Radial-Component Predominant-Mode Inversion of Rayleigh Waves: Application to DAS-based Site Characterization
Listen
Radio episode about this paper
Transcript
Introduction to the show: ident: Physics. The day in general physics: instruments, methods and results across the field.
Kai: We're looking at the paper: "Radial-Component Predominant-Mode Inversion of Rayleigh Waves".
Paper summary: Kai: So, to recap, this paper is about using a component-consistent approach for DAS-based surface wave measurements. The authors are saying that when you activate a vertical source along the fiber, DAS only measures the radial component of Rayleigh wave motion >
Mira: And conventional techniques, like Multichannel Analysis of Surface Waves or MASW, primarily measure the vertical component. So those dispersion data sets can actually be different because the radial component and vertical component might exhibit fundamentally different modal behaviors due to ellipticity >
Lev: So that difference becomes more pronounced in complicated subsurface settings like when you have strong velocity contrasts or layers with low-velocity layers or high-velocity layers >
Kai: Precisely. The paper points out that these differences become especially noticeable in complex stratigraphic conditions, and because of things like embedded high velocity layers and strong velocity contrasts, the dispersion spectrum might show smooth transitions between modes >
Mira: And those smooth transitions make mode identification and indexing really challenging for analysts when they are looking at the data >
Lev: That brings us to their main point: they use this RCPM framework to solve that problem by focusing on matching measured radial component dispersion trends with the theoretical mode having the maximum modal amplitude >
Conclusion: Kai: So, looking at the full picture, this work by Mrinal Bhaumik and Brady R Cox is about improving how we use distributed acoustic sensing for site characterization using surface waves >
Mira: The implication is that by adopting this component-consistent inversion strategy, we can get more reliable estimates of subsurface shear wave velocity profiles when using DAS data >
Lev: What this means practically is that we reduce the ambiguity in modal identification, which leads to better results for those Vs estimates compared to methods where an analyst has to do all the work manually >
Kai: The paper shows that this approach actually performs better than conventional multi-modal approaches when you look at some subsurface conditions because it has less scatter in the shear wave velocity misfit values >
Mira: It also validated their method using field data from two different sites, showing good agreement with independent invasive measurements like cone penetration test and borehole data >
Lev: So, to sum up, the RCPM framework offers a fundamentally improved way to interpret dispersion data from DAS by cutting down on guesswork in mode identification and providing more stable estimates of the subsurface shear wave velocity profiles >
Mrinal Bhaumik, Brady R. Cox
Utah State University
physics.geo-ph, cs.SD
Submitted: 2026-05-16
Updated: 2026-05-16
Journal ref: Journal of Geophysical Research: Solid Earth, Vol. 131, Issue 10, October 2026, e2026JB034811
DOI: 10.1029/2026JB034811
License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/
Importance score: 79/100
The gist: Radial-Component Predominant-Mode Inversion of Rayleigh Waves: Application to DAS-based Site Characterization presents a radial-component predominant-mode (RCPM) inversion framework designed for…
Key concepts
- Radial-Component Predominant-Mode Inversion (RCPM)
- A technique that analyzes DAS measurements by focusing on the radial component of Rayleigh waves. It identifies the specific wave mode that has the largest amplitude at each frequency, rather than relying on manual mode selection. This approach simplifies interpretation and reduces reliance on subjective analyst judgment.
- Vertical vs. Radial Component Dispersion
- Dispersion data derived from vertical geophones often differs significantly from data extracted from DAS, especially in complex geology. This difference arises because the radial component of Rayleigh waves can exhibit different modal behaviors due to wave ellipticity, meaning they may not always match the behavior observed in vertical measurements.
- Transfer Matrix Method (TLM)
- A mathematical tool used in this framework to solve the forward problem of wave propagation. It treats the wave equation as an eigenvalue problem, allowing researchers to simultaneously calculate both the modal wavenumbers and their corresponding mode shapes efficiently.
Terminology
Summary
Radial-Component Predominant-Mode Inversion of Rayleigh Waves: Application to DAS-based Site Characterization presents a radial-component predominant-mode (RCPM) inversion framework designed for DAS-based surface-wave measurements that explicitly accounts for the sensitivity of the Rayleigh wave radial component under a vertical source configuration The proposed RCPM approach eliminates the need for explicit modal indexing, provides a componentconsistent interpretation of radial-component dispersion data, and substantially reduces reliance on subjective analyst-driven modal interpretations
Problem Statement
Conventional surface-wave techniques primarily utilize the vertical component of Rayleigh wave motion Dispersion data extracted from radial-component waveforms can differ from dispersion data extracted from vertical-component waveforms, especially in complex stratigraphic conditions. Distributed Acoustic Sensing (DAS) measurements predominantly capture the radial component of Rayleigh wave motion when a surface source is activated along the fiber. p. 1 However, because DAS is only capable of measuring radial motions, one should not expect dispersion data extracted from DAS waveforms to always agree well with dispersion data extracted from vertical geophones. p. 1 The radial component of Rayleigh waves may exhibit fundamentally different modal behavior compared to the vertical component due to ellipticity. p. 2
RCPM Methodology
The proposed RCPM framework focuses on matching measured dominantamplitude radial dispersion trends with the theoretical mode exhibiting the maximum modal amplitude. This approach is implemented using a transfer matrix method (TLM) which formulates the forward problem as an eigenvalue problem, facilitating simultaneous computation of modal wavenumbers and mode shapes. p. 3 The predominant mode for the vertical-source with radial-receiver (V–R) configuration is obtained from the product of the vertical and horizontal modal amplitudes. p. 4 This formulation is conceptually different from an effective or superimposed mode formulation because it identifies the mode with the highest modal participation at each frequency. p. 5
Synthetic Model Evaluation
The study systematically evaluates the RCPM approach using three synthetic ground models and two field DAS datasets. The synthetic results demonstrate that modal energy distribution differs significantly between vertical and radial components in the presence of strong velocity contrasts, low-velocity layers, and high-velocity layers. p. 0 The proposed RCPM method consistently captures the correct modal response and yields stable and reliable shear wave velocity (Vs) profiles across different inversion parameterizations. p. 0
Inversion Performance Comparison
The proposed RCPM framework was compared with a conventional multi-modal (CMM) approach where mode indexing must be assigned manually by the analyst. The results demonstrate that for some subsurface conditions the CMM approaches can yield ambiguous interpretations due to challenges in radial component mode identification. p. 3 In contrast, the proposed RCPM framework provides more consistent and physically meaningful results by incorporating radial component modal energy into the inversion process. p. 3 The RCPM inversion demonstrates improved performance relative to the CMM inversions, as it has the lesser amount of scatter in the Vs misfit values and its lowest dispersion misfit models have lower Vs misfit values compared to CMM for all LR parameterizations. p. 2
Field Data Validation
The methodology is further validated using two field DAS datasets, where the inverted Vs profiles show good agreement with independent invasive measurements, including cone penetration test and borehole data. For Site A, the inverted Vs profiles consistently identify a high Vs layer interface at a depth of approximately 13. p. 55–15 m, which is in good agreement with the location of this shale layer indicated by borehole data. p. 0 For Site B, the inverted Vs profiles indicate a stiff near-surface layer followed by a thick, very-low velocity layer extending to approximately 8 m depth, which is consistent with the interpreted lithology from a borehole near the tower. p. 5
Conclusion
The findings emphasize the importance of adopting component-consistent forward modeling and inversion strategies for DAS-based surface-wave analysis. The proposed RCPM framework offers a fundamentally improved approach for interpreting dispersion data extracted from DAS waveform measurements by reducing ambiguity in modal identification, enhancing inversion stability, and providing more reliable estimates of subsurface Vs profiles. p. 0 This approach successfully captures key subsurface features, including soft near-surface layers and deeper velocity contrasts, and shows good agreement with available invasive measurements. p. 0
References
Ajo-Franklin et al. 2019. “Distributed Acoustic Sensing Using ark Fiber for Near-Surface Characterization and Broadband Seismic Event detection. p. 1” Scientific Reports 2019 9:1, 9 (1): 1328-. p. 1 https://doi.org/10.1038/s41598-018-36675-8
Aki and Richards 2002. Quantitative Seismology. Quse. 2nd ed. Mill Valley, California.: University Science Books
Astaneh and Guddati 2015. “Efficient computation of dispersion curves for multilayered waveguides and half-spaces. p. 3” Computer Methods in Applied Mechanics and Engineering, 300: 27–46. p. 1 North-Holland. https://doi.org/10.1016/J.CMA.2015.11.019
Barbosa and Kausel 2012. “The thin-layer method in a cross-anisotropic space. p. 3” International Journal for Numerical Methods in Engineering, 89 (5): 537–560. p. 1 https://doi.org/10.1002/nme.3246
Bhaumik and Naskar 2024a. “Higher-order thin layer method as an efficient forward model for calculating dispersion curves of surface and Lamb waves in layered media. p. 3” Computers and Geosciences, 186: 105570. https://doi.org/10.1016/j.cageo.2024.105570
Bhaumik and Naskar 202b. “Computation of Surface Wave’s dominating Mode For Stratified Media. p. 1” Indian Geotechnical Journal, 1–16. p. 2 Springer. https://doi.org/10.1007/s40098-024-01045-x
Bhaumik and Naskar 2c. “Active Sourced Wavefield Modeling for Layered Half-Space. p. 3” Journal of Geotechnical and Geoenvironmental Engineering, 150 (11): 04024111. p. 0 American Society of Civil Engineers. p. 0 p. 0 https://doi.org/10.6092/polito/porto/2497212
Boaga et al. 2013. “Mode misidentification in Rayleigh waves: Ellipticity as a cause and a cure. p. 2” Geophysics, 78 (4): EN17–EN28. https://doi.org/10.1190/geo2012-0194
ox and Beekman 2011. “ntramethod ariability in eMi ispersion Measurements and s Estimates at Shallow Bedrock Sites.” Journal of Geotechnical and Geoenvironmental Engineering, 137 (4): 354–362. p. 0 American Society of Civil Engineers. https://doi.org/10.1061/(asce)gt.1943-5606.0000436
ox and Teague 201. “Layering ratios: A systematic approach to the inversion of surface wave data in the absence of a priori information. p. 5” Geophysical Journal International, 207 (1): 422–438. Oxford Academic. https://doi.org/10.1093/gji/ggw282
Dal Moro 2015. Surface Wave Analysis for Near Surface Applications. p. 5 p. 5 Surface Wave Analysis for Near Surface Applications. Elsevier
al Moro 2020. “The magnifying effect of a thin shallow stiff layer on Love waves as revealed by multi-component analysis of surface waves. p. 8” Scientific Reports, 10 (1): 9071. https://doi.org/10.1038/s41598-020-66070-1
Dal Moro et al. 2017. “Improved Holistic Analysis of Rayleigh Waves for Single- and Multi-Offset Data: Joint Inversion of Rayleigh-Wave Particle Motion and Verticaland Radial-omponent elocity Spectra. p. 1” Pure and Applied Geophysics 2017 175:1, 175 (1): 67–88. p. 1 Springer. https://doi.org/10.1007/S00024-017-1694-8
Daley et al. 2022. “Field testing of fiber-optic distributed acoustic sensing (AS) for subsurface seismic monitoring. p. 0” The Leading Edge, 32 (6): 699–706. p. 5 GeoScienceWorld. https://doi.org/10.1190/TLE32060699
Foti 2000. “Multistation Methods for Geotechnical characterization using Surface Waves. p. 1” Politecnico di Torino. Politecnico di Torino. https://doi.org/10.6092/polito/porto/2497212
Hubbard et al. 2022. “Quantifying the Surface Strain Field Induced by Active Sources with Distributed Acoustic Sensing: Theory and Practice. p. 1” Sensors, 22 (12): 4589. p. 1 MDPI AG. https://doi.org/10.1016/j.sensors.
Jiang et al. p. 2 2023. “Distributed acoustic sensing for shallow structure imaging using mechanical noise: A case study in Guangzhou, hina. p. 0” Journal of Applied Geophysics, 215: 105139. p. 2 Elsevier. https://doi.org/10.1016/J.JAPPGEO.
Kausel 2024a. p. 3 “ynamic point sources in laminated media via the thin-layer method. p. 3” International Journal of Solids and Structures, 36 (31–32): 4725–4742. https://doi.org/10.1016/S0020-7683(98)00262-5
Kausel and Peek 1982. “ynamic loads in the interior of a layered stratum: An explicit solution. p. 3” Bulletin of the Seismological Society of America, 72 (5): 1459–1481. GeoScienceWorld. https://doi.org/10.1785/BSSA0720051459
Kausel and Peek 201. “Stiffness matrices for layered soils. p. 3” Bulletin of the Seismological Society of America, 71 (6): 1743–1761. https://doi.org/10.1785/BSSA071006
Kramer 1996. Geotechnical earthquake engineering. p. 0 Upper Saddle River, NJ: Upper Saddle River, NJ:Prentice-Hall
Lai 199. “Simultaneous inversion of Rayleigh phase velocity and attenuation for near-surface site characterization. p. 0” Georgia nstitute of Technology, Atlanta, Georgia. p. 0
Lancelle et al. p. 2 2021. “Using istributed Acoustic Sensing (AS) for Multichannel Analysis of Surface Waves (MASW). p. 0” Distributed Acoustic Sensing in Geophysics: Methods and Applications, 213–228. p. 0 wiley. https://doi.org/10.1080/24705314.
Luo et al. 2020. “Horizontally orthogonal distributed acoustic sensing array for earthquake- and ambient-noise-based multichannel analysis of surface waves. p. 0” Geophysical Journal International, 222 (3): 2147–2161. Oxford Academic. https://doi.org/10.1093/GJI/GGAA293
Nazarian et al. 1983. “Use of spectral analysis of surface waves method for determination of moduli and thicknesses of pavement systems. p. 0” Transportation Research Record, 38–45
O’Neill and Matsuoka 2005. “ominant Higher Surface-wave Modes and Possible Inversion Pitfalls. p. 3” Journal of Environmental and Engineering Geophysics, 10 (2): 185–201. p. 0 https://doi.org/10.2113/JEEG10.2.185
Okada 2003. The Microtremor Survey Method. p. 1 Society of Exploration Geophysicists
Panthi and ox 202. “omparative Analysis of Strain-to-Velocity Conversion Methods for Active-source DAS Data and Co-located Nodal Stations. p. 0” Sensors (Submitted). p. 1
Park et al. p. 1 1999. “Multichannel analysis of surface waves. p. 0” Geophysics, 64 (3): 800–808. Soc of Exploration Geophysicists. https://doi.org/10.1190/1.1444590
oshdy et al. 2025. “Application of istributed Acoustic Sensing for Active Near-Surface Seismic Monitoring. p. 0” Sensors 2025, Vol. p. 2 25, Page 1558, 25 (5): 1558. Multidisciplinary Digital Publishing Institute. https://doi.org/10.3390/S25051558
ossi et al. 2022. “Assessment of istributed Acoustic Sensing (AS) performance for geotechnical applications. p. 0” Engineering Geology, 306: 106729. p. 0 Elsevier. https://doi.org/10.1016/J.ENGGEO.2022.106729
Shragge et al. 2021. “Low-frequency ambient distributed acoustic sensing (AS): case study from Perth, Australia. p. 0” Geophysical Journal International, 226 (1): 564–581. Oxford Academic. https://doi.org/10.1093/GJI/GGAB111
Soga and Luo 2018. “istributed fiber optics sensors for civil engineering infrastructure sensing. p. 0” Journal of Structural Integrity and Maintenance, 3 (1): 1–21. Taylor and Francis Ltd. https://doi.org/10.1080/24705314
Stokoe et al. 2020. “NHE @UTexas Experimental Facility With Large-Scale Mobile Shakers for Field Studies. p. 8” Frontiers in Built Environment, 6: 575973. Frontiers Media S. p. 1A. https://doi.org/10.3389/FBUIL.2020.575973/TEXT
Storn and Price 1997. “ifferential Evolution - A Simple and Efficient Heuristic for Global Optimization over ontinuous Spaces. p. 2” Journal of Global Optimization, 11 (4): 341–359. p. 2 Springer Netherlands. https://doi.org/10.1023/A:1008202821328
Trafford and Long 2020. “elationship between Shear-Wave Velocity and Undrained Shear Strength of Peat. p. 0” Journal of Geotechnical and Geoenvironmental Engineering, 146 (7). p. 0 American Society of Civil Engineers (ASCE). p. 0 p. 0 https://doi.org/10.1061/(ASCE)GT.1943-5606.0002298
antassel and ox 2021. “SWinvert: A workflow for performing rigorous 1-D surface wave inversions. p. 2” Geophysical Journal International, 224 (2): 1141–1156. Oxford University Press. p. 0 https://doi.org/10.93/gji/ggaa426
antassel and ox 2022. “SWprocess: a workflow for developing robust estimates of surface wave dispersion uncertainty. p. 9” Journal of Seismology, 26 (4): 731–756. Springer Science and Business Media B. p. 1V. https://doi.org/10.1007/S10950-021-10035-Y
antassel and ox Hubbard and Yust 2022. “Extracting high-resolution, multi-mode surface wave dispersion data from distributed acoustic sensing measurements using the multichannel analysis of surface waves. p. 0” Journal of Applied Geophysics, 205 (February): 104776. p. 2 Elsevier B.V. https://doi.org/10.1016/j.jappgeo.
Wang et al. p. 2 2025. “Enhancing subsurface seismic profiling with distributed acoustic sensing and optimization algorithms. p. 1” Journal of Rock Mechanics and Geotechnical Engineering, 17 (6): 3632–3643. p. 0 Elsevier. https://doi.org/10.1016/J.JRMGE.2024.08.
Wathelet 2005. p. 2 “Array recordings of ambient vibrations: surface-wave inversion. p. 9” Liège University (Belgium). p. 0 https://doi.org/10.1029/2008GL033256
Wathelet 20. “An improved neighborhood algorithm: Parameter conditions and dynamic scaling. p. 1” Geophysical Research Letters, 35 (9): 9301. https://doi.org/10.1029/2008GL033256
Yust et al. 202. “AS for 2-D MASW imaging: a case study on the benefits of flexible subarray processing.” Geophysical Journal International, 237 (3): 1609–1623. Oxford Academic. https://doi.org/10.1093/gji/ggae122
Yust and Menq 202. “Active-Source, Near-Surface, SurfaceWave Measurements using Distributed Acoustic Sensing (DAS), Cone Penetration Testing (CPT), and ownhole (H) Testing. p. 0” DesignSafe-CI. DesignSafe-CI. https://doi.org/10.17603/ds2-6ap5sk09
Zhang and Sanderson 2009. “JA E: Adaptive differential evolution with optional external archive. p. 2” IEEE Transactions on Evolutionary Computation, 13 (5): 945–958. p. 3 https://doi.org/10.1109/TEVC.2009.2014613
Zywicki and ix 2005. “Mitigation of Near-Field Effects for Seismic Surface Wave Velocity Estimation with ylindrical Beamformers. p. 1” Journal of Geotechnical and Geoenvironmental Engineering, 131 (8): 970–977. p. 0 American Society of Civil Engineers (ASCE). https://doi.org/10.1061/(asce)1090-0241(2005)131:8(970). p. 2
Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.
Improvements for AI systems
-
Enhanced inversion accuracy for DAS data by implementing a radial-component predominant-mode (RCPM) framework that explicitly accounts for source–receiver directivity and modal sensitivity of the Rayleigh-wave radial component. This eliminates the need for explicit modal indexing, providing a
component consistent interpretation of radial-component dispersion data.
-
Improved handling of complex stratigraphic conditions by replacing conventional multi-modal inversion with the RCPM approach, which
eliminates the need for explicit modal indexing
and avoids errors caused bysubjective analyst-driven modal interpretations.
-
More robust subsurface velocity profile estimation through a methodology that matches
measured dominant amplitude radial dispersion trends with the theoretical mode exhibiting the maximum modal amplitude,
leading tostable and reliable Vs profiles across different inversion parameterizations.
-
Mitigation of ambiguity in mode identification by using the proposed formulation to inherently identify the
mode with the highest modal participation at each frequency
rather than relying on explicit indexing, which is critical whenmodal transitions may not follow a clear sequential pattern, with energy shifting between non-adjacent modes.
-
Improved consistency between data fit and model accuracy by using an objective misfit function based on the difference between observed and calculated dispersion curves, thereby ensuring that
models that provide a good fit to the dispersion data may not correspond to physically consistent subsurface structures
is avoided.
Related papers
- Geometry-Aware Transformer for Five-Dimensional Seismic Noise Attenuation and First-Arrival Picking
- Generative deep learning improves reconstruction of global historical climate records
- Field-Deployable Hybrid Gravimetry: Projecting Absolute Accuracy Across a Remote 24km squared Survey via Daily Quantum Calibration
- Parameter-Efficient Transfer Learning for Microseismic Phase Picking Using a Neural Operator
- Scaling-law-informed neural point processes for earthquake sequence forecasting
- Supershear Rupture Indicator in Near-fault Particle Motion