Uplink Enhancement for Low-Altitude UAVs via Active RISs Under Existing Cellular Infrastructure

arXiv:2611.07724 · eess.SP · Submitted 2026-11-05 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "Uplink Enhancement for Low-Altitude UAVs via Active RISs Under Existing Cellular Infrastructure".

Dev: Here's the gist of the paper. The paper introduces active reconfigurable intelligent surfaces (RISs) as a cost-effective solution to enhance uplink transmission for low-altitude Unmanned Aerial Vehicles (UAVs) in existing cellular infrastructure, specifically addressing coverage holes caused by downtilted base station antennas The key finding is that the impact of RIS noise is negligible under typical operating conditions, allowing for the derivation of an optimal reflection coefficient design to maximize the lower bound of the received signal-to-noise ratio.

Rosa: System Model and Coverage Hole Analysis The study considers a cellular network where a base station (BS) is equipped with a tri-sector antenna array configured with a downtilt angle of ϖB, which results in a vertical coverage gap called the coverage hole V.

Dev: This gap forms between altitudes r1 and r2 and is characterized by a tilt angle of ϖB + π/6, creating a frustum-shaped region.

Rosa: Active RISs are mounted on high-rise building rooftops with apertures facing skyward to construct reflection links for each BS sector.

Title and authors: Rosa: The paper is called "Uplink Enhancement for Low-Altitude UAVs via Active RISs Under Existing Cellular Infrastructure," and the authors are Weicong Chen, Chao-Kai Wen, Wankai Tang, Yiping Zuo, Xiao Li, and Shi Jin.

Dev: They’re researchers working on wireless systems who have done work in both cellular networks and optimizing these surfaces for things like aerial BSs or even mitigating interference when UAVs are connected.

Taro: So we're hearing from folks who understand the physics of these channels and how they interact with the physical environment, which is crucial because this whole thing relies on how well the reflection works in a real city setting.

Rosa: Yeah, they’ve done some work on things like sensing-assisted OFDM and learning optimal lattice vector quantizers for image compression, which gives them a good background in complex signal processing.

Dev: Their experience seems to bridge the gap between theoretical network planning and how those signals actually behave in tricky urban environments where you have these coverage holes.

The paper's summary: Rosa: The paper explains that they conduct a detailed noise analysis first, which is important because active RIS panels add their own noise into the system, and they figure out that this noise impact is negligible under typical operating conditions.

Dev: They derive an upper bound on the power ratio between the noise introduced by the active RIS and the inherent noise already present in the base station itself.

Taro: So, if that analysis shows it’s negligible, what does that mean for their design? Does it make designing those reflection coefficients simpler or easier?

Rosa: It actually simplifies things because they can move on to deriving an optimal reflection coefficient design to maximize the lower bound of the received signal-to-noise ratio.

Dev: They then look at how to get that best possible signal quality by decoupling the phase and amplitude of those reflection coefficients and using a sequential optimization approach.

Taro: So they’re optimizing both what direction the panel points and how strong it reflects, based on some channel information they can get from GPS data of the UAV.

The paper's improvements: Rosa: One improvement they suggest is that the optimal reflection phase design only needs statistical channel information calculated from GPS data of the UAV, which makes it manageable.

Dev: And for the amplitude, they design it based on a power constraint and maximizing the reflection amplitude to boost signal power while keeping things sensible.

Taro: The paper also points out something interesting about performance: numerical results show that under optimal reflection configurations, the SNR gain from active RIS is significantly greater than what you get from passive RIS panels.

Rosa: And they found that for enhancing uplink transmission, a larger RIS size seems to be better than just trying to achieve a higher reflection gain on a smaller surface.

Dev: They actually show an SNR enhancement of approximately twenty decibels with a maximum reflection amplitude of ten decibels compared to conventional passive RIS solutions <ref:2611.07724#pg2>.

Taro: What they also highlight is that when you fix the gain of the RIS array, a bigger size panel with a smaller reflection amplitude can actually give better uplink enhancement than a smaller panel with more reflection power.

Conclusion: Rosa: So to wrap up, this paper on "Uplink Enhancement for Low-Altitude UAVs via Active RISs Under Existing Cellular Infrastructure" shows that active RIS deployment can fill coverage holes by creating stable links without needing to modify the existing network infrastructure.

Dev: The key finding is that by doing a detailed noise analysis, they showed the noise impact of the active RIS is negligible, which lets them design an optimal reflection coefficient setup to maximize signal quality.

Taro: It suggests that for improving UAV uplink, we should focus on using larger RIS sizes rather than just trying to get huge reflection gains because of what the numerical results show about performance scaling.

Rosa: It’s a solid step forward because it moves beyond just showing coverage and actually provides a design strategy for maximizing the signal-to-noise ratio in this specific cellular context.

Dev: We should keep an eye on how real-world testing validates these twenty decibel gains, especially concerning latency and loop rates since that’s always a thing with active systems <ref:2611.07724#pg2>.

Taro: I agree, we need to see if those theoretical optimal designs hold up when the world misbehaves and the system has to recover gracefully.

Weicong Chen, Chao-Kai Wen, Wankai Tang, Yiping Zuo, Xiao Li, Shi Jin

National Mobile Communications Research Laboratory, Southeast University · Institute of Communications Engineering, National Sun Yat-sen University

eess.SP

Submitted: 2026-11-05

Updated: 2026-11-05

Comments: Minor Revision - IEEE Transactions on Communications

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 81/100

The gist: The paper introduces active reconfigurable intelligent surfaces (RISs) as a cost-effective solution to enhance uplink transmission for low-altitude Unmanned Aerial Vehicles (UAVs) in existing…

Key concepts

Active Reconfigurable Intelligent Surfaces (RIS)
RIS are smart surfaces mounted on buildings that can actively reflect incoming radio signals in specific directions. They adjust their reflection properties based on control signals from the base station to intelligently steer the signal towards a UAV, effectively creating a virtual line-of-sight path.
Coverage Hole
This is a gap in cellular network coverage where the signal strength drops significantly, often occurring between specific altitudes due to the downtilt of base station antennas. The paper focuses on using RIS to bridge this specific gap for UAV communication.
Noise Power Ratio Analysis
The authors analyzed the noise introduced by the active RIS compared to existing base station noise. They determined that under typical operating conditions, the noise power from the RIS is negligible. This crucial finding simplifies the design process, as it means they can focus purely on maximizing signal gain rather than worrying about excessive interference.
Optimal Reflection Design
This involves mathematically determining the best way to set each RIS element's reflection phase and amplitude. The design maximizes the received signal strength while respecting power constraints and ensuring that the beneficial signal boost outweighs any potential noise introduced by the active RIS components.

Terminology

Summary

The paper introduces active reconfigurable intelligent surfaces (RISs) as a cost-effective solution to enhance uplink transmission for low-altitude Unmanned Aerial Vehicles (UAVs) in existing cellular infrastructure, specifically addressing coverage holes caused by downtilted base station antennas The key finding is that the impact of RIS noise is negligible under typical operating conditions, allowing for the derivation of an optimal reflection coefficient design to maximize the lower bound of the received signal-to-noise ratio. p. 0

System Model and Coverage Hole Analysis

The study considers a cellular network where a base station (BS) is equipped with a tri-sector antenna array configured with a downtilt angle of ϖB, which results in a vertical coverage gap called the coverage hole V. This gap forms between altitudes r1 and r2 and is characterized by a tilt angle of ϖB + π/6, creating a frustum-shaped region. p. 2 Active RISs are mounted on high-rise building rooftops with apertures facing skyward to construct reflection links for each BS sector. p. 2 The BS transmits limited control signaling to the RISs over narrowband wireless control links to adjust the RIS reflection coefficients. p. 2

Noise Analysis and Noise Power Ratio

The authors conduct a detailed noise analysis to simplify the transmission design by deriving an upper bound on the power ratio between RIS-introduced noise and BS-inherent noise, revealing that the impact of RIS noise is negligible under typical operating conditions. The received signal at the k-th BS antenna sector is expressed as [50] yk,i = GkΓkgk,ix + zRk + zBk, where zB k ∼ CN (0, σ2 BINB) and zR k ∼ CN (0, σ2 RINR) are the noise terms at the k-th BS antenna sector and RISk. p. 3 The average post-combining noise power at the BS is defined as EwHzR + wHzB squared. p. 3

Optimal Reflection Design Derivation

Based on the analysis of the noise power ratio, a lower bound for the SNR of the JSMSC receiver is derived, and to maximize this SNR with reflection design of active RISs, they decouple the phase and amplitude of reflection coefficients and optimize them using a sequential optimization approach. The optimal reflection phase design is determined only by statistical CSI, which can be calculated from GPS data of the UAVi. p. 6 The optimal reflection amplitude is designed based on the power constraint and maximal reflection amplitude to maximize the received signal power. p. 6

Performance Evaluation and Conclusion

Numerical results validate that under optimal reflection configurations, the SNR gain achieved by active RISs is significantly greater than that of passive RISs, and a larger RIS size rather than a higher reflection gain is preferred for enhancing uplink transmission. The study demonstrates an SNR enhancement of approximately 20 dB with a maximum 10 dB reflection amplitude, substantially outperforming conventional passive RIS solutions. p. 9 The analysis shows that when the RIS array gain is fixed, a larger-sized RIS with a smaller reflection amplitude can achieve better uplink enhancement than a smaller-sized RIS with a larger reflection amplitude. p. 7

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Active RIS deployment in existing cellular infrastructure can fill coverage holes in low-altitude airspace by establishing stable virtual line-of-sight links between aerial devices and base stations without modifying existing network settings. This allows for enhanced uplink transmission for UAVs requiring high-definition video upload.

  2. A joint sector maximal signal combining (JS-MSC) scheme at the BS can be employed to harness spatial diversity through tri-sector BS cooperation, improving the UAV's SNR in coverage holes. This scheme is guided by closed-form expressions of average signal power and noise power derived from the analysis of noise introduced by active RISs.

  3. The system can be designed to maximize uplink transmission performance by decoupling the reflection vector as gamma k equals omega k times alpha k, and sequentially deriving closed-form solutions for the phase and amplitude vectors. This allows for optimal design of reflection coefficients based on statistical channel information.

  4. For UAV uplink enhancement, the optimal reflection amplitude is designed as alpha k n equals min (gamma max, r ER / (N R Ei rho 2 k + N R sigma 2 R)), which balances signal boosting against the constraint that active RIS noise remains negligible under typical operating conditions.

  5. The improved AI system can accurately determine the minimum BS-RIS distance dmin below which the amplification gain of active RIS fails to compensate for its introduced noise, guiding deployment strategies for maximizing SNR while ensuring noise remains less than a tolerable threshold.

Sources

Related papers