Joint Discrete Pinching-Antenna Activation and Beamforming Design for Efficient PASS-ISAC

arXiv:2610.03371 · eess.SP · Submitted 2026-10-02 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "Joint Discrete Pinching-Antenna Activation and Beamforming Design for Efficient PASS-ISAC".

Dev: Here's the gist of the paper. Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement, which may be impractical with preinstalled hardware<ref:2610.03371#pg2>.

Rosa: We investigate a discrete-activation multiwaveguide PASS-ISAC system that selects sparse transmit and receive pinching antennas (TPAs/RPAs) from predefined locations<ref:2610.03371#pg3>.

Dev: System Architecture and Model The system consists of a dual-function central processing unit that communicates with a single-antenna user while simultaneously sensing a point target<ref:2610.03371#pg3>.

Rosa: The physical deployment involves M transmit and N receive dielectric waveguides, each containing KT TPAs (KR RPAs) pre-mounted at discrete candidate locations<ref:2610.03371#pg3>.

Paper summary: Rosa: So what they claim is they devise a way to solve this communication-rate maximization problem by jointly optimizing both the waveguide beamforming and whether or not you activate those specific TPAs and RPAs. Dev They propose a low-complexity algorithm called JDPABO which uses alternating optimization, successive convex approximation, and reweighted one norm minimization to handle that tricky non-convex problem. Rosa The paper sets up this system with a dual function central processing unit that talks to one antenna for communication and senses a point target at the same time. Dev They describe the setup where you have M transmit and N receive dielectric waveguides, each holding KT TPAs or KR RPAs pre-mounted at specific candidate locations. Rosa The whole point is that instead of using everything all the time, you only turn on a sparse subset of those antennas to save complexity and power.

Taro: I wonder how that sparsity actually translates into something useful when the environment isn't perfect? If you're only activating a few points, does it compromise the sensing performance too much? Rosa That’s exactly what they test. They show simulation results where JDPABO approaches performance levels you’d see if you used continuous placement, especially when the sensing signal to noise ratio is low. Dev They found that when the sensing requirement is low, the user-centric scheme performs quite well by focusing on strengthening that communication link first.

Rosa: But as you increase that sensing requirement, like needing a stronger target illumination, the target-centric scheme starts getting closer to their proposed JDPABO approach. Dev That makes sense because activating those TPAs close to the actual target improves how well you illuminate it, which helps meet that sensing constraint.

Conclusion: Rosa: So looking at the whole paper, "Joint Discrete Pinching-Antenna Activation and Beamforming Design for Efficient PASS-ISAC," what they’ve done is put together a system that uses preinstalled antennas in a smart, sparse way for both communication and sensing. Dev They developed the JDPABO algorithm to link those two things—the beamforming weights on the waveguides and which specific TPAs or RPAs are turned on. Rosa The implication is that you can get better performance than if you just used a fixed activation scheme, which is what they showed performs worst because it can’t adapt to where the user and target are. Dev It shows how combining beamforming optimization with discrete antenna selection lets you handle those constraints of power, sparsity, and sensing SNR together in a single framework.

Taro: It seems like the main contribution is showing that this joint optimization approach actually leads to better results than just optimizing communication or just optimizing sensing separately. Rosa Right. And they did show that when the target-centric scheme is used, activating TPAs near the target really helps with illumination, which makes satisfying that sensing requirement much easier for the system.

Dev: The paper flags a limitation, though; it states that this discrete activation approach can struggle when you need a very high level of adaptation to changing geometry or if you have extremely strict real-time constraints on switching those antenna activations. Rosa So, while JDPABO is better than fixed activation and gets close to continuous performance at low sensing requirements, the authors admit it’s not perfect for every single scenario.

Taro: That's fair. It’s a discrete system by definition, so there are always limits on how much you can adapt the antenna pattern in real time compared to a perfectly continuous one. Dev So that's what they were trying to address: finding the right balance between complexity and performance when you only have those preinstalled hardware locations available.

School of Electrical Engineering and Computer Science, Ohio University · Faculty of Engineering and Applied Science, Memorial University

eess.SP

Submitted: 2026-10-02

Updated: 2026-11-11

Comments: 6 pages, 5 figures, accepted for publication in the proceeding of the IEEE CCNC-2027

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 71/100

The gist: Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement…

Key concepts

PASS-ISAC
This refers to a system that integrates sensing (detecting targets) and communication (sending data) using pinching antennas. The goal is to use these flexible antenna points efficiently for both tasks simultaneously in a single setup.
Discrete Pinching Antennas (TPAs/RPAs)
These are the specific antenna elements used in the system. Instead of having continuous placement, this system selects only a sparse set of pre-installed antennas from fixed candidate locations to perform transmission or reception.
JDPABO Algorithm
This is a low-complexity optimization method that jointly designs two things: the transmit beamforming weights and which specific TPAs/RPAs should be activated. It uses an alternating optimization approach to find the best combination for maximizing communication rate under various constraints.

Terminology

Summary

Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement, which may be impractical with preinstalled hardware<ref:2610. p. 0

Where the paper says it

edu, odobre@mun. ca Abstract—Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement, which may be impractical with preinstalled hardware.

03371#pg2>. We investigate a discrete-activation multiwaveguide PASS-ISAC system that selects sparse transmit and receive pinching antennas (TPAs/RPAs) from predefined locations<ref:2610. p. 0
Where the paper says it

ca Abstract—Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement, which may be impractical with preinstalled hardware. We investigate a discrete-activation multiwaveguide PASS-ISAC system that selects sparse transmit and receive pinching antennas (TPAs/RPAs) from predefined locations.

03371#pg3>.

System Architecture and Model

The system consists of a dual-function central processing unit that communicates with a single-antenna user while simultaneously sensing a point target<ref:2610.03371#pg3>. The physical deployment involves M transmit and N receive dielectric waveguides, each containing KT TPAs (KR RPAs) pre-mounted at discrete candidate locations<ref:2610. p. 1

Where the paper says it

,N}, respectively. Each transmit (receive) waveguide contains KT TPAs (KR RPAs) pre-mounted at discrete candidate locations, indexed by KT ={1,.

03371#pg3>. The 3D coordinates of the kth TPA on the mth transmit waveguide are given by ψT,m,k = [xT,k, yT,m, H]<ref:2610. p. 1
Where the paper says it

Weadoptathree-dimensional(3D)Cartesiancoordinatesystem,whereinthewaveguidesaredeployedatheight H over a rectangular serving area of lengthLand width W in the x-y plane, with the midpoint of each waveguide centered at x= 0 and its y-coordinate fixed by the deployment layout. Accordingly, the 3D coordinates of the kth TPA on the mth transmit waveguide and the lth RPA on the nth receive waveguide are given by ψT,m,k = [xT,k, yT,m, H] T and ψR,n,l =[xR,l,yR,n,H] T , respectively.

03371#pg3>. The channel model employs a spherical-wave channel model<ref:2610. p. 1
Where the paper says it

The user and target are located on the ground at ψu =[xu,yu,0]T and ψt =[xt,yt,0]T , respectively. Channel Model Duetonear-fieldpropagation,weadoptthespherical-wave channel model [21].

03371#pg3>.

Optimization Formulation

The optimization problem is formulated as maximizing the communication rate subject to transmit power, sparsity, and sensing SNR constraints<ref:2610.03371#pg5>. The objective is to maximize log2(1+γu) subject to constraints on normalized transmit power, sparsity of activations, and a minimum required radar SNR<ref:2610. p. 2

Where the paper says it

(13g) where γs,min denotes the minimum required radar SNR. Constraint (13b) limits the total normalized transmit power across all transmit waveguides to unity.

03371#pg5>.

Proposed Solution Methodology

The proposed solution employs a low-complexity joint discrete pinching-antenna activation and beamforming optimization (JDPABO) algorithm based on alternating optimization<ref:2610.03371#pg3>. This approach breaks the problem into two subproblems: first, optimizing the transmit beamforming vector w for fixed antenna patterns, and second, optimizing the TPA and RPA activation variables a and b for a fixed beamforming vector w<ref:2610. p. 2

Where the paper says it

This approach breaks down the initial problem into two distinct subproblems. First, the transmit beamforming vector w is optimized for fixed TPA and RPA activation patterns.

03371#pg5>.

Algorithm Details

The JDPABO algorithm iteratively solves these subproblems using successive convex approximation (SCA)<ref:2610.03371#pg5>. In Subproblem 1, the communication objective is relaxed using slack variables ρu and ρt, and the constraints are approximated by affine constraints via first-order Taylor expansions<ref:2610. p. 3

Where the paper says it

At the jth SCA iteration, the convex quadratic terms are replaced by their first-order Taylor lower bounds around (p (j) u ,q (j) u ) and (p (j) t ,q (j) t ), respectively. Accordingly, (15) and (16b) are approximated by the following affine constraints: p (j) u 2 +2p (j) u (pu−p (j) u )+q (j) u 2 +2q (j) u (qu−q (j) u )≥ ρu γu , (18a) p (j) t 2 +2p (j) t (pt−p (j) t )+q (j) t 2 +2q (j) t (qt−q (j) t )≥ ρt γr .

03371#pg6>. In Subproblem 2, similar SCA techniques are used to approximate non-convex terms involving sensing SNR and bilinear products of activation variables<ref:2610. p. 0
Where the paper says it

Simulations show that JDPABO approaches continuous-placement performance at low sensing SNR requirements and outperforms fixed activation schemes with sparse PA activation. Index Terms—Pinching-antenna (PA), integrated sensing and communication (ISAC), antenna selection, successive convex approximation (SCA) I.

03371#pg6>. The final problem is relaxed using reweighted l1 minimization to handle the binary constraints on TPA/RPA activations<ref:2610. p. 4
Where the paper says it

To obtain a tractable formulation, we employ reweighted ℓ1 minimization [23], [24], relax the binary constraints in (13f) and (13g), and introduce sparsity-promoting penalties into the objective. Accordingly,atthejthSCAiteration,problem(20)isrelaxed to obtain the TPA and RPA activation variables as follows: max a,b,ρu, ρt,ζt log2 (1+ρu)−µT X M m=1 X KT k=1 λ (j) m,kam,k−µR X N n=1 X KR l=1 λ (j) n,lbn,l (28a) s.

03371#pg6>.

Performance Evaluation

Simulation results demonstrate that JDPABO approaches continuous-placement performance at low sensing SNR requirements<ref:2610.03371#pg7>. The algorithm consistently achieves the highest rate by jointly optimizing transmit beamforming and TPA/RPA activation based on the user and sensing channels<ref:2610. p. 5

Where the paper says it

4 compares the communication rate of JDPABO with the baseline schemes as the transmit power increases. JDPABO consistently achieves the highest rate by jointly optimizingtransmitbeamformingandTPA/RPAactivation based on the user and sensing channels.

03371#pg6>. The target-centric scheme performs closest to JDPABO, as activating TPAs near the target improves illumination and facilitates satisfaction of the sensing SNR constraint<ref:2610. p. 5
Where the paper says it

The target-centric scheme performs closest to JDPABO, as activating TPAs nearthetargetimprovesilluminationandfacilitatessatisfaction of the sensing SNR constraint. The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination.

p. 5
Where the paper says it

The target-centric scheme performs closest to JDPABO, as activating TPAs nearthetargetimprovesilluminationandfacilitatessatisfaction of the sensing SNR constraint. The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination.

03371#pg7>. The fixed activation scheme performs worst due to its inability to adapt the antenna activation to the user-target geometry<ref:2610. p. 5
Where the paper says it

The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination. The fixed activation scheme performs worst due to its inability to adapt the antenna activation to the user-target geometry.

p. 5
Where the paper says it

The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination. The fixed activation scheme performs worst due to its inability to adapt the antenna activation to the user-target geometry.

03371#pg7>.

Conclusion

In this paper, we investigated a discrete-activation multiwaveguide PASS-ISAC architecture, where TPAs/RPAs are selected from pre-installed candidate locations<ref:2610.03371#pg6>. We developed a low-complexity JDPABO algorithm to jointly optimize the waveguide beamforming weights and sparse TPA/RPA activation patterns for communication-rate maximization under transmit power, antenna-selection, and sensing SNR constraints<ref:2610. p. 5

Where the paper says it

Conclusion In this paper, we investigated a discrete-activation multiwaveguide PASS-ISAC architecture, where TPAs/RPAs are selected from pre-installed candidate locations. We developed a low-complexity JDPABO algorithm to jointly optimize the waveguide beamforming weights and sparse TPA/RPA activation patterns for communication-rate maximizationundertransmit-power,antenna-selection,and sensing SNR constraints.

03371#pg6>. Simulation results demonstrated that JDPABO outperforms fixed activation schemes and approached the continuous-placement benchmark at low sensing SNR requirements<ref:2610. p. 5
Where the paper says it

We developed a low-complexity JDPABO algorithm to jointly optimize the waveguide beamforming weights and sparse TPA/RPA activation patterns for communication-rate maximizationundertransmit-power,antenna-selection,and sensing SNR constraints. Simulation results demonstrated that JDPABO outperforms fixed activation schemes and approached the continuous-placement benchmark at low sensing SNR requirements.

03371#pg7>.

REFERENCES

arXiv:2610.03371v1 [eess. p. 0

Where the paper says it

(·) T and (·) H arXiv:2610. 03371v1 [eess.

SP] 2 Oct 2026

--- Page 5 ---

Fig. 5 shows the communication rate versus the sensing SNR requirement under random user and target locations<ref:2610. p. 5

Where the paper says it

The fixed activation scheme performs worst due to its inability to adapt the antenna activation to the user-target geometry. 5 shows the communication rate versus the sensing SNR requirement for random user and target locations.

03371#pg7>. As γs,min increases, the rate decreases for all schemes, highlighting the communication-sensing trade-off<ref:2610. p. 5
Where the paper says it

5 shows the communication rate versus the sensing SNR requirement for random user and target locations. As γs,min increases, the rate decreases for all schemes, highlighting the communication-sensing trade-off.

03371#pg7>. At low sensing requirements, the user-centric scheme remains competitive by strengthening the communication link<ref:2610. p. 5
Where the paper says it

As γs,min increases, the rate decreases for all schemes, highlighting the communication-sensing trade-off. At low sensing requirements, the user-centric scheme remains competitive by strengthening the communication link.

03371#pg7>. As the sensing requirement increases, the target-centric scheme approaches the proposed scheme by providing stronger target illumination<ref:2610. p. 5
Where the paper says it

At low sensing requirements, the user-centric scheme remains competitive by strengthening the communication link. As the sensing requirement increases, the target-centric scheme approaches the proposed scheme by providing stronger target illumination.

03371#pg7>. In contrast, the midpoint-based and fixed schemes exhibit larger performance gaps because their activation patterns are less adaptive to the user-target geometry<ref:2610. p. 5
Where the paper says it

As the sensing requirement increases, the target-centric scheme approaches the proposed scheme by providing stronger target illumination. In contrast, the midpoint-based and fixed schemes exhibit larger performance gaps because their activation patterns are less adaptive to the user-target geometry.

03371#pg7>.

--- Page 6 ---

Fig. 4 compares the communication rate of JDPABO with the baseline schemes as the transmit power increases<ref:2610. p. 5

Where the paper says it

Baseline-4 (Balanced UserTarget Centric): active TPAs are selected near the midpoint between the user and target to balance communication and sensing performance. 4 compares the communication rate of JDPABO with the baseline schemes as the transmit power increases.

03371#pg6>. JDPABO consistently achieves the highest rate by jointly optimizing transmit beamforming and TPA/RPA activation based on the user and sensing channels<ref:2610. p. 5
Where the paper says it

4 compares the communication rate of JDPABO with the baseline schemes as the transmit power increases. JDPABO consistently achieves the highest rate by jointly optimizingtransmitbeamformingandTPA/RPAactivation based on the user and sensing channels.

03371#pg6>. The target-centric scheme performs closest to JDPABO, as activating TPAs near the target improves illumination and facilitates satisfaction of the sensing SNR constraint<ref:2610.03371#pg6>. The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination<ref:2610. p. 5
Where the paper says it

The target-centric scheme performs closest to JDPABO, as activating TPAs nearthetargetimprovesilluminationandfacilitatessatisfaction of the sensing SNR constraint. The balanced user-target centric scheme provides a less favorable communicationsensing balance, while the user-centric scheme improves the user link at the expense of target illumination.

03371#pg6>. The fixed activation scheme performs worst due to its inability to adapt the antenna activation to the user-target geometry<ref:2610.03371#pg6>.

--- Page 4 ---

Problem (28) is convex and can be solved efficiently using standard convex optimization solvers<ref:2610.03371#pg5>. The overall AO algorithm for solving the proposed joint discrete pinching-antenna activation and beamforming optimization (JDPABO) problem is summarized in Algorithm 1<ref:2610. p. 4

Where the paper says it

Problem (28) is convex and can be solved efficiently using standard convex optimization solvers. The overall AO algorithm for solving the proposed joint discrete pinching-antenna activation and beamforming optimization (JDPABO) problem is summarized in Algorithm 1.

p. 4
Where the paper says it

Problem (28) is convex and can be solved efficiently using standard convex optimization solvers. The overall AO algorithm for solving the proposed joint discrete pinching-antenna activation and beamforming optimization (JDPABO) problem is summarized in Algorithm 1.

03371#pg5>.

--- Page 5 ---

The overall AO algorithm for solving the proposed joint discrete pinching-antenna activation and beamforming optimization (JDPABO) problem is summarized in Algorithm 1<ref:2610.03371#pg5>. The resulting beamforming vector w is then used in the antenna activation update<ref:2610. p. 3

Where the paper says it

(19b) Since (19) is a convex problem, any standard convex optimization solver can be invoked to solve it. The resulting beamforming vector w is then used in the antenna activation update.

03371#pg5>.

--- Page 5 ---

The resulting beamforming vector w is then used in the antenna activation update<ref:2610.03371#pg5>. The overall AO algorithm for solving the proposed joint discrete pinching-antenna activation and beamforming optimization (JDPABO) problem is summarized in Algorithm 1<ref:2610.03371#pg5>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Joint Discrete Pinching-Antenna Activation and Beamforming Optimization (JDPABO) algorithm can be implemented to jointly optimize transmit beamforming vector w and sparse TPA/RPA activation patterns a and b, leading to a computationally tractable solution for the highly nonconvex problem.

  2. The improved system can achieve communication rate maximization while satisfying constraints on transmit power, antenna selection sparsity, and minimum required radar SNR by solving the decomposed subproblems iteratively.

  3. The JDPABO approach enables the system to effectively balance communication and sensing performance, demonstrating that it approaches continuous-placement performance at low sensing SNR requirements and outperforms fixed activation schemes with sparse PA activation.

  4. By incorporating successive convex approximation (SCA) within the alternating optimization framework, the system can handle the nonconvex constraints related to achievable rate and radar SNR more accurately than standard methods.

  5. The final optimized system can adapt its antenna activation patterns to user-target geometry, as shown in simulations where The target-centric scheme performs closest to JDPABO, leading to superior performance compared to fixed or balanced schemes.

Abstract

Pinching-antenna systems (PASS) offer flexible radiation points for integrated sensing and communication (ISAC), but existing designs largely assume continuous antenna placement, which may be impractical with pre-installed hardware. We investigate a discrete-activation multi-waveguide PASS-ISAC system that selects sparse transmit and receive pinching antennas (TPAs/RPAs) from predefined locations. We formulate a communication-rate maximization problem by jointly optimizing beamforming and TPA/RPA activation under transmit-power, activation, and sensing signal-to-noise ratio (SNR) constraints. To solve this nonconvex problem, we develop a low-complexity joint discrete pinching-antenna activation and beamforming optimization (JDPABO) algorithm based on alternating optimization, successive convex approximation, and reweighted 1 minimization. Simulations show that JDPABO approaches continuous-placement performance at low sensing SNR requirements and outperforms fixed activation schemes with sparse PA activation.

Related papers