Sparse Channel Estimation and Signal Recovery for Reduced-PAPR Visible Light Optical OFDM Systems Relying on Bayesian Learning
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.
Rosa: We're looking at the paper: "Sparse Channel Estimation and Signal Recovery for Reduced-PAPR Visible Light Optical OFDM Systems Relying on Bayesian Learning".
Dev: Here's the gist of the paper. A sophisticated multipath channel impulse response (CIR) estimator is proposed, followed by sparse frequency-domain (FD) signal detection, which harnesses the simultaneous-sparsity innate in the multipath CIR and FD signals across measurement vectors, conceived for optical orthogonal frequency division multiplexing (O-OFDM) utilized for visible light communication (VLC) systems having reduced peak-to-average power ratio (PAPR) System Models The paper derives the input-output relationships for the asymmetrically clipped optical OFDM (ACO-OFDM) as well as for the direct currentbiased optical OFDM (DCO-OFDM) systems The DCO-OFDM system model involves a serial bit sequence of a single OFDM block having M subcarriers converted to complex-valued symbols via QAM, and the real-valued TD signal is determined using the M-point inverse fast Fourier transform (IFFT) The ACOOFDM system model features data symbols exclusively allocated to the odd subcarriers among the initial M/2 subcarriers, resulting in an effective number of subcarriers that carry information of M/4 Channel Modeling and Sparsity Exploitation The multipath VLC channel is modeled as a discrete-time system where the received signal after the FFT output is given by y˜k = h˜k x˜k + n˜k, k = 0, 1,..., M − 1 The multipath VLC channel can be expressed as h(n) = L Xh−1 l=0 h(l)δ n − ν(l) The normalized samples of the TD multipath VLC CIR are given by (9), which models the sparse multipath VLC CIR Proposed Estimation Techniques The authors propose several techniques to exploit sparsity, including an orthogonal matching pursuit (OMP)-based technique called groupsparse OMP (GOMP) which capitalizes on the group-sparsity in the delay domain of the CIR across measurement vectors Additionally, an advanced group-sparse multipath CIR estimation technique based on a groupsparse Bayesian learning (GBL) approach is put forth, which considerably reduces the pilot overhead A low complexity version of GBL, termed LCGBL, is also developed to reduce the computational cost of GBL significantly Performance and Comparison Simulations demonstrate that despite its reduced pilot overhead, the proposed GBL technique outperforms the other conventional and sparse CE schemes in terms of its bit error-rate (BER), outage probability (OP), and normalized mean-squareerror (NMSE) The GBL approach achieves significantly lower NMSE than the OMP, standard SMVbased BL, OMP, FOCUSS, LMMSE, and LS methods The proposed GBL-based technique produces the best NMSE for the chosen values of parameters of ρ and L A novel GBL-based technique has been conceived for the estimation of group-sparse multipath CIR and SR of the FD OOFDM symbols in an IM/DD-based VLC system The proposed method was then harnessed in ACO-OFDM and DCO-OFDM systems, and it led to a substantial reduction in the pilot overhead The GBL-assisted sparse recovery method advocated is perfectly suited for the O-OFDM system, since it enhances the quality of CSI estimation, resulting in overall superior performance in terms of the NMSE, BER, NMSEL, and OP metrics The NMSE of the GBL was also shown to closely match the BCRLB performance bound Computational Efficiency The complexity of the GBL-based sparse CE scheme is on the order of O(L cubed hL 3), which is dominated by an inversion of an LhL×LhL matrix Likewise, the LCGBL-based sparse CE scheme incurs a complexity of O(L cubed h) due to the inversion of an Lh × Lh matrix In contrast, the worst-case complexity of the GOMP algorithm scales as O(L cubed (NPz) 3), since an intermediate LS estimate must be computed at each iteration The LCGBL method provides an attractive tradeoff, offering both competitive performance and reduced computational burden Future Directions A systematic comparison with recent DL-based sparse estimation methods for VLC is an interesting and meaningful direction for future work The paper concludes that the GBL-based technique possesses the smallest region of the polygon, indicating its preeminent performance The GBL-assisted sparse recovery method is perfectly suited for the O-OFDM system, since it enhances the quality of CSI estimation, resulting in overall superior performance in terms of the NMSE, BER, NMSEL, and OP metrics The paper also suggests that a comprehensive performance visualization of the three techniques is presented in Fig.
Title and authors: Rosa: So we're looking at this paper now, "Sparse Channel Estimation and Signal Recovery for Reduced-PAPR Visible Light Optical OFDM Systems Relying on Bayesian Learning." It’s essentially tackling the problem of estimating the channel in these optical systems and then recovering the signal from that estimate.
Dev: Right. The title tells us two main things: first, they are doing sparse channel estimation, which is dealing with channels that have very few significant paths, and second, they are using Bayesian Learning to do the signal recovery part.
Rosa: Exactly. And what makes this interesting for us right now is that it’s specifically designed for optical orthogonal frequency division multiplexing, or O-OFDM systems used in visible light communication or VLC where we're trying to keep the peak-to-average power ratio low, which is a big deal for energy efficiency.
Taro: When you mention reduced PAPR, I wonder if this sparsity assumption holds up when the optical channel itself has complex behavior that isn't perfectly sparse in time.
Dev: That’s a fair question, Taro. The paper starts by modeling the input output relationships for two main variants: asymmetrically clipped optical OFDM, or ACO-OFDM, and direct current-biased optical OFDM, or DCO-OFDM. These are the dominant ways we structure these O-OFDM systems in VLC today.
Rosa: And these two variants have some specific differences you should know about. The DCO-OFDM system uses a serial bit sequence of a single OFDM block with M subcarriers converted to complex symbols via QAM, and the real valued time domain signal is determined using an M point inverse fast Fourier transform, or IFFT.
Dev: While the DCO-OFDM has that structure, ACOOFDM achieves unipolarity by trimming those bipolar signals at zero to transmit only the positive components. Meanwhile, it uses half of the odd subcarriers for data transmission compared to the DCOOFDM which uses only half of its subcarriers for transmitting symbols.
Taro: So, when we look at how they model the channel itself, they are using a discrete time system where after an FFT output you get y tilde k equal to h tilde k times x tilde k plus noise n tilde k for all values of k from zero to M minus one.
Rosa: Which leads into their description of the multipath VLC channel as h(n) equal to L times Xh minus one l equals zero h l delta n minus nu l where they model the normalized samples of the time domain channel impulse response. This models a sparse multipath VLC CIR, which is what they are trying to exploit.
Dev: They then introduce several traditional benchmarking methods for channel estimation, like linear minimum mean square error or LMMSE, and least square or LS methods, followed by an orthogonal matching pursuit method that is capable of exploiting the sparsity in the multipath.
The paper's summary: Rosa: So what's the core contribution here? The paper proposes a sophisticated approach that combines two main steps: first, proposing this multipath channel impulse response estimator, and second, following it up with sparse frequency-domain signal detection.
Dev: Basically, the whole idea is to harness the simultaneous sparsity that exists in both the time domain channel impulse response and the frequency domain signals across all measurement vectors. This is conceived specifically for O-OFDM utilized in VLC systems where we need reduced PAPR.
Taro: I’m curious about how they handle those different modulation schemes, ACO-OFDM and DCO-OFDM. Does their estimation technique work equally well for both?
Rosa: They derive the input output relationships for both of them from the beginning, which means their proposed method is designed to be versatile enough to handle both ACO-OFDM and DCO-OFDM systems.
Dev: The paper then introduces several techniques to exploit that sparsity, including an orthogonal matching pursuit based technique called groupsparse OMP, which capitalizes on the group sparsity in the delay domain of the channel across different measurement vectors.
Taro: Groupsparse OMP sounds like it’s trying to find a structure in how the delays are clustered rather than just finding sparse taps individually. Does that mean it’s exploiting some kind of correlation between measurements?
Rosa: Exactly. And on top of that, they put forth an advanced group-sparse multipath CIR estimation technique based on a groupsparse Bayesian learning approach, or GBL, which is designed to considerably reduce the pilot overhead we usually have in these systems.
Dev: And then they developed a low complexity version of GBL called LCGBL to cut down the computational cost significantly while keeping most of the performance benefits.
The paper's improvements: Rosa: The main improvement they highlight is that despite reducing pilot overhead, their proposed GBL technique outperforms other conventional and sparse channel estimation schemes in terms of bit error rate, outage probability, and normalized mean square error.
Dev: Specifically, the GBL approach achieves significantly lower normalized mean square error than the orthogonal matching pursuit method, standard minimum variance based Bayesian learning methods, OMP methods, FOCUSS, LMMSE methods, least square methods also.
Taro: Lower MSE is good for performance metrics but what about the practical reality? The paper focuses on these simulation results with specific parameter values for rho and L. Does that mean it works well in real-world conditions where those parameters might not be perfectly tuned?
Rosa: They show that the GBL approach produces the best normalized mean square error for those specific chosen values of rho and L, which suggests a very strong performance bound under those conditions.
Dev: The paper also states that this proposed GBL-based technique produces an NMSE that closely matches the BCRLB performance bound, which is a theoretical limit on how good we can possibly get. That’s quite a strong claim for a recovery method.
Taro: If it matches the bound, does that mean it’s not just lucky in the simulation? What about when the world misbehaves and those parameters shift unexpectedly?
Rosa: The paper doesn't explicitly address robustness outside of those tested parameters, but they emphasize that this enhanced CSI estimation quality results in overall superior performance across bit error rate, NMSEL, and outage probability metrics.
Conclusion: Dev: So to wrap up on the "Sparse Channel Estimation and Signal Recovery for Reduced-PAPR Visible Light Optical OFDM Systems Relying on Bayesian Learning," the paper proposes a novel GBL technique for estimating group-sparse multipath channel impulse response and signal recovery of the frequency domain OFDM symbols.
Rosa: And they apply this to ACO-OFDM and DCO-OFDM systems, which leads to a substantial reduction in pilot overhead while enhancing the quality of CSI estimation.
Taro: From my view, it’s interesting that they focused on reducing pilot overhead specifically because in VLC systems, every extra pilot signal we send takes up valuable bandwidth that could be used for actual data transmission.
Dev: I agree. And the complexity discussion is important here; they show that the low complexity version, LCGBL, has a computational cost of O(L cubed h), which is dominated by inverting an Lh times Lh matrix.
Rosa: That’s much better than some other methods, and it’s competitive with the groupsparse OMP method which scales as O(L cubed (NPz) cubed).
Taro: The paper also notes a limitation, and they mention that a comprehensive performance visualization of the three techniques is presented in a figure. I wonder what that visualization actually shows us about when one technique fails versus another.
Dev: They also state that the GBL-based technique possesses the smallest region of the polygon, which indicates its preeminent performance among all tested methods. It’s clearly designed to enhance CSI estimation quality for O-OFDM systems.
Rosa: Overall, this work suggests that Bayesian learning can be a very effective tool when you are dealing with structured sparsity in complex channel and signal data for optical communication applications like VLC. We'll keep an eye on how this translates to real-world deployment outside of the lab.
Shubham Saxena, Suraj Srivastava, Aditya K. Jagannatham, Lajos Hanzo
Indian Institute of Technology Kanpur · Indian Institute of Technology Jodhpur · University of Southampton
eess.SP
Submitted: 2026-09-14
Updated: 2026-11-03
Journal ref: IEEE Transactions on Vehicular Technology (Early Access), 2026
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 83/100
The gist: A sophisticated multipath channel impulse response (CIR) estimator is proposed, followed by sparse frequency-domain (FD) signal detection…
Key concepts
- Group-Sparse Bayesian Learning (GBL)
- A novel estimation technique that exploits the simultaneous sparsity found in the delay domain of a multipath channel across multiple measurement vectors. It uses Bayesian learning to estimate sparse channel vectors, leading to a notable reduction in required pilot overhead.
- ACO-OFDM and DCO-OFDM
- These are two specific optical OFDM system models analyzed. ACO-OFDM allocates data symbols only to odd subcarriers, while DCO-OFDM uses a serial bit sequence with M subcarriers converted via QAM to determine the real TD signal using an inverse fast Fourier transform.
- Multipath VLC Channel Modeling
- The channel is modeled as a discrete-time system where the received signal after an FFT output is related to the input by y˜k = h˜k x˜k + n˜k. The multipath nature of Visible Light Communication (VLC) channels is captured by modeling the channel impulse response h(n) as a sparse sequence.
- Low Complexity GBL (LCGBL)
- A simplified version of GBL designed to reduce computational cost. It achieves this by replacing the inversion of a large matrix with the inversion of two smaller matrices, resulting in a complexity of O(L^3 h), offering competitive performance with reduced computational burden.
Terminology
Summary
A sophisticated multipath channel impulse response (CIR) estimator is proposed, followed by sparse frequency-domain (FD) signal detection, which harnesses the simultaneous-sparsity innate in the multipath CIR and FD signals across measurement vectors, conceived for optical orthogonal frequency division multiplexing (O-OFDM) utilized for visible light communication (VLC) systems having reduced peak-to-average power ratio (PAPR)
System Models
The paper derives the input-output relationships for the asymmetrically clipped optical OFDM (ACO-OFDM) as well as for the direct currentbiased optical OFDM (DCO-OFDM) systems The DCO-OFDM system model involves a serial bit sequence of a single OFDM block having M subcarriers converted to complex-valued symbols via QAM, and the real-valued TD signal is determined using the M-point inverse fast Fourier transform (IFFT) The ACOOFDM system model features data symbols exclusively allocated to the odd subcarriers among the initial M/2 subcarriers, resulting in an effective number of subcarriers that carry information of M/4
Channel Modeling and Sparsity Exploitation
The multipath VLC channel is modeled as a discrete-time system where the received signal after the FFT output is given by y˜k = h˜k x˜k + n˜k, k = 0, 1,..., M − 1 The multipath VLC channel can be expressed as h(n) = L Xh−1 l=0 h(l)δ n − ν(l) The normalized samples of the TD multipath VLC CIR are given by (9), which models the sparse multipath VLC CIR
Proposed Estimation Techniques
The authors propose several techniques to exploit sparsity, including an orthogonal matching pursuit (OMP)-based technique called groupsparse OMP (GOMP) which capitalizes on the group-sparsity in the delay domain of the CIR across measurement vectors Additionally, an advanced group-sparse multipath CIR estimation technique based on a groupsparse Bayesian learning (GBL) approach is put forth, which considerably reduces the pilot overhead A low complexity version of GBL, termed LCGBL, is also developed to reduce the computational cost of GBL significantly
Performance and Comparison
Simulations demonstrate that despite its reduced pilot overhead, the proposed GBL technique outperforms the other conventional and sparse CE schemes in terms of its bit error-rate (BER), outage probability (OP), and normalized mean-squareerror (NMSE) The GBL approach achieves significantly lower NMSE than the OMP, standard SMVbased BL, OMP, FOCUSS, LMMSE, and LS methods The proposed GBL-based technique produces the best NMSE for the chosen values of parameters of ρ and L
Summary and Conclusion
A novel GBL-based technique has been conceived for the estimation of group-sparse multipath CIR and SR of the FD OOFDM symbols in an IM/DD-based VLC system The proposed method was then harnessed in ACO-OFDM and DCO-OFDM systems, and it led to a substantial reduction in the pilot overhead The GBL-assisted sparse recovery method advocated is perfectly suited for the O-OFDM system, since it enhances the quality of CSI estimation, resulting in overall superior performance in terms of the NMSE, BER, NMSEL, and OP metrics The NMSE of the GBL was also shown to closely match the BCRLB performance bound
Computational Efficiency
The complexity of the GBL-based sparse CE scheme is on the order of O(L cubed hL 3), which is dominated by an inversion of an LhL×LhL matrix Likewise, the LCGBL-based sparse CE scheme incurs a complexity of O(L cubed h) due to the inversion of an Lh × Lh matrix In contrast, the worst-case complexity of the GOMP algorithm scales as O(L cubed (NPz) 3), since an intermediate LS estimate must be computed at each iteration The LCGBL method provides an attractive tradeoff, offering both competitive performance and reduced computational burden
Future Directions
A systematic comparison with recent DL-based sparse estimation methods for VLC is an interesting and meaningful direction for future work The paper concludes that the GBL-based technique possesses the smallest region of the polygon, indicating its preeminent performance The GBL-assisted sparse recovery method is perfectly suited for the O-OFDM system, since it enhances the quality of CSI estimation, resulting in overall superior performance in terms of the NMSE, BER, NMSEL, and OP metrics The paper also suggests that a comprehensive performance visualization of the three techniques is presented in Fig.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Group sparse Bayesian Learning (GBL) enables estimation of group-sparse channel vectors by exploiting
the concatenation of a concatenated multipath VLC CIR’s simultaneous groupsparsity across all measurement vectors,
which leads to anotable pilot overhead reduction.
This allows the AI system to achieve superior performance in terms ofOP, BER, NMSE, and NMSEL metrics
compared to existing methods. -
Low complexity GBL (LCGBL) reduces computational cost by replacing the inversion of a large-dimensional matrix with the inversion of two smaller matrices, leading to a complexity of O(L cubed h), which provides a
competitive performance and reduced computational burden.
This makes the system more practical for real-time deployment. -
The proposed GBL and LCGBL techniques can be harnessed in ACO-OFDM and DCO-OFDM systems to lead to a
substantial reduction in the pilot overhead,
enhancing bandwidth efficiency while maintaining a desired level of estimation accuracy.
Related papers
- Open-H-RF: A Large-Scale Ultrasound Raw Channel Dataset Initiative
- Scalable Attention for 5G NR Channel Estimation
- Low-Altitude Wireless Networks: A Comprehensive Survey
- Sensing-Assisted OFDM with Index Modulation: A Waveform for Optical Wireless Integrated Communication and Localisation
- Iteration-Free Candidate Pruning and an Index-Domain VLSI Architecture for Sort-Free MIMO Box Decoding up to 1024-QAM
- A Foundation Model for Large-Scale Wireless Network Planning, Operation and Optimization