Improper Signaling for Clutter-Limited Angle Estimation in ISAC

arXiv:2611.06805 · eess.SP · Submitted 2026-11-04 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "Improper Signaling for Clutter-Limited Angle Estimation in ISAC".

Dev: Here's the gist of the paper. Integrated sensing and communication (ISAC) transmit designs typically optimize the transmit covariance under proper signaling, leaving the potential sensing benefits of pseudocovariance unexplored<ref:2611.06805#pg2>.

Rosa: This paper investigates the conditions under which transmit pseudo-covariance can influence the angle Cramer–Rao bound (CRB) of a deterministic target in the presence of clutter<ref:2611.06805#pg4>.

Dev: Investigating Transmit Pseudo-Covariance The study explores how transmit pseudo-covariance can affect the angle CRB by shaping the pseudo-covariance of the signal-dependent clutter observed by a widely linear receiver<ref:2611.06805#pg4>.

Rosa: For a single clutter patch, it is shown that the pseudo-covariance affects the angle CRB if and only if the clutter is illuminated, non-circular, and overlaps the angle-informative component of the target response<ref:2611.06805#pg4>.

Paper summary: Rosa: So we're looking at this paper, "Improper Signaling for Clutter-Limited Angle Estimation in ISAC". It basically says that when you design your transmit signal covariance, you usually just optimize it for proper signaling, but you're missing out on potential benefits from using something called pseudo-covariance <ref:2611.06805#pg2>.

Dev: Right. The core idea here is to see if this transmit pseudo-covariance can actually influence the angle Cramer–Rao bound, or CRB, when there's clutter in the signal. It investigates the conditions under which this transmit pseudo-covariance can affect that angle CRB <ref:2611.06805#pg4>.

Taro: So it’s not just about having a better signal; it’s about how the way we transmit—the pseudo-covariance—changes what we can actually measure about the target, especially when there's noise or clutter around <ref:2611.06805#pg4>.

Rosa: Exactly. They explore how this transmit pseudo-covariance shapes the pseudo-covariance of the signal-dependent clutter that a receiver with a wide linear response sees <ref:2611.06805#pg4>. The condition they find is pretty specific: it only matters if that clutter is illuminated, non-circular, and overlapping the part of the target's response that gives you angle information <ref:2611.06805#pg4>.

Dev: That’s a big qualification. It tells us angular separation by itself isn't enough to know if this transmit impropriety actually helps performance <ref:2611.06805#pg4>. But they go on to derive an optimal design for the incident field pseudo-variance that minimizes the angle CRB across all possible transmit pseudo-covariances <ref:2611.06805#pg4>.

Taro: What does that optimal design actually look like in practice? Does it make things simpler or more complex?

Rosa: Well, under fully noncircular clutter scattering, the paper says this optimal design completely eliminates the penalty that clutter causes to the CRB <ref:2611.06805#pg4>. The best way to do this is to be maximally improper along the direction of that clutter itself <ref:2611.06805#pg4>.

Dev: So, we're designing the signal not just to be good for communication, but specifically to fight the clutter penalty by being improper in a particular way dictated by where the clutter is coming from and how non-circular it is <ref:2611.06805#pg4>. That sounds like a tight constraint on our transmit covariance design.

Taro: If we look at the numerical results, they show some pretty big gains in a three-twenty antenna system <ref:2611.06805#pg5>. They found CRB reductions of up to ninety-nine percent when there's complete overlap with the target and a thirty percent reduction under partial overlap <ref:2611.06805#pg5>.

Paper summary: Rosa: That ninety-nine percent is significant compared to what we get when we use proper sensing design <ref:2611.06805#pg5>. They gave us an expression for the optimal relative CRB reduction, which is rho c chi gamma one plus gamma one minus chi minus rho c gamma <ref:2611.06805#pg6>.

Dev: And they noted that in the edge case of rectilinear clutter, where rho c equals one, this whole clutter penalty gets completely eliminated under the single-patch simplification <ref:2611.06805#pg6>. So if our environment is very simple and structured, this technique looks very effective at removing that noise floor imposed by the clutter <ref:2611.06805#pg4>.

Taro: I wonder how robust these gains are when we move away from those simple cases. What happens when the clutter isn't perfectly noncircular?

Rosa: The paper sets up a condition for sensitivity: the angle CRB changes over time, or over the set of receiver locations, if and only if there is a non-zero value for sigma squared c w, rho c, and zeta not equal to zero <ref:2611.06805#pg5>.

Dev: That’s a three-way condition. It means that the projected clutter only occupies one direction when that direction is zero, which effectively makes the clutter disappear from that specific measurement subspace and keeps the angle CRB constant there <ref:2611.06805#pg5>. But if all three of those things are true, you get two different feasible transmit pseudo-covariances yielding two different angle CRBs <ref:2611.06805#pg5>.

Taro: So, we need a non-zero real part for the noise structure, a non-zero pseudo-covariance factor, and some geometric mismatch to actually see this effect on the bound <ref:2611.06805#pg5>. That gives us something concrete to test in our simulations when things get messy.

Rosa: And they find that the optimal phase for this design is a pi, and the resulting transmission vector expression is maximized when a certain variable, denoted as z, has a magnitude of one <ref:2611.06805#pg6>. This leads to an optimal pseudo-covariance expression involving we star minus the term two arg alpha zeta minus psi c <ref:2611.06805#pg6>.

Dev: And what’s the practical gain from this optimal design? They show that this specific design achieves up to about seven decibels lower penalty compared to the proper sensing case, even in the same separation window <ref:2611.06805#pg5>. That's a measurable improvement for our system performance metrics.

Paper summary: Taro: So, if I’m trying to decide whether to implement this, I need to know what the trade-off is. It sounds like we have to balance the complexity of designing this optimal pseudo-covariance against those potential seven decibels of gain <ref:2611.06805#pg5>.

Rosa: Right. The authors summarize that they’ve established necessary and sufficient conditions for when the angle CRB can be affected by this transmit pseudo-covariance <ref:2611.06805#pg4>. They say the projected overlap, the clutter strength, and how non-circular it is determine exactly how much reduction you can actually achieve <ref:2611.06805#pg4>.

Dev: So what this means for us in the lab or on deployment is that we don't just stick to optimizing the transmit covariance for clean signals anymore <ref:2611.06805#pg2>. We can deliberately design an "improper" transmission pattern if we know the clutter characteristics are right, and it might save us a lot of estimation error compared to just using proper signaling <ref:2611.06805#pg4>.

Taro: I think the future work they mention is important. They plan to develop adequate improper conditions for multi-clutter patch scenarios <ref:2611.06805#pg5>. That’s a bigger challenge because real environments aren't just one simple clutter patch; they are complex <ref:2611.06805#pg4>.

Rosa: That makes sense. Moving from single patches to multiple patches is where the real world gets tricky, and the authors are looking at how that scales <ref:2611.06805#pg5>. They also plan to look at the CRB-rate tradeoff issue, which is another layer of complexity for integrated systems <ref:2611.06805#pg5>.

Dev: It seems like this paper gives us a clear set of checks—the three conditions—to determine if we even have a chance to improve the angle CRB with transmit pseudo-covariance <ref:2611.06805#pg4>. It moves it from just a theoretical curiosity to something we can actually engineer for specific clutter environments <ref:2611.06805#pg4>.

Taro: So, the main thing is that you need the right geometry and clutter type to get that improvement, otherwise you're just adding complexity without gain <ref:2611.06805#pg4>.

Rosa: Precisely. It’s not a magic fix; it’s a conditional improvement based on the physics of how the clutter is shaped and where it sits relative to our target <ref:2611.06805#pg4>. That's what we learned from this work on "Improper Signaling for Clutter-Limited Angle Estimation in ISAC".

Conclusion: Rosa: So, we're wrapping up this talk on "Improper Signaling for Clutter-Limited Angle Estimation in ISAC". Basically, this paper is about how you can intentionally mess with your transmit signal design to actually get better angle estimates when there's clutter around.

Dev: Right. The authors are looking at the conditions where this transmit pseudo-covariance can actually help lower the angle Cramer–Rao bound, or CRB, which is basically how accurate your direction finding is supposed to be.

Taro: It boils down to specific geometric setups with the clutter—things like whether that clutter patch is illuminated and if it’s non-circular—because if those conditions aren't met, messing with the signal doesn't actually improve performance.

Rosa: That’s the key takeaway. You need a certain geometry for this trick to work at all <ref:2611.06805#pg4>. But when you have that setup, they show you how to pick the best transmit pattern—the optimal one—to minimize that error bound.

Dev: And the results are pretty strong on the numbers. They’re showing CRB reductions of up to ninety-nine percent in some three twenty antenna system scenarios when there's complete overlap with your target, and thirty percent under partial overlap <ref:2611.06805#pg5>.

Taro: That kind of reduction is huge for a sensor system. It means you could get much better direction finding than you would if you just used standard proper sensing designs <ref:2611.06805#pg4>.

Rosa: Exactly. The implication is that we're not locked into just designing the transmit covariance to be perfectly "proper" for communication anymore; we can design it to be intentionally improper in a specific, calculated way <ref:2611.06805#pg2>.

Dev: It’s about finding that sweet spot where you balance the complexity of designing this optimal pseudo-covariance against those potential seven decibels of error reduction <ref:2611.06805#pg5>.

Taro: And the authors did flag a limitation, though. They show us exactly what conditions—the non-zero noise structure, the non-zero pseudo-covariance factor, and that specific geometric mismatch—are necessary for this whole effect to even happen <ref:2611.06805#pg5>.

Rosa: So while it’s a powerful tool for certain environments, you can’t just throw this trick at every single radar scenario; it has to fit the clutter and the geometry perfectly.

Dev: That's right. The real world is messy, so this paper gives us those specific checks to see if we even have a chance to improve our angle estimation with transmit impropriety <ref:2611.06805#pg4>.

Taro: Next time, we'll look at how these conditions change when you move from just one simple clutter patch to a whole complex multi-clutter environment <ref:2611.06805#pg5>.

Victor Augusto Del Monego, Polianna Basso, Murilo Capponi, Bruno S. Chang, Yahia Medjahdi, Giuseppe Thadeu Freitas de Abreu, Didier Le Ruyet

CPGEI/Electronics Department, Federal University of Technology - Parana · IMT Nord Europe, Institut Mines Telecommunication, Center for Digital Systems · School of Computer Science and Engineering, Constructor University · CEDRIC/Conservatoire National des Arts et Metiers - Paris

eess.SP

Submitted: 2026-11-04

Updated: 2026-11-04

Comments: 6 pages, 4 figures, submitted to the IEEE International Conference on Communications (ICC), 2027

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 79/100

The gist: Integrated sensing and communication (ISAC) transmit designs typically optimize the transmit covariance under proper signaling…

Key concepts

Transmit Pseudo-Covariance
This refers to the intentional design choices made in the signal transmission (the transmit covariance matrix) that are not optimized for standard communication. The paper explores how these 'improper' choices can shape the observed clutter characteristics, which in turn affects how accurately a receiver can estimate the target's angle.
Angle Cramer–Rao Bound (CRB)
The CRB sets the theoretical minimum variance achievable when estimating an unknown parameter, such as a target's angle. The study examines whether manipulating the transmit signal's pseudo-covariance can change this minimum bound, potentially leading to better angular estimation performance than standard designs.
Clutter Illumination and Non-circularity
For transmit pseudo-covariance to affect the CRB, the clutter must be illuminated by the signal and possess non-circular characteristics. This means the clutter's scattering pattern is not uniform in all directions, and it must overlap with where the target's response is most informative for this effect to occur.

Terminology

Summary

Integrated sensing and communication (ISAC) transmit designs typically optimize the transmit covariance under proper signaling, leaving the potential sensing benefits of pseudocovariance unexplored<ref:2611. p. 006805#pg2>. This paper investigates the conditions under which transmit pseudo-covariance can influence the angle Cramer–Rao bound (CRB) of a deterministic target in the presence of clutter<ref:2611. p. 006805#pg4>.

Investigating Transmit Pseudo-Covariance

The study explores how transmit pseudo-covariance can affect the angle CRB by shaping the pseudo-covariance of the signal-dependent clutter observed by a widely linear receiver<ref:2611.06805#pg4>. For a single clutter patch, it is shown that the pseudo-covariance affects the angle CRB if and only if the clutter is illuminated, non-circular, and overlaps the angle-informative component of the target response<ref:2611. p. 006805#pg4>. This characterization demonstrates that angular separation alone does not determine whether transmit impropriety can improve sensing performance<ref:2611. p. 006805#pg4>.

Deriving Optimal Design Conditions

The paper derives a closed-form optimal incidentfield pseudo-variance that minimizes the angle CRB over the set of feasible transmit pseudo-covariances<ref:2611.06805#pg4>. Under fully noncircular clutter scattering, the optimal design eliminates the clutter-induced CRB penalty<ref:2611. p. 006805#pg4>. The optimal design is maximally improper along the clutter direction, with a phase set by the clutter non-circularity and the target–clutter geometry<ref:2611. p. 106805#pg4>.

Quantifying Sensing Performance Gains

Numerical results for a 32-antenna ISAC system show CRB reductions of up to 99% relative to proper sensing under complete overlap and 30% under partial overlap<ref:2611.06805#pg5>. The optimal relative CRB reduction DCRB is given by the expression ρcχγ(1 + γ)[1 + (1 − χ)(1 − ρc)γ]<ref:2611. p. 406805#pg6>. For the edge case of rectilinear clutter, rho c = 1, we⋆ completely eliminates the clutter-induced CRB penalty under the single-patch simplification<ref:2611. p. 406805#pg6>.

Determining Sensitivity Criteria

The angle CRB is nonconstant over C(Rx) if and only if σ2cw > 0, ρc > 0, ζ ≠ 0<ref:2611.06805#pg5>. This condition arises because the projected clutter occupies only the direction b when b = 0, the clutter vanishes from this subspace and the angle CRB is independent of Cx<ref:2611. p. 306805#pg5>. Conversely, if all three conditions hold, two feasible transmit pseudo-covariances yield different angle CRBs<ref:2611. p. 306805#pg5>.

Optimal Pseudo-Covariance Selection

The optimal phase satisfies δ = π, and the resulting expression h = [1 + γ − γρcz]−1 is maximized at z = 1<ref:2611.06805#pg6>. The optimal pseudo-covariance is therefore given by we⋆ = -wej[2 arg(αζ)−ψc]<ref:2611. p. 406805#pg6>. This optimal design achieves up to approximately 7 dB lower penalty than the proper case in the same separation window<ref:2611. p. 406805#pg5>.

Conclusion and Future Work

The work establishes necessary and sufficient conditions under which the angle CRB of an ISAC system can be affected by the transmit pseudo-covariance<ref:2611.06805#pg4>. Future work includes further development of adequate improper conditions in a multi-clutter patch scenario, as well as the expansion of this concept to the CRB-rate tradeoff issue<ref:2611. p. 506805#pg5>. The results illustrate how the three conditions established in Section III determine whether impropriety can affect the angle CRB, while the projected overlap, clutter strength, and non-circularity determine the magnitude of the achievable reduction. p. 5 <ref:2611.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improve transmit design by exploiting transmit pseudo-covariance to reduce angle Cramer–Rao bound (CRB) penalty in Integrated Sensing and Communication (ISAC). This allows the system to achieve CRB reductions of up to 99% relative to proper sensing under complete overlap or up to approximately 7 dB lower clutterinduced CRB penalty across target–clutter separations.

  2. Implement an optimal transmit pseudo-covariance design based on the projected target–clutter geometry. The paper derives a closed-form optimal incident field pseudo-variance that eliminates the clutter-induced CRB penalty under fully noncircular clutter scattering, specifically by choosing the optimal design is maximally improper along the clutter direction.

  3. Develop an adaptive sensing strategy where the system dynamically adjusts its transmit pseudo-covariance based on real-time channel and target information. This adaptation is governed by maximizing a term in the CRB expression, such as finding an optimal phase set by the clutter non-circularity and the target–clutter geometry to achieve CRB(theta) = ffree in cases of rectilinear clutter.

Related papers