with an equivalent VSWR below 2 and lowers the root Cramer-Rao bound by 32 to 53 percent for 80 dB of self-interference cancellation and by a factor of 3.4 to 5.6 for 70 dB. An independent finite-difference time-domain model of the final layout in openEMS confirms that the leakage null and the ranking of the designs are preserved.

Sources

Related papers