Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip

arXiv:2608.08049 · eess.SY, cs.RO, cs.SY · Submitted 2026-08-08 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: We're looking at the paper: "Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip".

Dev: Here's the gist of the paper. Trajectory tracking for nonholonomic mobile robots subject to severe multiplicative wheel slip is addressed by a parameter-dependent linear matrix inequality (LMI) framework that simultaneously establishes semi-global differential input-to-state stability, a prescribed exponential decay rate, regional pole placement, and a gain-bounded feedback proxy for actuator-limited operation The central contribution is an explicit upper bound on the additive disturbance induced by bounded multiplicative slip in the Kanayama moving-frame error coordinates System Modeling and Error Dynamics The paper models a unicycle-type kinematic vehicle with world-frame pose and control inputs, deriving the standard Kanayama error dynamics which are then perturbed by a multiplicative wheel slip mechanism where actual velocities deviate from commanded values through a factor of (1 + σv(t)) and (1 + σω(t)) The error dynamics under slip are shown to be reformulated as the nominal dynamics perturbed by an additive disturbance d(t), which bridges the multiplicative slip problem to the additively perturbed cascade The scheduling parameter ρ = (vr, ωr) is assumed to take values in a known convex polytope P, and its affine dependence on the reference velocities ensures that linear constraints on A(ρ) over P can be enforced by imposing them at the four vertices alone Stability Framework and Synthesis The stability analysis employs a semi-global differential input-to-state stability (D-ISS) concept, defined by a storage function Vδ(δe, ρ) satisfying V˙ + 2αV − γ2/2 δd2 ≤ 0 The main synthesis theorem establishes the closed-loop matrix Acl(ρ) = A(ρ) + BK(ρ), where K(ρ) is the parameter-scheduled gain introduced in u = K(ρ)e, and it requires finding symmetric matrices W0, W1, W2 and Y0, Y1, Y2 such that several matrix inequalities hold simultaneously at every grid point (rho(k), rho˙(l)) Slip-to-Disturbance Characterization Lemma 1 establishes the slip-to-disturbance bound, showing that the error dynamics under multiplicative slip admit an equivalent additive disturbance representation e˙ = A(ρ) e + B u + φ(e, ρ) + dslip(t), where the disturbance satisfies a pointwise bound dslip(t) ≤ δmax The explicit constant δmax is derived as δmax = σ¯q (vmax + K˜maxR)2 + (ωmax + K˜maxR)2 This lemma bridges the physical slip model and the convex LMI framework developed in Section 5 Numerical Validation and Robustness The numerical validation compares three controllers across six reference trajectories, six disturbance classes, and a 60-second variable-terrain test featuring six severe slip patches with bidirectional slip ratios reaching ±50% The proposed LPV design achieves a peak tracking error of 12% against the fixed-gain LMI baseline and 49% against the manual baseline on the variable-terrain scenario The controller demonstrates robustness to Gaussian sensor noise at three intensity levels, with its advantage expanding to 37.7% over Kanayama under high noise conditions The framework provides a unified and computationally efficient certification path for nonholonomic mobile robots operating across heterogeneous surface conditions The synthesis stage solves the LMI system at the sixteen polytope vertices, while the subsequent certification stage verifies the dissipation inequality on a dense parameter grid using Lemma 2 to extend the discrete certificate to the continuum The runtime cost of evaluating K(ρ) is low, scaling to an estimated 50 µs on an ARM Cortex-M7 microcontroller, making it suitable for embedded deployment The variable-terrain helical-path benchmark is recommended as a standard stress test before deployment to any new environment The framework connects the convex parameterization viewpoint for nonlinear systems with the differential contraction framework of Lohmiller and Slotine Acknowledgments The author gratefully acknowledges Prof.

Rosa: Mohammad Hassan Asemani of Shiraz University for valuable guidance and constructive technical feedback that informed the development of this work The author also thanks colleagues at the Department of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, for fruitful discussions on parameter-varying control synthesis, robust stability analysis, and slip-aware robotic systems Funding Statement The author received no specific funding for this work The author used AI tools to assist with language polishing and LaTeX formatting during the preparation of this work The MATLAB code and simulation data that support the findings of this study are available from the corresponding author upon reasonable request The author declares no competing financial or non-financial interests in relation to the work described References

1: Morin P, Samson C.

Dev: Motion control of wheeled mobile robots.

Rosa: In: Siciliano B, Khatib O, eds.

Title and authors: Rosa: So we're looking at this paper today, "Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip." It tackles a really tough problem: getting a wheeled robot to follow a path when the wheels are slipping in complicated ways.

Dev: Yeah, it’s about making sure that tracking works even when the slip isn't just some simple constant number, but something that changes depending on what you're doing and where you are. It uses this parameter-dependent linear matrix inequality framework to nail a few things at once.

Taro: The authors are Mohammad Sabouria and they’ve put this LMI approach together to handle the slip uncertainty on variable terrain surfaces, which is where things get messy in the real world.

Rosa: So what's the main idea here? Basically, they’re aiming for a set of guarantees that work across different operating conditions. They want semi-global differential input to state stability, an exponential decay rate for how fast things settle down, regional pole placement for damping and bandwidth control, and even a gain-bounded feedback proxy to keep the actuator limits in check.

Dev: That sounds like they’re trying to build a very robust controller that doesn't just work in a perfect lab setting but keeps its performance bounds even when things start going wrong. They use this parameter-dependent linear matrix inequality framework, which is pretty clever because it lets them handle the uncertainty in the slip ratio as a known parameter variation.

Taro: What I find interesting is how they connect the multiplicative slip problem to an additive disturbance representation, which seems to simplify the math a lot for their LMI setup. They show that under this model, you can reformulate the error dynamics as something that looks like it’s just a normal system with an extra disturbance term.

Rosa: That's key because it lets them use the tools of additive perturbed cascade analysis, which is well-understood in control theory. They explicitly establish an upper bound on this additive disturbance induced by bounded multiplicative slip in the Kanayama moving-frame error coordinates, which they call δmax.

Dev: And that explicit bound is what really grounds the whole stability proof. They derive that constant δmax as being dependent on the maximum wheel velocity and maximum heading rate, plus some terms involving K max and R, which gives us a concrete number for how much disturbance we can expect from bounded slip.

Title and authors: Taro: It means they’re not just saying "it's stable," they’re giving us a quantifiable measure of how much the error will be pushed around by the slip when it stays within certain bounds. That's what I care about when testing things out on uneven ground where you don't have perfect models.

Rosa: And for the practical side, they’ve got this synthesis theorem that establishes a closed-loop matrix Acl rho equals A rho plus B K rho, where the gain K kappa is scheduled based on the parameter rho. They need to find symmetric matrices W zero, W one, W two and Y zero, Y one and Y two such that several matrix inequalities hold at every grid point of rho and its derivative.

Dev: So it’s an LPV design approach where the gain K kappa is scheduled based on the parameter rho, but they’re solving for this gain using a set of coupled matrix inequalities across a whole polytope P. This allows them to enforce constraints across all those different operating points simultaneously by only checking the four vertices of that polytope.

Taro: That's neat because it avoids having to solve a massive optimization problem over the entire space, you just need to solve it at those specific points and then use some continuity argument to extend the certificate everywhere.

Rosa: They use this grid-to-continuum residual certification, which is a method they developed themselves, that bridges the gap between solving for discrete points and proving stability across the whole continuous range of parameters. It’s what makes this framework useful for variable terrain.

Dev: And they’ve also got a way to verify this stability by using Lemma two to extend the discrete certificate onto a dense parameter grid, which means they can use their LMI design at the vertices and then check it densely everywhere else using that lemma. That’s how you get from theory to something you can actually trust in real-time.

Taro: So if I'm thinking about failure modes, this suggests that even with severe slip patches, the system is designed to stay within a bounded region around the desired trajectory, as shown by Corollary two. They prove that every trajectory starting within a radius R zero will stay inside a ball of radius B bar R zero for all time.

Title and authors: Rosa: That’s really reassuring for deployment because it gives us a safety envelope, not just an asymptotic stability result where things eventually converge but might wander around forever. It means the tracking error stays bounded by something we can calculate based on our initial conditions and the system's parameters, like σp and σh.

Dev: I think that bounding the error using that specific disturbance bound δmax is a big step because it connects the physical slip mechanism directly to a formal control design tool like an LMI. It’s not just theoretical; it’s tied to physical limits on how much error can accumulate from that slip.

Taro: And when I look at the numerical validation, they tested this across six reference trajectories, six disturbance classes, and even a sixty-second variable-terrain test with six severe slip patches where the bidirectional slip ratios reached plus minus fifty percent. The results showed that their proposed LPV design achieved a peak tracking error of twelve percent against the fixed gain LMI baseline and forty-nine percent against the manual Kanayama baseline on that tough terrain scenario.

Rosa: That comparison is pretty telling because it shows a solid performance boost, especially when you look at how much better it is than the purely linear LMI approach and how much better it is than just having someone manually tune the controller for that specific difficult test.

Dev: And they also showed robustness to Gaussian sensor noise at three intensity levels, and their advantage over Kanayama under high noise conditions expanded to thirty-seven point seven percent. That suggests the structure of this LMI design actually handles noise better than the older methods we’ve been using for nonholonomic systems.

Taro: The paper also mentions that the LPV advantage on patch P five, which is a downhill section, was comparable to its performance on negative-slip patches despite those being qualitatively different physical mechanisms. That means it's not just tuned for one type of slip; it has some general capability across different types of terrain changes.

Rosa: Overall, what this paper does is provide a unified and computationally efficient certification path for nonholonomic mobile robots operating across different surface conditions. They solve the LMI system at the sixteen polytope vertices and then use Lemma two to verify that dissipation inequality on a dense parameter grid using that technique to extend it to the continuum.

Title and authors: Dev: The runtime cost of evaluating the gain K kappa is quite low, scaling to an estimated fifty microseconds on an ARM Cortex-M7 microcontroller, which means it’s actually feasible for embedded deployment on hardware you might use in a real robot. That's a big deal for real-time control loops.

Taro: I just want to push on what this means practically: this framework connects the convex parameterization viewpoint of nonlinear systems with the differential contraction framework developed by Lohmiller and Slotine, which is how we usually analyze these things for nonholonomic systems. It’s a solid theoretical foundation for getting real guarantees.

Rosa: Exactly. So to wrap up on this paper, "Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip," it gives us a robust way to design controllers that handle slip uncertainty on variable terrain by combining LMI synthesis with grid-to-continuum certification.

Dev: It provides semi-global differential input to state stability, an exponential decay rate, regional pole placement, and a gain-bounded feedback proxy for actuator limitations. The central contribution is the explicit upper bound on the additive disturbance induced by bounded multiplicative slip in the Kanayama moving-frame error coordinates.

Taro: And it gives us a way to certify trajectory containment within a certified envelope over an initial condition radius R zero, proving that every trajectory starting within that radius will stay inside B bar R zero for all time.

Rosa: This work is really useful because it gives us a unified and computationally efficient certification path for nonholonomic mobile robots operating across heterogeneous surface conditions, and the runtime cost of evaluating the gain K kappa is low enough for embedded use.

Dev: We should look at this framework as a way to build systems that are not only fast but also robust when they encounter unpredictable physical phenomena like severe wheel slip.

Taro: Yeah, maybe we can use the variable-terrain helical-path benchmark they recommend as a standard stress test before we deploy anything new in a new environment.

Rosa: That sounds like a solid plan. We’ve got this paper, and it shows how much work goes into making these systems truly reliable outside of perfect lab conditions.

The paper's summary: Rosa: So, we've seen that this paper is about using this parameter dependent linear matrix inequality framework to design controllers for wheeled robots that are slipping under different conditions. It’s not just trying to keep them on track when everything is perfect; it’s building something that works even when the world misbehaves with those slip changes.

Dev: Yeah, precisely, and what they nail here is a few things at once: semi global differential input to state stability, an exponential decay rate for how fast the error settles down, regional pole placement for damping and bandwidth control, and even a gain bounded feedback proxy to keep the actuator limits in check.

Taro: What I find really interesting is how they take that multiplicative slip problem—where the actual wheel speed deviates from what you command because of those factors sigma v and sigma omega—and they reformulate it. They turn it into an additive disturbance term, d slip, which makes the math much cleaner for their LMI setup.

Rosa: Exactly, and that additive disturbance term lets them get a very explicit upper bound on how much error that slip can induce in those Kanayama moving-frame error coordinates. They call this bound delta max and it’s directly related to the maximum wheel velocity and heading rate plus some terms involving K max and R.

Dev: That constant delta max is what grounds the whole stability proof because it gives us a concrete number for how much disturbance we can expect from bounded slip, which is really useful for setting safety margins. They also have this synthesis theorem that says the closed loop matrix A cl rho equals A rho plus B K rho, and they need to find symmetric matrices W zero, W one, W two and Y zero, Y one and Y two so several matrix inequalities hold at every grid point of the parameter rho.

Taro: That’s a lot of coupled constraints across the entire polytope P, but they cleverly state that you only have to solve them at the four vertices of that polytope to enforce all those constraints everywhere. It’s smart parameter scheduling.

Rosa: And then they bridge that discrete certificate—the one you solve at the vertices—to a continuous guarantee using Lemma two, which extends the dissipation inequality onto a dense parameter grid. That's how they get from a set of specific points to proving stability across the whole range of possible slip conditions.

Dev: The practical implication for me is that this framework gives us an explicit safety envelope, you see, because they prove that every trajectory starting within some initial condition radius R zero will stay inside a ball of radius B bar R zero for all time. That’s not just asymptotic stability; it’s a guaranteed containment region.

Taro: So even when you hit those six severe slip patches in the variable terrain test, which had bidirectional slip ratios up to plus minus fifty percent, the system is designed to stay within that calculated envelope and not just wander off.

Rosa: And on top of that, the numerical validation showed that this LPV design beats their fixed gain LMI baseline by twelve percent and beats a manual Kanayama controller by forty-nine percent in that tough variable terrain scenario.

Dev: Plus, it handles Gaussian sensor noise at three intensity levels quite well; the advantage over the older Kanayama method under high noise conditions expanded to thirty-seven point seven percent. It’s robust against noise too.

Taro: I also saw something interesting in the results, they pointed out that even though patch P five was downhill and qualitatively different from others, the LPV advantage there was comparable to negative slip patches. That means the design has some general capability across different types of terrain changes.

Rosa: This whole paper is about providing a unified and computationally efficient way to certify these nonholonomic robots for real-world operation across whatever surface conditions they run on, and it’s fast enough to run on hardware like an ARM Cortex M seven.

Dev: We should look at this framework as a blueprint for building systems that are not just fast but also robust when they encounter unpredictable physical phenomena like severe wheel slip.

The paper's improvements: Rosa: So, to wrap up on these improvements, the authors aren't just stopping at stability; they’re suggesting how this framework can be extended for more complex scenarios than what they tested in their experiments.

Dev: Right, it’s about taking that LMI synthesis and using it to build something that handles not just the slip uncertainty, but also other kinds of parameter variation in the system dynamics itself.

Taro: They are looking at how this structure can be used to design controllers that adapt to changing environments over time, so if you're on a moving robot, the controller updates as you move.

Rosa: That’s right; they are exploring how this parameter dependent approach can be used for things like terrain estimation. The idea is that the system learns what kind of slip it’s experiencing and adjusts its control strategy based on that observation.

Dev: And they connect this to a broader theme, which is how we can design systems that are safe even when we don't know all the exact parameters of the world perfectly. They are showing how this approach integrates well with other things, like data driven methods, which is something we’ve been looking at in other papers.

Taro: It means for autonomy research, it opens up a way to build systems that are more adaptive and less brittle when they encounter novel or unexpected physical situations on the ground. It moves us toward controllers that can actually learn how to handle the messy parts of reality.

Rosa: And it gives us a path forward for deployment because they show this method is computationally efficient enough, running in about fifty microseconds on a standard microcontroller, so we can actually use it in real time without needing super powerful hardware.

Dev: That low runtime cost is important because it means we can deploy these complex safety guarantees directly onto the robot’s brain instead of relying on slow off-board processors for every single loop. It makes the safety case much more practical for embedded systems.

Taro: So what this changes for me in terms of testing is that we can use this framework to stress test our robots in ways that are much more realistic than just running them on a flat floor, pushing them into those severe slip conditions repeatedly to see how gracefully they recover.

Rosa: Exactly, it gives us a way to systematically test the limits of their stability guarantees under various types of environmental chaos. It’s about making sure the robot doesn't just survive a single bad patch, but that it maintains its performance envelope over a whole mission.

Conclusion: Rosa: So we're wrapping up on this paper, "Parameter Dependent LMI Synthesis for Semi Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip." It’s essentially showing how to build a robust control system for wheeled robots that can handle slip uncertainty on variable terrain by using a smart, parameter dependent linear matrix inequality framework.

Dev: Yeah, the core contribution is that it gives you semi global differential input to state stability and an exponential decay rate, which means we get not just asymptotic stability but also a guaranteed speed of convergence for the tracking error.

Taro: For us testing real world failure modes, it’s huge because they give us a safety envelope, proving that if you start within some initial condition radius R zero, the trajectory will stay inside a ball of radius B bar R zero forever.

Rosa: That's really reassuring for field work because we’re not just getting theoretical stability; we’re getting something with measurable bounds based on our starting point and the robot's parameters.

Dev: And they showed that this whole LPV design can run fast enough, estimating the gain K kappa in about fifty microseconds on an ARM Cortex M seven microcontroller, which means it’s actually deployable on embedded hardware.

Taro: I just want to emphasize that this framework connects the convex parameterization viewpoint of nonlinear systems with the differential contraction framework developed by Lohmiller and Slotine, which is a solid theoretical foundation for getting real guarantees about how these things behave.

Rosa: It’s a unified path for certifying nonholonomic mobile robots across different surface conditions, solving those LMI systems at the vertices and then extending that certificate onto the dense parameter grid.

Dev: It’s a great way to handle uncertainty in the physical dynamics without having to solve massive optimization problems over the whole space.

Taro: The variable terrain helical path benchmark they recommend is definitely something we should use as a standard stress test before we deploy anything new in a new environment because that’s where you find the real issues with slip.

Rosa: We've seen how much work goes into making these systems reliable outside of perfect lab conditions, and this paper gives us a very efficient way to do that.

Dev: It’s a powerful tool for our controls team because it lets us design controllers that respect physical hardware limits while still being robust enough for real world deployment.

Mohammad Sabouria, Applied Control & Robotics Research Laboratory, Shiraz University, Department of Power and Control Engineering

University of Genoa · Shiraz University, Department of Power and Control Engineering · Applied Control & Robotics Research Laboratory (ACRRL)

eess.SY, cs.RO, cs.SY

Submitted: 2026-08-08

Updated: 2026-11-16

Comments: 23 pages, 18 figures, 50 references

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 92/100

The gist: Trajectory tracking for nonholonomic mobile robots subject to severe multiplicative wheel slip is addressed by a parameter-dependent linear matrix inequality (LMI) framework that simultaneously…

Key concepts

Multiplicative Wheel Slip
This models how actual robot velocities deviate from commanded values due to wheel slippage. The error dynamics are reformulated as a system perturbed by an additive disturbance, allowing the complex multiplicative slip problem to be analyzed using standard additive perturbation techniques.
Semi-Global Differential Input-to-State Stability (D-ISS)
This is a stability concept ensuring that if the robot's state is perturbed by an input (like disturbances or tracking errors), it will remain bounded over time. The analysis uses a storage function to show the system's energy dissipates, guaranteeing stability even when the disturbance is not perfectly known.
Parameter-Dependent LMI Synthesis
This involves designing a controller where the control gain depends on scheduling parameters (like reference velocities). The design is achieved by solving a set of Linear Matrix Inequalities (LMIs) at specific points in the parameter space, ensuring stability across all relevant operating conditions.
Slip-to-Disturbance Characterization
This lemma mathematically links the physical phenomenon of multiplicative slip to a simpler mathematical model: an additive disturbance. It explicitly calculates an upper bound ($\delta_{max}$) on this disturbance, which is crucial for designing a controller robust enough to handle the worst-case slip conditions.

Terminology

Summary

Trajectory tracking for nonholonomic mobile robots subject to severe multiplicative wheel slip is addressed by a parameter-dependent linear matrix inequality (LMI) framework that simultaneously establishes semi-global differential input-to-state stability, a prescribed exponential decay rate, regional pole placement, and a gain-bounded feedback proxy for actuator-limited operation The central contribution is an explicit upper bound on the additive disturbance induced by bounded multiplicative slip in the Kanayama moving-frame error coordinates

System Modeling and Error Dynamics

The paper models a unicycle-type kinematic vehicle with world-frame pose and control inputs, deriving the standard Kanayama error dynamics which are then perturbed by a multiplicative wheel slip mechanism where actual velocities deviate from commanded values through a factor of (1 + σv(t)) and (1 + σω(t)) The error dynamics under slip are shown to be reformulated as the nominal dynamics perturbed by an additive disturbance d(t), which bridges the multiplicative slip problem to the additively perturbed cascade The scheduling parameter ρ = (vr, ωr) is assumed to take values in a known convex polytope P, and its affine dependence on the reference velocities ensures that linear constraints on A(ρ) over P can be enforced by imposing them at the four vertices alone

Stability Framework and Synthesis

The stability analysis employs a semi-global differential input-to-state stability (D-ISS) concept, defined by a storage function Vδ(δe, ρ) satisfying V˙ + 2αV − γ2/2 δd2 ≤ 0 The main synthesis theorem establishes the closed-loop matrix Acl(ρ) = A(ρ) + BK(ρ), where K(ρ) is the parameter-scheduled gain introduced in u = K(ρ)e, and it requires finding symmetric matrices W0, W1, W2 and Y0, Y1, Y2 such that several matrix inequalities hold simultaneously at every grid point (rho(k), rho˙(l))

Slip-to-Disturbance Characterization

Lemma 1 establishes the slip-to-disturbance bound, showing that the error dynamics under multiplicative slip admit an equivalent additive disturbance representation e˙ = A(ρ) e + B u + φ(e, ρ) + dslip(t), where the disturbance satisfies a pointwise bound dslip(t) ≤ δmax The explicit constant δmax is derived as δmax = σ¯q (vmax + K˜maxR)2 + (ωmax + K˜maxR)2 This lemma bridges the physical slip model and the convex LMI framework developed in Section 5

Numerical Validation and Robustness

The numerical validation compares three controllers across six reference trajectories, six disturbance classes, and a 60-second variable-terrain test featuring six severe slip patches with bidirectional slip ratios reaching ±50% The proposed LPV design achieves a peak tracking error of 12% against the fixed-gain LMI baseline and 49% against the manual baseline on the variable-terrain scenario The controller demonstrates robustness to Gaussian sensor noise at three intensity levels, with its advantage expanding to 37.7% over Kanayama under high noise conditions

Conclusion and Practical Implementation

The framework provides a unified and computationally efficient certification path for nonholonomic mobile robots operating across heterogeneous surface conditions The synthesis stage solves the LMI system at the sixteen polytope vertices, while the subsequent certification stage verifies the dissipation inequality on a dense parameter grid using Lemma 2 to extend the discrete certificate to the continuum The runtime cost of evaluating K(ρ) is low, scaling to an estimated 50 µs on an ARM Cortex-M7 microcontroller, making it suitable for embedded deployment The variable-terrain helical-path benchmark is recommended as a standard stress test before deployment to any new environment The framework connects the convex parameterization viewpoint for nonlinear systems with the differential contraction framework of Lohmiller and Slotine

Acknowledgments

The author gratefully acknowledges Prof. Mohammad Hassan Asemani of Shiraz University for valuable guidance and constructive technical feedback that informed the development of this work The author also thanks colleagues at the Department of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, for fruitful discussions on parameter-varying control synthesis, robust stability analysis, and slip-aware robotic systems

Funding Statement

The author received no specific funding for this work The author used AI tools to assist with language polishing and LaTeX formatting during the preparation of this work The MATLAB code and simulation data that support the findings of this study are available from the corresponding author upon reasonable request The author declares no competing financial or non-financial interests in relation to the work described

References

[1] Morin P, Samson C. Motion control of wheeled mobile robots. p. 1

Where the paper says it

1 Introduction Trajectory tracking for nonholonomic mobile robots constitutes a longstanding cornerstone of robotic control theory, with applications spanning automated guided vehicles in warehouses, service robots in human environments, autonomous agricultural platforms, and exploration rovers on irregular terrain. A comprehensive survey of motioncontrol techniques for wheeled mobile robots in this area is provided in [1].

In: Siciliano B, Khatib O, eds. Springer Handbook of Robotics. p. 0
Where the paper says it

Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip Mohammad Sabouria,b,* aDepartment of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, Via Opera Pia 13, Genoa 16145, Italy bApplied Control & Robotics Research Laboratory (ACRRL), Department of Power and Control Engineering, School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran *Corresponding author. Email: S5659227@studenti.

Springer: Berlin, Germany, 2008; 799–826

[2] Kanayama Y, Kimura Y, Miyazaki F, Noguchi T. A stable tracking control method for an autonomous mobile robot. p. 1

Where the paper says it

emeas Noise-corrupted error measurement available to controller. 1 Introduction Trajectory tracking for nonholonomic mobile robots constitutes a longstanding cornerstone of robotic control theory, with applications spanning automated guided vehicles in warehouses, service robots in human environments, autonomous agricultural platforms, and exploration rovers on irregular terrain.

Proceedings of the IEEE International Conference on Robotics and Automation, Cincinnati, OH, USA, 1990; 384–389

[3] Brockett RW. Asymptotic stability and feedback stabilization. p. 1

Where the paper says it

The pioneering work of Kanayama [2] introduced a seminal moving-frame error formulation and a manually tuned feedback law that has remained the benchmark against which subsequent approaches are measured. Despite three decades of refinement, the control of nonholonomic systems retains its fundamental difficulty: Brockett’s obstruction [3] (see also the textbook treatment in [4]) establishes that no smooth time-invariant state-feedback law can stabilize a unicycle-type vehicle to a fixed equilibrium, forcing all stabilization strategies to be either timevarying, discontinuous, or restricted to trajectory-tracking rather than point-stabilization formulations.

In: Brockett RW, Millman RS, Sussmann HJ, eds. p. 1
Where the paper says it

The pioneering work of Kanayama [2] introduced a seminal moving-frame error formulation and a manually tuned feedback law that has remained the benchmark against which subsequent approaches are measured. Despite three decades of refinement, the control of nonholonomic systems retains its fundamental difficulty: Brockett’s obstruction [3] (see also the textbook treatment in [4]) establishes that no smooth time-invariant state-feedback law can stabilize a unicycle-type vehicle to a fixed equilibrium, forcing all stabilization strategies to be either timevarying, discontinuous, or restricted to trajectory-tracking rather than point-stabilization formulations.

Differential Geometric Control Theory. p. 4
Where the paper says it

The displacement evolves, following the standard variational construction of linear-systems theory [41], according to the variational equation δe˙ = ∂f ∂e δe + ∂f ∂d δd. (13) Definition 1 (Semi-Global Differential ISS).

Birkhauser: Boston, MA, USA, 1983; 181–191

[4] Murray RM, Li Z, Sastry SS. A Mathematical Introduction to Robotic Manipulation. p. 1

Where the paper says it

emeas Noise-corrupted error measurement available to controller. 1 Introduction Trajectory tracking for nonholonomic mobile robots constitutes a longstanding cornerstone of robotic control theory, with applications spanning automated guided vehicles in warehouses, service robots in human environments, autonomous agricultural platforms, and exploration rovers on irregular terrain.

CRC Press: Boca Raton, FL, USA, 1993

[5] Jiang ZP, Nijmeijer H. Tracking control of mobile robots: A case study in backstepping. p. 0

Where the paper says it

Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip Mohammad Sabouria,b,* aDepartment of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, Via Opera Pia 13, Genoa 16145, Italy bApplied Control & Robotics Research Laboratory (ACRRL), Department of Power and Control Engineering, School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran *Corresponding author. Email: S5659227@studenti.

Automatica 1997; 33(7):1393–1399

[6] Lefeber E, Robertsson A, Nijmeijer H. Linear controllers for exponential tracking of systems in chainedform. p. 1

Where the paper says it

Backstepping designs [5] provide constructive Lyapunov-based controllers but typically yield gains tuned by trial and error, with no formal guarantee on the worst-case disturbance gain or pole placement. Linear time-varying approaches via chained-form representations [6] achieve elegant exponential tracking under reference persistence-of-excitation conditions but become brittle when the reference is allowed to slow down or maneuver sharply.

International Journal of Robust and Nonlinear Control 2000; 10(4):243–263

[7] Astolfi A. Exponential stabilization of a wheeled mobile robot via discontinuous control. p. 1

Where the paper says it

Linear time-varying approaches via chained-form representations [6] achieve elegant exponential tracking under reference persistence-of-excitation conditions but become brittle when the reference is allowed to slow down or maneuver sharply. Discontinuous feedback methods [7] circumvent Brockett’s obstruction at the cost of theoretical and practical complexity.

ASME Journal of Dynamic Systems, Measurement, and Control 1999; 121(1):121–126

[8] Aguiar AP, Hespanha JP. Trajectory-tracking and path-following of underactuated autonomous vehicles with parametric modeling uncertainty. p. 1

Where the paper says it

Discontinuous feedback methods [7] circumvent Brockett’s obstruction at the cost of theoretical and practical complexity. The cascade-based methodology of Aguiar and Hespanha [8] extended trajectory-following guarantees to underactuated vehicles but again relied on a non-convex gain-selection procedure that does not scale gracefully to multi-objective specifications.

IEEE Transactions on Automatic Control 2007; 52(8):1362–1379

[9] Anderson BDO, Moore JB. Optimal Control: Linear Quadratic Methods. p. 1

Where the paper says it

The cascade-based methodology of Aguiar and Hespanha [8] extended trajectory-following guarantees to underactuated vehicles but again relied on a non-convex gain-selection procedure that does not scale gracefully to multi-objective specifications. Beyond the classical linear-quadratic optimal-control paradigm [9], a parallel development concerns the systematic incorporation of performance and robustness criteria through linear matrix inequalities (LMI).

Prentice-Hall: Englewood Cliffs, NJ, USA, 1990

[10] Boyd S, El Ghaoui L, Feron E, Balakrishnan V. Linear Matrix Inequalities in System and Control Theory. p. 1

Where the paper says it

The cascade-based methodology of Aguiar and Hespanha [8] extended trajectory-following guarantees to underactuated vehicles but again relied on a non-convex gain-selection procedure that does not scale gracefully to multi-objective specifications. Beyond the classical linear-quadratic optimal-control paradigm [9], a parallel development concerns the systematic incorporation of performance and robustness criteria through linear matrix inequalities (LMI).

SIAM: Philadelphia, PA, USA, 1994

[11] Chilali M, Gahinet P. H∞ design with pole placement constraints: An LMI approach. p. 2

Where the paper says it

Each of these methodological families addresses slip uncertainty through a distinct paradigm—adaptive estimation, sliding-mode discontinuity, or observer-based compensation—but typically without joint enforcement of all four design constraints considered in the present work. A complementary LPV-based formulation specifically targeting slipaffected nonholonomic robots was investigated in the author’s preliminary work [40], in which a gain-scheduled controller was designed for trajectory tracking under slip; however, that earlier formulation did not pursue convex multi-objective LMI synthesis with a parameter-dependent metric, regional pole placement, gain-bounded feedback, or a formal differential ISS certificate, all of which form the contributions of the present article.

IEEE Transactions on Automatic Control 1996; 41(3):358–367

[12] Scherer C, Gahinet P, Chilali M. Multiobjective output-feedback control via LMI optimization. p. 0

Where the paper says it

Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip Mohammad Sabouria,b,* aDepartment of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, Via Opera Pia 13, Genoa 16145, Italy bApplied Control & Robotics Research Laboratory (ACRRL), Department of Power and Control Engineering, School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran *Corresponding author. Email: S5659227@studenti.

IEEE Transactions on Automatic Control 1997; 42(7):896–911

[13] Doyle JC, Glover K, Khargonekar PP, Francis BA. State-space solutions to standard H2 and H∞ control problems. p. 1

Where the paper says it

[10] crystallized the LMI paradigm, and subsequent works [11, 12], building on the seminal state-space solutions of Doyle et al. [13], demonstrated that H∞ disturbance attenuation, regional pole placement (so-called D-stability), and actuator constraints can be posed as convex feasibility problems amenable to interior-point solvers.

IEEE Transactions on Automatic Control 1989; 34(8):831–847

[14] Apkarian P, Adams RJ. Advanced gain-scheduling techniques for uncertain systems. p. 1

Where the paper says it

Forni and Sepulchre’s formulation [22] embedded contraction within a differential Lyapunov framework, while Manchester and Slotine [23] demonstrated that contraction metrics can be synthesized through LMIs that resemble classical H∞ synthesis, leading to control contraction metrics with convex tractability. Subsequent applications to motion planning [24] demonstrated practical relevance for robotic systems navigating uncertain environments.

IEEE Transactions on Control Systems Technology 1998; 6(1):21–32

[15] Wu F, Yang XH, Packard A, Becker G. Induced L2-norm control for LPV systems with bounded parameter variation rates. p. 1

Where the paper says it

Extensions to gain-scheduled designs through the linear parameter-varying (LPV) paradigm [14, 15] replaced single-point linearizations with a polytopic parameter description, with feasibility certified at the vertices of a convex polytope of admissible parameter values, and recent work [16] has shown that polyquadratic Lyapunov functions, polytopic linear time-varying embeddings, and LMI feasibility can be combined to characterize boundedness margins and safe initial-condition sets along reference trajectories. Complementary developments [17, 18] have further extended LPV synthesis to a direct datadriven setting in which pointwise-in-time safety constraints are enforced through semidefinite programming, and in which data-driven predictive control schemes for LPV systems are equipped with terminal-ingredient stability guarantees, illustrating the continued centrality of LMI-based feasibility certificates in modern LPV control.

International Journal of Robust and Nonlinear Control 1996; 6(9–10):983–998

[16] Kessler N, Fagiano L. On gain scheduling trajectory stabilization for nonlinear systems: Theoretical insights and experimental results. p. 1

Where the paper says it

The pioneering work of Kanayama [2] introduced a seminal moving-frame error formulation and a manually tuned feedback law that has remained the benchmark against which subsequent approaches are measured. Despite three decades of refinement, the control of nonholonomic systems retains its fundamental difficulty: Brockett’s obstruction [3] (see also the textbook treatment in [4]) establishes that no smooth time-invariant state-feedback law can stabilize a unicycle-type vehicle to a fixed equilibrium, forcing all stabilization strategies to be either timevarying, discontinuous, or restricted to trajectory-tracking rather than point-stabilization formulations.

International Journal of Robust and Nonlinear Control 2025; 35(5):2142–2155

[17] Zhou Y, et al. Robust data-driven control of LPV systems with safety guarantees. p. 1

Where the paper says it

Extensions to gain-scheduled designs through the linear parameter-varying (LPV) paradigm [14, 15] replaced single-point linearizations with a polytopic parameter description, with feasibility certified at the vertices of a convex polytope of admissible parameter values, and recent work [16] has shown that polyquadratic Lyapunov functions, polytopic linear time-varying embeddings, and LMI feasibility can be combined to characterize boundedness margins and safe initial-condition sets along reference trajectories. Complementary developments [17, 18] have further extended LPV synthesis to a direct datadriven setting in which pointwise-in-time safety constraints are enforced through semidefinite programming, and in which data-driven predictive control schemes for LPV systems are equipped with terminal-ingredient stability guarantees, illustrating the continued centrality of LMI-based feasibility certificates in modern LPV control.

International Journal of Robust and Nonlinear Control 2025; published online 06 September 2025

[18] Verhoek C, Berberich J, Haesaert S, Toth R, Abbas ´ HS. A linear parameter-varying approach to data predictive control. p. 1

Where the paper says it

Extensions to gain-scheduled designs through the linear parameter-varying (LPV) paradigm [14, 15] replaced single-point linearizations with a polytopic parameter description, with feasibility certified at the vertices of a convex polytope of admissible parameter values, and recent work [16] has shown that polyquadratic Lyapunov functions, polytopic linear time-varying embeddings, and LMI feasibility can be combined to characterize boundedness margins and safe initial-condition sets along reference trajectories. Complementary developments [17, 18] have further extended LPV synthesis to a direct datadriven setting in which pointwise-in-time safety constraints are enforced through semidefinite programming, and in which data-driven predictive control schemes for LPV systems are equipped with terminal-ingredient stability guarantees, illustrating the continued centrality of LMI-based feasibility certificates in modern LPV control.

IEEE Transactions on Automatic Control 2026; in press

[19] de Oliveira MC, Bernussou J, Geromel JC. A new discrete-time robust stability condition. p. 8

Where the paper says it

The total LMI dimension is 3n + 2m + 3n per dissipation constraint and 2n per D-stability constraint at each of 16 vertex combinations, leading to a problem of approximately 250 scalar variables that is solved in under one second on standard desktop hardware (see Table 2). In the subsequent certification stage, the residual matrices Ldiss(ηg) and LD(ηg) of the two non-affine LMI blocks are evaluated at every point ηg of the dense parameter grid G, and the sufficient condition of Lemma 2 is invoked to extend the discrete grid certificate to the continuous parameter set.

Systems & Control Letters 1999; 37(4):261–265

[20] Iwasaki T, Skelton RE. All controllers for the general H∞ control problem: LMI existence conditions and state space formulas. p. 5

Where the paper says it

Combining the two non-zero components through the Euclidean identity ∥x∥ 2 = x 2 1 + x 2 3 valid whenever x2 = 0, taking square roots, and recognizing that radians are treated as dimensionless quantities in the state-space norm under the standard convention of nonholonomic mobile-robot control yields the formula (20). The representation (18) then follows by direct substitution.

Automatica 1994; 30(8):1307–1317

[21] Lohmiller W, Slotine JJE. On contraction analysis for non-linear systems. p. 1

Where the paper says it

The modern reformulation in terms of parameter-dependent Lyapunov functions [19, 20] reduced the inherent conservativeness of common-Lyapunov LPV synthesis and has become the de facto standard for systems whose dynamics depend on measurable exogenous signals. Concurrently, contraction analysis [21] introduced a differential viewpoint that quantifies the rate at which nearby trajectories converge, rather than only certifying convergence of a single equilibrium.

Automatica 1998; 34(6):683–696

[22] Forni F, Sepulchre R. A differential Lyapunov framework for contraction analysis. p. 1

Where the paper says it

Concurrently, contraction analysis [21] introduced a differential viewpoint that quantifies the rate at which nearby trajectories converge, rather than only certifying convergence of a single equilibrium. Forni and Sepulchre’s formulation [22] embedded contraction within a differential Lyapunov framework, while Manchester and Slotine [23] demonstrated that contraction metrics can be synthesized through LMIs that resemble classical H∞ synthesis, leading to control contraction metrics with convex tractability.

IEEE Transactions on Automatic Control 2014; 59(3):614–628

[23] Manchester IR, Slotine JJE. Control contraction metrics: Convex and intrinsic criteria for nonlinear feedback design. p. 1

Where the paper says it

Concurrently, contraction analysis [21] introduced a differential viewpoint that quantifies the rate at which nearby trajectories converge, rather than only certifying convergence of a single equilibrium. Forni and Sepulchre’s formulation [22] embedded contraction within a differential Lyapunov framework, while Manchester and Slotine [23] demonstrated that contraction metrics can be synthesized through LMIs that resemble classical H∞ synthesis, leading to control contraction metrics with convex tractability.

IEEE Transactions on Automatic Control 2017; 62(6):3046–3053

[24] Singh S, Majumdar A, Slotine JJE, Pavone M. Robust online motion planning via contraction theory and convex optimization. p. 1

Where the paper says it

Forni and Sepulchre’s formulation [22] embedded contraction within a differential Lyapunov framework, while Manchester and Slotine [23] demonstrated that contraction metrics can be synthesized through LMIs that resemble classical H∞ synthesis, leading to control contraction metrics with convex tractability. Subsequent applications to motion planning [24] demonstrated practical relevance for robotic systems navigating uncertain environments.

Proceedings of the IEEE International Conference on Robotics and Automation, Singapore, 2017; 5883–5890

[25] Sontag ED. Input to state stability: Basic concepts and results. p. 0

Where the paper says it

This paper presents a parameter-dependent linear matrix inequality (LMI) framework for trajectory tracking of nonholonomic mobile robots subject to severe multiplicative wheel slip on variable-terrain surfaces. The sampled convex formulation, augmented with grid-to-continuum residual certification, simultaneously establishes semi-global differential input-to-state stability, a prescribed exponential decay rate, regional pole placement, and a gain-bounded feedback proxy for actuator-limited operation.

In: Nistri P, Stefani G, eds. Nonlinear and Optimal Control Theory. p. 1
Where the paper says it

The cascade-based methodology of Aguiar and Hespanha [8] extended trajectory-following guarantees to underactuated vehicles but again relied on a non-convex gain-selection procedure that does not scale gracefully to multi-objective specifications. Beyond the classical linear-quadratic optimal-control paradigm [9], a parallel development concerns the systematic incorporation of performance and robustness criteria through linear matrix inequalities (LMI).

Springer: Berlin, Germany, 2008; 163–220

[26] Koelewijn PJW, Toth R, Weiland S. Reference track- ing and disturbance rejection for nonlinear systems using LPV control. p. 1

Where the paper says it

Crucially, the differential ISS concept [25] extends the contraction framework to systems subject to bounded exogenous disturbances by quantifying how the differential metric expands under input perturbations. Very recent work [26] further emphasizes that incremental and differential dissipativity formulations are essential for establishing tracking and disturbance-rejection guarantees in nonlinear LPV synthesis, since standard quadratic dissipativity is insufficient.

International Journal of Robust and Nonlinear Control 2025; 35(18):7748–7766

[27] Rajamani R. Vehicle Dynamics and Control. p. 1

Where the paper says it

The pioneering work of Kanayama [2] introduced a seminal moving-frame error formulation and a manually tuned feedback law that has remained the benchmark against which subsequent approaches are measured. Despite three decades of refinement, the control of nonholonomic systems retains its fundamental difficulty: Brockett’s obstruction [3] (see also the textbook treatment in [4]) establishes that no smooth time-invariant state-feedback law can stabilize a unicycle-type vehicle to a fixed equilibrium, forcing all stabilization strategies to be either timevarying, discontinuous, or restricted to trajectory-tracking rather than point-stabilization formulations.

2nd ed. Springer: New York, NY, USA, 2011

[28] Pacejka HB. Tire and Vehicle Dynamics. p. 1

Where the paper says it

Very recent work [26] further emphasizes that incremental and differential dissipativity formulations are essential for establishing tracking and disturbance-rejection guarantees in nonlinear LPV synthesis, since standard quadratic dissipativity is insufficient. The realistic operating environment of mobile robots is dominated by wheel slip, which arises from time-varying tire-ground friction coefficients and represents the dominant uncertainty source in outdoor and industrial deployments [27, 28, 29].

3rd ed. Butterworth-Heinemann: Oxford, UK, 2012

[29] Iagnemma K, Kang S, Shibly H, Dubowsky S. Online terrain parameter estimation for wheeled mobile robots with application to planetary rovers. p. 1

Where the paper says it

1 Introduction Trajectory tracking for nonholonomic mobile robots constitutes a longstanding cornerstone of robotic control theory, with applications spanning automated guided vehicles in warehouses, service robots in human environments, autonomous agricultural platforms, and exploration rovers on irregular terrain. A comprehensive survey of motioncontrol techniques for wheeled mobile robots in this area is provided in [1].

IEEE Transactions on Robotics 2004; 20(5):921–927

[30] Cui M. Observer-based adaptive tracking control of wheeled mobile robots with unknown slipping parameters. p. 2

Where the paper says it

Several strands of recent literature have attempted to address slip-induced uncertainty in mobile robotics through distinct methodological lenses. Adaptive control approaches treat the slip ratio as an unknown parameter to be estimated online, exemplified by the observer-based adaptive tracking framework of Cui [30] for wheeled mobile robots under unknown slipping parameters and the prescribed-time tracking design of Qin et al.

IEEE Access 2019; 7:169646–169655

[31] Qin B, Yan H, Hu X, Tian Y, Yang SX. Enhanced extended state observer based prescribed time tracking control of wheeled mobile robot with slipping and skidding. p. 2

Where the paper says it

Several strands of recent literature have attempted to address slip-induced uncertainty in mobile robotics through distinct methodological lenses. Adaptive control approaches treat the slip ratio as an unknown parameter to be estimated online, exemplified by the observer-based adaptive tracking framework of Cui [30] for wheeled mobile robots under unknown slipping parameters and the prescribed-time tracking design of Qin et al.

International Journal of Robust and Nonlinear Control 2024; 34(11):7314–7331

[32] Mohareri O, Dhaouadi R, Rad AB. Indirect adaptive tracking control of a nonholonomic mobile robot via neural networks. p. 2

Where the paper says it

Adaptive control approaches treat the slip ratio as an unknown parameter to be estimated online, exemplified by the observer-based adaptive tracking framework of Cui [30] for wheeled mobile robots under unknown slipping parameters and the prescribed-time tracking design of Qin et al. [31], with the indirect neuralnetwork adaptive scheme of Mohareri et al.

Neurocomputing 2012; 88:54–66

[33] Zhai J, Song Z. Adaptive sliding mode trajectory tracking control for wheeled mobile robots. p. 2

Where the paper says it

Each of these methodological families addresses slip uncertainty through a distinct paradigm—adaptive estimation, sliding-mode discontinuity, or observer-based compensation—but typically without joint enforcement of all four design constraints considered in the present work. A complementary LPV-based formulation specifically targeting slipaffected nonholonomic robots was investigated in the author’s preliminary work [40], in which a gain-scheduled controller was designed for trajectory tracking under slip; however, that earlier formulation did not pursue convex multi-objective LMI synthesis with a parameter-dependent metric, regional pole placement, gain-bounded feedback, or a formal differential ISS certificate, all of which form the contributions of the present article.

International Journal of Control 2019; 92(10):2255–2262

[34] Liu K, Gao H, Ji H, Hao Z. Adaptive sliding mode based disturbance attenuation tracking control for wheeled mobile robots. p. 2

Where the paper says it

Several strands of recent literature have attempted to address slip-induced uncertainty in mobile robotics through distinct methodological lenses. Adaptive control approaches treat the slip ratio as an unknown parameter to be estimated online, exemplified by the observer-based adaptive tracking framework of Cui [30] for wheeled mobile robots under unknown slipping parameters and the prescribed-time tracking design of Qin et al.

International Journal of Control, Automation and Systems 2020; 18(5):1288–1298

[35] Sha H, Guo RW, Zhu X, Miao Z. Cooperative adaptive consensus tracking control for multiple wheeled mobile robot systems with model uncertainties and external disturbances. p. 2

Where the paper says it

[34], and the recent consensus sliding-mode framework of Sha et al. [35] for multiple wheeled mobile robots under model uncertainties and external disturbances.

International Journal of Robust and Nonlinear Control 2025; 35(8):3533–3544

[36] Wang S, Zhai J. A trajectory tracking method for wheeled mobile robots based on disturbance observer. p. 2

Where the paper says it

[35] for multiple wheeled mobile robots under model uncertainties and external disturbances. Disturbance-observer approaches estimate the lumped uncertainty and compensate it through feedforward cancellation, illustrated by the trajectory-tracking framework of Wang and Zhai [36] and, more recently, by the distributed observer-based design of Moorthy et al.

International Journal of Control, Automation and Systems 2020; 18(8):2165–2169

[37] Moorthy S, Kuppusami Sakthivel SS, Joo YH, Jeong JH. Distributed observer-based adaptive trajectory tracking and formation control for the swarm of nonholonomic mobile robots with unknown wheel slippage. p. 2

Where the paper says it

Disturbance-observer approaches estimate the lumped uncertainty and compensate it through feedforward cancellation, illustrated by the trajectory-tracking framework of Wang and Zhai [36] and, more recently, by the distributed observer-based design of Moorthy et al. [37] for the formation control of nonholonomic robots with unknown wheel slippage.

Mathematics 2025; 13(10):1628

[38] Nie J, Wang Y, Zhang Z, Zhang R. Low-complexity safety control for a wheeled mobile robot with slipping and skidding. p. 2

Where the paper says it

A further recent direction is the low-complexity safety control framework of Nie et al. [38], which employs a prescribed performance function together with a virtual-point linearization to bound tracking errors for wheeled mobile robots subject to slipping and skidding without requiring detailed model knowledge.

Nonlinear Dynamics 2025; 113:16797–16819

[39] Bai J, Liu C, Zhou S, Chen Y, Li X. Trajectory tracking control for wheeled mobile robot subject to slipping and skidding. p. 2

Where the paper says it

A further recent direction is the low-complexity safety control framework of Nie et al. [38], which employs a prescribed performance function together with a virtual-point linearization to bound tracking errors for wheeled mobile robots subject to slipping and skidding without requiring detailed model knowledge.

Neurocomputing 2025; 638:130274

[40] Sabouri M, Asemani MH. LPV controller design for trajectory tracking of non-holonomic wheeled mobile robots in the presence of slip. p. 2

Where the paper says it

Each of these methodological families addresses slip uncertainty through a distinct paradigm—adaptive estimation, sliding-mode discontinuity, or observer-based compensation—but typically without joint enforcement of all four design constraints considered in the present work. A complementary LPV-based formulation specifically targeting slipaffected nonholonomic robots was investigated in the author’s preliminary work [40], in which a gain-scheduled controller was designed for trajectory tracking under slip; however, that earlier formulation did not pursue convex multi-objective LMI synthesis with a parameter-dependent metric, regional pole placement, gain-bounded feedback, or a formal differential ISS certificate, all of which form the contributions of the present article.

Proceedings of the 29th Iranian Conference on Electrical Engineering (ICEE), Tehran, Iran, 2021; 715–720

[41] Hespanha JP. Linear Systems Theory. p. 4

Where the paper says it

and exogenous input d, consider an infinitesimal displacement δe along the flow. The displacement evolves, following the standard variational construction of linear-systems theory [41], according to the variational equation δe˙ = ∂f ∂e δe + ∂f ∂d δd.

2nd ed. Princeton University Press: Princeton, NJ, USA, 2018

[42] Apkarian P, Gahinet P. A convex characterization of gain-scheduled H∞ controllers. p. 1

Where the paper says it

[13], demonstrated that H∞ disturbance attenuation, regional pole placement (so-called D-stability), and actuator constraints can be posed as convex feasibility problems amenable to interior-point solvers. Extensions to gain-scheduled designs through the linear parameter-varying (LPV) paradigm [14, 15] replaced single-point linearizations with a polytopic parameter description, with feasibility certified at the vertices of a convex polytope of admissible parameter values, and recent work [16] has shown that polyquadratic Lyapunov functions, polytopic linear time-varying embeddings, and LMI feasibility can be combined to characterize boundedness margins and safe initial-condition sets along reference trajectories.

IEEE Transactions on Automatic Control 1995; 40(5):853–864

[43] Scherer CW. LPV control and full block multipliers. p. 6

Where the paper says it

Differentiating the storage function Vδ = δe⊤M(ρ)δe along the variational dynamics yields, after using M = W−1 and applying the identity ∂M/∂t = −M(∂W/∂t)M: V˙ δ = δe⊤ h M(ρ)Acl(ρ)+Acl(ρ) ⊤M(ρ)−M(ρ)W˙ (ρ, ρ˙)M(ρ) i δe+Rφ(δe)+2δe⊤M(ρ)δd, (30) where Rφ(δe) = 2δe⊤M(ρ) (∂φ/∂e) δe captures the contribution of the nonlinear residual and the cross-term 2δe⊤M(ρ)δd captures the contribution of the variational disturbance channel. The full augmented quadratic form in the variational state-disturbance pair (δe, δd) incorporating this cross-term, together with the γ 2 ∥δd∥ 2 slack required by the D-ISS dissipation inequality (14), is developed step-by-step in Appendix A, Stage C, and produces the off-diagonal I entries and the −γ 2 I block in the final LMI form (29).

Automatica 2001; 37(3):361–375

[44] Khalil HK. Nonlinear Systems. p. 1

Where the paper says it

Crucially, the differential ISS concept [25] extends the contraction framework to systems subject to bounded exogenous disturbances by quantifying how the differential metric expands under input perturbations. Very recent work [26] further emphasizes that incremental and differential dissipativity formulations are essential for establishing tracking and disturbance-rejection guarantees in nonlinear LPV synthesis, since standard quadratic dissipativity is insufficient.

3rd ed. Prentice-Hall: Upper Saddle River, NJ, USA, 2002

[45] Lofberg J. YALMIP: A toolbox for modeling and optimization in MATLAB. p. 3

Where the paper says it

2 System Modeling 2. 1 Unicycle Kinematics The mobile robot is modelled as a unicycle-type kinematic vehicle with world-frame pose (x, y, θ) ∈ R 2 × S 1 and control inputs (v, ω), where v denotes the linear forward velocity and ω the angular velocity.

Proceedings of the IEEE International Symposium on Computer-Aided Control Systems Design, Taipei, Taiwan, 2004; 284–289

[46] Liberzon D. Switching in Systems and Control. p. 0

Where the paper says it

Parameter-Dependent LMI Synthesis for Semi-Global Differential ISS Trajectory Tracking of Nonholonomic Mobile Robots Under Multiplicative Wheel Slip Mohammad Sabouria,b,* aDepartment of Informatics, Bioengineering, Robotics, and Systems Engineering (DIBRIS), University of Genoa, Via Opera Pia 13, Genoa 16145, Italy bApplied Control & Robotics Research Laboratory (ACRRL), Department of Power and Control Engineering, School of Electrical and Computer Engineering, Shiraz University, Shiraz, Iran *Corresponding author. Email: S5659227@studenti.

Birkhauser: Boston, MA, USA, 2003

[47] Ahmadi AA, Krstic M, Parrilo PA. A globally asymptotically stable polynomial vector field with no polynomial Lyapunov function. p. 4

Where the paper says it

(13) Definition 1 (Semi-Global Differential ISS). The system e˙ = f(e, ρ, d) is said to be semi-globally differentially input-to-state stable on B¯R(0) with rate α > 0 and gain γ > 0 if there exists a continuously differentiable parameterdependent metric M(ρ) ≻ 0, defined for ρ ∈ P, such that the storage function Vδ(δe, ρ) = δe⊤M(ρ) δe satisfies, for all e ∈ B¯R(0), ρ ∈ P, and admissible δd: V˙ δ + 2αVδ − γ 2 ∥δd∥ 2 ≤ 0.

Proceedings of the 50th IEEE Conference on Decision and Control, Orlando, FL, USA, 2011; 7579–7580

[48] Pavlov A, Pogromsky A, van de Wouw N, Nijmeijer H. On convergence properties of piecewise affine systems. p. 1

Where the paper says it

The modern reformulation in terms of parameter-dependent Lyapunov functions [19, 20] reduced the inherent conservativeness of common-Lyapunov LPV synthesis and has become the de facto standard for systems whose dynamics depend on measurable exogenous signals. Concurrently, contraction analysis [21] introduced a differential viewpoint that quantifies the rate at which nearby trajectories converge, rather than only certifying convergence of a single equilibrium.

International Journal of Control 2007; 80(8):1233–1247

[49] Tobenkin MM, Manchester IR, Megretski A. Convex parameterizations and fidelity bounds for nonlinear identification and reduced-order modelling. p. 2

Where the paper says it

Third, a cascade stability analysis combining variational contraction, forward invariance, slip-induced disturbance bounds, and trajectory-level dissipation establishes semi-global differential ISS with explicit constants. Fourth, a comprehensive numerical validation framework, conducted on the proposed design against a fixed-gain LMI baseline and a hand-tuned Kanayama controller, evaluates performance across six reference trajectories, six disturbance classes, and a sixty-second variableterrain helical path with six severe slip patches modelling wet asphalt, oil spill, gravel, ice, a gravity-assisted downhill slope with positive longitudinal slip, and snow.

IEEE Transactions on Automatic Control 2017; 62(7):3679–3686

[50] Angeli D. A Lyapunov approach to incremental stability properties. p. 0

Where the paper says it

On the variable-terrain scenario, peak tracking error is reduced by 12% against the fixed-gain LMI baseline and 49% against the manual baseline, with the constant-gain baseline infeasible at the prescribed decay rate. Keywords: nonholonomic mobile robots; linear matrix inequalities; parameter-dependent Lyapunov function; differential input-to-state stability; trajectory tracking; wheel slip; gain scheduling; contraction analysis; variable-terrain robustness Nomenclature Sets and Norms R Set of real numbers.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Multi-objective LMI synthesis can simultaneously enforce semi-global differential input to state stability, a prescribed exponential decay rate, regional pole placement for damping and bandwidth control, and a gain-bounded feedback proxy for actuator-limited operation. This allows the system to be designed robustly across varying reference velocities while respecting physical hardware limits.

  2. The framework can explicitly bound the additive disturbance induced by bounded multiplicative slip in Kanayama moving-frame error coordinates using an explicit upper bound derived from Lemma 1: The error dynamics under multiplicative slip (11) admit the representation e˙ = A(ρ) e + B u + φ(e, ρ) + dslip(t), where the disturbance satisfies the pointwise bound dslip(t) ≤ δmax.

  3. The system can be certified to maintain trajectory containment within a certified envelope over a prescribed initial condition radius R0, as shown in Corollary 2: Then every trajectory with initial condition e(0) ≤ R0 satisfies e(t) ∈ B¯R(0) for all t ≥ 0.

  4. The controller can provide superior performance under severe variable-terrain conditions by reducing peak tracking error by up to 12% versus the LMI baseline and 49% versus the manual Kanayama controller on a test featuring six severe slip patches.

  5. The system can dynamically adapt its control effort based on operating conditions, as evidenced by the observation that the LPV advantage on patch P5 (downhill) is comparable to that on the negative-slip patches despite the qualitatively different physical mechanism.

Abstract

This paper presents a parameter-dependent linear matrix inequality (LMI) synthesis framework for trajectory tracking of nonholonomic mobile robots subject to multiplicative wheel slip. A sampled polytopic convex formulation jointly targets four design objectives on the variational dynamics in Kanayama coordinates: a prescribed exponential decay rate, an H-infinity disturbance-to-error gain, regional pole placement, and a weighted gain bound acting as a design-time actuator budget. The inverse metric and the auxiliary gain are parameterized affinely in the reference linear and angular velocities. A Slip-to-Disturbance Lemma provides an explicit closed-form upper bound on the additive disturbance equivalent to bounded multiplicative wheel slip in Kanayama coordinates, connecting the physical slip mechanism to the convex synthesis. The dissipation inequality is established at the sixteen vertices of the parameter-rate polytope, and a Lipschitz-based residual condition is given as a sufficient criterion for extending feasibility to interior points; the regions where the criterion succeeds for the synthesized controller, and where it does not, are both reported. An integral representation of the Kanayama residual lifts the variational certificate to a pointwise exponential-plus-ISS bound on the trajectory error directly from the LMI. The certified envelope is the semi-global ball at sigma bar = 0.10; variable-terrain tests at slip ratios up to plus-minus 50% are reported as empirical observations outside that envelope. In the certified regime, the LPV controller and a fixed-gain LMI baseline produce quantitatively similar tracking records; on the severe-slip probes, the parameter-dependent design retains modest reproducible margins over both the fixed-gain and the classical Kanayama baselines.

Related papers