Modeling and Force Analysis of a Soft Linear Pneumatic Actuator

arXiv:2605.21836 · cs.RO · Submitted 2026-05-21 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: We're looking at the paper: "Modeling and Force Analysis of a Soft Linear Pneumatic Actuator".

Dev: Here's the gist of the paper. Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

Rosa: This paper presents an analytical and experimental force analysis of a linear soft sleeve actuator (LSSA).

Dev: The results show that LSSA force generation is governed by coupled effects of pressure, geometry, displacement, loading, and axial stiffness.

Rosa: Analytical Model Development A quasi-static analytical model was developed by expressing the net axial force as the pressure-generated contribution from the cap and folded walls, reduced by the force associated with axial stiffness.

Paper summary: Rosa: So, looking at the paper "Modeling and Force Analysis of a Soft Linear Pneumatic Actuator," the main thing we learned is that the performance of this actuator isn't constant; it depends heavily on how much you extend it and what kind of external force is applied.

Dev: The authors developed an analytical and experimental force analysis for the linear soft sleeve actuator, showing that its force generation is governed by a combination of pressure, geometry, displacement, loading, and axial stiffness.

Taro: What this means in simple terms is that you need to model how these factors couple together because you can't just look at one variable in isolation when designing something like this.

Rosa: The paper tackles the challenge of understanding why the force drops as it extends and how external static loading changes that pressure response, which helps designers figure out the right operating range.

Dev: The authors used a quasi-static analytical model that expresses the net axial force as a pressure-generated contribution from the cap and folded walls reduced by the force associated with axial stiffness.

Taro: It also highlights how tuning that axial stiffness is key, because it’s not about making it completely soft, but finding that right balance where wall integrity is still maintained.

Rosa: Ultimately, for anyone interested in assistive robotics or wearable tech using these soft sleeve actuators, this work provides a framework to predict the force output before you even build the thing.

Dev: It gives us a clearer understanding of the displacement-dependent force analysis and how external loads modify that pressure response across various pressure ranges.

Conclusion: Rosa: So we've looked at this paper about modeling and force analysis of a linear soft pneumatic actuator.

Dev: Right, it's all about figuring out how this soft sleeve thing actually pushes and what happens when you stretch it out or hit it with an outside load.

Rosa: The authors, Abboodi and Doumit, they are really focused on that coupling between the pressure inside and the physical shape of the sleeve.

Dev: Yeah, they developed this analytical model where they take that total force—the net axial force—and break it down into how much pressure is pushing versus how much stiffness resists it.

Rosa: It shows clearly that as you extend this actuator, the generated force just drops continuously until it basically hits zero at the end of its stroke.

Dev: That displacement dependence is key, and they also found that adding an external static load messes with everything; it delays when you actually start seeing force generation and cuts the output down across most pressure settings.

Rosa: It really highlights that for these soft actuators, you can't just focus on the internal pressure alone; geometry and stiffness are just as much part of the story.

Dev: Exactly, because if we only tune the material to be super soft, we run into problems with wall integrity during those extension cycles.

Rosa: So what does this mean for wearable systems? It means designers need to account for that stiffness tuning when they plan how far and how hard they want their robot arm or assistive device to move.

Dev: It also points toward the future work, which is building a numerical model of the sleeve actuator to see if those analytical predictions match up with what an actual computer simulation would show.

Rosa: That's a big step, moving from just an equation on paper to something that can actually predict real-world performance under stress.

University of Ottawa

cs.RO

Submitted: 2026-05-21

Updated: 2026-11-11

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 74/100

The gist: Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

Key concepts

Linear Soft Sleeve Actuator (LSSA)
A pneumatic device made from a soft sleeve structure used for actuation. The researchers analyzed how this actuator generates force by considering internal pressure and the physical shape of the sleeve walls. They found that its performance is not just about pressure but also how stiff the material is.
Analytical Model
A mathematical framework developed to predict the LSSA's force output without needing constant physical testing. This model combines factors like internal pressure, wall geometry, displacement, and axial stiffness into an equation (Fy = ∑ (F1 + F2y − F3y) − FK) to show how the force changes.
External Static Loading
The effect of an outside weight applied to the actuator while it is being tested. The experiment showed that adding a static load, such as 3.5 kg, delayed when measurable force started appearing and lowered the total force generated across different pressure settings.

Terminology

Summary

Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems. p. 0

Where the paper says it

1 Analytical and Experimental Force Analysis of a Soft Linear Pneumatic Actuator By Mohammed Abboodi mabbo103@uottawa. ca Abstract Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

This paper presents an analytical and experimental force analysis of a linear soft sleeve actuator (LSSA). p. 0
Where the paper says it

However, the force-generation behavior of SSAs remains insufficiently explained, particularly with respect to the variation of output force during extension, the influence of external loading, and the mechanical role of axial stiffness. This paper presents an analytical and experimental force analysis of a linear soft sleeve actuator (LSSA).

The results show that LSSA force generation is governed by coupled effects of pressure, geometry, displacement, loading, and axial stiffness. p. 0
Where the paper says it

Static loading delayed measurable force generation and reduced force output, particularly at low and intermediate pressures. The results show that LSSA force generation is governed by coupled effects of pressure, geometry, displacement, loading, and axial stiffness.

Analytical Model Development

A quasi-static analytical model was developed by expressing the net axial force as the pressure-generated contribution from the cap and folded walls, reduced by the force associated with axial stiffness. This model incorporates internal pressure, projected pressure areas, folded wall geometry, axial displacement, and an experimentally fitted axial stiffness relation. p. 0

Where the paper says it

A quasi-static analytical model was developed by expressing the net axial force as the pressure-generated contribution from the cap and folded walls, reduced by the force associated with axial stiffness. The model incorporates internal pressure, projected pressure areas, folded wall geometry, axial displacement, and an experimentally fitted axial stiffness relation.

The force balance is expressed as Fy = ∑ (F1 + F2y − F3y) − FK. p. 4
Where the paper says it

At equilibrium, the actuator output force is determined by the pressure-induced forces acting on the cap and folded walls, reduced by the force associated with the axial stiffness of the actuator. The force balance is expressed as Where 𝐹1 is the force generated by the cap, 𝐹2𝑦 is the axial component of the force generated by the external wall, 𝐹3𝑦 is the axial component of the force generated by the internal wall, and 𝐹𝐾 is the force associated with the axial stiffness of the actuator.

The pressure-induced force components are calculated from the internal pressure and the corresponding projected areas. p. 4
Where the paper says it

3(a), and the detailed wall geometry is shown in Fig. The pressure-induced force components are calculated from the internal pressure and the corresponding projected areas: where 𝐴1 , 𝐴2 , and 𝐴3are the projected areas of the cap, external wall, and internal wall, respectively.

Experimental Material Characterization

Thermoplastic polyurethane with a Shore hardness of 85A (TPU 85, NinjaTek, USA) was used to fabricate the soft actuator. Tensile testing was performed using an Instron universal testing machine (Model 4202) until approximately 660% elongation. p. 1

Where the paper says it

Tensile testing was performed using an Instron universal testing machine (Model 4202), as shown in Fig. Each specimen was stretched under ambient conditions at a constant crosshead speed of 100 mm/min until approximately 660% elongation.

The five-parameter Mooney–Rivlin model provided the most stable and accurate fit to the TPU 85 data. p. 2
Where the paper says it

3 Mooney–Rivlin, Yeoh, Ogden, and Arruda–Boyce models. Among these models, the five-parameter Mooney–Rivlin model provided the most stable and accurate fit to the TPU 85 data.

Force Response During Extension

The LSSA generated its maximum force at the initial position, with an output of approximately 112 N at zero extension. As the extension increased, the generated force decreased continuously, reaching approximately 72 N at 10 mm, 41 N at 20 mm, and 19 N at 30 mm. p. 5

Where the paper says it

The LSSA generated its maximum force at the initial position, with an output of approximately 112 N at zero extension. As the extension increased, the generated force decreased continuously, reaching Figure 4: Axial stiffness polynomial model 𝐹𝐾𝑎𝑐𝑡𝑢𝑎𝑡𝑜𝑟 = 𝑎 𝑦 3 + 𝑏 𝑦 2 + 𝑐 𝑦 +𝑑 (9) 𝐹𝐾𝑎𝑐𝑡𝑢𝑎𝑡𝑜𝑟 = 4.

At approximately 40 mm of extension, the generated force approached zero. p. 6
Where the paper says it

7 approximately 72 N at 10 mm, 41 N at 20 mm, and 19 N at 30 mm. At approximately 40 mm of extension, the generated force approached zero, indicating that the actuator had reached its effective extension limit under the tested pressure condition.

Influence of External Loading

The effect of external static loading on LSSA force generation was evaluated using the static-load setup described in Section 2.2. The largest reduction was observed under the 3. p. 6

Where the paper says it

The 2 kg load produced a greater reduction in force at low and intermediate pressures; however, its response became closer to the lower-load cases at higher pressures. The largest reduction was observed under the 3.

5 kg load, where the measured force remained near zero until approximately 60–70 kPa. p. 6
Where the paper says it

5 kg load. In this case, the measured force remained near zero until approximately 60–70 kPa, after which it increased steadily with pressure and reached approximately 130 N at 200 kPa.

This response shows that higher external loads delayed the onset of measurable force generation and reduced the force output over all the tested pressure range. p. 6
Where the paper says it

In this case, the measured force remained near zero until approximately 60–70 kPa, after which it increased steadily with pressure and reached approximately 130 N at 200 kPa. This response shows that higher external loads delayed the onset of measurable force generation and reduced the force output over all the tested pressure range.

Design Implications and Limitations

The analytical model clarifies why the actuator force decreases during extension, why the force approaches zero near the end of its stroke, and how external static loading modifies the force–pressure response. The design challenge is therefore not to minimize stiffness completely, but to tune it. p. 7

Where the paper says it

Increasing the effective projected area can improve force generation, but excessive axial stiffness reduces the net force available for external work. The design challenge is therefore not to minimize stiffness completely, but to tune it.

The material and fabrication process also influence this balance, as wall integrity depends on melt flow, interlayer bonding, and airtightness. p. 7
Where the paper says it

However, actuator performance is determined by the printed TPU structure rather than by the filament material alone. In fused deposition modeling, wall integrity depends on melt flow, interlayer bonding, wall continuity, dimensional accuracy, and airtightness.

Future work will focus on developing a numerical model of the LSSA and comparing its predictions with the analytical model and experimental results. p. 8
Where the paper says it

The analytical model provides a basis for interpreting this force response and for refining future LSSA designs through improved control of geometry, axial stiffness, and polymer processing conditions. Future work will focus on developing a numerical model of the LSSA and comparing its predictions with the analytical model and experimental results.

Conclusion

The LSSA force output is displacement-dependent. The available force decreases as the actuator approaches its effective extension limit. p. 8

Where the paper says it

The experimental results confirmed that the LSSA force output is displacement-dependent. At 125 kPa, the generated force decreased from approximately 112 N at zero extension to nearly zero at 40 mm, showing that the available force decreases as the actuator approaches its effective extension limit.

Static-load testing further showed that external loading reduces the available force and delays measurable force generation, particularly at low and intermediate pressures. p. 8
Where the paper says it

At 125 kPa, the generated force decreased from approximately 112 N at zero extension to nearly zero at 40 mm, showing that the available force decreases as the actuator approaches its effective extension limit. Static-load testing further showed that external loading reduces the available force and delays measurable force generation, particularly at low and intermediate pressures.

These findings demonstrate that LSSA force generation is governed by the coupled effects of internal pressure, folded wall geometry, axial displacement, external loading, axial stiffness, and the mechanical behavior of the printed TPU structure. p. 8
Where the paper says it

Static-load testing further showed that external loading reduces the available force and delays measurable force generation, particularly at low and intermediate pressures. These findings demonstrate that LSSA force generation is governed by the coupled effects of internal pressure, folded wall geometry, axial displacement, external loading, axial stiffness, and the mechanical behavior of the printed TPU structure.

REFERENCES

[1] M. Abboodi, “Soft Pneumatic Actuators for Soft Robotics: A Motion-Based Review of Actuation Mechanisms and Performance Trade-offs,” May 2026, doi: 10. p. 8

Where the paper says it

References [1] M. Abboodi, “Soft Pneumatic Actuators for Soft Robotics: A Motion-Based Review of Actuation Mechanisms and Performance Trade-offs,” May 2026, doi: 10.

2139/ssrn.6647558.

[2] M. S. Xavier et al. p. 8

Where the paper says it

Abboodi, “Soft Pneumatic Actuators for Soft Robotics: A Motion-Based Review of Actuation Mechanisms and Performance Trade-offs,” May 2026, doi: 10. Xavier et al.

p. 8
Where the paper says it

Abboodi, “Soft Pneumatic Actuators for Soft Robotics: A Motion-Based Review of Actuation Mechanisms and Performance Trade-offs,” May 2026, doi: 10. Xavier et al.

, “Soft Pneumatic Actuators: A Review of Design, Fabrication, Modeling, Sensing, Control and Applications,” IEEE Access, vol. p. 8
Where the paper says it

Xavier et al. , “Soft Pneumatic Actuators: A Review of Design, Fabrication, Modeling, Sensing, Control and Applications,” IEEE Access, vol.

10, pp. 59442–59485. p. 8
Where the paper says it

, “Soft Pneumatic Actuators: A Review of Design, Fabrication, Modeling, Sensing, Control and Applications,” IEEE Access, vol. 59442–59485, 2022, doi: 10.

[3] C. Thalman and P. p. 8

Where the paper says it

1109/ACCESS. Thalman and P.

Artemiadis, “A review of soft wearable robots that provide active assistance: Trends, common actuation methods, fabrication, and applications,” Wearable Technologies, vol. p. 8
Where the paper says it

Thalman and P. Artemiadis, “A review of soft wearable robots that provide active assistance: Trends, common actuation methods, fabrication, and applications,” Wearable Technologies, vol.

1, p. e3.

[4] M. Abboodi and M. p. 0

Where the paper says it

1 Analytical and Experimental Force Analysis of a Soft Linear Pneumatic Actuator By Mohammed Abboodi mabbo103@uottawa. ca Abstract Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

p. 0
Where the paper says it

1 Analytical and Experimental Force Analysis of a Soft Linear Pneumatic Actuator By Mohammed Abboodi mabbo103@uottawa. ca Abstract Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

p. 0
Where the paper says it

1 Analytical and Experimental Force Analysis of a Soft Linear Pneumatic Actuator By Mohammed Abboodi mabbo103@uottawa. ca Abstract Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems.

Doumit, “Twisting Soft Sleeve Actuator: Design and Experimental Evaluation,” Electronics (Basel). p. 8
Where the paper says it

Abboodi and M. Doumit, “Twisting Soft Sleeve Actuator: Design and Experimental Evaluation,” Electronics (Basel).

, vol. 14, no. 20, p. 4020.

[5] M. Abboodi and M. Doumit, “Design, Manufacturing, and Testing of a Novel Omnidirectional Soft Sleeve Actuator,” Sci. p. 8

Where the paper says it

Abboodi and M. Doumit, “Design, Manufacturing, and Testing of a Novel Omnidirectional Soft Sleeve Actuator,” Sci.

Rep., 2026.

[6] A. Dana, S. Vollach, and D. p. 8

Where the paper says it

Doumit, “Design, Manufacturing, and Testing of a Novel Omnidirectional Soft Sleeve Actuator,” Sci. Vollach, and D.

Shilo, “Use the Force: Review of High-Rate Actuation of Shape Memory Alloys,” Actuators, vol. p. 8
Where the paper says it

Vollach, and D. Shilo, “Use the Force: Review of High-Rate Actuation of Shape Memory Alloys,” Actuators, vol.

10, no. 7, p. 140.

[7] A. Lizotte and A. p. 8

Where the paper says it

3390/act10070140. Lizotte and A.

L. Trejos, “Active cooling of twisted coiled actuators via fabric air channels,” Frontiers in Rehabilitation Sciences, vol. p. 8
Where the paper says it

Lizotte and A. Trejos, “Active cooling of twisted coiled actuators via fabric air channels,” Frontiers in Rehabilitation Sciences, vol.

3, Nov. 2022.

[8] M. Abboodi and M. Doumit, “Development and Testing of Novel Soft Sleeve Actuators,” IEEE Access, vol. p. 8

Where the paper says it

Abboodi and M. Doumit, “Development and Testing of Novel Soft Sleeve Actuators,” IEEE Access, vol.

12, pp. 39995–40010. p. 8
Where the paper says it

Doumit, “Development and Testing of Novel Soft Sleeve Actuators,” IEEE Access, vol. 39995–40010, 2024, doi: 10.

[9] W. Jung, Y. Kang, S. Han, and Y. p. 8

Where the paper says it

1109/ACCESS. Han, and Y.

Hwang, “Biocompatible micro, soft bellow actuator rapidly manufactured using 3D-printed soluble mold,” Journal of Micromechanics and Microengineering, vol. p. 8
Where the paper says it

Han, and Y. Hwang, “Biocompatible micro, soft bellow actuator rapidly manufactured using 3D-printed soluble mold,” Journal of Micromechanics

29, no. 12.

[10] C. Tawk, G. M. Spinks, M. In Het Panhuis, and G. p. 9

Where the paper says it

1088/1361-6439/ab477f. In Het Panhuis, and G.

Alici, “3D Printable Linear Soft Vacuum Actuators: Their Modeling, Performance Quantification and Application in Soft Robotic Systems,” IEEE/ASME Transactions on Mechatronics, vol. p. 9
Where the paper says it

In Het Panhuis, and G. Alici, “3D Printable Linear Soft Vacuum Actuators: Their Modeling, Performance Quantification and Application in Soft Robotic Systems,” IEEE/ASME Transactions on Mechatronics, vol.

24, no. 5.

[11] Z. Wang et al. p. 9

Where the paper says it

1109/TMECH. Wang et al.

p. 9
Where the paper says it

1109/TMECH. Wang et al.

, “A Soft Robotic Hand Based on Bellows Actuators for Dishwashing Automation,” IEEE Robot Autom Lett, vol. p. 9
Where the paper says it

Wang et al. , “A Soft Robotic Hand Based on Bellows Actuators for Dishwashing Automation,” IEEE Robot Autom Lett, vol.

6, no. 2.

[12] Y. Dang, J. Chen, and J. p. 9

Where the paper says it

2021, doi: 10. Chen, and J.

Han, “Preliminary Design and Performance Test of an Origami Actuator Inspired by Yoshimura Pattern,” in 2021 27th International Conference on Mechatronics and Machine Vision in Practice (M2VIP), 2021. p. 9
Where the paper says it

Chen, and J. Han, “Preliminary Design and Performance Test of an Origami Actuator Inspired by Yoshimura Pattern,” in 2021 27th International Conference on Mechatronics and Machine Vision in Practice (M2VIP), 2021, pp.

[13] L. Paez, G. Agarwal, and J. p. 9

Where the paper says it

1109/M2VIP49856. Agarwal, and J.

Paik, “Design and Analysis of a Soft Pneumatic Actuator with Origami Shell Reinforcement,” Soft Robot, vol. p. 9
Where the paper says it

Agarwal, and J. Paik, “Design and Analysis of a Soft Pneumatic Actuator with Origami Shell Reinforcement,” Soft Robot, vol.

3, no. 3.

[14] S. Wang et al., “Design of deployable circular structures based on Miura origami pattern,” Mech Mach Theory, vol. p. 9

Where the paper says it

Li, and R. Liu, “Design of deployable circular structures based on Miura origami pattern,” Mech Mach Theory, vol.

186, Aug. 2023.

[15] A. Pagoli, F. Chapelle, J. p. 9

Where the paper says it

mechmachtheory. Chapelle, J.

A. Corrales-Ramon, Y. p. 9
Where the paper says it

Chapelle, J. Corrales-Ramon, Y.

Mezouar, and Y. p. 9
Where the paper says it

Corrales-Ramon, Y. Mezouar, and Y.

Lapusta, “Review of soft fluidic actuators: Classification and materials modeling analysis,” Jan 01, 2022. p. 9
Where the paper says it

Lapusta, “Review of soft fluidic actuators: Classification and materials modeling analysis,” Jan. 01, 2022, IOP Publishing Ltd.

[16] J. Walker et al. p. 9

Where the paper says it

1088/1361- 665X/ac383a. Walker et al.

, “Soft robotics: A review of recent developments of pneumatic soft actuators,” Actuators, vol. p. 9
Where the paper says it

Walker et al. , “Soft robotics: A review of recent developments of pneumatic soft actuators,” Actuators, vol.

9, no. 1.

[17] P. Polygerinos et al. p. 9

Where the paper says it

3390/act9010003. Polygerinos et al.

, “Towards a soft pneumatic glove for hand rehabilitation,” in IEEE International Conference on Intelligent Robots and Systems, 2013. p. 9
Where the paper says it

Polygerinos et al. , “Towards a soft pneumatic glove for hand rehabilitation,” in IEEE International Conference on Intelligent Robots and Systems, 2013, pp.

[18] M. S. Xavier et al., “Soft Pneumatic Actuators: A Review of Design, Fabrication, Modeling, Sensing, Control and Applications,” 2022. p. 8

Where the paper says it

, “Soft Pneumatic Actuators: A Review of Design, Fabrication, Modeling, Sensing, Control and Applications,” IEEE Access, vol. 59442–59485, 2022, doi: 10.

[19] N. El-Atab et al. p. 9

Where the paper says it

1109/ACCESS. El-Atab et al.

, “Soft Actuators for Soft Robotic Applications: A Review,” Advanced Intelligent Systems, vol. p. 9
Where the paper says it

El-Atab et al. , “Soft Actuators for Soft Robotic Applications: A Review,” Advanced Intelligent Systems, vol.

2, no. 10.

[20] M. Moutousi and P. p. 9

Where the paper says it

2020, doi: 10. Moutousi and P.

Polygerinos, “Omnidirectional soft pneumatic actuators: a design and optimization framework,” Front Robot AI, vol. p. 9
Where the paper says it

Moutousi and P. Polygerinos, “Omnidirectional soft pneumatic actuators: a design and optimization framework,” Front Robot AI, vol.

11, Sep. 2024.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Improved force generation prediction for soft pneumatic actuators by incorporating a quasi-static analytical model that expresses net axial force as the pressure-generated contribution from the cap and folded walls, reduced by the force associated with axial stiffness. This allows AI systems to accurately predict how output force decreases during extension and how external loading modifies the pressure response.

  2. Enhanced actuator design optimization capabilities for linear soft sleeve actuators (LSSA) by using the analytical model to clarify why the actuator force decreases during extension, why the force approaches zero near the effective extension limit, and how external static loading modifies the force–pressure response. This enables AI to tune geometry and axial stiffness for better useful force over a required displacement range.

  3. Better material and fabrication process control for soft robotics by linking processing parameters like extrusion temperature, print speed, flow rate, and layer height directly to the analytical model's variables. This allows AI systems to predict how defects such as leakage or weak interlayer bonding reduce the effective pressure available for actuation before physical testing.

Abstract

Soft sleeve actuators (SSAs) have recently been developed as a pneumatic actuation approach for wearable and assistive robotic systems. By integrating the actuation structure into a sleeve-like geometry, these actuators can reduce reliance on external attachment layers and transmission mechanisms while maintaining compliance with limb-shaped surfaces. However, the force-generation behavior of SSAs remains insufficiently explained, particularly with respect to the variation of output force during extension, the influence of external loading, and the mechanical role of axial stiffness. This paper presents an analytical and experimental force analysis of a linear soft sleeve actuator (LSSA). A quasi-static analytical model was developed by expressing the net axial force as the pressure-generated contribution from the cap and folded walls, reduced by the force associated with axial stiffness. The model incorporates internal pressure, projected pressure areas, folded wall geometry, axial displacement, and an experimentally fitted axial stiffness relation. Prescribed-extension and static-load experiments were conducted to evaluate the actuator response. At 125 kPa, the generated force decreased from approximately 112 N at zero extension to nearly zero at 40 mm. Static loading delayed measurable force generation and reduced force output, particularly at low and intermediate pressures. The results show that LSSA force generation is governed by coupled effects of pressure, geometry, displacement, loading, and axial stiffness.

Related papers