Tailoring the properties of YBa 2 Cu 3 O 7-delta thin films by 30-keV He+ irradiation: An enabling route to superconducting device nanopatterning

arXiv:2606.14588 · cond-mat.supr-con, cond-mat.mes-hall, cond-mat.mtrl-sci, physics.app-ph · Submitted 2026-06-12 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Quantum Radio. Generated commentary on the latest quantum physics and condensed matter papers.

Kai: We're looking at the paper: "Tailoring the properties of YBa 2 Cu 3 O 7-delta thin films by 30-keV He+ irradiation".

Mira: Here's the gist of the paper. Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices.

Kai: This work provides a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films.

Mira: Structural Evolution under Irradiation X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating at predominant amorphization at the highest fluence of 1×1016 cm−2.

Kai: The out-of-plane c-axis lattice parameter was observed to increase approximately linearly as a function of ion fluence.

Paper summary: Kai: So we just covered how this paper is setting up a framework for using thirty keV He+ ion irradiation to tune YBCO properties for nanoscale patterning <ref:2606.14588#pg1>.

Mira: They are claiming that by using this ion beam, you can control the electric transport and superconducting properties of these thin films systematically as you increase the ion fluence.

Kai: The core thesis is that this irradiation predominantly introduces disorder in the form of oxygen-related Frenkel defects rather than driving a significant change in oxygen stoichiometry or mobile carrier concentration.

Mira: This is important because it means you can tune the material's behavior without necessarily changing how many charge carriers are available to move around.

Lev: From an error correction standpoint, if the carrier concentration stays stable, that simplifies modeling because you don't have to account for massive changes in doping levels.

Kai: Right, and they show that this has implications for device fabrication by identifying two specific fluence scales: a functional tuning regime up to four times ten to the power of fifteen per square centimeter.

Mira: This regime allows you to continuously adjust the critical temperature Tc, resistivity, and vortex dynamics while keeping the crystallinity mostly intact.

Lev: And beyond that, they identify a threshold at four point five times ten to the power of fifteen per square centimeter where superconductivity gets completely suppressed.

Kai: So it gives engineers a roadmap for when to stop tuning and when you're ready to use these irradiated films as robust barriers for things like Josephson junctions.

Mira: It matters because it provides a controlled route—a way to engineer the properties predominantly through disorder generation—for integrating YBCO into irradiation-defined superconducting electronics.

Lev: So the big picture is that this isn't just about making a material, it's about creating a controllable process for defect engineering in these thin films.

Conclusion: Kai: The paper, titled "Tailoring the properties of YBa2Cu3O7−δ thin films by thirty keV He+ irradiation: An enabling route to superconducting device nanopatterning," is essentially showing how controlled ion irradiation works on these materials <ref:2606.14588#pg1,Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He>.

Mira: It shows that using thirty keV He+ ions isn't just a random way to damage the material; it’s a systematic method for tuning its properties based on the fluence you apply <ref:2606.14588#pg1>.

Kai: The authors, Aichner, Koch, Korner, Karrer and their team at Vienna and Tübingen, provided a comprehensive dataset covering structure and transport measurements.

Mira: The main implication is that this gives researchers a foundation for building predictive defect-engineering protocols when they want to use He-FIB processing in this area.

Lev: So what does that mean practically for someone trying to build actual hardware? It means you can predict the structural outcome based on the ion fluence before you start the expensive fabrication runs.

Kai: Exactly, you can predict where your material will end up structurally and electrically based on how many ions it gets.

Mira: This moves us from just observing effects to having a predictive tool for tailoring these superconducting films for specific device applications.

Lev: It gives you control over the parameters like critical temperature, which is crucial when you're trying to design devices that rely on those exact superconducting properties.

Bernd Aichner, Simon Koch, Philipp A. Korner, Max Karrer, Katja Wurster, Christoph Schmid, Ulrich Kentsch, Reinhold Kleiner, Edward Goldobin, Dieter Koelle and Wolfgang Lang

Faculty of Physics, University of Vienna · Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+ · Ion Beam Center (IBC) | Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf

cond-mat.supr-con, cond-mat.mes-hall, cond-mat.mtrl-sci, physics.app-ph

Submitted: 2026-06-12

Updated: 2026-10-29

Comments: 16 pages, 6 figures, 1 table

Journal ref: Physical Review Applied 26, 044076 (2026)

DOI: 10.1103/7dhm-9tvs

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 53/100

The gist: Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices.

Key concepts

Structural Evolution under Irradiation
X-ray diffraction showed that ion exposure causes a loss of crystalline order in YBCO films. This structural change involves an out-of-plane lattice expansion and a transition from an orthorhombic to a tetragonal structure, leading to amorphization at high fluences.
Defect Characterization via Spectroscopy
Raman spectra analysis indicates that irradiation increases disorder but lacks signs of oxygen depletion. This suggests the primary defects created are oxygen-related Frenkel defects, not changes in the carrier concentration or stoichiometry of the material.
Electronic Transport Tuning
Irradiation increases normal-state resistivity and suppresses the critical temperature (Tc) of superconductivity. The suppression follows Abrikosov–Gor’kov pair breaking, meaning mobile carrier density is unchanged, but superconductivity is quenched at high fluences.

Terminology

Summary

Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices. p. 0

Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

This work provides a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films. p. 0
Where the paper says it

Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films.

Structural Evolution under Irradiation

X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating at predominant amorphization at the highest fluence of 1×1016 cm−2. The out-of-plane c-axis lattice parameter was observed to increase approximately linearly as a function of ion fluence. p. 2

Where the paper says it

0×1015 cm−2 . From the diffraction peak positions, the out-of-plane c-axis lattice parameter was determined and is observed to increase approximately linearly as a function of ion fluence, as shown in Fig.

This expansion is distinct from oxygen depletion, as the electrical transport measurements indicate that irradiation-induced oxygen loss is negligible, instead pointing to enhanced structural disorder. p. 3
Where the paper says it

underlying oxygen depletion versus ion irradiation. As discussed in detail in sections III C and III F, the electrical transport measurements indicate that irradiationinduced oxygen loss is negligible, and instead point to enhanced structural disorder as the primary origin of the observed lattice expansion.

Defect Characterization via Spectroscopy

Raman spectra exhibit increasing disorder while lacking signatures of oxygen depletion, indicating that irradiation mainly generates oxygen-related Frenkel defects rather than changing the carrier concentration. The lack of any detectable 228 cm−1 signal provides strong evidence against significant oxygen depletion during irradiation. p. 4

Where the paper says it

Oxygen-deficient YBCO is characterized by a Raman mode at 228 cm−1 , arising from vibrations of oxygen atoms located at the terminations of disrupted Cu–O chains [38]; this feature is entirely absent in our data. Even considering a possible contribution of the LSAT substrate peak at 148 cm−1 that could influence the detailed line shape of the 144 cm−1 phonon, the lack of any detectable 228 cm−1 signal provides strong evidence against significant oxygen depletion during irradiation.

The enhancement of the background intensity is a generic spectroscopic hallmark of irradiation-induced increase in structural disorder. p. 5
Where the paper says it

Finally, the enhancement of the background intensity evident in Fig. 3(a) represents a generic spectroscopic hallmark of irradiation-induced increase in structural disorder.

Electronic Transport Tuning

Irradiation increases the normal-state resistivity ρN(T) accompanied by a suppression of the critical temperature Tc. The suppression of Tc is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4. p. 0

Where the paper says it

Consistently, with increasing fluence, the normal-state resistivity ρN(T) at temperature T above Tc increases strongly, while ∂ρN/∂T remains nearly unchanged at moderate fluence. The suppression of Tc is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4.

5 × 1015 cm−2. p. 0
Where the paper says it

The suppression of Tc is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4. 5 × 1015 cm−2 .

The normal-state carrier concentration remains essentially unchanged, while the density of mobile carriers is directly connected to the oxygen content. p. 6
Where the paper says it

The negligible variation of the parameter α up to Φ ≤ 3 × 1015 cm−2 indicates that the charge carrier concentration remains essentially unchanged. Furthermore, the density of mobile carriers is directly connected to the oxygen content of YBCO [47], corroborating the interpretation that the suppression of Tc is governed primarily by irradiation-induced defect formation, rather than by oxygen depletion.

Renormalization of Superconducting Parameters

Magnetotransport further demonstrates that irradiation not only reduces Tc but also renormalizes key mixed-state parameters. The upper critical fields extrapolated to T = 0 decrease approximately exponentially with fluence for both B ∥ c and B ∥ ab, with the reduction of Bc c2(0) largely attributable to the suppression of Tc rather than a strong change of dBc2/dT. p. 0

Where the paper says it

5 × 1015 cm−2 . The anisotropic upper critical fields decrease approximately exponentially with increasing fluence, the vortex activation energy is reduced, and the anisotropy drops, in contrast to oxygen-depleted YBCO.

The anisotropy γ = Bab c2(0)/Bc c2(0) is significantly reduced from its pristine value (γ ≈ 6. p. 9
Where the paper says it

5, which is a representative value for YBCO [68]. Upon irradiation, the anisotropy is significantly reduced, as summarized in Table I.

5), opposite to the trend commonly observed in oxygen-depleted YBCO. p. 9
Where the paper says it

The opposite trend emphasizes that distinct microscopic mechanisms govern the suppression of superconductivity in the two cases. In oxygen-depleted samples, the removal of oxygen from the O(1) chain sites weakens the interlayer coupling between the CuO2 planes.

Operational Window Determination

The study establishes two practically important fluence scales for He-FIB nanopatterning: (i) a functional tuning regime up to Φ ∼ 4×10 15 cm−2, where Tc, resistivity, and vortex dynamics are continuously adjustable while crystallinity remains largely intact. (ii) complete suppression of superconductivity at Φ ≳ 4. p. 0

Where the paper says it

Consistently, with increasing fluence, the normal-state resistivity ρN(T) at temperature T above Tc increases strongly, while ∂ρN/∂T remains nearly unchanged at moderate fluence. The suppression of Tc is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4.

p. 0
Where the paper says it

Consistently, with increasing fluence, the normal-state resistivity ρN(T) at temperature T above Tc increases strongly, while ∂ρN/∂T remains nearly unchanged at moderate fluence. The suppression of Tc is accurately described by Abrikosov–Gor’kov pair breaking and reaches complete quenching of superconductivity at 4.

5 × 10 15 cm−2 that enables the formation of robust barriers for, e. p. 2
Where the paper says it

The YBCO unit cell and the conventional notation for the atomic sites are illustrated in Fig. Two fluence values are essential for the design of superconducting devices: on the one hand, the complete suppression of superconductivity enables the creation of barriers in Josephson junctions or pinning sites for Abrikosov vortices.

p. 2
Where the paper says it

The YBCO unit cell and the conventional notation for the atomic sites are illustrated in Fig. Two fluence values are essential for the design of superconducting devices: on the one hand, the complete suppression of superconductivity enables the creation of barriers in Josephson junctions or pinning sites for Abrikosov vortices.

g., Josephson junctions. p. 0
Where the paper says it

In state-of-the-art helium ion microscopes (HIMs) [11, 12], the He-FIB enables the direct fabrication of spatially alternating superconducting and insulating domains, with lateral feature sizes on the order of only a few nanometers. Exploiting this capability, single Josephson junctions (JJs) [8, 9, 13, 14], Josephson diodes [15], JJ arrays [16, 17], superconducting quantum interference devices (SQUIDs) [8, 9, 18], and directional in-plane tunnel spectroscopy [19] have been realized.

p. 0
Where the paper says it

In state-of-the-art helium ion microscopes (HIMs) [11, 12], the He-FIB enables the direct fabrication of spatially alternating superconducting and insulating domains, with lateral feature sizes on the order of only a few nanometers. Exploiting this capability, single Josephson junctions (JJs) [8, 9, 13, 14], Josephson diodes [15], JJ arrays [16, 17], superconducting quantum interference devices (SQUIDs) [8, 9, 18], and directional in-plane tunnel spectroscopy [19] have been realized.

At substantially higher fluence Φ ≳ 8 × 10 15 cm−2, dominant amorphization is expected to compromise spatial resolution and is therefore unfavorable for nanoscale circuit fabrication. p. 2
Where the paper says it

Two fluence values are essential for the design of superconducting devices: on the one hand, the complete suppression of superconductivity enables the creation of barriers in Josephson junctions or pinning sites for Abrikosov vortices. On the other hand, amorphization of the crystalline structure is unfavorable, as amorphous tracks created by He-FIB grow in diameter with increasing numbers of impacting ions [8] and deteriorate the method’s resolution [9].

p. 2
Where the paper says it

Two fluence values are essential for the design of superconducting devices: on the one hand, the complete suppression of superconductivity enables the creation of barriers in Josephson junctions or pinning sites for Abrikosov vortices. On the other hand, amorphization of the crystalline structure is unfavorable, as amorphous tracks created by He-FIB grow in diameter with increasing numbers of impacting ions [8] and deteriorate the method’s resolution [9].

Conclusion

30 keV He+ irradiation provides a controlled route to engineer superconducting and normal-state properties of YBCO thin films predominantly through disorder generation. The quantitative structure–property correlations provide a foundation for predictive defect-engineering protocols and for integrating YBCO into irradiation-defined superconducting electronics. p. 0

Where the paper says it

Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films.

p. 0
Where the paper says it

Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films.

TABLE I is presented on page 12, showing the magnetotransport characteristics of YBCO thin-film microbridges prior to and following irradiation with 30 keV He+ ions. p. 1

Where the paper says it

Two of them (one from each batch) were examined by XRD prior to irradiating all 12 small chips at the Ion-Beam Center of the Helmholtz-Zentrum Dresden-Rossendorf, Germany. Ion irradiation at room temperature was carried out using an ion implanter (Danfysik A/S, Denmark, Model 1050) with He+ ions at an energy of 30 keV and ion fluences Φ in the range from 5×1014 cm−2 to 1×1016 cm−2 , incident orthogonally to the film surface.

The lattice parameter a remains essentially constant while b decreases with fluence, resulting in an orthorhombic-totetragonal transition at Φ ≥ 8 × 10 15 cm−2. p. 3
Where the paper says it

The XRD measurements also enable the determination of the in-plane lattice parameters a and b, which are presented in Fig. While the crystal structure along the a axis exhibits only a marginal expansion with increasing ion fluence, the b lattice parameter decreases, resulting in an orthorhombic-to-tetragonal phase transition at approximately Φ ≈ 8.

This behavior contrasts with observations in oxygen-depleted YBCO single crystals. p. 9
Where the paper says it

Upon irradiation, the anisotropy is significantly reduced, as summarized in Table I. This behavior contrasts with observations in oxygen-deficient YBCO single crystals [69] and thin films [70], where the anisotropy increases as Tc is suppressed.

The low-resistivity segment of the superconducting transition can be described by a thermally activated flux-flow (TAFF) behavior. p. 8
Where the paper says it

In contrast, our measurements indicate that pronounced spatial modulations of ξab(0) are absent in the present samples. The low-resistivity segment of the superconducting transition can be described by a thermally activated flux-flow (TAFF) behavior, ρ(B, T) = ρ0(B) exp [−U0(B)/(kBT)], where U0(B) denotes the activation energy associated with vortex motion and kB is the Boltzmann constant.

This behavior is consistent with a crossover from purely thermally activated flux motion to a vortex-glass regime at higher irradiation levels. p. 8
Where the paper says it

0 × 1015 cm−2 , the resistivity data obey the Arrhenius relation over approximately three decades in ρ. At higher irradiation levels, the low-resistivity tail develops a pronounced positive curvature, which can be attributed to a crossover from purely thermally activated flux motion to a vortex-glass regime [24].

The reduction of U0 up to a fluence of Φ = 3. p. 6
Where the paper says it

5×1015 cm−2 , no signatures of superconductivity are observed down to 2 K. The reduction of Tc,onset with increasing fluence is quantitatively described by the Abrikosov–Gor’kov pairbreaking theory [52].

0 × 10 15 cm−2 is pronounced. p. 0
Where the paper says it

Exploiting this capability, single Josephson junctions (JJs) [8, 9, 13, 14], Josephson diodes [15], JJ arrays [16, 17], superconducting quantum interference devices (SQUIDs) [8, 9, 18], and directional in-plane tunnel spectroscopy [19] have been realized. Furthermore, He-FIB–engineered artificial vortex pinning landscapes in YBCO [20] have recently been shown to sustain pronounced vortex pinning effects up to magnetic fields of 6 T [21], while also exhibiting robust temporal stability over time scales of several years [22].

In conclusion, 30 keV He+ irradiation provides a controlled route to engineer superconducting and normal-state properties of YBCO thin films predominantly through disorder generation. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

The quantitative structure–property correlations provide a foundation for predictive defect-engineering protocols and for integrating YBCO into irradiation-defined superconducting electronics.

--- Page 1 ---

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning

Bernd Aichner, Simon Koch, Philipp A. Korner, Max Karrer, Katja Wurster, Christoph Schmid, Ulrich Kentsch, Reinhold Kleiner, Edward Goldobin, Dieter Koelle and Wolfgang Lang. p. 0

Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices.

I. INTRODUCTION

Nearly four decades after the discovery of copper-oxide high-temperature superconductors [1] and despite extensive experimental and theoretical investigation, the microscopic mechanism underlying high-temperature superconductivity (HTS) remains unresolved. Nevertheless, these materials—most notably the prototypical copperoxide compound YBa2Cu3O7−δ (YBCO)—are now thoroughly characterized and have already been implemented in technological applications. p. 0

Where the paper says it

INTRODUCTION Nearly four decades after the discovery of copper-oxide high-temperature superconductors [1] and despite extensive experimental and theoretical investigation, the microscopic mechanism underlying high-temperature superconductivity (HTS) remains unresolved. Nevertheless, these materials—most notably the prototypical copperoxide compound YBa2Cu3O7−δ (YBCO)—are now thoroughly characterized and have already been implemented in technological applications.

II. METHODS

Thin YBCO films were epitaxially grown on (LaAlO3)0.3(Sr2AlTaO6)0. p. 1

Where the paper says it

METHODS Thin YBCO films were epitaxially grown on (LaAlO3)0. 3(Sr2AlTaO6)0.

7 (LSAT) substrates by pulsed laser deposition (PLD). p. 1
Where the paper says it

3(Sr2AlTaO6)0. 7 (LSAT) substrates by pulsed laser deposition (PLD).

Ion irradiation at room temperature was carried out using an ion implanter with He+ ions at an energy of 30 keV and ion fluences Φ in the range from 5×10 14 cm−2 to 1×10 16 cm−2. p. 1
Where the paper says it

Two of them (one from each batch) were examined by XRD prior to irradiating all 12 small chips at the Ion-Beam Center of the Helmholtz-Zentrum Dresden-Rossendorf, Germany. Ion irradiation at room temperature was carried out using an ion implanter (Danfysik A/S, Denmark, Model 1050) with He+ ions at an energy of 30 keV and ion fluences Φ in the range from 5×1014 cm−2 to 1×1016 cm−2 , incident orthogonally to the film surface.

III. RESULTS AND DISCUSSION

A comparable, nearly linear expansion of the lattice is well established from investigations of oxygen-deficient YBCO. Notably, an O-T phase transition is not necessarily associated with oxygen depletion. p. 4

Where the paper says it

The rearrangement of such CuO chain segments has been proposed as one of the mechanisms underlying persistent photoconductivity in oxygen-deficient YBCO [29], a phenomenon that has indeed also been observed in YBCO irradiated with 75 keV [30] and 80 keV [31] He+ ions. Notably, an O-T phase transition is not necessarily associated with oxygen depletion [32].

The distinction in the present case is that, under ion irradiation, the inplane lattice parameter a ≃ 3. p. 4
Where the paper says it

Notably, an O-T phase transition is not necessarily associated with oxygen depletion [32]. The distinction in the present case is that, under ion irradiation, the inplane lattice parameter a ≃ 3.

84 Å remains essentially invariant, whereas the parameter b exhibits an approximately linear decrease as a function of increasing fluence. p. 4
Where the paper says it

The distinction in the present case is that, under ion irradiation, the inplane lattice parameter a ≃ 3. 84 Å remains essentially invariant, whereas the parameter b exhibits an approximately linear decrease as a function of increasing fluence.

IV. SUMMARY AND CONCLUSIONS

By combining X-ray diffraction, Raman scattering, and comprehensive magneto-transport measurements, we establish a consistent picture in which irradiation predominantly introduces disorder in the form of oxygen-related Frenkel defects rather than driving a significant change of oxygen stoichiometry or mobile carrier concentration. The results delineate two practically important fluence scales: (i) a functional tuning regime up to Φ ∼ 4×10 15 cm−2, where Tc, resistivity, and vortex dynamics are continuously adjustable while crystallinity remains largely intact. (ii) complete suppression of superconductivity at Φ ≳ 4.5 × 10 15 cm−2 that enables the formation of robust barriers for, e.g., Josephson junctions. At substantially higher fluence Φ ≳ 8 × 10 15 cm−2, dominant amorphization is expected to compromise spatial resolution and is therefore unfavorable for nanoscale circuit fabrication.

ACKNOWLEDGEMENTS

P.A.K thanks D. Baurecht for support with the Raman measurements at the Faculty Center for Nanostructure Research at the University of Vienna. p. 0

Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

Parts of this research were carried out at IBC at the Helmholtz-Zentrum Dresden-Rossendorf e. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

V., a member of the Helmholtz Association. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

B.A. acknowledges support from Aktion Österreich-Slowakei, AÖSKInitiativprojektförderung der Aktion (Grant No. 2025-03-15-004), the Federal Ministery of Women, Science and Research of the Republic of Austria and the Ministry of Education, Research, Development and Youth of the Slovak Republic. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

This research was funded in whole, or in part, by the Austrian Science Fund (FWF) Grant-DOI: 10. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

55776/I4865 and by the German Research Foundation (DFG), grants KO 1303/16-1 and Go 1106/7-1. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

REFERENCES

[5] D. Arias, Z. Sefrioui, G. D. Loos, F. Agullo-Rueda, J. Garcia-Barriocanal, C. Leon, and J. Santamaria <ref:2606. p. 0

Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg2>. [6] W. Lang, M. Dineva, M. Marksteiner, T. Enzenhofer, K. Siraj, M. Peruzzi, J. D. Pedarnig, D. Bäuerle, R Korntner <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg2>. [7] R L Gray, M J D Rushton and S T Murphy <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [8] B Müller, M Karrer F Limberger M Becker B Schröppel C J Burkhardt R Kleiner E Goldobin and D Koelle <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [9] C Schmid C Buckreus D Haas M Pröpper R Hutt C Magén D Hanisch M Karrer M Schilling D Koelle R Kleiner and E Goldobin <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [10] I A Zaluzhnyy U Goteti B K Stoychev R Basak E S Lamb E Kisiel T Zhou Z Cai M V Holt J W Beeman E Y Cho S Cybart O G Shpyrko R Dynes and A Frano <ref:2606.14588#pg2>. [11] B W Ward J A Notte and N P Economou <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [12] G Hlawacek and A Gölzhäuser, eds., Helium Ion Microscopy (Springer International Publishing, Switzerland, 2016 <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg4>. [13] S A Cybart E Y Cho T J Wong B H Wehlin M K Ma C Huynh and R C Dynes <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg2>. [14] M Karrer K Wurster J Linek M Meichsner R Kleiner E Goldobin and D Koelle <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [15] C Schmid A Jozani R Kleiner D Koelle and E Goldobin <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [16] J C LeFebvre E Cho H Li K Pratt and S A Cybart <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg2>. [17] M Pröpper D Hanisch C Schmid M Neumann P J Ritter M-A Tucholke E Goldobin D Koelle R Kleiner M Schilling B Hampel <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [18] E Y Cho M K Ma C Huynh K Pratt D N Paulson V N Glyantsev R C Dynes and S A Cybart <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [19] J C LeFebvre E Y Cho and S A Cybart <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [20] B Aichner B Müller M Karrer V R Misko F Limberger K L Mletschnig M Dosmailov J D Pedarnig F Nori R Kleiner D Koelle and W Lang <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [21] M Karrer B Aichner K Wurster C Magén C Schmid R Hutt B Budinská O V Dobrovolskiy R Kleiner W Lang E Goldobin and D Koelle <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg4>. [22] S Keppert B Aichner P Rohringer M-A Bodea B Müller M Karrer R Kleiner E Goldobin D Koelle J D Pedarnig and W Lang <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>. [23] X L Xiao J Haring B Heinz and P Ziemann <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [24] Z Sefrioui D Arias E M González C Léon J Santamaria J L Vicent <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg2>. [25] J F Ziegler M D Ziegler and J P Biersack <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [26] M Tachiki S Takahashi Strong vortex pinning intrinsic in high-Tc oxide superconductors <ref:2606. p. 0
Where the paper says it

These results establish quantitative fluence thresholds and a practical operational window for He-FIB nanopatterning of YBCO quantum circuits. INTRODUCTION Nearly four decades after the discovery of copper-oxide high-temperature superconductors [1] and despite extensive experimental and theoretical investigation, the microscopic mechanism underlying high-temperature superconductivity (HTS) remains unresolved.

14588#pg4>. [27] J D Jorgensen B W Veal A P Paulikas L J Nowicki G W Crabtree H Claus and W K Kwok <ref:2606. p. 0
Where the paper says it

To date, He-FIB nanopatterning has predominantly relied on empirically guided selection of irradiation parameters. However, achieving device-to-device reproducibility necessitates a detailed understanding of the concomitant structural evolution, the superconducting and normalstate transport characteristics, and their correlation with arXiv:2606.

14588#pg4>. [28] J Ye K Nakamura Quantitative structure analyses of YBa2Cu3O7 thin films determination of oxygen content from x-ray-diffraction patterns <ref:2606. p. 0
Where the paper says it

In this work, we provide a comprehensive dataset on the effects of large-area 30 keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7−δ (YBCO) thin films. X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating at predominant amorphization at the highest fluence of 1×1016 cm−2 .

14588#pg4>. [29] W Markowitsch C Stockinger W Göb W Lang W Kula and R Sobolewski Dynamics of photodoping and photoconductivity relaxation in oxygen-deficient YBa2Cu3Ox <ref:2606. p. 4
Where the paper says it

These segments, in turn, lead to an anisotropic modification of the lattice, giving rise to a disproportionate change in the a and b lattice parameters. The rearrangement of such CuO chain segments has been proposed as one of the mechanisms underlying persistent photoconductivity in oxygen-deficient YBCO [29], a phenomenon that has indeed also been observed in YBCO irradiated with 75 keV [30] and 80 keV [31] He+ ions.

14588#pg4>. [30] M A Bodea D Arias Z Sefrioui G Loos M L Lucia J Santamaria F Sanchez-Quesada and M Varela Critical temperature depression and persistent photoconductivity in ion irradiated YBa2Cu3O7−x films and YBa2Cu3O7−x /PrBa2Cu3O7 superlattices <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg4>. [31] X Z Wang B Hellebrand D Bäuerle M Strecker G Wortmann and W Lang Oxygen ordering and superconductivity in GdBaSrCu3O7−x <ref:2606.14588#pg4>. [32] X Z Wang B Hellebrand D Bäuerle M Strecker G Wortmann W Lang Oxygen ordering and superconductivity in GdBaSrCu3O7−x <ref:2606.14588#pg4>. [33] R Carter R Hutt P Zimmermann A Abukaev J Ullmann S Koch C Schmid M Burghammer R Kleiner D Koelle E Goldobin and I A Zaluzhnyy <ref:2606. p. 0
Where the paper says it

Tailoring the properties of YBa2Cu3O7−δ thin films by 30 keV He+ irradiation: An enabling route to superconducting device nanopatterning Bernd Aichner,1, ∗ Simon Koch,2, ∗ Philipp A. Korner,1, ∗ Max Karrer,2 Katja Wurster,2 Christoph Schmid,2 Ulrich Kentsch,3 Reinhold Kleiner,2 Edward Goldobin,2 Dieter Koelle,2 and Wolfgang Lang1, † 1Faculty of Physics, University of Vienna, 1090 Vienna, Austria 2Universität Tübingen, Physikalisches Institut, Center for Quantum Science (CQ) and LISA+, Tübingen, 72076, Germany 3 Ion Beam Center (IBC) | 712/306, Institute of Ion Beam Physics and Materials Research, Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Dresden, 01328, Germany Focused helium ion beam (He-FIB) irradiation with 30 keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation.

14588#pg2>.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved material design prediction for superconducting circuits using ion irradiation parameters by correlating fluence with critical temperature suppression via Abrikosov–Gor’kov pair breaking theory. This allows AI systems to predict the necessary He+ ion fluence to achieve a target Tc suppression level for device patterning or pinning site engineering.

  2. Enhanced structural defect characterization of YBa2Cu3O7-delta thin films by using Raman spectroscopy as a sensitive probe for oxygen Frenkel defects, specifically by monitoring the absence of the 228 cm-1 mode. This enables AI systems to distinguish between disorder caused by oxygen depletion and disorder caused by irradiation-induced point defects.

  3. Predictive modeling of superconducting device performance under magnetic fields by incorporating fluence-dependent changes in upper critical fields (Bc c2(0)) and vortex activation energy (U0) into magnetotransport simulations. This allows AI systems to accurately estimate the field-induced suppression of Tc and vortex dynamics for patterned YBCO structures before physical fabrication.

  4. Real-time optimization of ion beam processing parameters for He-FIB nanopatterning by using quantitative thresholds derived from resistivity changes and lattice parameter shifts. This enables AI systems to dynamically adjust ion fluence in real time to maintain a desired balance between superconducting suppression and minimal structural degradation, targeting the operational window of 1x1016 cm-2.

  5. Automated analysis of Hall effect data for mobile carrier concentration estimation by applying the Anderson semi-empirical relation cot theta H = alpha H T squared + beta H. This allows AI systems to infer whether observed changes in Hall coefficient are due to charge carrier concentration changes or enhanced defect scattering, providing a more robust understanding of the underlying electronic transport mechanisms.

Abstract

Focused helium ion beam (He-FIB) irradiation with 30-keV ions is a key tool for nanoscale patterning and defect engineering in high transition temperature (Tc) cuprate superconducting devices, yet its usable fluence window is constrained by the competing requirements of reliable superconductivity suppression and minimal structural degradation. In this work, we provide a comprehensive dataset on the effects of large-area 30-keV He+ ion exposure on the electric transport and superconducting properties of epitaxial YBa2Cu3O7 (YBCO) thin films. X-ray diffraction shows a fluence-driven loss of crystalline order accompanied by an out-of-plane lattice expansion and an orthorhombic-to-tetragonal transition, culminating in predominant amorphization at the highest fluence of 1 x 10 16 cm-2. Raman spectra exhibit increasing disorder while lacking signatures of oxygen depletion, indicating that irradiation mainly generates oxygen-related Frenkel defects rather than changing the carrier concentration. Consistently, with increasing fluence, the normal-state resistivity ρ N(T) at temperature T above Tc increases strongly, while d ρ N/d T remains nearly unchanged at moderate fluence. The suppression of Tc is accurately described by Abrikosov-Gor'kov pair breaking and reaches complete quenching of superconductivity at 4.5 x 10 15 cm-2. The anisotropic upper critical fields decrease approximately exponentially with increasing fluence, the vortex activation energy is reduced, and the anisotropy drops, in contrast to oxygen-depleted YBCO. Hall-angle analysis confirms a nearly constant carrier density but a systematic increase in defect scattering and reduced mobility, consistent with a crossover toward the dirty limit at high fluence. These results establish quantitative fluence thresholds and a practical operational window for He-FIB nanopatterning of YBCO quantum circuits.

Sources

Related papers