Challenges in the Proper Metrological Verification of Smart Energy Meters

arXiv:2601.16612 · eess.SY, cs.SY · Submitted 2026-01-23 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: I'm Rosa.

Dev: And I'm Dev, here with Taro.

Rosa: We're looking at the paper: "Challenges in the Proper Metrological Verification of Smart Energy Meters".

Dev: Here's the gist of the paper. The most common instruments currently used to measure active/reactive energy and power quality indicators are smart energy meters (EM).

Rosa: Problem Statement The verification of such meters is currently performed under ideal conditions or with simple signal models, which do not recreate actual states occurring in the power grid and do not ensure the verification of the properties of their signal chains.

Dev: The widespread use of such meters and competition among manufacturers forces the drive for low prices.

Rosa: The complexity of smart EM (software and hardware) and the drive for low prices are somewhat contradictory.

Title and authors: Rosa: We’ve just talked about how we need better verification methods for smart energy meters, focusing on finding a minimal set of test signals that work in real-world scenarios. Now we look at the specific details of this paper, "Challenges in the Proper Metrological Verification of Smart Energy Meters."

Dev: This paper sets out the problem clearly: current testing is too idealized and doesn't account for actual grid states, which leads to imperfections in the signal chains of these meters as they try to keep costs low.

Taro: It’s like they’re saying we need to test a car on a perfectly flat track instead of letting it drive on bumpy roads, because if you only test on flat ground, you miss all the real problems.

Rosa: Exactly. The paper summarizes that they are presenting challenges in verifying these meters because the existing methods don't replicate actual grid states and fail to ensure the properties of those measurement chains one <ref:2601.16612#pg1>.

Dev: They point out that this is happening because there’s a lot of oversimplification in the measurement signal chains just to keep the price down compared to dedicated, specialized measuring instruments.

Taro: So if we look at what they propose, they are suggesting a new verification procedure that uses these minimal reference test signals to increase the reliability of what these meters actually measure.

Rosa: The proposed improvement is this metrologically oriented approach, where a simple analytical test signal can still reveal significant imperfections in the measurement and signal processing chains under conditions representative of modern grids.

Dev: They are aiming to identify a practical route toward defining that minimal set of reference test signals—one that is suitable for rigorous metrological assessment but also effective at detecting reliability issues when things are actually happening on the grid.

Taro: The implication for us is that we need to move beyond simple, idealized tests and start designing verification procedures based on more realistic operating conditions.

Rosa: So, the paper’s focus is clearly shifting from just checking compliance to ensuring actual performance reliability under realistic operating conditions.

The paper's summary: Dev: Building on what we said, let’s look at what specific improvements the authors suggest in this paper about verifying smart energy meters. They aren't just pointing out problems; they are proposing a path forward.

Rosa: Their main improvement is defining a new verification procedure that uses a minimal set of test signals. This set needs to be both suitable for rigorous metrological assessment and effective at spotting reliability issues when the meters are actually operating in real conditions one <ref:2601.16612#pg1>.

Taro: That sounds like they are trying to solve the problem of dispersion by creating a standard, reliable way to check these meters that works regardless of which manufacturer you buy.

Dev: They also propose improving diagnostic capabilities by moving beyond standard tests to include conditions that occur in real power grids, like voltage distortion and voltage fluctuations. This is meant to catch malfunctions that are currently hard to find because all the meters are scattered around.

Rosa: By testing against signals that recreate these complex, real-world grid states instead of relying only on idealized two-component signals, they aim for a verification method that works across multiple measurement signal chains under realistic operating conditions.

Taro: So if we’re designing future tests, the idea is to move away from simple inputs and toward testing against more complex disturbances that mimic actual grid behavior.

Dev: And the analysis of their test signal construction shows they can analytically calculate uncertainty budgets and determine how much error you should expect based on things like the frequency of an additional component in that test signal.

Rosa: They found that analyzing sample results for things like peak power, total harmonic distortion, and fundamental component value as a function of the test signal's frequency allows them to identify irregularities in the meter operation.

Taro: The analysis shows that discrepancies are largest when testing at frequencies up to one hundred hertz across all those measured parameters <ref:2601.16612#pg1>. That gives us a concrete range for where we need to focus our attention.

The paper's improvements: Rosa: So, wrapping things up, the paper concludes by summarizing the necessity and the challenges involved in finding that smallest possible number of test signals needed for accurate metrological verification of smart energy meters one <ref:2601.16612#pg1,metrological verification of smart energy meters>.

Dev: They reiterate that these discrepancies they found across different manufacturers and equipment incompatibility are not specific to a single faulty meter but happen across multiple smart energy meters from different companies.

Taro: It really hammers home the point that we need more robust verification methods because the current tests are too limited for real-world deployment scenarios.

Rosa: The paper presents this simple test signal as a tool for metrological verification, and the test results clearly show significant discrepancies in smart energy meter readings and incompatibility with specialized equipment one <ref:2601.16612#pg1>.

Dev: Ultimately, their research demonstrates that we need to figure out how to find the smallest possible number of test signals that will enable accurate metrological verification of these meters and increase the reliability of their measurement results in real-world conditions.

Taro: To add one last thing, it points out that they are currently testing smart energy meters under ideal conditions or with simple test signals, which doesn't help in effectively identifying imperfections in their measurement and signal chains.

Rosa: It’s a call for a better approach to verification that addresses the reality of how these meters operate on the power grid today.

Dev: That’s our take on this paper, "Challenges in the Proper Metrological Verification of Smart Energy Meters." We're going to keep an eye on these kinds of studies as we look at how we can make sure our energy measurements are trustworthy.

Conclusion: Rosa: So we’ve been looking at how hard it is to actually verify smart energy meters in real life, and this paper, "Challenges in the Proper Metrological Verification of Smart Energy Meters," shows why current testing methods fall short when you're trying to catch real-world problems.

Dev: It boils down to this: the existing tests are too simple, they don't replicate what actually happens on a modern power grid, and that leads to measurement errors in the signal chains of these meters because manufacturers are pushing for lower prices.

Taro: It’s like they’re trying to test a car on a perfectly flat track instead of letting it drive on bumpy roads, and they miss all the real problems that happen when you hit something unexpected.

Rosa: Exactly. The authors propose this new verification procedure where they use a minimal set of test signals that are rigorous enough for metrology but also effective at spotting reliability issues under realistic operating conditions.

Dev: They’re aiming to move beyond ideal testing by incorporating conditions like "clipped sine" voltage distortion and actual voltage fluctuations, which helps find those malfunctions that get missed when meters are just scattered around.

Taro: That means they want a verification method that works across multiple measurement signal chains under those complex, real-world grid states instead of relying on one simple two-component input.

Rosa: The paper shows that even with a simple, analytically defined test signal like the one they proposed, you can still find significant imperfections in how the meter measures things.

Dev: They found that using this signal allows for analytical calculation and determining an uncertainty budget, and they noted that the largest discrepancies across all measured parameters are when the additional component in that test signal is up to one hundred hertz.

Taro: So it’s not just about finding a single broken meter; it’s about seeing how different meters from different companies behave differently under the same realistic stress.

Rosa: That's what they emphasize—the discrepancies aren't specific to one bad device but happen across multiple smart energy meters in the field.

Dev: So, the conclusion is that finding that smallest possible number of test signals is really necessary if we want accurate metrological verification and increased reliability for these meters in the real world.

Taro: It also highlights how current testing methods fail because they don't recreate those actual states occurring on a modern power grid or allow us to effectively identify imperfections in the measurement chains.

Rosa: So, this paper is really pointing toward the need for better, more realistic testing standards to ensure these meters are reliable when people are actually using them.

Dev: It sets up a challenge for us engineers and researchers: how do we design these verification procedures that scale across different hardware while still being rigorous?

Taro: We need to figure out how to test under real-world stress without needing a massive amount of specialized equipment for every single check.

Rosa: That’s the challenge. So, that wraps up our look at "Challenges in the Proper Metrological Verification of Smart Energy Meters." Next time we'll be talking about how we can use AI to build those better, more realistic test scenarios.

Antonio Bracale, Jakub Janowicz, Piotr Kuwałek, Grzegorz Wiczy łnski

University of Naples Parthenope · Institute of Electrical Engineering and Electronics and University of Technology Poznan

eess.SY, cs.SY

Submitted: 2026-01-23

Updated: 2026-11-07

Comments: 5 pages, 5 figures, submitted to IEEE conferences: 2026 22nd International Conference on Harmonics & Quality of Power (ICHQP)

Journal ref: A. Bracale, J. Janowicz, P. Kuwałek and G. Wiczyński, "Challenges in the Proper Metrological Verification of Smart Energy Meters," 2026 22nd ICHQP, Dresden, Germany, 2026

DOI: 10.1109/ICHQP67927.2026.11756316

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 77/100

The gist: The most common instruments currently used to measure active/reactive energy and power quality indicators are smart energy meters (EM).

Key concepts

Smart Energy Meters (EM)
These are modern meters that measure active/reactive energy and power quality indicators. They are complex systems involving both hardware and software, making their verification difficult due to widespread use and low-cost manufacturing pressures.
Metrological Verification
This is the process of rigorously testing a meter's accuracy against known standards. The paper argues that current verification methods fail because they don't simulate real grid conditions, leading to unreliable measurements in practice.
Test Signal Construction
The authors developed a specific, simple mathematical signal (u(t) = √2Uc cos (2πfct) + u∗i cos (2πfit)) designed to be easy to analyze but representative of real grid states. This signal is used to probe the meter's internal measurement and processing chains.
Discrepancies Across Manufacturers
Tests using the simple signal showed significant differences in results between smart EMs from various manufacturers, even when compared against advanced equipment. These variations point to inconsistencies in how different meters implement algorithms like THD determination.

Terminology

Summary

The most common instruments currently used to measure active/reactive energy and power quality indicators are smart energy meters (EM). p. 0

Where the paper says it

kuwalek@put. pl Abstract—The most common instruments currently used to measure active/reactive energy and power quality indicators are smart energy meters (EM).

Problem Statement

The verification of such meters is currently performed under ideal conditions or with simple signal models, which do not recreate actual states occurring in the power grid and do not ensure the verification of the properties of their signal chains. The widespread use of such meters and competition among manufacturers forces the drive for low prices. p. 0

Where the paper says it

For the purpose of Open Access, the author has applied a CC BY public copyright licence to any Author Accepted Manuscript (AAM) version arising from this submission. The widespread use of such meters and competition among manufacturers forces the drive for low prices.

The complexity of smart EM (software and hardware) and the drive for low prices are somewhat contradictory. p. 0
Where the paper says it

The widespread use of such meters and competition among manufacturers forces the drive for low prices. The complexity of smart EM (software and hardware) and the drive for low prices are somewhat contradictory.

Due to the dispersion of meters, detecting malfunctions is difficult. p. 0
Where the paper says it

It is especially important to remember that any performance imperfections in smart EM can occur in a very large number of cases. Due to the dispersion of meters, detecting malfunctions is difficult.

Proposed Verification Approach

The paper proposes a metrologically-oriented verification perspective for smart EM. The contribution lies in showing that a simple and analytically defined test signal can still reveal significant imperfections in the measurement and signalprocessing chains of commercially available meters under conditions representative of modern grids. p. 0

Where the paper says it

Contribution Unlike previous studies that mainly report meter behavior for specific loads or isolated power-quality phenomena, this paper proposes a metrologically-oriented verification perspective for smart EM. Its contribution lies in showing that a simple and analytically defined test signal can still reveal significant imperfections in the measurement and signalprocessing chains of commercially available meters under conditions representative of modern grids.

The paper proposes to identify a practical route toward defining a minimal set of reference test signals that can be both suitable for rigorous metrological assessment and effective in detecting reliability issues under realistic operating conditions. p. 0
Where the paper says it

Its contribution lies in showing that a simple and analytically defined test signal can still reveal significant imperfections in the measurement and signalprocessing chains of commercially available meters under conditions representative of modern grids. Therefore, the paper does not provide additional experimental evidence of meter inaccuracies, but proposes to identify a practical route toward defining a minimal set of reference test signals that can be both suitable for rigorous metrological assessment and effective in detecting reliability issues under realistic operating conditions.

Test Signal Construction

The paper presents an example signal that has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid. The test signal can be expressed as follows: u(t) = √2Uc cos (2πfct) + u∗i cos (2πfit) (1). p. 1

Where the paper says it

This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid. The test signal can be expressed as follows: u(t) = √ 2Uc cos (2πfct) + u ∗ i cos (2πfit) (1) where Uc is the rms value of the fundamental component at the fundamental frequency fc, and u ∗ i is the relative value of the component at the frequency fi (subharmonic/interharmonic/harmonic component).

Experimental Findings and Discrepancies

Tests were conducted using this signal on smart EM from three different manufacturers. Significant discrepancies can be observed between the measurement results of the advanced measurement infrastructure, such as the class A PQA, and the results obtained for individual smart EM. p. 2

Where the paper says it

3 presents the characteristics of the minimum and maximum Pst values determined by individual smart EM (EM1/EM2/EM3) and by the PQA as a function of the frequency fi of the additional component of the test signal. On the obtained results, significant discrepancies can be observed between the measurement results of the advanced measurement infrastructure, such as the class A PQA, and the results obtained for individual smart EM.

These discrepancies are probably related to different implementations of the THD determination algorithm on smart EM processors [3], [4], and the applied fundamental component estimation method. p. 3
Where the paper says it

It is worth noting that the results obtained by the class A PQA are consistent with those obtained by analytical calculations [3], [4]. These discrepancies are probably related to different implementations of the THD determination algorithm on smart EM processors [3], [4], and the applied fundamental component estimation method, where the results may be influenced by the properties of the filter or frequency analysis algorithm used.

Conclusion

The presented research results demonstrate the necessity and challenges in finding the smallest possible number of test signals that will enable accurate metrological verification of smart EM and thus increase the reliability of these meters’ measurement results in real-world conditions. p. 4

Where the paper says it

These discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers. The presented research results demonstrate the necessity and challenges in finding the smallest possible number of test signals that will enable accurate metrological verification of smart EM and thus increase the reliability of these meters’ measurement results in real-world conditions.

The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

p. 4
Where the paper says it

Due to its simple functional description, the selected test signal can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

These discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers. p. 4
Where the paper says it

The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. These discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers.

The presented research results demonstrate the necessity and challenges in finding the smallest possible number of test signals that will enable accurate metrological verification of smart EM and thus increase the reliability of these meters’ measurement results in real-world conditions. The paper presents a simple test signal that can be used for metrological verification of the measurement results. p. 1
Where the paper says it

SELECTED RESEARCH RESULTS AND DISCUSSION Section II indicates that smart EM testing should be performed using signals that recreate real states (including harmonics, “clipped sine” distortions and voltage fluctuations), or using signals that are as simple as possible, enabling metrological assessment (thanks to the simple and explicit form of the equation describing the test signal) and enabling verification of the largest possible number of measurement signal chains. This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid.

p. 1
Where the paper says it

SELECTED RESEARCH RESULTS AND DISCUSSION Section II indicates that smart EM testing should be performed using signals that recreate real states (including harmonics, “clipped sine” distortions and voltage fluctuations), or using signals that are as simple as possible, enabling metrological assessment (thanks to the simple and explicit form of the equation describing the test signal) and enabling verification of the largest possible number of measurement signal chains. This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid.

p. 1
Where the paper says it

SELECTED RESEARCH RESULTS AND DISCUSSION Section II indicates that smart EM testing should be performed using signals that recreate real states (including harmonics, “clipped sine” distortions and voltage fluctuations), or using signals that are as simple as possible, enabling metrological assessment (thanks to the simple and explicit form of the equation describing the test signal) and enabling verification of the largest possible number of measurement signal chains. This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid.

p. 1
Where the paper says it

SELECTED RESEARCH RESULTS AND DISCUSSION Section II indicates that smart EM testing should be performed using signals that recreate real states (including harmonics, “clipped sine” distortions and voltage fluctuations), or using signals that are as simple as possible, enabling metrological assessment (thanks to the simple and explicit form of the equation describing the test signal) and enabling verification of the largest possible number of measurement signal chains. This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid.

p. 1
Where the paper says it

SELECTED RESEARCH RESULTS AND DISCUSSION Section II indicates that smart EM testing should be performed using signals that recreate real states (including harmonics, “clipped sine” distortions and voltage fluctuations), or using signals that are as simple as possible, enabling metrological assessment (thanks to the simple and explicit form of the equation describing the test signal) and enabling verification of the largest possible number of measurement signal chains. This section presents selected results for an example signal that, on the one hand, has a simple functional description, which facilitates metrological evaluation and, on the other hand, allows for the properties of the evaluation of the measurement chain in relation to potential conditions that can occur in a real power grid.

The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. The paper presents a simple test signal that can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. The paper presents a simple test signal that can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

References

The paper references various standards and research papers to support its technical claims. The paper also cites specific literature regarding meter behavior and power quality phenomena. p. 0

Where the paper says it

Taking all of the above into account, it is necessary to develop a test procedure for smart EM to verify energy measurement errors and indicators that determine the quality of power using smart EM, considering conditions that occur in real power networks. Contribution Unlike previous studies that mainly report meter behavior for specific loads or isolated power-quality phenomena, this paper proposes a metrologically-oriented verification perspective for smart EM.

For instance, it cites studies on distortion in clipped sinewaves [19] and voltage fluctuations [20]. p. 1
Where the paper says it

In reality, voltage and current signals contain a set of harmonics that define the quasi-steady state shape. Furthermore, it is worth noting that many disturbances in PQ occur simultaneously in modern power grids, such as “clipped sine” voltage distortion [19] as a result of the input stages of switchedmode power supplies, and voltage fluctuations [20] resulting from sudden load changes in the power network.

Specific standards like IEC 61000-4-30 [15] are mentioned for power quality measurement methods. p. 4
Where the paper says it

[13] Standard CENELEC - EN 50470-1:2006 Electricity metering equipment (a. ) Part 1: General requirements, tests and test conditions - Metering equipment (class indexes A, B and C) [14] Standard CENELEC - EN 50470-3:2022 Electricity metering equipment - Part 3: Particular requirements - Static meters for AC active energy (class indexes A, B and C) [15] Standard IEC 61000-4-30:2025 EMC - Part 4-30: Testing and measurement techniques - Power quality measurement methods [16] Standard IEC 61000-4-7:2002+AMD1:2008 CSV EMC - Part 4-7: Testing and measurement techniques - General guide on harmonics and interharmonics measurements and instrumentation, for power supply systems and equipment connected thereto [17] Standard IEC 61000-4-15:2010 RLV EMC - Part 4-15: Testing and measurement techniques - Flickermeter - Functional and design specifications.

The test signal for the selected fi ranges did not cause the analyzed PQ disturbances (voltage fluctuations, voltage distortion, frequency fluctuations). p. 4
Where the paper says it

If the confidence intervals for the unknown measured quantities overlap, it can be assumed that the readings of the tested smart EM are correct. The results presented show that in practice there are discrepancies in the readings that significantly exceed the permissible limit values of selected parameters in the power network, whereas the analyzed test signal for the selected fi ranges did not cause the analyzed PQ disturbances (voltage fluctuations, voltage distortion, frequency fluctuations).

The discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers. p. 4
Where the paper says it

The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. These discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers.

The paper points out that currently available smart EM are tested under ideal conditions or with simple test signals, which do not recreate the actual states occurring in modern power grids or allow for the effective identification of imperfections in their measurement and signal chains. p. 4
Where the paper says it

As a result, smart EM can exhibit significant imperfections in their measurement and signal chains. The paper points out that currently available smart EM are tested under ideal conditions or with simple test signals, which do not recreate the actual states occurring in modern power grids or allow for the effective identification of imperfections in their measurement and signal chains.

The results demonstrate the necessity and challenges in finding the smallest possible number of test signals that will enable accurate metrological verification of smart EM and thus increase the reliability of these meters’ measurement results in real-world conditions. p. 4
Where the paper says it

These discrepancies and variations are not specific to a single faulty smart EM from a single manufacturer but occur across multiple smart EM from different manufacturers. The presented research results demonstrate the necessity and challenges in finding the smallest possible number of test signals that will enable accurate metrological verification of smart EM and thus increase the reliability of these meters’ measurement results in real-world conditions.

The paper presents a simple test signal that can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used. The paper presents a simple test signal that can be used for metrological verification of the measurement results. The test results show significant discrepancies in smart EM readings and incompatibility with the current specialized equipment used.

Table Summary

Table I summarizes the maximum values of ∆AI and R in the individual fi ranges for Pst, THD [%], and fc. Analyzing sample results for Pst, THD, and fc as a function of the frequency fi of the additional component of the test signal, it can be seen that using a simple test signal allows for the identification of a number of irregularities in the operation of the tested smart EM. p. 3

Where the paper says it

40 [700;800) 0. 30 Analyzing sample results for Pst, THD, and fc as a function of the frequency fi of the additional component of the test signal, it can be seen that using a simple test signal allows for the identification of a number of irregularities in the operation of the tested smart EM.

This analysis confirms that simple signals enable analytical calculation and uncertainty budget determination. p. 3
Where the paper says it

30 Analyzing sample results for Pst, THD, and fc as a function of the frequency fi of the additional component of the test signal, it can be seen that using a simple test signal allows for the identification of a number of irregularities in the operation of the tested smart EM. On the one hand, a simple test signal allows for the analytical calculation of reference indicators, and based on the known properties of the source used, it is possible to determine the uncertainty budget of the set

The results show that discrepancies are largest for fi up to 100 Hz across all measured parameters. p. 4
Where the paper says it

If the confidence intervals for the unknown measured quantities overlap, it can be assumed that the readings of the tested smart EM are correct. The results presented show that in practice there are discrepancies in the readings that significantly exceed the permissible limit values of selected parameters in the power network, whereas the analyzed test signal for the selected fi ranges did not cause the analyzed PQ disturbances (voltage fluctuations, voltage distortion, frequency fluctuations).

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Develop a new verification procedure for smart EM whose implementation will increase the reliability of measurements performed by such meters. This procedure should utilize a minimal set of test signals that can be both suitable for rigorous metrological assessment and effective in detecting reliability issues under realistic operating conditions.

  2. Improve the diagnostic capabilities of smart EM by moving beyond standard tests to incorporate conditions occurring in real power grids, such as clipped sine voltage distortion and voltage fluctuations. This will help detect malfunctions that are difficult to find due to the dispersion of meters.

  3. Enhance the ability of smart EM to handle simultaneous disturbances in power quality (PQ) by testing against signals that recreate these complex, real-world grid states rather than relying on idealized two-component signals. This allows for verification across multiple measurement signal chains under realistic operating conditions.

Abstract

The most common instruments currently used to measure active/reactive energy and power quality indicators are smart energy meters (EM). Unfortunately, the verification of such meters is currently performed under ideal conditions or with simple signal models, which do not recreate actual states occurring in the power grid and do not ensure the verification of the properties of their signal chains. This paper presents challenges in proper metrological verification of smart EM. It presents existing legal and normative requirements and scientific research directions regarding these meters. Although the meters tested comply with the normative and legal requirements, the results reveal numerous imperfections in the signal and measurement chains for the selected test signal. Based on the results of the research results, further directions have been determined in the field of smart EM.

Related papers