A Cost-Effective Submodule with Fault-Blocking Capability for Modular Multilevel Converters
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.
Rosa: We're looking at the paper: "A Cost-Effective Submodule with Fault-Blocking Capability for Modular Multilevel Converters".
Dev: Here's the gist of the paper. Modular multilevel converter (MMC) has become an attractive technology for high-power electronics applications thanks to its high energy efficiency, high power rating, high modularity, flexible scalability, and superior output waveform quality The proposed SM includes two variants, one employs only two fully-controlled switches The functionality of the proposed SM is validated by experiment, and the value of the SM is demonstrated through a test simulation for an high-voltage direct-current (HVDC) transmission system Problem Statement The half-bridge submodule (HBSM) cannot interrupt DC-side short-circuit currents Short-circuit fault on HVDC transmission lines may cause severe system failure and thus needs to be carefully dealt with To cut off fault current, circuit breakers can be employed on the AC- or DC-side of MMC However, they normally take several cycles to handle the fault, and this is not fast enough Proposed Submodule Topology The proposed SM is a passive circuit network with two variants as in Fig.
Rosa: 1 The circuit diagram of the first variant is shown in Fig.
Dev: 1(a) In the second variant, however, current can flow in both directions between the two ports Operation Modes The proposed SMs have three operation modes 1.
Rosa: Mode 1: Inserted State, where switch C1,k is closed and switch S2,k is open In this mode, the output voltage of the SM vk equals the sum of voltage vc1,k and vS 2.
Paper summary: Rosa: So we're looking at this paper, "A Cost-Effective Submodule with Fault-Blocking Capability for Modular Multilevel Converters." The main point here is that they propose two variants of submodules that can block DC short circuit currents without needing extra big components like circuit breakers.
Dev: Right, so the focus is on reducing the component count compared to what we currently use, especially when you're talking about those high-voltage direct current transmission systems where a fault can be really nasty. They're aiming at saving capital cost and operating loss because every extra switch adds hundreds or thousands of components to an entire converter if you look at a three-phase system.
Taro: From my side, I'm interested in how they handle the world misbehaving, specifically when the fault happens, because that's where the real stress is on the system and how gracefully it recovers when it does.
Rosa: Well, they introduce these two variants of submodules. One variant only uses two fully controlled switches, which is simpler than what we usually see in standard half-bridge submodules. They claim this topology achieves fault blocking capability with a reduced component count compared to existing options like the DCSM or MCSM.
Dev: That makes sense; looking at that comparison table they have, for instance, the MCSM uses four switches and six voltage levels, while their proposed variant might only use two fully controlled switches for one of its modes. The comparison shows how many voltage levels are needed versus the number of semiconductors in the current path when you're bypassed or inserted.
Taro: But I wonder about those specific operation modes they laid out. They talk about three states: inserted, bypassed, and blocked. How does switching between these states affect the fault current interruption?
Rosa: In Mode one, which is the inserted state, both switches are in a certain configuration where the output voltage is just the sum of those capacitor voltages plus a small switch voltage drop. Then they have Mode two where one switch is open and current flows from port two to port one, and the output voltage becomes that difference between the capacitor voltages.
Paper summary: Dev: And then there's Mode three, which is blocked state, where both switches are turned off. In that state, the output voltage just equals the voltage across one of those capacitors. That sounds like a way to isolate things when you need to stop a fault entirely without relying on external breakers that take too long.
Taro: So they’re suggesting that by controlling how these switches open and close, they can suppress the DC fault current directly within the converter itself. That’s a big idea for real-time protection.
Rosa: Exactly, and their experimental verification at low voltage showed this functionality works in a two level three phase MMC system. They tested both variants and plotted the results, showing that after the DC fault was blocked and current fell to zero, they could reset them back to Mode one or two around two point two seconds.
Dev: That recovery time is important for me, though. The paper mentions that during recovery, the DC link voltages are gradually rebuilt to their pre-fault level. They show that even when the system is recovering, the capacitor voltages and switch voltages stay within a maximum stress of one point five per unit.
Taro: So they're saying the switching logic handles both stopping the fault and then smoothly bringing everything back to normal operation without damaging anything during that transition phase? That sounds like a solid safety case.
Rosa: It does, but I have to be careful with the comparison they make on cost versus complexity. They argue that because their SM has fewer components than a DCSM with similar fault handling capability, it offers greater energy storage capacity while reducing building cost and operation complexity for MMCs overall.
Dev: That's the central argument for their title, "A Cost-Effective Submodule with Fault-Blocking Capability." It’s not just about adding protection; it’s about making the base building block cheaper and smaller to start with, which scales way better across a whole transmission system.
Taro: So for someone who only cares about the practical implementation, what's the main thing they flag as a limitation? Where does this approach stop working effectively?
Paper summary: Rosa: They do mention that the proposed SM variant one is used in converter A one operating as an inverter, and variant two is adopted for converter C one operating as rectification. It seems their verification was focused on these specific roles, though they show the general capability of both variants.
Dev: And from a controls engineer's view, I'd want to know more about the sorting algorithm they use to balance those capacitor voltages before operation starts. That initial setup is crucial for keeping everything stable before a fault even occurs.
Taro: The sorting algorithm determines which mode the SMs should be in based on the arm current direction, i k, and it also changes how capacitor voltages v c1 k react depending on whether that current is positive or negative. It sounds like they tie the control scheme directly into the operational modes.
Rosa: That sorting algorithm sets up the initial condition, but then it’s all about how quickly you can transition into Mode three to block that fault current. They show that when a short circuit fault occurs at two point zero five seconds, the DC link voltages fall and recover within one point zero per unit.
Dev: So they claim this capability without auxiliary protective equipment like circuit breakers, and they demonstrate it through simulation in SimPowerSystem in MATLAB/Simulink 2021a <ref:2611.07688#pg1>. The results show that the AC grid currents and DC currents rebuild successfully after the fault is cleared.
Taro: It’s interesting that they've shown how switch voltages across S1 and S2 stay within one point five per unit during the fault blocking stage, which suggests a controlled stress level on those switches. That's a concrete piece of data for real-world reliability.
Rosa: Yeah, it shows that their design keeps the voltage stress acceptable for all switches when they are doing their job of blocking that fault current. So, to wrap up this discussion on "A Cost-Effective Submodule with Fault-Blocking Capability for Modular Multilevel Converters," the paper presents a topology with two variants that can block DC fault current without external protection like circuit breakers.
Dev: It’s about making the base unit more component efficient while adding this crucial fault blocking feature, which is what really matters when you're dealing with high power applications in HVDC transmission.
Conclusion: Rosa: So we're wrapping up on this paper about "A Cost-Effective Submodule with Fault-Blocking Capability for Modular Multilevel Converters." Basically, they’ve shown these two new submodule designs that can handle DC short circuit faults without needing those bulky external circuit breakers.
Dev: Right, and the authors are focusing on making the module itself more component efficient while adding this crucial fault blocking feature. I mean, if you look at the component count in a whole modular multilevel converter, that really adds up fast.
Taro: It’s about reducing the overall building cost and operation complexity because they’re using fewer switches than what we usually see in standard half-bridge submodules. That's a big deal for making these systems practical.
Rosa: Exactly. They also found that even when the system is recovering from a fault, the capacitor voltages and switch voltages stay within one point five per unit, which means they’re keeping the stress on those components acceptable during that transition phase back to normal operation.
Dev: That recovery aspect is key for me. My concern is always about safety cases; how fast does it recover? They showed the DC link voltages rebuild quickly, increasing reversely within one point zero per unit after the fault clears.
Taro: So, they’re not just blocking the fault current and then leaving it there; they’re showing a smooth transition back to normal operation while keeping component stress managed. That shows how gracefully these submodules handle world misbehavior.
Rosa: It suggests that for high power applications like HVDC transmission, you can build more robust modules at a lower cost than before, which really helps with the economic side of things.
Dev: And this whole concept shifts the focus from just having protection to integrating it directly into the module design itself, which is where real-time control loops need to be smarter.
Taro: It opens up possibilities for designing these systems with inherent safety features built in, rather than adding expensive external hardware later on.
Shenzhen Technology University
eess.SY, cs.SY
Submitted: 2026-11-05
Updated: 2026-11-05
Comments: 11 pages, 22 figures
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 78/100
The gist: Modular multilevel converter (MMC) has become an attractive technology for high-power electronics applications thanks to its high energy efficiency, high power rating, high modularity…
Key concepts
- Modular Multilevel Converter (MMC)
- An MMC is a high-power electronics technology used for power conversion. It achieves high efficiency and quality output waveforms by using many submodules connected in series. These modules are modular, meaning they can be scaled up or down easily for different power requirements.
- Half-Bridge Submodule (HBSM)
- The HBSM is a standard component in MMCs that is typically used for interrupting DC-side short-circuit currents. The paper addresses the limitation of the HBSM, which cannot handle these faults quickly enough, leading to system failure risks.
- Operation Modes
- The submodule has three operational modes: Inserted State (Mode 1), Bypassed State (Mode 2), and Blocked State (Mode 3). These modes dictate how the switches are configured to manage power flow and fault current blocking, allowing the system to transition effectively during fault events.
Terminology
Summary
Modular multilevel converter (MMC) has become an attractive technology for high-power electronics applications thanks to its high energy efficiency, high power rating, high modularity, flexible scalability, and superior output waveform quality The proposed SM includes two variants, one employs only two fully-controlled switches The functionality of the proposed SM is validated by experiment, and the value of the SM is demonstrated through a test simulation for an high-voltage direct-current (HVDC) transmission system
Problem Statement
The half-bridge submodule (HBSM) cannot interrupt DC-side short-circuit currents Short-circuit fault on HVDC transmission lines may cause severe system failure and thus needs to be carefully dealt with To cut off fault current, circuit breakers can be employed on the AC- or DC-side of MMC However, they normally take several cycles to handle the fault, and this is not fast enough
Proposed Submodule Topology
The proposed SM is a passive circuit network with two variants as in Fig. 1 The circuit diagram of the first variant is shown in Fig. p. 1 Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. The circuit diagram of the first
variant is shown in Fig.Where the paper says it
Operation Modes
The proposed SMs have three operation modes
-
Mode 1: Inserted State, where switch C1,k is closed and switch S2,k is open In this mode, the output voltage of the SM vk equals the sum of voltage vc1,k and vS
-
Mode 2: Bypassed State, where switch C1,k is open and switch S2,k is closed When current flows from port 2 to port 1 (ik < 0), the output voltage vk equals the difference between the two capacitor voltages denoted as ∆vc = vc1,k − vc2,k
-
Mode 3: Blocked State, when both switches S1,k and S2,k are turned off In this stage, the output voltage of the SM vk is equal to vc1,k in this case
Operation Procedure
The operation procedure for the proposed SMs is designed and presented in this section The procedure repeats itself until the MMC is turned off
a) Initializing SMs: Before putting the SMs into operation, they need to be properly started up Above all, the capacitors in all SMs need to be charged to a preset voltage
b) Balancing capacitor voltages: The sorting algorithm is used to balance the capacitor voltages First, the SMs are sorted in ascending order within each arm according to the voltages of vc1
Experimental Verification
The functionality of the proposed SM topologies at low voltage are verified by experiment where the SMs are applied to a two-level three-phase MMC The experiment results using SM variant 1 and variant 2 are measured and plotted in Fig. 8 and Fig. 9 After the DC fault is blocked and the fault current has fallen to zeros, the SMs are reset back to Mode 1 or 2 at about t = 2. p. 7 Response of DC current: (a) non-permanent DC fault; (b)
permanent DC fault. After the DC fault is blocked and the fault current has
fallen to zeros, the SMs are reset back to Mode 1 or 2 at
about t = 2.Where the paper says it
Conclusion
A topology of SM with two variants and control scheme for MMC were proposed in this paper Both variants have the capability to block DC-fault current without auxiliary protective equipment such as circuit breaker Compared to a DCSM with the same component, both SMs can offer greater energy storage capacity These merits can help reduce the building cost and operation complexity for MMCs
Pruning redundant reasoning tokens
The exiting topologies with fault blocking capability require more switches than the HBSM The proposed SM topology contains three fullycontrolled switches, the second SM contains only two
How the training signal is built
The sorting algorithm is used to balance the capacitor voltages First, the SMs are sorted in ascending order within each arm according to the voltages of vc1 Then, depending on the direction of arm current ix, which is equal to ik, the operation mode of the SMs can be determined When ix > 0 and SMk is inserted, vc1,k increases whereas vc1,k decreases when ix < 0
Where the gains come from
Low power loss comparable to HBSM since there is only one switch conducting in Mode 1 and Mode 2 The proposed SMs operating in Mode 3 have the ability to suppress short-circuit fault currents Since the diodes in converter A1 are in reversed bias, and the switches S3 in converter C1 are turned off, therefore, the voltages across them are equal to the difference of both capacitor voltages in each SM All switch voltages are within 1.5 p.u., indicating an acceptable voltage stress for all switches during the fault-blocking The DC-link voltages at the DC-side of both converters fall quickly and increase reversely within 1 p. p. 8 As can be seen from the figures, all switch voltages
are within 1. , indicating an acceptable voltage stress
for all switches during the fault-blocking. At the DC-side of both converters, the currents decrease
quickly and increase reversely within 1 p. due to the
discharge of the capacitors to the fault, as shown in Fig. After reaching the maximum value within 1. in general, the capacitor voltages stay in constant as the
arm currents become zero in both converter, as shown in
Fig. After the fault has been detected,
both converters are set to blocked state by switching all
SMs to Mode 3. Consequently, the DC-currents of both
converters falls to zero, and so as the AC-currents of both
converters as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. 21 and Fig. Since
the diodes in converter A1 are in reversed bias, and the
switches S3 in converter C1 are turned off, therefore, the
voltages across them are equal to the difference of both
capacitor voltages in each SM, as shown in Fig. The proposed SM: (e) AC-grid currents; (f) arm currents;
(g) DC-link voltage; (h) DC-link current. Thereafter, the DC-link voltages and the DC-currents of
both converters are gradually rebuilt to the level before the
fault occurred, as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. 18(g)–
(h). Meanwhile, the capacitor voltages and the voltages
across all switches in all SMs return to the level as before
the fault occurrence during the recovery, as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. The test system is modeled and simulated
using SimPowerSystem in MATLAB/Simulink 2021a. After the system has reached steady state, a shortcircuit fault occurs at the DC-side of A1 at t = 0. 2104 Gcable (µS/km) 0. 0620
After that, the DC-link voltages at the DC-side of A1
and C1 fall quickly, as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. 17(g) and Fig. At the DC-side of both converters, the currents decrease
quickly and increase reversely within 1 p. At the DC-side of both converters, the currents decrease
quickly and increase reversely within 1 p. due to the
discharge of the capacitors to the fault, as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. The proposed SM: (e) AC-grid currents; (f) arm currents;
(g) DC-link voltage; (h) DC-link current. Thereafter, the DC-link voltages and the DC-currents of
both converters are gradually rebuilt to the level before the
fault occurred, as shown in Fig. 18(e), indicating
that both proposed SMs have the capability to block DC
fault currents. For comparison, the AC-currents and the
DC-currents of both converters increase significantly using
the HBSM, as shown in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. Finally, the conclusions are
drawn in Section VII. Topology of the Proposed Submodule
The proposed SM is a passive circuit network with two
variants as in Fig. flowing from the AC-side to the DC-side of the MMC. Nevertheless, the voltages across all components in SM
variant 2 remain within 1
2
vdc, as shown in Fig. 11(b)–
(d). For SM variant 2, the capacitor voltages are kept
around a constant value as shown in Fig.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
The proposed SM topology contains three fullycontrolled switches, the second SM contains only two The exiting topologies with fault blocking capability require more switches than the HBSM
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Improved AI system can implement modular multilevel converters (MMC) using two variants of submodules with fault-blocking capability, which can be compared to existing topologies that require more switches for similar functionality. This allows the system to achieve
Low power loss comparable to HBSM since there is only one switch conducting in Mode 1 and Mode 2.
-
The AI system can dynamically manage the operation of submodules based on arm current direction and capacitor voltage comparisons using a sorting algorithm. This enables the system to automatically balance capacitor voltages in most scenarios, as described by
the sorting algorithm is used to balance the capacitor voltages.
-
The AI system can implement a DC fault blocking mechanism by setting all submodules in an arm to Mode 3 when arm current exceeds a safety limit IF. This ensures that "all SMs in arm x will be set in Mode 3 until ix < IF or fault is cleared," effectively suppressing short-circuit fault currents.
-
The AI system can perform precise operation procedure sequencing for the MMC, including initial charging, voltage balancing, and contingency handling based on the direction of arm current. This involves setting
the first Nx SMs in Mode 1
when ix > 0 and "the last Nx SMs in Mode 1 while the rest are set in Mode 2 for ix < 0." -
The AI system can reduce building cost and control complexity by employing a proposed two-port submodule topology that requires only two switches, making it
comparable to the HBSM
in terms of component count while retaining fault-handling capability.
Abstract
Modular multilevel converter (MMC) has become an attractive technology for high-power electronics applications thanks to its high energy efficiency, high power rating, high modularity, flexible scalability, and superior output waveform quality. It has attracted considerable research attention, and numerous submodule (SM) variants have been developed for different objectives. Among them, the half-bridge SM (HBSM) is the most widely adopted thanks to its simplicity, but it cannot interrupt DC-side short-circuit currents. Various SM topologies with fault-blocking capability have been proposed. These SM topologies contain additional switches and passive components compared to the HBSM, leading to higher capital and operating costs. Aiming at these issue, an SM topology capable to block DC-side fault-currents with a reduced component count is proposed in this paper. The proposed SM includes two variants, one employs only two fully-controlled switches. An operation and control scheme for the proposed SM are also developed and presented in the paper. The functionality of the proposed SM is validated by experiment, and the value of the SM is demonstrated through a test simulation for an high-voltage direct-current (HVDC) transmission system.
Related papers
- Industrial Load Modeling and Optimization for Market-Based Interaction with Power Systems
- Exact and Approximate Convex Reformulation of Linear Stochastic Optimal Control with Chance Constraints
- Certified Set Convergence for Piecewise Affine Systems
- Symbolic Control for Stochastic Systems via Finite Parity Games
- Multiobjective optimization-based design and dispatch of islanded, hybrid microgrids for remote, off-grid communities in sub-Saharan Africa
- Physiology-informed layered sensing for intelligent human-exoskeleton interaction