A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability

arXiv:2603.02468 · cs.RO · Submitted 2026-03-02 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: We're looking at the paper: "A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability".

Dev: Here's the gist of the paper. This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability.

Rosa: The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements.

Dev: Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.9-fold increase in workspace volume.

Rosa: Hardware Design and Fabrication The soft arm fabrication process begins with 3D printing the end caps in PETG using an FDM 3D printer.

Paper summary: Rosa: So wrapping up this paper, "A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability," we see that modularity is a key feature here because it lets you scale the system by stacking identical segments to get much bigger workspaces >

Dev: Yeah, and the results show that for example, the three segment configuration achieved a planar area of one point zero seven times ten five millimeters squared and a workspace volume of one point nine two times ten seven millimeters cubed >

Taro: It’s clear that this architecture allows for significant expansion in reach when you move from a single segment to three segments, which is impressive given the comparison they made >

Rosa: And what it means for us in the real world is that if we need a robotic system that can adapt its size or reach based on the task, this modular approach gives us a scalable way to design it >

Dev: It also shows that material choice isn't just about flexibility; stiffness matters because stiffer silicone provides better load bearing capacity and geometric stability under pressure >

Taro: The authors did flag that as you stack them, the payload and self weight accumulate fast, which sets a practical limit on how many segments you can actually stack before things get too difficult to control >

Rosa: So the paper provides quantitative guidance on material selection and configuration for multi-segment soft manipulators, pointing toward careful design choices for these types of systems >

Conclusion: Rosa: So, this paper is about a new soft robotic arm that you can actually build bigger by stacking pieces on top of each other >

Dev: Yeah, they call it "A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability" and the authors are focusing on how to make these things scalable >

Rosa: It sounds like the main idea here is taking a single arm and turning it into something much more powerful by just adding more segments >

Dev: Exactly, they show that stacking those segments isn't just theoretical; it gives you a real jump in reach and volume of workspace >

Rosa: I mean, they showed that three segments achieved up to thirteen times the planar area compared to just one segment >

Dev: That’s a big number for spatial capability, but they also warned that as you stack them, the self weight and compliance really start adding up fast >

Rosa: Right, so it’s not just about making it bigger; there are real physical limits to how many segments you can practically use before things get too heavy or floppy >

Dev: And the material choice matters a lot because they found that stiffer silicone keeps the structure stable but you need way more pulling force from the tendons to move it >

Rosa: It makes you wonder what this means for building bigger, more complex soft systems that need to reach different parts of a space >

Moeen Ul Islam, Cheng Ouyang, Xinda Qi, Azlan Zahid, Xiaobo Tan, Dong Chen

Mississippi State University · Michigan State University · Texas A&M University

cs.RO

Submitted: 2026-03-02

Updated: 2026-03-04

Comments: 6 pages, 8 figures

Journal ref: 2026 IEEE/ASME International Conference on Advanced Intelligent Mechatronics (AIM), 2026

DOI: 10.1109/AIM65483.2026.11658266

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 80/100

The gist: This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability.

Key concepts

Modular Scalability
The design allows identical soft segments to be connected in series, enabling the arm's length and reach to be increased by stacking modules. This modular approach makes the robot adaptable for various structural needs by simply adding or removing segments.
Cable-Driven Actuation
The movement of each soft segment is controlled by tendons (cables) passing through a central backbone. These cables pull on the segments, which are actuated by stepper motors, allowing precise control over the arm's shape and position.
Material Stiffness Trade-off
The choice of silicone material affects performance: softer silicone offers greater bending flexibility but can sag under heavy loads. Stiffer silicone provides better structural rigidity and stability but demands much higher pulling forces from the tendons.

Terminology

Summary

This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability. p. 0

Where the paper says it

A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability Moeen Ul Islam1 , Cheng Ouyang1 , Xinda Qi2 , Azlan Zahid3 , Xiaobo Tan2 , and Dong Chen1 Abstract— This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability. The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements.

The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements. p. 0
Where the paper says it

A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability Moeen Ul Islam1 , Cheng Ouyang1 , Xinda Qi2 , Azlan Zahid3 , Xiaobo Tan2 , and Dong Chen1 Abstract— This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability. The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements.

p. 0
Where the paper says it

A Novel Modular Cable-Driven Soft Robotic Arm with Multi-Segment Reconfigurability Moeen Ul Islam1 , Cheng Ouyang1 , Xinda Qi2 , Azlan Zahid3 , Xiaobo Tan2 , and Dong Chen1 Abstract— This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability. The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements.

Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38. p. 0
Where the paper says it

The system is fabricated from soft silicone material and incorporates embedded tendon-routing channels with a protective dual-helical tendon structure. Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.

p. 0
Where the paper says it

The system is fabricated from soft silicone material and incorporates embedded tendon-routing channels with a protective dual-helical tendon structure. Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.

9-fold increase in workspace volume. p. 0
Where the paper says it

Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38. 9-fold increase in workspace volume.

p. 0
Where the paper says it

Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38. 9-fold increase in workspace volume.

Hardware Design and Fabrication

The soft arm fabrication process begins with 3D printing the end caps in PETG using an FDM 3D printer. The end caps were designed with interlocking mechanical features that embed into the silicone during curing, preventing detachment during actuation. p. 1

Where the paper says it

The soft arm fabrication process begins with 3D printing the end caps in PETG using an FDM 3D printer. The end caps were designed with interlocking mechanical features that embed into the silicone during curing, preventing detachment during actuation.

Clear McMaster-Carr Soft-Masterkleer PVC tubing with a 3 mm inner diameter and 6 mm outer diameter was used as the central backbone of the soft robot. p. 1
Where the paper says it

They were also shaped to allow modular stacking, enabling additional segments to be mounted on existing ones to extend the arm length. Clear McMaster-Carr Soft-Masterkleer PVC tubing with a 3 mm inner diameter and 6 mm outer diameter was used as the central backbone of the soft robot.

Kevlar threads were wound in a dual helical pattern around a 2 mm metal rod, which served as a mandrel during silicone casting. p. 1
Where the paper says it

The tubing runs through the center of each segment, providing a flexible yet constrained axis for tendon routing. Kevlar threads were wound in a dual helical pattern around a 2 mm metal rod, which served as a mandrel during silicone casting.

Multi-segment Configuration

The primary design objective of the proposed system is modular scalability. Each soft segment is stackable, allowing identical modules to be connected in series to extend reach. p. 1

Where the paper says it

Multi-segment Configuration The primary design objective of the proposed system is modular scalability. Each soft segment is stackable, allowing identical modules to be connected in series to extend reach.

To extend the arm, three new tendons are passed through the backbone of the existing segment. p. 1
Where the paper says it

This combination of three motors and one soft segment constitutes a single actuation level, as illustrated in Fig. To extend the arm, three new tendons are passed through the backbone of the existing segment.

The two segments are joined using three M2 screws inserted through the end-cap holes. p. 1
Where the paper says it

One end of each tendon is connected to a set of stepper motors, while the other end is routed through the tendon channels of the newly attached segment. The two segments are joined using three M2 screws inserted through the end-cap holes.

Control Electronics and Actuation

The control board consists of an ESP32 development board featuring a dual-core Tensilica Xtensa LX6 processor and multiple GPIO interfaces. Each segment is actuated by three NEMA 17 bipolar stepper motors. p. 2

Where the paper says it

(b)–(d) Progressive assembly of one-, two-, and three-segment configurations. Each segment is actuated by three NEMA 17 bipolar stepper motors.

p. 2
Where the paper says it

(b)–(d) Progressive assembly of one-, two-, and three-segment configurations. Each segment is actuated by three NEMA 17 bipolar stepper motors.

The motors are driven by TMC2209 stepper motor drivers and the ESP32 and motor drivers are mounted on a veroboard with appropriate wiring connections. p. 2
Where the paper says it

The motors are driven by TMC2209 stepper motor drivers. The ESP32 and motor drivers are mounted on a veroboard with appropriate wiring connections, together with an efficient buck converter that provides a regulated power supply to all modules.

p. 2
Where the paper says it

The motors are driven by TMC2209 stepper motor drivers. The ESP32 and motor drivers are mounted on a veroboard with appropriate wiring connections, together with an efficient buck converter that provides a regulated power supply to all modules.

Workspace Characterization

The three-dimensional workspace of the soft robotic arm was experimentally characterized by applying open-loop actuation commands. The single segment achieved a maximum radial reach of 51. p. 3

Where the paper says it

The filtered tip trajectories were used to estimate the maximum radial reach (Rmax), from which the circular planar workspace area (πR2 max) and 3D workspace volume were derived by integrating circular cross-sections along the arm’s axial direction. The single segment achieved a maximum radial reach of 51.

3 mm and a planar workspace area of approximately 8. p. 3
Where the paper says it

The single segment achieved a maximum radial reach of 51. 3 mm and a planar workspace area of approximately 8.

26×103 mm2. p. 3
Where the paper says it

3 mm and a planar workspace area of approximately 8. 26×103 mm2 .

The three-segment configuration achieved a planar area of 1. p. 0
Where the paper says it

The system is fabricated from soft silicone material and incorporates embedded tendon-routing channels with a protective dual-helical tendon structure. Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.

07×105 mm2 and a workspace volume of 1. p. 3
Where the paper says it

The three-segment configuration achieved a planar area of 1. 07×105 mm2 and a workspace volume of 1.

p. 3
Where the paper says it

The three-segment configuration achieved a planar area of 1. 07×105 mm2 and a workspace volume of 1.

92×107 mm3. p. 3
Where the paper says it

07×105 mm2 and a workspace volume of 1. 92×107 mm3 , indicating that workspace scalability arises primarily from enhanced spatial flexibility rather than simple radial extension.

p. 3
Where the paper says it

07×105 mm2 and a workspace volume of 1. 92×107 mm3 , indicating that workspace scalability arises primarily from enhanced spatial flexibility rather than simple radial extension.

Effect of Material Stiffness

The results revealed a clear trade-off between compliance and stiffness: softer silicone improved bending flexibility, while stiffer silicone improved structural rigidity and load-bearing stability. The stiffer Ecoflex 00-50 maintained a much higher structural stiffness, requiring substantially larger tendon forces (15–20 N) but preserving greater geometric stability under load. p. 4

Where the paper says it

For example, the Ecoflex 00-10 actuator showed a drop in bending angle from approximately 162° to 91° and a decrease in vertical displacement from about 110 mm to 57 mm, while the required tendon tension increased from about 7. In contrast, the stiffer Ecoflex 00- 50 maintained a much higher structural stiffness, requiring substantially larger tendon forces (15–20 N) but preserving greater geometric stability under load.

Payload and Structural Loading Limits

As identical segments were stacked from one to two and then three, the effective self-weight and compliance of the system increased, resulting in reduced bending, higher tendon tension, and decreased vertical displacement at the base segment. This demonstrates that payload and self-weight accumulate rapidly in modular configurations, imposing a practical limit on scalable segment stacking. p. 4

Where the paper says it

In contrast, tendon tension follows a different and more nonlinear growth pattern, suggesting that actuation effort scales more aggressively than kinematic loss as structural load accumulates. This demonstrates that payload and self-weight accumulate rapidly in modular configurations, imposing a practical limit on scalable segment stacking.

Conclusion

These observations provided quantitative guidance for material selection and modular configuration in multi-segment soft manipulators. The paper highlights key considerations for the design of modular, cabledriven soft manipulators. p. 4

Where the paper says it

These observations provided quantitative guidance for material selection and modular configuration in multi-segment soft manipulators. These results highlight key considerations for the design of modular, cabledriven soft manipulators, and together provide quantitative guidance for material selection and modular configuration in multi-segment systems.

Future work will incorporate the theoretical kinematics of tendon-driven continuum manipulators using the constant-curvature assumption to enable more precise control and trajectory planning. p. 4
Where the paper says it

These results highlight key considerations for the design of modular, cabledriven soft manipulators, and together provide quantitative guidance for material selection and modular configuration in multi-segment systems. In future work, the theoretical kinematics of tendon-driven continuum manipulators will be incorporated using the constant-curvature assumption [23], [24] to enable more precise control and trajectory planning based on the experimentally characterized material and geometric properties of the proposed modular platform.

Pruning redundant reasoning tokens

The paper presents a novel, modular, cable-driven soft robotic arm with multi-segment reconfigurability. The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements. Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.9-fold increase in workspace volume.

How the training signal is built

The control board consists of an ESP32 development board featuring a dual-core Tensilica Xtensa LX6 processor and multiple GPIO interfaces. Each segment is actuated by three NEMA 17 bipolar stepper motors. The motors are driven by TMC2209 stepper motor drivers and the ESP32 and motor drivers are mounted on a veroboard with appropriate wiring connections.

Where the gains come from

The three-segment configuration achieved a planar area of 1.07×105 mm2 and a workspace volume of 1.92×107 mm3. The results revealed that softer Ecoflex 00-10 and 00-30 achieved larger bending but exhibited backbone sagging and kinematic degradation under heavier load. p. 4

Where the paper says it

CONCLUSIONS This work presented a modular, cable-driven soft robotic arm with a reconfigurable multi-segment architecture that enabled scalable extension without disassembly. Experimental results showed that softer Ecoflex 00-10 and 00-30 achieved larger bending but exhibited backbone sagging and kinematic degradation under heavier load, whereas stiffer Ecoflex 00- 50 improved load-bearing capacity and geometric stability at the expense of bending range and higher pulling force requirement.

The stiffer Ecoflex 00-50 improved load-bearing capacity and geometric stability at the expense of bending range and higher pulling force requirement. p. 4
Where the paper says it

CONCLUSIONS This work presented a modular, cable-driven soft robotic arm with a reconfigurable multi-segment architecture that enabled scalable extension without disassembly. Experimental results showed that softer Ecoflex 00-10 and 00-30 achieved larger bending but exhibited backbone sagging and kinematic degradation under heavier load, whereas stiffer Ecoflex 00- 50 improved load-bearing capacity and geometric stability at the expense of bending range and higher pulling force requirement.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Modular Reconfiguration for Diverse Tasks: The system can be scaled to adapt to diverse structural and application requirements by using independent segment control, allowing for scalable adaptation based on task-specific needs.

  2. Enhanced Workspace Exploration: The arm can achieve a 38.9-fold increase in workspace volume compared to a single segment, enabling the robot to cover significantly larger operational areas than monolithic systems.

  3. Stiffness Tuning for Performance Optimization: The AI system can dynamically tune material stiffness based on the required operation, leveraging the finding that softer silicone improved bending flexibility or stiffer silicone improved structural rigidity and load-bearing stability.

  4. Payload-Aware Actuation Control: The control system can manage actuation effort based on external forces, as demonstrated by how tendon tension increased under increasing payloads, allowing for predictive load management.

  5. Self-Weight Compensation Modeling: The system can incorporate models accounting for accumulated self-weight and compliance, which will allow the AI to predict the resulting reduced bending and required tendon tension when stacking more segments.

Abstract

This paper presents a novel, modular, cable-driven soft robotic arm featuring multi-segment reconfigurability. The proposed architecture enables a stackable system with independent segment control, allowing scalable adaptation to diverse structural and application requirements. The system is fabricated from soft silicone material and incorporates embedded tendon-routing channels with a protective dual-helical tendon structure. Experimental results showed that modular stacking substantially expanded the reachable workspace: relative to the single-segment arm, the three-segment configuration achieved up to a 13-fold increase in planar workspace area and a 38.9-fold increase in workspace volume. Furthermore, this study investigated the effect of silicone stiffness on actuator performance. The results revealed a clear trade-off between compliance and stiffness: softer silicone improved bending flexibility, while stiffer silicone improved structural rigidity and load-bearing stability. These results highlight the potential of stiffness tuning to balance compliance and strength for configuring scalable, reconfigurable soft robotic arms.

Sources

Related papers