Optimizing GEDI Simulator Configuration for European Temperate Forests
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.
Rosa: We're looking at the paper: "Optimizing GEDI Simulator Configuration for European Temperate Forests".
Dev: Here's the gist of the paper. Accurate estimation of aboveground biomass density is essential for quantifying forest carbon stocks, and this study compares simulated GEDI waveforms against real observations in European temperate forests to optimize calibration methods The int–a3 configuration reduces the mean absolute bias across the full RH profile from 0.69 m to 0.44 m in leaf-on conditions and from 1.28 m to 0.40 m in leaf-off conditions for high-sensitivity shots Pruning redundant reasoning tokens The study compares approximately 9,500 pairs of observed and simulated GEDI relative height (RH) profiles across French forests using the national airborne LiDAR program as input The researchers separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing algorithm against the ALS reference Under the baseline configuration, the mean absolute bias across the full RH profile reaches 0.69 m in leaf-on and 1.28 m in leaf-off conditions Switching to intensity-based return weighting and selecting the a3 L2A algorithm reduces these biases to 0.44 m and 0.40 m respectively The a3 algorithm also achieves near-unbiased ground detection (-0.03 m versus-0.88 m for the default), directly reducing a previously overlooked source of error How the training signal is built The simulation framework models each virtual GEDI footprint as a combination of spatial weighting, return-specific weighting, optional sampling-density normalization, vertical convolution, and instrument sampling The process involves several steps: 1.
Rosa: Spatial Weighting assigns each ALS point a weight based on its position relative to the center of the footprint using a Gaussian footprint model 2.
Dev: Return-specific weighting implements three options: count method, frac method, and intensity method 3.
Rosa: Density normalization corrects for horizontal sampling heterogeneity by normalizing by pulse density rather than point density 4.
Paper summary: Rosa: So, this paper, "Optimizing GEDI Simulator Configuration for European Temperate Forests," it's looking at how we use these simulators to get aboveground biomass estimates from GEDI data when you don't have real field inventory right there.
Dev: Right, it’s about comparing simulated GEDI waveforms against real observations in European temperate forests to figure out the best way to set up those calibration methods. The big thing they're tackling is how much error we have in those estimates for carbon stocks.
Rosa: What they claim is that by tweaking the setup, they can really bring down the mean absolute bias across the whole relative height profile. They show this happens in both leaf-on and leaf-off conditions for high-sensitivity shots.
Dev: Specifically, they say switching to intensity-based return weighting and using their a3 L2A algorithm cuts that bias way down: from zero point sixty-nine meters to point forty-four meters in the leaf-on case, and from one point two eight meters down to zero point forty meters in the leaf-off case for high sensitivity shots.
Rosa: That reduction is pretty significant, especially because it fixes a problem they call ground detection bias, which was previously overlooked when comparing GEDI algorithms against that reference data from airborne LiDAR.
Dev: And they also found something else important: the a3 algorithm actually achieves near-unbiased ground detection, coming in at negative zero point zero three meters compared to negative zero point eight eight meters for the default setup.
Rosa: That's a big deal because that ground detection bias was a major source of error they were seeing. It’s not just about the height measurement itself; it's about where the simulator thinks the ground is located.
Dev: Exactly, and this whole process of building the simulation framework involves spatial weighting, return-specific weighting, density normalization, vertical binning with pulse convolution to get a noise-free waveform. It’s a detailed way of modeling what GEDI actually measures.
Rosa: The authors really emphasize that the main gain isn't just picking one algorithm; it’s switching the return weighting strategy from count to intensity. That method weights each return by its recorded ALS intensity, which they argue more faithfully represents the scattering surfaces GEDI actually detects.
Dev: They point out that this is physically more realistic because bare soil produces a concentrated, high-amplitude ground return due to the absence of volume scattering, and this method reconstructs a ground peak whose amplitude and width match the real GEDI ground return better.
Paper summary: Rosa: So, what does this mean for us? It means they found an optimal configuration, int-a3, that maximizes how well their models calibrated on simulated metrics transfer to actual GEDI observations.
Dev: They say that the int-a3 setup removes most of the seasonal asymmetry that messed up the results in their baseline setup, making leaf-off acquisitions as reliable as leaf-on ones across most of the vertical profile.
Rosa: That reliability for leaf-off shots is a major step forward. It means we can start using those leaf-off ALS acquisitions in biomass calibration workflows and include them in larger scale inference studies.
Dev: They also confirmed that this int option, weighting by intensity, provides a physically more realistic representation of the scattering surfaces GEDI actually detects and that this improvement holds across different sensitivity classes and forest types.
Rosa: The only exception they mentioned is at the upper percentiles, specifically the relative height ninety-eight point eight in leaf-off low-sensitivity shots, where all weighting methods still show a positive bias of about two meters.
Dev: That exception happens because GEDI’s noise thresholding causes the detected canopy top to be placed lower than the true top when the signal to noise ratio is low and canopy cover is high. So, they’ve clearly mapped out where the limitations are.
Rosa: Considering this paper, "Optimizing GEDI Simulator Configuration for European Temperate Forests," it really shows how much fine-tuning in a simulation setup can impact the real-world utility of satellite data products like GEDI.
Dev: The authors recommend systematically using that int weighting for large scale GEDI simulation studies, especially when you need to incorporate leaf-off ALS data to get a bigger sample size for calibration.
Rosa: So, the implication here is that we can build biomass models using simulated metrics derived from either leaf-on or leaf-off ALS acquisitions, which substantially increases the pool of available ALS data for calibration.
Dev: This paper suggests that int-a3 is a practical default configuration for GEDI simulation studies in European temperate forests because it works with modern high density ALS data and supports the transferability of results to other European contexts.
Rosa: It confirms the value of using simulators to understand how sensitive GEDI is to forest structure, which is crucial when you’re trying to calibrate biomass models accurately.
Dev: So, overall, this work shows that by applying noise thresholds that exclude low energy regions and then computing the cumulative energy profile between those bounds, we can transform the raw waveforms into a relative height profile.
Paper summary: Rosa: And they define relative height metrics as the heights where specific percentiles like twenty-five point zero percent or fifty point zero percent of that cumulative energy are reached, expressed relative to the detected ground elevation. That's how they derive their final RH profile.
Dev: It’s interesting because GEDI operates two beam types, full power beams and coverage beams, and they deal with the constraint that GEDI’s sampling remains sparse in both space and time. Footprints are spaced about sixty meters apart along track and six hundred meters across track, and the revisit frequency over any given inventory plot location is limited.
Rosa: So, while they fix the simulation setup for European forests, they also highlight that GEDI’s inherent sampling limitations are a major constraint when you try to do local calibration or validation with field inventory plots.
Dev: That's what the paper points out as a major constraint for local calibration and validation work. It sets the context for why these simulation improvements are so necessary.
Rosa: The main thing this paper tells us is that optimizing the simulator configuration, specifically using int-a3, can make leaf-off GEDI shots much more reliable and usable in biomass workflows.
Dev: That reliability comes from better handling waveform modeling differences and ground detection bias compared to the baseline configuration they tested.
Rosa: So, for someone listening who just wants the big picture, this paper is about making sure that when we use these sparse GEDI measurements to estimate carbon stocks, we're using the most accurate tools possible.
Rosa: So to wrap up "Optimizing GEDI Simulator Configuration for European Temperate Forests," the authors are basically recommending the int-a3 configuration as a practical default for simulation studies in this region using modern high density ALS data.
Dev: They found that this setup cuts the mean absolute bias across the full relative height profile down to point forty-four meters in leaf-on and one point zero zero meters in leaf-off conditions for high sensitivity shots.
Rosa: That means they’ve successfully made leaf-off acquisitions as reliable as leaf-on ones across most of the vertical profile, which is a big deal because it opens the door to using those shots in large scale inference.
Dev: It confirms that the int option, weighting by intensity, provides a physically more realistic representation of GEDI’s scattering surfaces than counting returns.
Rosa: And this correction helps remove most of the seasonal asymmetry that was messing things up in their baseline setup, which is why it’s so important for biomass calibration.
Conclusion: Rosa: So, this paper is about optimizing the GEDI simulator setup specifically for European temperate forests to get better biomass estimates.
Dev: Yeah, they look at how we simulate those GEDI waveforms and compare them to real observations in French forests.
Rosa: The core idea is that by changing a few settings, you can really reduce the errors in estimating aboveground biomass density.
Dev: They found that using the int-a3 configuration cuts the mean absolute bias way down across both leaf-on and leaf-off conditions for high sensitivity shots.
Rosa: That means they made those leaf-off measurements as reliable as the ones taken when there are leaves on, which is a big deal for how we use this data.
Dev: It's about making sure that the model calibrated on simulated data actually works well with real GEDI observations in the field.
Rosa: The authors suggest this int-a3 setup is a practical default for simulation studies in European forests because it works well with modern high density airborne LiDAR data.
Dev: They're basically saying this configuration helps us get a more physically realistic picture of what GEDI actually detects, which is important for the whole calibration process.
Rosa: It confirms the simulator’s value for understanding how GEDI responds to forest structure when you are trying to calibrate those biomass models.
Dev: The only snag they found was at the very top, around relative height ninety-eight point eight in leaf-off low sensitivity shots, where things get a bit biased.
Rosa: That specific exception happens because of how GEDI handles noise and canopy cover at those extreme points.
Dev: So, while int-a3 is the best default for most scenarios, we still have to be careful when dealing with those very high canopy regions in low sensitivity shots.
Rosa: This work paves the way for operational use of leaf-off ALS data in biomass workflows and including leaf-off GEDI shots in large scale inference studies.
Dev: Next up, we're going to look at how this affects the actual calibration pipelines and what the next steps are for deployment.
Selim Behloul, Nikola Besic, Steven Hancock, Cedric Vega, Sylvie Durrieu, Jean-Pierre Renaud, Ibrahim Fayad, Philippe Ciais
LSCE/IPSL, CEA-CNRS-UVSQ, University Paris Saclay · University of Lorraine · Geodata Paris Institute National Geographic Institute (IGN) · School of GeoSciences, University of Edinburgh · National Centre for Earth Observation, United Kingdom · UMR TETIS, INRAE, AgroParisTech, CIRAD, CNRS, University Montpellier · Office National des Forêts RDI
eess.SP, physics.geo-ph, stat.AP, stat.CO
Submitted: 2026-09-10
Updated: 2026-10-30
Comments: Submitted to AGU Earth and Space Science (ESS). Presented at EGU General Assembly 2026, Vienna, Austria, abstract EGU26-9762. DOI: https://doi.org/10.5194/egusphere-egu26-9762
License: http://creativecommons.org/licenses/by/4.0/
Importance score: 90/100
The gist: Accurate estimation of aboveground biomass density is essential for quantifying forest carbon stocks, and this study compares simulated GEDI waveforms against real observations in European temperate…
Key concepts
- GEDI Waveform
- This refers to the signal captured by the Global Ecosystem Dynamics Investigation (GEDI) instrument. The study models how this signal is generated by combining different factors like spatial weighting, return weighting, and vertical convolution to create a simulated GEDI profile that mimics real forest structures.
- Return Weighting (int vs. count)
- This determines how much importance is given to each return signal from the LiDAR data. The 'int' method weights returns by their recorded intensity, which more accurately reflects what GEDI actually detects, improving the simulation's physical realism compared to simpler methods like 'count'.
- Ground Detection Bias
- This measures how accurately the simulated system identifies the true ground elevation from LiDAR data. The 'a3' algorithm specifically addresses this by achieving near-unbiased ground detection, correcting a significant error present in default settings that previously caused large biases.
- Leaf-on/Leaf-off Conditions
- These describe the two different states of the forest canopy—when leaves are present ('leaf-on') and when they are absent ('leaf-off'). The study found that the optimized configuration makes leaf-off acquisitions as reliable for biomass calibration as leaf-on ones, removing seasonal asymmetry.
Terminology
Summary
Accurate estimation of aboveground biomass density is essential for quantifying forest carbon stocks, and this study compares simulated GEDI waveforms against real observations in European temperate forests to optimize calibration methods The int–a3 configuration reduces the mean absolute bias across the full RH profile from 0. p. 1 manuscript submitted to Earth and Space Science
Abstract
Accurate estimation of aboveground biomass density is essential for quantifying forest carbon stocks. NASA’s GEDI mission provides valuable canopy structure data, but
its sparse sampling necessitates the use of simulators to calibrate biomass models at field
inventory locations. 69 m in leaf-on and 1. p. 0 manuscript submitted to Earth and Space Science
Optimizing GEDI Simulator Configuration for
European Temperate Forests
Selim Behloul1,2,3
, Nikola Besic2,3
, Steven Hancock4,5
, Cedric Vega2,3
, Sylvie
Durrieu6
, Jean-Pierre Renaud2,3,7
, Ibrahim Fayad1
, and Philippe Ciais1
1LSCE/IPSL, CEA-CNRS-UVSQ, Universit´e Paris Saclay, 91191 Gif-sur-Yvette, France
2Universit´e de Lorraine, G´eodata Paris, IGN, LIF, 54000 Nancy, France
3Universit´e Gustave Eiffel, G´eodata Paris, IGN, LIF, 54000 Nancy, France
4School of GeoSciences, University of Edinburgh, Edinburgh EH9 3FF, UK
5National Centre for Earth Observation, UK
6UMR TETIS, INRAE, AgroParisTech, CIRAD, CNRS, Univ Montpellier, F-34196, France
7Office National des Forˆets RDI, 54600 Villers-l`es-Nancy, France
Key Points:
• Intensity-based ALS weighting with GEDI L2A algorithm a3 reduces RH bias from
0. 44 m in leaf-on and 1. 69 m in leaf-on and 1. 28 m in leaf-off conditions. 69 m in leaf-on and 1. 28 m in leaf-off conditions. 69 m in leaf-on and 1. 28 m in leaf-off conditions. 69 m in leaf-on and 1. 28 m in leaf-off conditions.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Pruning redundant reasoning tokens
The study compares approximately 9,500 pairs of observed and simulated GEDI relative height (RH) profiles across French forests using the national airborne LiDAR program as input The researchers separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing algorithm against the ALS reference Under the baseline configuration, the mean absolute bias across the full RH profile reaches 0.69 m in leaf-on and 1.28 m in leaf-off conditions Switching to intensity-based return weighting and selecting the a3 L2A algorithm reduces these biases to 0. p. 1 28 m in leaf-off conditions. Switching to intensity-based return weighting and selecting the a3 L2A algorithm reduces
these biases to 0. 40 m respectively. The a3 algorithm also achieves near-unbiased
ground detection (-0. The a3 algorithm also achieves near-unbiased
ground detection (-0. 03 m versus -0. The a3 algorithm also achieves near-unbiased
ground detection (-0. 03 m versus -0. The a3 algorithm also achieves near-unbiased
ground detection (-0. 03 m versus -0. The a3 algorithm also achieves near-unbiased
ground detection (-0. 03 m versus -0. The a3 algorithm also achieves near-unbiased
ground detection (-0. 03 m versus -0.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
How the training signal is built
The simulation framework models each virtual GEDI footprint as a combination of spatial weighting, return-specific weighting, optional sampling-density normalization, vertical convolution, and instrument sampling The process involves several steps:
-
Spatial Weighting assigns each ALS point a weight based on its position relative to the center of the footprint using a Gaussian footprint model
-
Return-specific weighting implements three options: count method, frac method, and intensity method
-
Density normalization corrects for horizontal sampling heterogeneity by normalizing by pulse density rather than point density
-
Vertical binning aggregates weighted contributions into a vertical histogram at the instrument’s sampling resolution
-
Vertical convolution with the system pulse produces a noise-free GEDI-like waveform
Where the gains come from
The most substantial reduction in RH bias arises not from algorithm choice alone but from switching the return-weighting strategy from count to int The int method weights each return by its recorded ALS intensity, which more faithfully represents the scattering surfaces that GEDI actually detects This method reconstructs a ground peak whose amplitude and width more closely match the real GEDI ground return because bare soil produces a concentrated, high-amplitude ground return due to the absence of volume scattering Furthermore, the int–a3 combination achieves both the lowest ground detection bias and the lowest RH bias simultaneously by preserving fine structure of energy distribution
The optimal configuration for all subsequent analyses is selected as int–a3 because it maximizes the transferability of models calibrated on simulated metrics to real GEDI observations The results demonstrate that the int–a3 configuration removes most of the seasonal asymmetry that affected the baseline, making leaf-off acquisitions as reliable as leaf-on ones across most of the vertical profile This correction paves the way for operational use of leaf-off ALS acquisitions in biomass calibration workflows and for including leaf-off GEDI shots in large-scale inference
The study confirms that the int option, which weights each return by its recorded intensity, provides a physically more realistic representation of the scattering surfaces that GEDI actually detects This improvement is robust across sensitivity classes, forest types, and phenological conditions The int–a3 configuration makes leaf-off acquisitions as reliable as leaf-on ones across most of the vertical profile, except for RH98 in low-sensitivity shots
The researchers recommend the systematic use of int weighting for large-scale GEDI simulation studies, particularly when leaf-off ALS data must be incorporated to maximize the calibration sample size This implies that biomass models could be calibrated on simulated metrics derived from leaf-on or leaf-off ALS acquisitions, substantially increasing the pool of ALS data available for calibration
The findings suggest that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data This recommendation is based on comparable forest types and converging sensor standards, which support the transferability of results to other European contexts The authors suggest that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data
The study confirms the value of the simulator for understanding GEDI’s sensitivity to forest structure and for supporting the calibration of biomass models The int option, which weights each return by its recorded intensity, provides a physically more realistic representation of the scattering surfaces that GEDI actually detects Combined with the a3 L2A algorithm, which achieves near-unbiased ground detection (bias-0.03 m versus-0.88 m for the default), this configuration reduces the mean absolute bias across the full RH profile from 0. p. 1 We separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground
elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing
algorithm against the ALS reference. Under the baseline configuration, the mean absolute
bias across the full RH profile reaches 0. We separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground
elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing
algorithm against the ALS reference. Under the baseline configuration, the mean absolute
bias across the full RH profile reaches 0. We separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground
elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing
algorithm against the ALS reference. Under the baseline configuration, the mean absolute
bias across the full RH profile reaches 0. We separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground
elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing
algorithm against the ALS reference. Under the baseline configuration, the mean absolute
bias across the full RH profile reaches 0.Where the paper says it
Where the paper says it
Where the paper says it
Where the paper says it
The only notable exception is the upper percentiles (RH98) in leaf-off, low-sensitivity conditions, where all weighting methods produce a positive bias of approximately 2 m This occurs because GEDI’s noise thresholding causes the detected canopy top to be placed lower than the true top when signal-to-noise ratio is low and canopy cover is high
The study confirms that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The authors suggest that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The results confirm the value of the simulator for understanding GEDI’s sensitivity to forest structure and for supporting the calibration of biomass models The int option, which weights each return by its recorded intensity, provides a physically more realistic representation of the scattering surfaces that GEDI actually detects Combined with the a3 L2A algorithm, which achieves near-unbiased ground detection (bias-0.03 m versus-0.88 m for the default), this configuration reduces the mean absolute bias across the full RH profile from 0.69 m to 0.44 m in leaf-on conditions and from 1.28 m to 0.40 m in leaf-off conditions for high-sensitivity shots
The benefit of int–a3 is particularly pronounced under leaf-off conditions, where the seasonal bias gap nearly disappears This correction paves the way for operational use of leaf-off ALS acquisitions in biomass calibration workflows and for including leaf-off GEDI shots in large-scale inference The authors further demonstrate that low-sensitivity shots are not inherently more biased than higher-sensitivity ones
The study confirms that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The authors suggest that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The results confirm the value of the simulator for understanding GEDI’s sensitivity to forest structure and for supporting the calibration of biomass models The int option, which weights each return by its recorded intensity, provides a physically more realistic representation of the scattering surfaces that GEDI actually detects Combined with the a3 L2A algorithm, which achieves near-unbiased ground detection (bias-0.03 m versus-0.88 m for the default), this configuration reduces the mean absolute bias across the full RH profile from 0.69 m to 0.44 m in leaf-on conditions and from 1.28 m to 0.40 m in leaf-off conditions for high-sensitivity shots The benefit of int–a3 is particularly pronounced under leaf-off conditions, where the seasonal bias gap nearly disappears This correction paves the way for operational use of leaf-off ALS acquisitions in biomass calibration workflows and for including leaf-off GEDI shots in large-scale inference The authors further demonstrate that low-sensitivity shots are not inherently more biased than higher-sensitivity ones
The study confirms that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The authors suggest that the int–a3 configuration can be recommended as a practical default for GEDI simulation studies in European temperate forests using modern high-density ALS data The results confirm the value of the simulator for understanding GEDI’s sensitivity to forest structure and for supporting the calibration of biomass models The int option, which weights each return by its recorded intensity, provides a physically more realistic representation of the scattering surfaces that GEDI actually detects Combined with the a3 L2A algorithm, which achieves near-unbiased ground detection (bias-0.03 m versus-0.88 m for the default), this configuration reduces the mean absolute bias across the full RH profile from 0.69 m to 0.44 m in leaf-on conditions and from 1.28 m to 0.
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Optimized GEDI simulation for biomass estimation can now reliably incorporate leaf-off acquisitions and low-sensitivity shots by using an intensity-based return weighting strategy combined with algorithm a3, which
reduces these biases to 0.44 m and 0.40 m respectively.
-
Improved AI systems can achieve more accurate ground detection when calibrating models by selecting the a3 L2A algorithm, as it shows
the most accurate ground elevation estimates, with a near-zero mean bias of -0.03 m
compared to the default configuration's-0.88 m.
-
Biomass models can be calibrated using simulated metrics that are then applied to real GEDI observations with reduced systematic offsets because the optimal configuration
is the one that maximizes the transferability of models calibrated on simulated metrics to real GEDI observations.
-
The AI system can better account for variations in forest structure by using intensity-based weighting, as this method
translates these variations into a more faithful representation of the scattering surfaces that GEDI actually detects
compared to the count method which treats every return as an equal contributor. -
The system can achieve near-unbiased ground detection relative to ALS when an appropriate algorithm is selected, as it shows
a3 shows the smallest overall residual relative to ALS ground (bias-0.03 m).
-
Biomass estimation accuracy can be enhanced by using the int weighted configuration, which
reduces the mean absolute bias across the full RH profile from 0.69 m to 0.44 m in leaf-on conditions and from 1.28 m to 0.40 m in leaf-off conditions for high-sensitivity shots.
Abstract
Accurate estimation of aboveground biomass density is essential for quantifying forest carbon stocks. NASA's GEDI mission provides valuable canopy structure data, but its sparse sampling necessitates the use of simulators to calibrate biomass models at field inventory locations. The widely used simulator of Hancock et al. (2019) emulates GEDI waveforms from airborne LiDAR point clouds, yet it has never been validated over European temperate forests. Here, we compare approximately 8,100 pairs of observed and simulated GEDI relative height (RH) profiles across French forests using the national airborne LiDAR program as input. We separate two sources of error: waveform modeling differences, assessed by referencing both simulated and real RH metrics to a common ALS-derived ground elevation, and ground detection bias, evaluated by comparing each GEDI L2A processing algorithm against the ALS reference. Under the baseline configuration, the mean absolute bias across the full RH profile reaches 0.67 m in leaf-on and 1.20 m in leaf-off conditions. Switching to intensity-based return weighting and selecting the a3 L2A algorithm reduces these biases to 0.43 m and 0.42 m respectively. The a3 algorithm also achieves near-unbiased ground detection (+0.04 m versus-0.82 m for the default), directly reducing a previously overlooked source of error. We also show that leaf-off acquisitions and low-sensitivity shots, both typically excluded from standard biomass products, are simulated as reliably as their counterparts, substantially expanding the potential calibration and inference datasets.
Related papers
- Open-H-RF: A Large-Scale Ultrasound Raw Channel Dataset Initiative
- Scalable Attention for 5G NR Channel Estimation
- Low-Altitude Wireless Networks: A Comprehensive Survey
- Sensing-Assisted OFDM with Index Modulation: A Waveform for Optical Wireless Integrated Communication and Localisation
- Iteration-Free Candidate Pruning and an Index-Domain VLSI Architecture for Sort-Free MIMO Box Decoding up to 1024-QAM
- A Foundation Model for Large-Scale Wireless Network Planning, Operation and Optimization