UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles

arXiv:2608.01843 · eess.SP, cs.HC · Submitted 2026-08-03 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: We're looking at the paper: "UART for Wearables (U4We)".

Dev: Here's the gist of the paper. UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules This brief proposes a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules The resulting design framework determines whether a given combination of data rate, textile capacitance, and resistance is feasible These results establish a basic methodology for textile-based simultaneous power and data transfer.

Rosa: System Concept The garment consists of two conductive textile layers separated by an insulating layer, and modules are attached by a pin-and-clutch fastener that contacts both layers without sewing or adhesives The textile thus functions as a two-dimensional shared medium that distributes power and signals to modules at arbitrary positions.

Dev: The skin-side conductive layer is at a single common potential over its entire surface, whichever rail it is assigned to, and the bus voltage appears only across the thin insulating layer between the two conductive layers.

Rosa: Medium Access and Physical Layer Signals injected at one point propagate over the entire medium, and the physical layer therefore forms a broadcast bus Here, master-initiated half-duplex access is adopted.

Paper summary: Rosa: So, this paper, "UART for Wearables: DC Power and Carrierless Signal Transfer over Conductive Textiles," it's proposing a circuit-level way to connect battery-less wearable modules using conductive textiles.

Dev: It claims they can do simultaneous power transfer and data signals over this textile medium without needing wires between every module.

Rosa: Basically, they use two layers of conductive fabric separated by an insulator, and the textile acts like a shared bus that powers everything at once.

Dev: The core idea is to couple the universal asynchronous receiver transmitter pulses directly onto this textile using AC coupling capacitors instead of carrier modulation.

Rosa: They model the textile as a single lumped resistance capacitance network and derive design conditions for how fast you can transmit data and how much resistance or capacitance you can use on that fabric.

Dev: The thesis is determining whether a certain combination of data rate, textile capacitance, and resistance is actually feasible for this simultaneous power and data transfer.

Taro: I'm curious about the physical setup, Rosa; how does this textile thing actually work as a medium for both DC power and signals?

Rosa: Well, the garment has one skin-side conductive layer that stays at a single common potential across its whole surface, and the bus voltage only appears across that thin insulating layer between the two layers.

Dev: That setup means power is supplied through an inductor which keeps the power path separate from the signal components, while a capacitor couples those UART signals through it to block any DC flow.

Taro: If I'm looking at this from a real-world failure mode perspective, what happens when the world misbehaves and we need to know how robust this physical connection is?

Rosa: The paper sets up a model where they look at critical damping for the second-order circuit response, which is crucial because it dictates how reliably you can recover the received pulse signal with a simple data slicer.

Dev: They found that for critical damping, which means the damping ratio zeta equals one, each pulse edge converts into a non-oscillatory spike that returns to zero without polarity reversal.

Rosa: That sounds like a stable way to read the data, but they're still dealing with those design constraints on resistance and capacitance values.

Dev: They derive the required conditions for this critical damping by looking at how fast the pulse length, which we call TS, interacts with the natural frequency of the system.

Taro: So if you want to ensure that successive edges don't interfere, what specific condition are they using there?

Rosa: They state that if the pulse length TS satisfies omega zero times TS is greater than two pi, then successive edges do not interfere, which leads directly to the design conditions for critical damping.

Dev: This whole framework helps determine the feasible region of how much inductance and resistance you can have on your textile bus.

Conclusion: Rosa: So, looking at this paper's title, "UART for Wearables: DC Power and Carrierless Signal Transfer over Conductive Textiles," it really sums up what they achieved.

Dev: It’s about creating a circuit-level interconnection technique for battery-less distributed wearable modules using conductive textiles.

Rosa: The main contribution is establishing that design framework for simultaneous power and data transfer over these textile-based systems.

Taro: What this means for us is that we can build these modular devices without the heavy wiring overhead you usually have to deal with in traditional electronics.

Dev: It opens up a path where you can determine if a specific combination of data rate, textile capacitance, and resistance is actually feasible for this kind of transfer.

Rosa: They validated their model in a one-way configuration using an LED array as the representative setup.

Dev: They confirmed that UART communication at one megabit per second was achievable under those representative conditions.

Taro: So, while it works in a controlled setting, what are the limitations they point out?

Rosa: They mention that their demonstrated operating point of M equals twenty-eight is just one experimentally verified operating point in the design space, not a universal upper limit.

Dev: And they also state that any non-negligible aggregate receiver parasitic capacitance needs to be included when calculating the effective capacitance on the textile, which adjusts their model.

Rosa: It shows that while this approach is promising for low overhead connections, you still have to deal with these textile-specific parameters and ensure your design stays within those derived bounds.

Dev: The implication is a methodology for textile-based simultaneous power and data transfer using UART interfaces at one megabit per second.

Taro: It shifts the focus from just the circuit design to needing effective parameter characterization for different textiles when you want to apply this beyond this one specific setup.

Akihito Noda

School of Systems Engineering, Kochi University of Technology

eess.SP, cs.HC

Submitted: 2026-08-03

Updated: 2026-09-19

Comments: 5 pages, 8 figures, 2 tables

Journal ref: IEEE Transactions on Circuits and Systems II: Express Briefs, vol. 73, no. 11, pp. 1154-1158 (2026)

DOI: 10.1109/TCSII.2026.3735640

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 77/100

The gist: UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable…

Key concepts

Conductive Textile Interconnection
This is the physical setup where modules are attached to two conductive fabric layers separated by an insulator. The textile acts as a shared medium that distributes both DC power and digital signals to any module on the garment without needing individual wires.
Lumped Capacitance Model (Ctex)
The textile is modeled simply as a single lumped capacitance (Ctex). This simplification is valid because the garment behaves like an electrically short circuit at the signal frequency. This model helps derive analytical conditions for how the received signal will behave.
Critical Damping ($α = 1$)
Critical damping is a design goal where the system's response to a pulse is non-oscillatory, meaning it returns to zero without overshooting. This condition ensures that successive data pulses do not interfere with each other, allowing for reliable signal recovery using a simple comparator.
Design Space (Lα vs. Ctex)
This defines the range of possible circuit component values (like inductor size Lα and textile capacitance Ctex) that allow the system to work correctly. The paper shows how constraints like critical damping set a lower bound for Lα based on textile resistance and capacitance.

Terminology

Summary

UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules This brief proposes a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules The resulting design framework determines whether a given combination of data rate, textile capacitance, and resistance is feasible These results establish a basic methodology for textile-based simultaneous power and data transfer. p. 0

Where the paper says it

ACCEPTED MANUSCRIPT 1 UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles Akihito Noda, Member, IEEE Abstract—This brief presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules. Two conductive textile layers separated by an insulating fabric layer are used as a garment-wide shared bus that simultaneously conveys DC power and pulse-based data signals without point-to-point wiring.

System Concept

The garment consists of two conductive textile layers separated by an insulating layer, and modules are attached by a pin-and-clutch fastener that contacts both layers without sewing or adhesives The textile thus functions as a two-dimensional shared medium that distributes power and signals to modules at arbitrary positions. The skin-side conductive layer is at a single common potential over its entire surface, whichever rail it is assigned to, and the bus voltage appears only across the thin insulating layer between the two conductive layers. p. 0

Where the paper says it

The textile thus functions as a two-dimensional shared medium that distributes power and signals to modules at arbitrary positions. The skin-side conductive layer is at a single common potential over its entire surface, whichever rail it is assigned to, and the bus voltage appears only across the thin insulating layer between the two conductive layers.

Medium Access and Physical Layer

Signals injected at one point propagate over the entire medium, and the physical layer therefore forms a broadcast bus Here, master-initiated half-duplex access is adopted. Collision avoidance belongs to the medium-access control layer, whereas this brief addresses the physical layer. p. 1

Where the paper says it

Collision avoidance belongs to the medium-accesscontrol layer, whereas this brief addresses the physical layer. Here, master-initiated half-duplex access is adopted.

The proposed scheme confines the signal band so that the entire bus is far smaller than the signal wavelength DC power and UART pulses are multiplexed with an inductor and a capacitor (Fig. p. 1
Where the paper says it

An RX module drives the bus only when polled, collisions are detected by UART framing/checksum errors, and listen-before-talk can be added in firmware. Physical-Layer Considerations The proposed scheme confines the signal band so that the entire bus is far smaller than the signal wavelength; the next section quantifies this lumped-element regime.

2). Power is supplied through the inductor, which isolates the power path from signal components, while the UART signal couples through a capacitor that blocks DC. p. 1
Where the paper says it

DC power and UART pulses are multiplexed with an inductor and a capacitor (Fig. Power is supplied through the inductor, which isolates the power path from signal components, while the UART signal couples through a capacitor that blocks DC.

Circuit Modeling and Design Criteria

The textile shared bus is modeled as a single lumped capacitance Ctex The received voltage is expressed in the Laplace domain as VRX(s) = V0(s) (1/RD) 1/RD + sCtex + 1/sL∥. For critical damping, ζ = 1, the response becomes VRX(s) = 2ω0/(s + ω0)2. p. 2

Where the paper says it

For ζ = 1, (1) becomes VRX(s) = 2ω0/(s + ω0) 2 and its inverse Laplace transform gives vRX(t) ≡ L−1 {VRX(s)} = 2ω0te −ω0t . (3) Under critical damping (Fig.

The second requirement is sufficiently fast decay, ω0TS > 2π. p. 2
Where the paper says it

Substituting it into (2) gives 2RD = √︂ L∥/Ctex. (4) The second is sufficiently fast decay, ω0TS > 2π (Section III), which with (2) yields the upper bound L∥ < T 2 S 4π 2Ctex .

Design Space and Validation

The design constraints are summarized in Fig. 5, where TS sets the upper bound of the feasible L∥ region and Rtex sets the lower bound. p. 2

Where the paper says it

(6) The design constraints are summarized in Fig. 5, where TS sets the upper bound of the feasible L∥ region and Rtex sets the lower bound.

A lower bound on L∥ is obtained from the critical-damping relation (4) together with the constraint RD > Rtex as L∥ > 4R2/texCtex. p. 2
Where the paper says it

2 nF, L∥ = 8. A lower bound on L∥ is obtained from the critical-damping relation (4) together with the constraint RD > Rtex as L∥ > 4R 2 texCtex.

The prototype validates the model in a one-way configuration with one TX commanding multiple RX modules, representative of an LED array. p. 2
Where the paper says it

Larger or accumulated drifts are compensated by readjusting the trimmer, which restores ζ = 1 through RD = 1 2 √︁ L∥/Ctex. HARDWARE IMPLEMENTATION AND EXPERIMENTAL VALIDATION The prototype validates the model in a one-way configuration with one TX commanding multiple RX modules, representative of an LED array.

The measured textile-line waveforms agree well with Fig. p. 3
Where the paper says it

7 were obtained for a representative single-RX configuration, probing the TX UART output, the RX pickup electrode, and the RX MCU UART input, for comparison with Fig. The measured textile-line waveforms agree well with Fig.

4. The results validate the circuit model and the critically damped design strategy, and UART communication at 1 Mb/s was confirmed under the representative condition. p. 3
Where the paper says it

The overdamped case leaves history-dependent peaks due to incomplete return, and the underdamped case produces oscillatory transients that cause false RXD transitions. These results validate the circuit model and the critically damped design strategy, and UART communication at 1 Mb/s was confirmed under the representative condition.

Conclusion

This work presented a conductive-textile interconnection scheme for batteryless, antennaless modules using a UART interface and a minimal added circuit, at 1 Mb/s, near the typical upper rate of MCU UARTs The main contribution of this work is a circuit model and design methodology for textile-based simultaneous power and data transfer, together with the effective-parameter characterization required to apply it to other textiles. Future work includes quantitative characterization of baseline and parameter variation under controlled deformation, stretching/washing durability, statistical contact characterization, bidirectional multi-node protocols, and distributed RLGC modeling for larger media or higher rates. p. 4

Where the paper says it

The main contribution of this work is a circuit model and design methodology for textile-based simultaneous power and data transfer, together with the effective-parameter characterization required to apply it to other textiles. Quantitative characterization of baseline and parameter variation under controlled deformation, stretching/washing durability, statistical contact characterization, bidirectional multi-node protocols, and distributed RLGC modeling for larger media or higher rates remain future work.

The feasible region of Fig. p. 2
Where the paper says it

1 1 10 100 L∥ (µ H) Ctex (nF) TS = 0. 1 µs TS = 1 µs (1 Mb/s) TS = 10 µs Rtex = 1 Ω Feasible region Faster UART Larger Rtex ★ Fig.

5 shows the feasible region of Fig. p. 2
Where the paper says it

1 1 10 100 L∥ (µ H) Ctex (nF) TS = 0. 1 µs TS = 1 µs (1 Mb/s) TS = 10 µs Rtex = 1 Ω Feasible region Faster UART Larger Rtex ★ Fig.

5. Any non-negligible aggregate receiver parasitic capacitance is included in the effective Ctex. p. 4
Where the paper says it

the feasible region of Fig. Any non-negligible aggregate receiver parasitic capacitance is included in the effective Ctex.

The demonstrated M = 28 is thus one experimentally verified operating point in this design space, not a universal upper limit. p. 4
Where the paper says it

At exact critical damping, (3) has a peak amplitude of 2/e of the applied step, which does not scale with M. The demonstrated M = 28 is thus one experimentally verified operating point in this design space, not a universal upper limit.

TABLE I

DESIGN PARAMETERS AND CHARACTERIZED TEXTILE PROPERTIES OF THE PROTOTYPE

Symbol Value Unit Ctex 1.2 nF RD Rtex + Rvar Rtex 0. p. 3

Where the paper says it

ACCEPTED MANUSCRIPT 4 TABLE I DESIGN PARAMETERS AND CHARACTERIZED TEXTILE PROPERTIES OF THE PROTOTYPE Symbol Value Unit Ctex 1. 2 nF RD Rtex + Rvar Rtex 0.

5 omega Rvar 0–200 omega LTX 8. p. 3
Where the paper says it

2 nF RD Rtex + Rvar Rtex 0. 5 Ω Rvar 0–200 Ω LTX 8.

3 µH LRX 1000 µH L∥ = LTX∥(LRX/M)(M = 1)8. p. 3
Where the paper says it

5 Ω Rvar 0–200 Ω LTX 8. 3 µH LRX 1000 µH L∥ = LTX ∥ (LRX/M) (M = 1) 8.

2 µH M: number of RXs (M = 28)6. p. 3
Where the paper says it

3 µH LRX 1000 µH L∥ = LTX ∥ (LRX/M) (M = 1) 8. 2 µH M: # of RXs (M = 28) 6.

7 Sheet resistance (datasheet [20])≤0. p. 3
Where the paper says it

2 µH M: # of RXs (M = 28) 6. 7 Sheet resistance (datasheet [20]) ≤0.

1 omega/□ Capacitance per area 0. p. 2
Where the paper says it

The representative design example is summarized in Table I, and the case of M = 1 is indicated by the star in Fig. The table also lists the measured bus parameters: the sheet resistance [20], and the capacitance per unit area obtained from the lumped capacitance measured between the assembled layers with a digital multimeter.

75 pF/cm2 Insulator thickness 0. p. 3
Where the paper says it

1 Ω/□ Capacitance per area 0. 75 pF/cm2 Insulator thickness 0.

6 mm Loop resistance, 10/20/30 cm(4-wire) 0. p. 3
Where the paper says it

75 pF/cm2 Insulator thickness 0. 6 mm Loop resistance, 10/20/30 cm (4-wire) 0.

25/0.32/0.37 omega LRX saturation-current rating 25 mA Rated aggregate RX current (M = 28)0. p. 3
Where the paper says it

6 mm Loop resistance, 10/20/30 cm (4-wire) 0. 37 Ω LRX saturation-current rating 25 mA Rated aggregate RX current (M = 28) 0.

70 A Worst-case common-path drop(0. p. 3
Where the paper says it

37 Ω LRX saturation-current rating 25 mA Rated aggregate RX current (M = 28) 0. 70 A Worst-case common-path drop (0.

70 A) 0.50 V LRX drop at 25 mA 0. p. 3
Where the paper says it

37 Ω LRX saturation-current rating 25 mA Rated aggregate RX current (M = 28) 0. 70 A Worst-case common-path drop (0.

60 V Available RX voltage at 25 mA 3. p. 3
Where the paper says it

50 V LRX drop at 25 mA 0. 60 V Available RX voltage at 25 mA 3.

90 V Available aggregate RX power (M = 28)2. p. 3
Where the paper says it

60 V Available RX voltage at 25 mA 3. 90 V Available RX power at 25 mA 97 mW Available aggregate RX power (M = 28) 2.

7 W

TABLE II

COMPARISON WITH TEXTILE POWER-AND-DATA TRANSFER SCHEMES

Scheme TDM TDM FDM Baseband Cont. power No No Yes Yes Carrierless Yes Yes No Yes Interface1 Charge/comm. p. 4

Where the paper says it

ACCEPTED MANUSCRIPT 5 TABLE II COMPARISON WITH TEXTILE POWER-AND-DATA TRANSFER SCHEMES [14] [15] I2We [16] U4We Scheme TDM TDM FDM Baseband Cont. power No No Yes Yes Carrierless Yes Yes No Yes Interface1 Charge/comm.

switch ASK modem LC + comp. p. 4
Where the paper says it

power No No Yes Yes Carrierless Yes Yes No Yes Interface1 Charge/comm. switch ASK modem LC + comp.

Data rate 9. p. 0
Where the paper says it

From this model, design conditions for comparator-based waveform recovery and high-bitrate transmission are analytically derived. The resulting design framework determines whether a given combination of data rate, textile capacitance, and resistance is feasible, and also provides the corresponding design range of the decoupling inductors.

6 kb/s 1.5 Mb/s2 100 kb/s 1 Mb/s Nodes3 5 10828 Effective rate at 10 slaves(5 Mbaud burst UART with charging duty)

Fig. 8

28-RX prototype on the shared textile bus The M5Atom TX with a U4We adapter selectively activates RX modules by address-based control the feasible region of Fig. 5 Any non-negligible aggregate receiver parasitic capacitance is included in the effective Ctex at exact critical damping, (3) has a peak amplitude of 2/e of the applied step which does not scale with M The demonstrated M = 28 is thus one experimentally verified operating point in this design space, not a universal upper limit

Fig. 6

Schematic diagram of the experimental prototype(relevant portion) TXD (V) vRX (V) RD≈8 omega(ζ≈5) RD≈40 omega(ζ≈1) RD≈200 omega(ζ≈0.2)

Fig. 7

Measured waveforms at 1 Mbaud (TS = 1 µs), single-RX configuration: (top) TX UART output (critical condition; common to all cases), (middle) textile-line voltage, (bottom) reconstructed RXD input under underdamped, near-critical, and overdamped settings

Fig. 5

Design space of L∥ vs. Ctex TS sets the upper bound and Rtex(critical damping) the lower bound Highlighted: TS = 1 µs, Rtex = 1 omega The region shrinks for shorter TS or larger Rtex Star: design example of Section V (Ctex = 1. p. 2

Where the paper says it

The region shrinks for shorter TS or larger Rtex. Star: design example of Section V (Ctex = 1.

2 nF, L∥ = 8.2 µH)

Fig. 4

Step response waveforms The undershoot for ζ 1 are annotated The next-edge line indicates an example timing of the next pulse edge satisfying the design condition ω0TS > 2π

Fig. 3

AC equivalent circuit of the TX–textile–RX signal path after open/short approximations at the signal frequency, with all module inductors combined into L∥

Fig. 2

Simultaneous DC power and serial data transmission on textile Power is supplied through the inductor, which isolates the power path from signal components, while the UART signal couples through a capacitor that blocks DC

Fig. 1

Concept: wearable modules attached to double-sided conductive textile via pin-and-socket fasteners share DC power and digital pulses

--- Page 1 ---

ACCEPTED MANUSCRIPT 1

UART for Wearables (U4We): DC Power and Carrierless Signal Transfer over Conductive Textiles Akihito Noda, Member, IEEE Abstract—This brief presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules Two conductive textile layers separated by an insulating fabric layer are used as a garment-wide shared bus that simultaneously conveys DC power and pulse-based data signals without point-to-point wiring To minimize the circuit overhead of each module, universal asynchronous receiver/transmitter (UART) pulses are directly coupled onto the textile through AC-coupling capacitors without carrier modulation The textile is modeled as a lumped resistance–capacitance network From this model, design conditions for comparator-based waveform recovery and high-bitrate transmission are analytically derived

--- Page 2 ---

ACCEPTED MANUSCRIPT 2

Fig. 1 Concept: wearable modules attached to double-sided conductive textile via pin-and-socket fasteners share DC power and digital pulses Fig. p. 1

Where the paper says it

ACCEPTED MANUSCRIPT 2 Fig. Concept: wearable modules attached to double-sided conductive textile via pin-and-socket fasteners share DC power and digital pulses.

2 Simultaneous DC power and serial data transmission on textile

--- Page 3 ---

ACCEPTED MANUSCRIPT ACCEPTED MANUSCRIPT 3

AC equivalent circuit of the signal path through the conductive textile is shown in Fig. 3 It is derived by applying the following approximations First of all, the textile shared bus is modeled as a single lumped capacitance Ctex This is justified because the garment is electrically short at the occupied bandwidth At the signal frequency, the TX DC source and the ACcoupling capacitor are treated as short circuits On the RX side, the data-slicer input is open and the smoothing capacitor following the decoupling inductor is a short, leaving only the inductor Based on this simplified model, the transient response of the received pulse waveform can be derived analytically

--- Page 4 ---

ACCEPTED MANUSCRIPT 4

The design parameters are L∥ and RD, subject to RD > Rtex, where Rtex denotes the total series resistance of the signal path including textile spreading and fastener contact resistance Garment-scale Ctex is typically on the order of nanofarads, and Rtex of metal-plated fabrics on the order of 1 omega which sets the practical design range

--- Page 5 ---

ACCEPTED MANUSCRIPT 5

Deviations from ζ = 1 produce a finite undershoot (ζ 1) in the received waveform (Fig. 4) An undershoot of magnitude Vus > ∆Vhys falsely triggers the comparator Larger or accumulated drifts are compensated by readjusting the trimmer, which restores ζ = 1 through RD = 1/2√L∥/Ctex. p. 2

Where the paper says it

01Vpeak at ζ = 0. p. 2

Where the paper says it

The margin is still wide because the deviations grow slowly; Vus ≈ 0. 01Vpeak at ζ = 0.

Larger or accumulated drifts are compensated by readjusting the trimmer, which restores ζ = 1 through RD = 1 2 √︁ L∥/Ctex.

The margin is still wide because the deviations grow slowly; Vus ≈ 0. p. 2
Where the paper says it

Because Vpeak ≫ ∆Vhys by design, the tolerance is asymmetric, and the undershoot side is the binding constraint. The margin is still wide because the deviations grow slowly; Vus ≈ 0.

01Vpeak at ζ = 0.82

--- Page 6 ---

ACCEPTED MANUSCRIPT ACCEPTED MANUSCRIPT 3

Under critical damping (Fig. 4) each pulse edge is converted into a non-oscillatory spike of corresponding polarity that returns to zero without polarity reversal, so a comparator with minimal hysteresis can recover the waveform Hence, if the pulse length TS satisfies ω0TS > 2π successive edges do not interfere. p. 2

Where the paper says it

4), each pulse edge is converted into a non-oscillatory spike of corresponding polarity that returns to zero without polarity reversal, so a comparator with minimal hysteresis can recover the waveform. The spike peaks at ω0t = 1 and decays substantially by ω0t ≈ 2π.

The spike peaks at ω0t = 1 and decays substantially by ω0t ≈ 2π Hence, if the pulse length TS satisfies ω0TS > 2π successive edges do not interfere. p. 2
Where the paper says it

The spike peaks at ω0t = 1 and decays substantially by ω0t ≈ 2π. Hence, if the pulse length TS satisfies ω0TS > 2π, successive edges do not interfere.

Critical damping and sufficiently fast decay are thus the two receiver requirements leading directly to the design conditions in the next section

--- Page 7 ---

ACCEPTED MANUSCRIPT 5

The prototype validates the model in a one-way configuration with one TX commanding multiple RX modules, representative of an LED array The rating-based 28-RX DC power budget is summarized in Table I and is independent of 1 Mb/s signaling Pulse edges are suppressed toward the local supply by the LRX–C filter by ω0LRXC ≥ 104(C ≥ 0.1 µF) to the submillivolt level TX-supply ripple reaches the bus through (L∥/LTX)ω02/s2 + 2ζω0s + ω02/s2; at ζ = 1 it has no peaking and gain at most L∥/LTX ≈ 0. p. 3

Where the paper says it

1 µF), to the submillivolt level. TX-supply ripple reaches the bus through (L∥/LTX) ω 2 0/(s 2 + 2ζω0s + ω 2 0 ); at ζ = 1 it has no peaking and gain at most L∥/LTX ≈ 0.

8

--- Page 8 ---

ACCEPTED MANUSCRIPT ACCEPTED MANUSCRIPT 3

Ripple above 1 kHz should remain below ∆Vhys, while sub-kHz components are tracked by the threshold A load-step-induced voltage variation at an RX supply couples back to the bus through the same transfer function with LTX replaced by LRX; at ζ = 1 its gain is at most L∥/LRX ≈ 6.7 × 10−3 for M = 28

--- Page 9 ---

ACCEPTED MANUSCRIPT ACCEPTED MANUSCRIPT 3

The rating-based 28-RX DC power budget is summarized in Table I and is independent of 1 Mb/s signaling Pulse edges are suppressed toward the local supply by the LRX–C filter by ω0LRXC ≥ 104(C ≥ 0.1 µF) to the submillivolt level TX-supply ripple reaches the bus through (L∥/LTX)ω02/s2 + 2ζω0s + ω02/s2 at ζ = 1 it has no peaking and gain at most L∥/LTX ≈ 0. p. 3

Where the paper says it

1 µF), to the submillivolt level. TX-supply ripple reaches the bus through (L∥/LTX) ω 2 0/(s 2 + 2ζω0s + ω 2 0 ); at ζ = 1 it has no peaking and gain at most L∥/LTX ≈ 0.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved AI systems can perform continuous, carrierless power and data transfer at 1 Mb/s over a garment using a UART interface with minimal circuit complexity. This allows for batteryless distributed wearable modules to be powered and individually addressed without point-to-point wiring or traditional carrier modulation.

  2. The system enables the design of robust textile-based simultaneous power and data transfer by deriving analytical design conditions for comparator-based waveform recovery and high-bitrate transmission based on a lumped resistance–capacitance network model. This methodology determines the feasibility of a given data rate, textile capacitance, and resistance, providing a corresponding design range for decoupling inductors.

  3. AI systems can be designed to manage signal integrity under parameter drift by implementing an in-line trimmer that restores critical damping conditions when the system deviates from zeta equals one. This ensures that successive pulse edges do not interfere with each other, preserving correct RXD recovery even when textile parameters change due to moisture or pressure.

  4. The improved system utilizes a master-initiated half-duplex access protocol for broadcast operation over the shared conductive textile bus, where collision avoidance is handled at the medium-access control layer. This allows multiple modules to observe practically the same waveform with negligible propagation delay relative to symbol duration.

  5. AI systems can select optimal hardware configurations, such as choosing inductor values near the upper bound of L parallel, to mitigate dependence on the number of receiver modules M while maintaining stable operation without readjusting critical conditions. This confirms that a stable multi-node configuration is possible by tuning L parallel based on the required number of RX modules.

Abstract

This brief presents a circuit-level conductive-textile interconnection technique for batteryless distributed wearable modules. Two conductive textile layers separated by an insulating fabric layer are used as a garment-wide shared bus that simultaneously conveys DC power and pulse-based data signals without point-to-point wiring. To minimize the circuit overhead of each module, universal asynchronous receiver/transmitter (UART) pulses are directly coupled onto the textile through AC-coupling capacitors without carrier modulation. The textile is modeled as a lumped resistance--capacitance network. The textile waveform is then modeled as the transient response of a second-order circuit. From this model, design conditions for comparator-based waveform recovery and high-bitrate transmission are analytically derived. The resulting design framework determines whether a given combination of data rate, textile capacitance, and resistance is feasible, and also provides the corresponding design range of the decoupling inductors. The required textile parameters are characterized, and robustness to parameter drift is analyzed. These results establish a basic methodology for textile-based simultaneous power and data transfer.

Related papers