Multilayer Dual-polarized Microstrip Antenna Design by Topology Optimization with Enhanced Bandwidth

arXiv:2608.05712 · eess.SY, cs.CE, cs.SY · Submitted 2026-08-06 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: We're looking at the paper: "Multilayer Dual-polarized Microstrip Antenna Design by Topology Optimization with Enhanced Bandwidth".

Dev: Here's the gist of the paper. Dual-polarized (DP) microstrip antennas are utilized in wireless systems for efficient data transmission, and this contribution proposes to design DP microstrip antennas with enhanced bandwidth using a density-based topology optimization approach.

Rosa: Problem Motivation Conventional microstrip antennas typically exhibit a narrow bandwidth which limits their performance in modern systems such as satellite communications, MIMO, and radar systems.

Dev: Traditional approaches to designing DP antennas rely heavily on theoretical analysis and the expertise of design engineers.

Rosa: A common strategy to achieve dual polarizations is to impose structural symmetry on the design

4: –

8: .

Paper summary: Rosa: So, wrapping up the paper "Multilayer Dual-polarized Microstrip Antenna Design by Topology Optimization with Enhanced Bandwidth," the authors show that they achieved two optimized designs operating around five point seven GHz that balance high isolation, which is over forty decibels, with an impedance bandwidth of around ten percent <ref:2608.05712#pg1,Multilayer Dual-polarized Microstrip Antenna Design by Topology Optimization with Enhanced Bandwidth>.

Dev: They also have a second design where they extended the impedance bandwidth to a range from five point five nine GHz to six point zero nine GHz, achieving about nine point nine percent fractional bandwidth while keeping that isolation level between the two ports high at over forty decibels <ref:2608.05712#pg1>.

Taro: The paper suggests that using an optimization algorithm is a supportive tool for designing compact, multiobjective microstrip antennas when you are employing multilayer PCBs. It moves beyond just looking at what works on a single layer and shows how stacking layers can help you achieve better results in terms of bandwidth.

Rosa: Basically, the title highlights that they used topology optimization to enhance the bandwidth of a dual-polarized microstrip antenna by using two layers. It’s about finding that sweet spot where you get good isolation, which is crucial for dual polarization, and wide enough bandwidth for practical use.

Dev: It means that instead of just relying on theoretical analysis or manual design choices, you can use an algorithm to explore the structure of the antenna and find configurations that optimize multiple things at once. The implication is that this method could be useful when designing antennas for systems like MIMO or satellite communications where bandwidth is a real constraint.

Taro: I think what it means for the listener is that complex antenna designs aren't just about knowing all the equations beforehand; you can use an iterative design process to find better physical structures that handle multiple performance requirements simultaneously.

Rosa: That’s right, so this work gives us a method for creating more versatile dual-polarized antennas using topology optimization on multilayer structures. We'll keep an eye on how researchers apply this optimization technique to other antenna types in the future.

Conclusion: Rosa: So, this paper is about taking dual polarized microstrip antennas and using topology optimization on multilayer PCBs to get better bandwidth.

Dev: Yeah, it looks like they focused on how the structure of those layers affects the performance when you optimize for both bandwidth and isolation at the same time.

Taro: It’s not just about stacking things randomly; they are actually designing a specific topology where that dual polarization gets enhanced in terms of how wide its operating range is.

Rosa: The authors, Rosa and Dev, used this optimization approach to minimize reflection coefficients and mutual coupling between the ports.

Dev: They found that by optimizing these density variables, specifically those related to the material presence or absence at each layer, they could achieve a significant improvement over traditional methods.

Taro: Their results show two specific designs. Design one gave them about five point eight percent bandwidth in one design, and Design two pushed that much wider to nearly ten percent bandwidth.

Rosa: And what’s really interesting is that the mutual coupling between the two ports stayed below negative twenty decibels for most of the operating frequency band across both optimized designs.

Dev: That’s a solid number for isolation, especially when you're dealing with dual polarization where those coupling issues can really mess with things.

Taro: It suggests that this algorithm-based design is a useful tool when you need compact, multilayer antennas that perform well in terms of bandwidth and separation.

Rosa: It moves the goal from just making a single layer antenna better to using the whole stack of layers as one optimization variable for better performance.

Dev: So, what this means for practical applications is that we can design these complex multi-objective antennas without relying only on heavy theoretical analysis or guesswork.

Taro: The implication is that when you’re building systems like MIMO or radar where bandwidth and isolation are both tight constraints, this optimization method offers a way to explore the design space more effectively.

Rosa: It shows that using topology optimization isn't just for abstract theory anymore; it can directly inform the physical structure of a multilayer antenna.

Dev: But we still have to consider how this translates to real-world manufacturing and how robust those designs are when you put them into a production environment.

Umea University · Karlstad University · Proant AB

eess.SY, cs.CE, cs.SY

Submitted: 2026-08-06

Updated: 2026-11-16

Comments: This work has been submitted for possible publication

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 81/100

The gist: Dual-polarized (DP) microstrip antennas are utilized in wireless systems for efficient data transmission…

Key concepts

Dual-polarized (DP) Microstrip Antennas
These are antennas designed to transmit signals using two different polarizations simultaneously. This is crucial in modern wireless systems like MIMO and radar because it allows for more efficient data transmission and better signal reception.
Topology Optimization
This is an advanced design method where the physical structure of the antenna is determined by minimizing specific performance criteria, such as reflection loss or coupling. It lets the computer automatically determine the best material distribution within a given space.
Density-based Topology Optimization
In this approach, the antenna's shape is controlled by a density vector (p), where '1' means material is present and '0' means it is absent. This method allows for complex, optimized structures that are tailored to achieve specific goals like maximizing bandwidth.

Terminology

Summary

Dual-polarized (DP) microstrip antennas are utilized in wireless systems for efficient data transmission, and this contribution proposes to design DP microstrip antennas with enhanced bandwidth using a density-based topology optimization approach. p. 0

Where the paper says it

IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION, VOL. X, 2026 1 Multilayer Dual-polarized Microstrip Antenna Design by Topology Optimization with Enhanced Bandwidth Pan Lu, Eddie Wadbro, Viktor Lundstrom, Jonas Starck, Martin Berggren, Emadeldeen Hassan ¨ Abstract—Dual-polarized (DP) microstrip antennas are utilized in wireless systems for efficient data transmission.

Problem Motivation

Conventional microstrip antennas typically exhibit a narrow bandwidth which limits their performance in modern systems such as satellite communications, MIMO, and radar systems. Traditional approaches to designing DP antennas rely heavily on theoretical analysis and the expertise of design engineers. p. 0

Where the paper says it

Therefore, the design of DP microstrip antennas with enhanced bandwidth is of great significance. Traditional approaches to designing DP antennas rely heavily on theoretical analysis and the expertise of design engineers.

A common strategy to achieve dual polarizations is to impose structural symmetry on the design [4]–[8]. p. 0
Where the paper says it

Traditional approaches to designing DP antennas rely heavily on theoretical analysis and the expertise of design engineers. A common strategy to achieve dual polarizations is to impose structural symmetry on the design [4]–[8].

Optimization Formulation

The optimization problem is formulated to minimize the reflection coefficients and the mutual coupling between the feeding ports, and a gradient-based optimization algorithm is applied to solve it. The objective function is formulated as min σ log D1,1 (σ) D2,1 (σ) D1,p (σ) subject to the governing equations. p. 1

Where the paper says it

The antenna system satisfies the following energy balance, X2 i=1 W+ i + Win,Ω∞ = Wout,∞ + X2 i=1 W− i + WΩ∞, (2) where W+ i and Win,Ω∞ denote the supplied energies at port i and from a far-field source, respectively; Wout,Ω∞ denotes the outgoing energy radiated by the system; and WΩ∞ denotes the energy loss in the system. We formulate the optimization problem min σ log D1,1 (σ) D2,1 (σ) D1,p (σ) , (3) subject to the governing equations, where σ ∈ [σmin, σmax] denotes the conductivity in the design domains.

The minimization of the term D2,1 maximizes the isolation between the two ports. p. 1
Where the paper says it

Without this term, the reflection coefficient D1,1 could be trivially minimized by employing lossy designs [18]. The minimization of the term D2,1 maximizes the isolation between the two ports.

Optimization Methodology

The design variables are typically associated with the entries of a density vector p such that pi ∈ [0, 1], with 0 and 1 denoting the absence and presence of the design material. Filtering techniques are commonly employed to prevent convergence to low-performing local optima or to impose feature size control that might be useful for imposing manufacturing constraints. p. 1

Where the paper says it

In density-based topology optimization, the design variables are typically associated with the entries of a density vector p such that pi ∈ [0, 1], with 0 and 1 denoting the absence and presence of the design material, respectively. So-called filtering techniques are commonly employed to prevent convergence to low-performing local optima or to impose feature size control that might be useful for imposing manufacturing constraints.

The filtered design variables p˜ are mapped to the physical conductivity used in the simulation through σ = 109p˜−4. p. 1
Where the paper says it

, K, acting on the design vector p [17], p˜ = F K F K−1 . F 1 (p) (5) The filtered design variables p˜ are mapped to the physical conductivity used in the simulation through σ = 109p˜−4 .

The gradient of the objective function with respect to the density variables is computed using the chain rule. p. 1
Where the paper says it

Based on Yee’s scheme [20], the discretized form of (4) is given by [18] ∂W− i ∂σe = −(h) 3 XN n=1 E N−n e E ∗n− 1 2 e + E ∗n+ 1 2 e 2 ∆t, (7) where σe is the conductivity at edge e in the mesh, h and ∆t are the spatial and temporal discretization steps, respectively, Ee and E ∗ e are the electric and adjoint fields, respectively, and N is the number of total simulation time steps. From expression (7) and the mapping p 7→ σe described above, the gradient of the objective function with respect to the density variables is computed using the chain rule.

Performance Results

The optimized designs exhibit low reflection, high isolation, and enhanced bandwidth. For Design I, the −10 dB impedance bandwidth spans the frequency range 5. p. 2

Where the paper says it

59 GHz with |S11| ≈ −14 dB. The −10 dB impedance bandwidth spans the frequency range 5.

43 GHz to 5. p. 0
Where the paper says it

We present two antenna designs operating around 5. 7 GHz, which show a compromise in performance between a high isolation (more than 40 dB) and enhanced impedance bandwidth (around 10%).

75 GHz, corresponding to a fractional bandwidth of approximately 5. p. 2
Where the paper says it

43 GHz to 5. 75 GHz, corresponding to a fractional bandwidth of approximately 5.

8%. For Design II, the −10 dB bandwidth extends to a wider range from 5. p. 2
Where the paper says it

67 GHz and 6. 00 GHz in simulation and the −10 dB bandwidth extends to a wider range from 5.

59 GHz to 6. p. 0
Where the paper says it

We present two antenna designs operating around 5. 7 GHz, which show a compromise in performance between a high isolation (more than 40 dB) and enhanced impedance bandwidth (around 10%).

09 GHz with a fractional bandwidth of 9. p. 2
Where the paper says it

43 GHz to 5. 75 GHz, corresponding to a fractional bandwidth of approximately 5.

9%. The mutual coupling S21 between the two ports remains lower than −20 dB over most of the operating frequency band, which confirms the high isolation between the two ports. p. 2
Where the paper says it

Although the −10 dB impedance bandwidth is moderate, the |S11| remains below −5 dB over a wider frequency range. The magnitude of the mutual coupling |S21| between the two ports remains lower than −20 dB over most of the operating frequency band, which confirms the high isolation between the two ports.

Conclusion

Our investigations suggest that a good performance can be achieved when the excitation ports are connected to only one layer. Our results demonstrate the effectiveness of algorithm-based design as a supportive tool for employing multilayer PCBs to design compact, multiobjective microstrip antennas. p. 3

Where the paper says it

In particular, better results, particularly with respect to broadband response, are obtained when the outer design layer is actively connected to the probes. Our results demonstrate the effectiveness of algorithm-based design as a supportive tool for employing multilayer PCBs to design compact, multiobjective microstrip antennas.

TABLE I

Method Layer Size BW(%)

|---|---|---|---|

theoretical analysis(TA), optimization algorithms (OA) 1 1.44 × 1.44 × 0.024 1.8%

OA 2 [5.46,6.03] OA 2 0.50 × 0.50 × 0.031 9.9%

REFERENCES

[1] P. K. Mishra, D. R. Jahagirdar, and G. p. 3

Where the paper says it

REFERENCES [1] P. Jahagirdar, and G.

Kumar, “A review of broadband dual linearly polarized microstrip antenna designs with high isolation [Education Column],” IEEE Antenn. p. 3
Where the paper says it

Jahagirdar, and G. Kumar, “A review of broadband dual linearly polarized microstrip antenna designs with high isolation [Education Column],” IEEE Antenn.

Propag., vol. 56, no. 6, pp. 238–251, 2014

[2] Y. Zhang, P. Li, X. Qin, P. Liang, K. Wei, and Y. p. 3

Where the paper says it

238–251, 2014. Wei, and Y.

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. p. 3
Where the paper says it

Wei, and Y. Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans.

Antennas Propag. p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

p. 3
Where the paper says it

Li, “Dual-polarized microstrip antenna with single-dimension-constraint resonant frequency,” IEEE Trans. Antennas Propag, vol.

, vol. 72, no. 11, pp. 8365–8374, 2024

[3] B. Feng, L. Li, J.-C. Cheng, and C. p. 4

Where the paper says it

X, 2026 5 [3] B. Cheng, and C.

-Y.-D. Sim, “A dual-band dualpolarized stacked microstrip antenna with high-isolation and band-notch characteristics for 5G microcell communications,” IEEE Trans. p. 4
Where the paper says it

Cheng, and C. Sim, “A dual-band dualpolarized stacked microstrip antenna with high-isolation and band-notch characteristics for 5G microcell communications,” IEEE Trans.

Antennas Propag., vol. 67, no. 7, pp. 4506–4516, 2019

[4] C. Chen, “A single-layer single-patch dual-polarized high-gain crossshaped microstrip patch antenna,” IEEE Antennas Wirel. p. 4

Where the paper says it

4506–4516, 2019. Chen, “A single-layer single-patch dual-polarized high-gain crossshaped microstrip patch antenna,” IEEE Antennas Wirel.

Propag. Lett., vol. 22, no. 10, pp. 2417–2421, 2023

[5] X. Zhou, F. Wu, Y. Tong, L. Tian, and Z. p. 4

Where the paper says it

2417–2421, 2023. Tian, and Z.

-G. Liu, “Ultrawideband linear-polarized and dual-polarized ME dipole and their array for 5G/6G applications,” IEEE Antennas Wirel. p. 4
Where the paper says it

Tian, and Z. Liu, “Ultrawideband linear-polarized and dual-polarized ME dipole and their array for 5G/6G applications,” IEEE Antennas Wirel.

Propag. Lett., vol. 25, no. 1, pp. 149–153, 2026

[6] S.-H. Zhu, X.-S. Yang, L.-L. Wang, and J. p. 4

Where the paper says it

149–153, 2026. Wang, and J.

Wang, “Hybrid topology optimization of dual-polarized wide-beam antenna and its application in wide-angle scanning array,” Int. p. 4
Where the paper says it

Wang, and J. Wang, “Hybrid topology optimization of dual-polarized wide-beam antenna and its application in wide-angle scanning array,” Int.

J. RF Microw. Comput.-Aided Eng. p. 4
Where the paper says it

Wang, “Hybrid topology optimization of dual-polarized wide-beam antenna and its application in wide-angle scanning array,” Int. -Aided Eng.

p. 4
Where the paper says it

Wang, “Hybrid topology optimization of dual-polarized wide-beam antenna and its application in wide-angle scanning array,” Int. -Aided Eng.

, vol. 32, no. 3, p. e23011, 2022

[7] Y. He and Y. Li, “Dual-polarized microstrip antennas with capacitive via fence for wide beamwidth and high isolation,” IEEE Trans. p. 4

Where the paper says it

e23011, 2022. Li, “Dual-polarized microstrip antennas with capacitive via fence for wide beamwidth and high isolation,” IEEE Trans.

Antennas Propag., vol. 68, no. 7, pp. 5095–5103, 2020

[8] Q. Wu, Y. Shi, and L. p. 4

Where the paper says it

5095–5103, 2020. Shi, and L.

Li, “Wideband dual-polarized differential-fed filtering microstrip patch antenna with high suppression and wide stopband,” Int. p. 4
Where the paper says it

Shi, and L. Li, “Wideband dual-polarized differential-fed filtering microstrip patch antenna with high suppression and wide stopband,” Int.

J. RF Microw. Comput.-Aided Eng., vol. 2023, no. 1, p. 6682038, 2023

[9] W. T. Li, W. X. Cai, J. G. He, Y.-Q Hei, and X. p. 4

Where the paper says it

6682038, 2023. Hei, and X.

-W Shi, “Low-profile wideband dual-polarized antenna for millimeter-wave beam steering applications,” IEEE Trans. p. 4
Where the paper says it

Hei, and X. Shi, “Low-profile wideband dual-polarized antenna for millimeter-wave beam steering applications,” IEEE Trans.

Antennas Propag., vol. 71, no. 10, pp. 7741–7751, 2023

[10] S. Koziel and A. p. 4

Where the paper says it

7741– 7751, 2023. Koziel and A.

Pietrenko-Dabrowska, “Tolerance-aware multiobjective optimization of antennas by means of feature-based regression surrogates,” IEEE Trans. p. 4
Where the paper says it

Koziel and A. Pietrenko-Dabrowska, “Tolerance-aware multiobjective optimization of antennas by means of feature-based regression surrogates,” IEEE Trans.

Antennas Propag., vol. 70, no. 7, pp. 5636–5646, 2022

[11] J. Li, W.-Q Qiu, P. Xiao, Z.-Liu, G. Li, W. T Joines, and S Liao, “An adaptive evolutionary neural network-based optimization design method for wideband dual-polarized antennas,” IEEE Trans. p. 4

Where the paper says it

Joines, and S. Liao, “An adaptive evolutionary neural network-based optimization design method for wideband dual-polarized antennas,” IEEE Trans.

Antennas Propag., vol. 71, no. 10, pp. 8165–8172, 2023

[12] L.-L Wang, X. p. 4

Where the paper says it

149–153, 2026. Wang, and J.

-S Yang, and C. p. 4
Where the paper says it

8165–8172, 2023. Yang, and C.

-J Ma, “An efficient gradient-based hybrid parameter-topology optimization for antenna design,” IEEE Trans. p. 4
Where the paper says it

Yang, and C. Ma, “An efficient gradient-based hybrid parameter-topology optimization for antenna design,” IEEE Trans.

Antennas Propag., vol. 71, no. 12, pp. 9477–9486

[13] P Lu, E Wadbro, J Starck, M Berggren, and E Hassan, “Topology optimization of decoupling feeding networks for antenna arrays,” IEEE Trans. Antennas Propag., vol. 74, no. 1, pp. 467–479

[14] A H Bokhari, E Hassan, and E Wadbro, “Topology optimization of microwave frequency dividing multiplexers,” Struct. Multidiscip. p. 4

Where the paper says it

Wadbro, “Topology optimization of microwave frequency dividing multiplexers,” Struct. Multidiscip.

p. 4
Where the paper says it

Wadbro, “Topology optimization of microwave frequency dividing multiplexers,” Struct. Multidiscip.

Optim., vol. 66, no. 5, p. 106

[15] E Hassan, B Scheiner, F Michler, M Berggren, E Wadbro, F Rohrl, Z Zorn, R Weigel, and F Lurz, “Multilayer topology optimization of wideband SIW-to-waveguide transitions,” IEEE Trans. Microw. Theory Techn. p. 4

Where the paper says it

Lurz, “Multilayer topology optimization of wideband SIW-to-waveguide transitions,” IEEE Trans. Theory Techn.

, vol. 68, no. 4, pp. 1326–1339

[16] J Gedeon, I Allayarov, A Cala Lesina, and E Hassan, “Time-domain topology optimization of power dissipation in dispersive dielectric and plasmonic nanostructures,” IEEE Trans. Antennas Propag., vol. 73, no. 5, pp. 3079–3094

[17] E Hassan, E Wadbro, L Hagg, and M Berggren, “Topology optimization of compact wideband coaxial-to-waveguide transitions with minimum-size control,” Struct. Multidiscip. Optim., vol. 57, pp. 1765–1777

[18] E Hassan, E Wadbro, and M Berggren, “Topology optimization of metallic antennas,” IEEE Trans. Antennas Propag., vol. 62, no. 5, pp. 2488–2500

[19] J A Roden and S D Gedney, “Convolution PML (CPML): An efficient FDTD implementation of the CFS–PML for arbitrary media,” Microw. Opt. Technol. Lett., vol. 27, no. 5, pp. 334–339, 2000

[20] A Taflove and S C Hagness, Computational electrodynamics: the finitedifference time-domain method, 3rd ed. Norwood: Artech House, 2005

[21] K Svanberg, “A class of globally convergent optimization methods based on conservative convex separable approximations,” SIAM J. Optim., vol. 12, no. 2, p. 555–573, 2002

[22] High Performance Computing Center North (HPC2N), 2026, accessed: https://www.hpc2n.umu.se/

| Method | Layer Size | BW |

|---|---|---|

theoretical analysis(TA) 1.44 × 1.44 × 0.024 1.8%

OA [5.46,6.03] OA 2 0.50 × 0.50 × 0.031 9.9%

| Method | Layer Size | BW |

|---|---|---|

theoretical analysis(TA) [5.46,6.03] OA 2 0.50 × 0.50 × 0.031 9.9%

| Method | Layer Size | BW |

|---|---|---|

theoretical analysis(TA) [5.46,6.03] OA 2 0.50 × 0.50 × 0.031 9.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI system can design planar multilayer dual polarized microstrip antennas with enhanced bandwidth using a densitybased topology optimization approach to minimize reflection coefficients and mutual coupling while maximizing outgoing energy for low lossy material selection.

  2. The improved system can perform design iterations by calculating the objective function gradient via the adjoint field method, as described by equation (4), enabling gradient-based optimization of the design vector p through the globally convergent method of moving asymptotes (GCMMA).

  3. The AI system can incorporate manufacturing constraints into the optimization process using filtering techniques, specifically applying a nonlinear filter that reduces intermediate densities and controls the minimum feature size to prevent convergence to low-performing local optima.

  4. The system can achieve better broadband performance by simultaneously optimizing copper distribution in two layers of an FR4 stack-up, allowing both layers to develop different resonance modes when one layer is connected and the other is disconnected.

Abstract

Dual-polarized (DP) microstrip antennas are utilized in wireless systems for efficient data transmission. However, their bandwidth is typically very limited. In this contribution, we propose to design DP microstrip antennas with enhanced bandwidth using a density-based topology optimization approach. We formulate an optimization problem that simultaneously accounts for feeding port matching, the ports' isolation, and far-field dual-polarized performance. To enhance the bandwidth, we employ an FR4 stack-up, in which the copper on two layers is optimized simultaneously. We present two antenna designs operating around 5.7 GHz, which show a compromise in performance between a high isolation (more than 40 dB) and enhanced impedance bandwidth (around 10%). The optimized designs are experimentally validated, showing an excellent agreement between the simulated and measured performance.

Related papers