Ultrashort Two-Pulse Train Generation on a 100 TW Laser Beamline Using a Delay Mask After the Final Focusing Optics

arXiv:2606.13183 · physics.plasm-ph · Submitted 2026-06-11 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Ultrashort Two-Pulse Train Generation on a 100 TW Laser Beamline Using a Delay Mask After the Final Focusing Optics".

Mira: Here's the gist of the paper. Experimental results aimed at demonstrating the feasibility of a two-section delay mask for the generation of ultrashort pulse trains are reported The presented pulse-train generation scheme, developed at the Intense Laser Irradiation Laboratory (ILIL)

12: , takes advantage of wavefront division using a thin transparent plate, a so-called delay mask

13, 14, 15: This method is particularly attractive for ReMPI-driven laser wakefield acceleration because it can generate pulse trains with controllable delays and balanced intensities Feasibility Demonstration The experiment was carried out at the CNR-INO Intense Laser Irradiation Laboratory using a 240 TW laser system operated at 120 TW, as part of the ongoing preparation for the first experimental demonstration of ReMPI The delay mask is deliberately positioned downstream of the OAP mirror, constituting a fundamentally novel implementation of the technique that has not been previously demonstrated and enables direct manipulation of the beam already under the influence of focusing optics Transverse Profile Characterization To determine the appropriate dimensions of the delay mask and its individual sections, it was necessary to characterize the transverse fluence distribution of the laser beam at the exact position where the mask will be inserted into the beam path The RCFs were irradiated with a single laser shot under high-power conditions corresponding to the ∼ 120 TW operational regime, delivering ∼ 2.2 J per pulse before spatial filtering Assuming a homogeneous transverse fluence distribution, the theoretical fluence right after the spatial filter was estimated to be approximately ϕTheo = 138 mJ/cm2 The reconstructed mean fluence under high-power operating conditions was found to be ϕ¯ = 115.6 ± 11.8 mJ/cm2, which closely matches the theoretical estimate Mask Design and Verification The primary objective of these simulations was to determine the optimal geometry of the delay mask annular sections, specifically their corresponding areas, such that each section contributed equally to the peak intensity in the focal plane The resulting focal-plane intensity distributions produced by the individual delay mask sections were measured in a low-power setting using non-transparent spatial masks with geometries identical to those of the actual delay mask A comparison between the simulated and experimentally measured focal-plane distributions shows good agreement, confirming that the fabricated delay mask geometry closely fulfills the intended beam-splitting and focal-intensity balancing conditions Temporal Performance The expected, theoretical pulse-to-pulse delay given by Equation 8, where L = 500 ± 100 µm and vg = 206283945.5 m/s is ∆tT heo = 907.2 fs The experimentally measured pulse-to-pulse delay corresponds to ∆tT heo, and no significant pulse elongation due to propagation through the material was observed These results confirm that the proposed delay-mask configuration is capable of producing temporally delayed laser pulses with balanced peak intensities in the focal plane while preserving the ultrashort pulse duration required for the first experimental proof-of-concept of the ReMPI scheme In this work, a methodology for the design and experimental validation of a delay mask for potential use in the ReMPI scheme was presented The retrieved fluence distribution was subsequently fitted using super-Gaussian function and employed as input for numerical simulations of the focal-plane intensity distribution produced by the off-axis parabolic mirror The measured focal spots and corresponding beam waist values showed good agreement with the simulation results, confirming the validity of the proposed mask design Finally, temporal characterization of the generated pulse pair demonstrated a pulse-topulse delay consistent with the theoretical prediction derived from the fused silica thickness and group velocity The results confirm that the proposed delay-mask configuration is capable of producing temporally delayed laser pulses with balanced peak intensities in the focal plane while preserving the ultrashort pulse duration required for the first experimental proof-of-concept of the ReMPI scheme REFERENCES

1: D.

Kai: Umstadter, E.

Mira: Esarey, and J.

Kai: Kim.

Paper summary: Kai: So looking at this paper's title and what we've discussed, "Ultrashort Two-Pulse Train Generation on a one hundred TW Laser Beamline Using a Delay Mask After the Final Focusing Optics," it really highlights how focused they are on this specific beam manipulation technique <ref:2606.13183#pg1,Laser Beamline Using a Delay Mask After the Final Focusing Optics>.

Mira: The authors are basically presenting a methodology for designing and experimentally validating this delay mask setup specifically for potential use in the resonant multi-pulse ionization injection scheme. They've shown that they can achieve both temporal delay control and intensity balancing using a two-section mask after the final focusing optics.

Lev: What this means for us is that we have a validated concept here—a proof of principle demonstration—that shows how to use this geometry to manipulate the beam structure before it hits the final stages of acceleration or interaction. It gives us something concrete to work with when designing future high-power laser systems.

Kai: And while they confirm the temporal delay matches theory based on their fused silica thickness and group velocity, we need to remember that they explicitly state that this mask configuration does not yet provide pulse-to-pulse delays optimized for ReMPI operation at practically relevant plasma densities.

Mira: Exactly, so the implication is that this work is a necessary first step. It proves the concept works in a controlled setting, but future work will need to address those specific density requirements to make it ready for actual experimental physics involving plasma interactions.

Lev: I think the real value here is in mapping out how these optical elements interact with the existing focusing optics, which is something that needs careful attention when we move from simulation to building actual hardware. It’s about integrating this into a larger system architecture.

Conclusion: Kai: So this paper is about setting up a two section delay mask after the final focusing optics to make ultrashort pulse trains on a hundred terawatt laser beamline at an intense laser irradiation laboratory at the cnri ino.

Mira: I see, so they're essentially testing if you can use that thin transparent plate to control how the pulses are spaced out and keep their peak intensities even after they've been focused by the mirror.

Lev: From my side, it sounds like a really precise way to manage the spatial distribution right before the beam hits whatever is downstream, which would be crucial for any real accelerator setup.

Kai: Yeah, they measured the temporal delay and it actually matched what their math predicted based on how thick the plate was and how fast light travels through that specific material.

Mira: That's important because if the timing doesn't match theory, then you can't trust it to generate those precise intervals needed for things like resonant multi-pulse ionization injection.

Lev: But they also noted there wasn't any noticeable pulse stretching from the material itself, which is good news for us because that means the pulse duration stays ultrashort.

Kai: So the implication is that this delay mask configuration can actually work to produce those temporally delayed pulses with balanced peak intensities while keeping them short enough for our experimental proof-of-concept.

Mira: It confirms the methodology they developed is valid for use in a resonant multi-pulse scheme, but it's just a proof of concept at this stage, so you still have to push those intensity requirements later.

Lev: Right, so it proves the physical mechanism works under these conditions and we can start designing how to integrate that geometry into actual hardware.

Kai: Exactly, and that opens up the door to figuring out how much control we really have over the pulse train structure in those high-power regimes.

Intense Laser Irradiation Laboratory CNR-National Institute of Optics Department of Physics University of Pisa Istituto Nazionale di Fisica Nucleare INFN Pisa ELI Beamlines Facility The Extreme Light Infrastructure ERIC

physics.plasm-ph

Submitted: 2026-06-11

Updated: 2026-11-12

DOI: 10.1016/j.optcom.2026.133968

License: http://creativecommons.org/licenses/by-nc-nd/4.0/

Importance score: 76/100

The gist: Experimental results aimed at demonstrating the feasibility of a two-section delay mask for the generation of ultrashort pulse trains are reported The presented pulse-train generation scheme…

Key concepts

Delay Mask
A thin transparent plate used to divide a laser beam into sections. This method creates different time delays between pulses by splitting the beam, allowing for precise control over when subsequent pulses arrive at the focal point.
ReMPI-driven Laser Wakefield Acceleration
This is a technique where a laser pulse train drives an intense plasma wave. The use of a delay mask allows for balanced intensities across multiple pulses in this process, which is crucial for generating high-quality electron bunches.
Transverse Fluence Distribution Characterization
This involves measuring how the laser beam's energy is spread out across its width at the point where it enters the mask. By characterizing this distribution, researchers could design the mask sections to ensure each part contributes equally to the final peak intensity.

Terminology

Summary

Experimental results aimed at demonstrating the feasibility of a two-section delay mask for the generation of ultrashort pulse trains are reported The presented pulse-train generation scheme, developed at the Intense Laser Irradiation Laboratory (ILIL) [12], takes advantage of wavefront division using a thin transparent plate, a so-called delay mask [13, 14, 15] This method is particularly attractive for ReMPI-driven laser wakefield acceleration because it can generate pulse trains with controllable delays and balanced intensities

Feasibility Demonstration

The experiment was carried out at the CNR-INO Intense Laser Irradiation Laboratory using a 240 TW laser system operated at 120 TW, as part of the ongoing preparation for the first experimental demonstration of ReMPI The delay mask is deliberately positioned downstream of the OAP mirror, constituting a fundamentally novel implementation of the technique that has not been previously demonstrated and enables direct manipulation of the beam already under the influence of focusing optics

Transverse Profile Characterization

To determine the appropriate dimensions of the delay mask and its individual sections, it was necessary to characterize the transverse fluence distribution of the laser beam at the exact position where the mask will be inserted into the beam path The RCFs were irradiated with a single laser shot under high-power conditions corresponding to the ∼ 120 TW operational regime, delivering ∼ 2.2 J per pulse before spatial filtering Assuming a homogeneous transverse fluence distribution, the theoretical fluence right after the spatial filter was estimated to be approximately ϕTheo = 138 mJ/cm2 The reconstructed mean fluence under high-power operating conditions was found to be ϕ¯ = 115. p. 4

Where the paper says it

2 J per pulse before spatial filtering, conservatively accounting for transmission losses introduced by the beam transport optics and, predominantly, by the final compressor stage of the chirped pulse amplification [20] system. Assuming a homogeneous transverse fluence distribution, the theoretical fluence right after the spatial filter was estimated to be approximately ϕTheo = 138 mJ/cm2 .

6 ± 11.8 mJ/cm2, which closely matches the theoretical estimate

Mask Design and Verification

The primary objective of these simulations was to determine the optimal geometry of the delay mask annular sections, specifically their corresponding areas, such that each section contributed equally to the peak intensity in the focal plane The resulting focal-plane intensity distributions produced by the individual delay mask sections were measured in a low-power setting using non-transparent spatial masks with geometries identical to those of the actual delay mask A comparison between the simulated and experimentally measured focal-plane distributions shows good agreement, confirming that the fabricated delay mask geometry closely fulfills the intended beam-splitting and focal-intensity balancing conditions

Temporal Performance

The expected, theoretical pulse-to-pulse delay given by Equation 8, where L = 500 ± 100 µm and vg = 206283945.5 m/s is ∆tT heo = 907. p. 6

Where the paper says it

The expected, theoretical pulse-to-pulse delay given by Equation 8, where L = 500 ± 100 µm and vg = 206283945. 5 m/s is ∆tT heo = 907.

2 fs The experimentally measured pulse-to-pulse delay corresponds to ∆tT heo, and no significant pulse elongation due to propagation through the material was observed These results confirm that the proposed delay-mask configuration is capable of producing temporally delayed laser pulses with balanced peak intensities in the focal plane while preserving the ultrashort pulse duration required for the first experimental proof-of-concept of the ReMPI scheme

Conclusion

In this work, a methodology for the design and experimental validation of a delay mask for potential use in the ReMPI scheme was presented The retrieved fluence distribution was subsequently fitted using super-Gaussian function and employed as input for numerical simulations of the focal-plane intensity distribution produced by the off-axis parabolic mirror The measured focal spots and corresponding beam waist values showed good agreement with the simulation results, confirming the validity of the proposed mask design Finally, temporal characterization of the generated pulse pair demonstrated a pulse-topulse delay consistent with the theoretical prediction derived from the fused silica thickness and group velocity The results confirm that the proposed delay-mask configuration is capable of producing temporally delayed laser pulses with balanced peak intensities in the focal plane while preserving the ultrashort pulse duration required for the first experimental proof-of-concept of the ReMPI scheme

REFERENCES

[1] D. Umstadter, E. p. 8

Where the paper says it

References [1] D. Umstadter, E.

Esarey, and J. p. 8
Where the paper says it

Umstadter, E. Esarey, and J.

Kim. “Nonlinear Plasma Waves Resonantly Driven by Optimized Laser Pulse Trains”. p. 8
Where the paper says it

Esarey, and J. “Nonlinear Plasma Waves Resonantly Driven by Optimized Laser Pulse Trains”.

In: Physical Review Letters 72. p. 8
Where the paper says it

“Nonlinear Plasma Waves Resonantly Driven by Optimized Laser Pulse Trains”. In: Physical Review Letters 72.

8 (1994), pp. p. 8
Where the paper says it

In: Physical Review Letters 72. 8 (1994), pp.

1224–1227

[2] P. Tomassini et al. p. 8

Where the paper says it

1103/PhysRevLett. Tomassini et al.

p. 8
Where the paper says it

1103/PhysRevLett. Tomassini et al.

p. 8
Where the paper says it

1103/PhysRevLett. Tomassini et al.

p. 8
Where the paper says it

1103/PhysRevLett. Tomassini et al.

“The resonant multi-pulse ionization injection”. p. 0
Where the paper says it

Introduction The generation of controlled laser pulse trains is a crucial technological step toward advanced laser-driven acceleration concepts. In particular, the pulse-train generation scheme presented here is intended to enable the Resonant Multi-Pulse Ionization Injection (ReMPI) scheme [1, 2, 3, 4].

In: Physics of Plasmas 24. p. 8
Where the paper says it

“The resonant multi-pulse ionization injection”. In: Physics of Plasmas 24.

10 (2017), p. p. 8
Where the paper says it

In: Physics of Plasmas 24. 10 (2017), p.

103220

[3] P. Tomassini et al. “High-quality GeV-scale electron bunches with the Resonant MultiPulse Ionization Injection”. p. 8

Where the paper says it

Tomassini et al. “High-quality GeV-scale electron bunches with the Resonant MultiPulse Ionization Injection”.

In: Nuclear Instruments and Methods in Physics Research Section A 909 (2018), pp. p. 8
Where the paper says it

“High-quality GeV-scale electron bunches with the Resonant MultiPulse Ionization Injection”. In: Nuclear Instruments and Methods in Physics Research Section A 909 (2018), pp.

1–4

[4] P. Tomassini et al. “High-quality 5 GeV electron bunches with resonant multi-pulse ionization injection”. p. 8

Where the paper says it

Tomassini et al. “High-quality 5 GeV electron bunches with resonant multi-pulse ionization injection”.

In: Plasma Physics and Controlled Fusion 62. p. 8
Where the paper says it

“High-quality 5 GeV electron bunches with resonant multi-pulse ionization injection”. In: Plasma Physics and Controlled Fusion 62.

2 (2020), p. p. 8
Where the paper says it

In: Plasma Physics and Controlled Fusion 62. 2 (2020), p.

014010

[5] P. Tomassini et al. “Ultra-high-brightness and tuneable attosecond-long electron beams with the laser wake field acceleration”. p. 8

Where the paper says it

Tomassini et al. “Ultra-high-brightness and tuneable attosecond-long electron beams with the laser wake field acceleration”.

In: Scientific Reports 15 (2025), p. p. 8
Where the paper says it

“Ultra-high-brightness and tuneable attosecond-long electron beams with the laser wake field acceleration”. In: Scientific Reports 15 (2025), p.

40794

[6] R. W. Assmann, M. p. 8

Where the paper says it

1038/s41598-025-24672-7. Assmann, M.

K. Weikum, T. Akhter, et al. p. 8
Where the paper says it

Assmann, M. Akhter, et al.

“EuPRAXIA Conceptual Design Report”. p. 8
Where the paper says it

Akhter, et al. “EuPRAXIA Conceptual Design Report”.

In: The European Physical Journal Special Topics 229. p. 8
Where the paper says it

“EuPRAXIA Conceptual Design Report”. In: The European Physical Journal Special Topics 229.

24 (2020), pp. p. 8
Where the paper says it

In: Plasma Physics and Controlled Fusion 62. 2 (2020), p.

3675–4284

[7] A. M. Weiner, J. P. Heritage, and E. p. 8

Where the paper says it

1140/epjst/e2020-000127-8. Heritage, and E.

M. Kirschner. “High-resolution femtosecond pulse shaping”. p. 8
Where the paper says it

Heritage, and E. “High-resolution femtosecond pulse shaping”.

In: J. Opt. Soc. Am. B 5 (1988), pp: 1563–1572

[8] C. W. Siders et al. p. 8

Where the paper says it

1364/JOSAB. Siders et al.

“Efficient high-energy pulse-train generation using a 2n-pulse Michelson interferometer”. p. 8
Where the paper says it

Siders et al. “Efficient high-energy pulse-train generation using a 2n-pulse Michelson interferometer”.

In: Applied Optics 37. p. 8
Where the paper says it

“Efficient high-energy pulse-train generation using a 2n-pulse Michelson interferometer”. In: Applied Optics 37.

22 (1998), pp: 5302–5305

[9] R.J. Shalloo et al. p. 8

Where the paper says it

5302–5305. Shalloo et al.

“Generation of laser pulse trains for tests of multi-pulse laser wakefield acceleration”. p. 8
Where the paper says it

Shalloo et al. “Generation of laser pulse trains for tests of multi-pulse laser wakefield acceleration”.

In: Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment 829 (2016), 2nd European Advanced Accelerator Concepts Workshop - EAAC 2015, pp: 383–385

[10] B. Dromey et al. p. 8

Where the paper says it

doi: https://doi. Dromey et al.

“Generation of a train of ultrashort pulses from a compact birefringent crystal array”. p. 8
Where the paper says it

Dromey et al. “Generation of a train of ultrashort pulses from a compact birefringent crystal array”.

In: Applied Optics 46. p. 8
Where the paper says it

“Efficient high-energy pulse-train generation using a 2n-pulse Michelson interferometer”. In: Applied Optics 37.

22 (2007), pp: 5142–5146

[11] T. Robinson et al. p. 8

Where the paper says it

5142–5146. Robinson et al.

“Simple technique for generating trains of ultrashort pulses”. p. 8
Where the paper says it

Robinson et al. “Simple technique for generating trains of ultrashort pulses”.

In: Optics Letters 32. p. 8
Where the paper says it

“Simple technique for generating trains of ultrashort pulses”. In: Optics Letters 32.

15 (2007), pp: 2203–2205

[12] L. A. Gizzi et al. p. 8

Where the paper says it

2203–2205. Gizzi et al.

“Overview and specifications of laser and target areas at the Intense Laser Irradiation Laboratory”. p. 8
Where the paper says it

Gizzi et al. “Overview and specifications of laser and target areas at the Intense Laser Irradiation Laboratory”.

In: High Power Laser Science and Engineering 9 (2021), e10

[13] G. Vantaggiato et al. p. 8

Where the paper says it

In: High Power Laser Science and Engineering 9 (2021), e10. Vantaggiato et al.

“Modelling of pulse train generation for resonant laser wakefield acceleration using a delay mask”. p. 8
Where the paper says it

Vantaggiato et al. “Modelling of pulse train generation for resonant laser wakefield acceleration using a delay mask”.

In: Nuclear Instruments and Methods in Physics Research Section A 909 (2018), pp: 114–117

[14] A. Marasciulli et al. p. 8

Where the paper says it

In: Nuclear Instruments and Methods in Physics Research Section A 909 (2018), pp. Marasciulli et al.

p. 8
Where the paper says it

In: Nuclear Instruments and Methods in Physics Research Section A 909 (2018), pp. Marasciulli et al.

“A study of ultrashort pulse train generated via tailored transparent delay mask”. p. 8
Where the paper says it

Marasciulli et al. “A study of ultrashort pulse train generated via tailored transparent delay mask”.

In: Conference on Lasers and Electro-Optics. p. 8
Where the paper says it

“A study of ultrashort pulse train generated via tailored transparent delay mask”. In: Conference on Lasers and Electro-Optics.

2021, SW3Q. p. 8
Where the paper says it

In: Conference on Lasers and Electro-Optics. 2021, SW3Q.

3

[15] A. Marasciulli et al. “Signatures of resonantly driven laser-wakefield excitation by a pulse train generated by an optical delay mask”. p. 9

Where the paper says it

Marasciulli et al. “Signatures of resonantly driven laser-wakefield excitation by a pulse train generated by an optical delay mask”.

In: Applied Optics 62 (2023), pp: 9368–9374

[16] Y. He et al. “Measuring fluence distribution of intense short laser based on the radiochromic effect”. p. 9

Where the paper says it

9368–9374. “Measuring fluence distribution of intense short laser based on the radiochromic effect”.

In: Optics Letters 46 (2021), pp: 2795–2798

[17] J. A. Stratton and L. p. 2

Where the paper says it

Here, the optical path p (x) between the point x, y, ad2 OAD + z ′ on the reference plane and the point x, y, a x 2 + y 2 on the OAP surface SOAP was introduced, while angle δ accounts for different polarization directions. Given the system geometry, depicted in Figure 1, and presented conditions, the diffraction integrals based on the full Stratton-Chu vector theory [17] and previous, recent studies [18, 19] are given as E Re j (xp, t) = − 1 λ Z SOAP A(x, y) × h Im n g (Ej ) o cos (kv − ωt) + Re n g (Ej ) o sin (kv − ωt) i dx dy, (6) E Im j (xp, t) = − 1 λ Z SOAP A(x, y) × h Im n g (Ej ) o sin (kv − ωt) − Re n g (Ej ) o cos (kv − ωt) i dx dy, and are capable of describing the electric fields of a laser pulse focused by an OAP mirror.

J. Chu. “Diffraction Theory of Electromagnetic Waves”. p. 9
Where the paper says it

Stratton and L. “Diffraction Theory of Electromagnetic Waves”.

In: Physical Review 56 (1 1939), pp: 99–107

[18] L. Labate et al. p. 0

Where the paper says it

gregocki@ino. labate@ino.

“Effects of small misalignments on the intensity and Strehl ratio for a laser beam focused by an off-axis parabola”. p. 9
Where the paper says it

Labate et al. “Effects of small misalignments on the intensity and Strehl ratio for a laser beam focused by an off-axis parabola”.

In: Applied Optics 55 (23 2016), pp: 6506–6515

[19] L. Labate, G. Vantaggiato, and L. p. 8

Where the paper says it

In: High Power Laser Science and Engineering 9 (2021), e10. Vantaggiato et al.

A. Gizzi. “Intra-cycle depolarization of ultraintense laser pulses focused by off-axis parabolic mirrors”. p. 9
Where the paper says it

Vantaggiato, and L. “Intra-cycle depolarization of ultraintense laser pulses focused by off-axis parabolic mirrors”.

In: High Power Laser Science and Engineering 6 (2018), e32

[20] D. Strickland and G. p. 9

Where the paper says it

In: High Power Laser Science and Engineering 6 (2018), e32. Strickland and G.

Mourou. “Compression of amplified chirped optical pulses”. p. 9
Where the paper says it

Strickland and G. “Compression of amplified chirped optical pulses”.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Automated design optimization for delay masks using super-Gaussian function fitting can be implemented to determine optimal geometries for equal peak intensities in focal plane simulations. This allows AI systems to automatically calculate section areas, such as A1 = 2.68 cm2 and A2 = 8.22 cm2, based on experimentally retrieved transverse fluence distributions.

  2. Enhanced beam profile reconstruction capabilities can be achieved by integrating EBT4 radiochromic film data processing with super-Gaussian fitting to accurately determine parameters like FWHM, standard deviation sigma x, sigma y, and super-Gaussian order n from raw netOD values. This improves the fidelity of the input for subsequent numerical simulations of the focal plane intensity distribution.

  3. Predictive modeling for pulse train characteristics can be developed by using the theoretical pulse-to-pulse delay formula Delta t = L / vg - 1/c to predict experimental results based on material thickness and group velocity. The AI system can then compare these predictions against measured second-order auto-correlation traces, as shown in Figure 7, to validate the mask design.

  4. A closed-loop feedback mechanism can be designed where the simulated focal spot distributions are compared directly with experimentally retrieved focal spots to confirm the validity of the fabricated delay mask geometry. This ensures that individual sections block or transmit regions accurately, confirming that the fabricated delay mask geometry closely fulfills the intended beam-splitting and focal-intensity balancing conditions.

Abstract

Experimental results showing the generation of an ultrashort two-pulse train using a two-section delay mask placed downstream of the off-axis parabola focusing optics are reported. Based on the initial simulation results, a circular fused silica plate with a central aperture and a measured thickness of 570 plus or minus50 μ m used in the quantitative delay calculation was designed to enable two distinct transverse portions of the incident laser pulse to be focused, ideally, with equal intensity. This fulfills one of the requirements of the resonant multi-pulse ionization injection (ReMPI) scheme for laser wakefield acceleration. As an intermediary step, a calibration of Gafchromic EBT4 films against laser fluence was established, enabling direct characterization of the unattenuated transverse beam profile. The experiment was carried out at the CNR-INO Intense Laser Irradiation Laboratory (ILIL) using a 240 TW laser system operated at 100 TW as part of the ongoing preparation for the first experimental demonstration of ReMPI. The pulse-to-pulse delay introduced by the delay mask was experimentally measured (at a reduced power, as customary for temporal autocorrelation measurements) to be 901 fs, in good agreement with the expected value of 888 fs. While the pulse-to-pulse delay is not yet optimized for ReMPI operation at practically relevant plasma densities, the experimental results demonstrate the feasibility of the proposed delay-mask concept.

Related papers