Hybrid non-degenerate parametric amplifier for a microwave cavity mode and an NV ensemble

arXiv:2601.03407 · quant-ph · Submitted 2026-01-06 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Quantum Radio. Generated commentary on the latest quantum physics and condensed matter papers.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Hybrid non-degenerate parametric amplifier for a microwave cavity mode and an NV ensemble".

Paper summary: Kai: So we just covered how they set up the hybrid non-degenerate parametric amplifier, focusing on what they claim is possible with this combination of a microwave mode and an NV ensemble. The thesis is that you can use these two components to amplify signals in both parts at room temperature and also at cryogenic temperatures >

Mira: They show that this setup allows for generating both two-mode squeezing, which means entanglement between the cavity and the spins, and single-mode squeezing for either system >

Lev: They are operating under the assumption that both the cavity mode and the spin ensemble stay in their linear regime when they do this amplification stuff >

Kai: The physical system itself is a single microwave resonator interacting with an ensemble of nitrogen-vacancy centers in diamond, which they treat as two level systems >

Mira: They start by writing down the rate Hamiltonian for this coupled cavity/NV system under standard cavity QED approximations, which includes terms like the cavity frequency, the spin frequency modulated by a microwave tone, and the coupling strength between them >

Lev: They simplify this because they note that because of how symmetric the interaction is with respect to all those spins, it only populates completely symmetric superposition states of the spins known as Dicke states >

Kai: This leads them to rewrite their rate Hamiltonian in a more manageable form where they treat the spins almost like another harmonic oscillator with its own frequency and damping rate >

Mira: They then define the single mode and two mode covariance matrices for both oscillators, which is how they track all the noise and squeezing information for each part of the system >

Lev: The equation they use to evolve this two mode covariance matrix includes terms that describe amplification, damping from the cavity loss, and damping from the spin linewidth at nonzero temperatures >

Kai: They quantify amplification using a logarithmic scale called S of V, which is defined as ten log ten p V over V zero >

Mira: When they analyzed the driving conditions, they found specific resonance conditions where the drive frequency has to be an integer divisor of either the sum or difference of those two frequencies >

Lev: And when you maximize that amplification and squeezing rate, it happens at a very specific condition where the drive frequency is equal to omega c plus omega s when you are pushing that drive amplitude as high as possible >

Kai: This resonance occurs in the dispersive regime where the difference between those two frequencies is much larger than their coupling strength >

Mira: So, what this means for us is that they've found a way to achieve amplification and squeezing across both systems using this hybrid parametric amplifier architecture >

Conclusion: Kai: To wrap up on the paper "Hybrid non-degenerate parametric amplifier for a microwave cavity mode and an NV ensemble," the main points are about what this hybrid device can do. It shows you can amplify and squeeze both the microwave cavity mode and the NV spin ensemble >

Mira: And they prove that with time dependent control over how far apart those two systems are tuned, you can take their initial two-mode squeezing, which is entanglement between them, and transform it into individual squeezing for either one of the oscillators >

Lev: So what this implies for building something real is that this isn't just a theoretical exercise; they show a method to adjust the squeezing so that you get the best possible two-mode squeezing available >

Kai: It opens up possibilities for using this to squeeze the collective state of an NV ensemble, which is useful for manipulating those spins in some way >

Mira: And it provides a means to generate entanglement between an ensemble of these spins and a microwave field, which could be a pathway toward practical quantum applications >

Lev: The limitation they mention is that implementing this hybrid amplifier requires you to have either two resonant modes in the cavity or two interlocking cavities, which is the physical hurdle you have to overcome >

Kai: So, for those who want to hear about this paper, it's about combining microwave fields and solid-state spins into a working parametric amplifier architecture >

Roman Ovsiannikov, Kurt Jacobs, Andrii G. Sotnikov, Matthew E. Trusheim, Denys I. Bondar

Akhiezer Institute for Theoretical Physics at NSC KIPT, Ukraine · Advanced Photonics and Electronics Division of the U.S. Army DEVCOM Army Research Laboratory, USA · Department of Physics at the University of Massachusetts at Boston, USA · Education and Research Institute School of Physics and Technology at Karazin Kharkiv National University, Ukraine · Department of Electrical Engineering and Computer Science at Massachusetts Institute of Technology, USA · Department of Physics and Engineering Physics at Tulane University, USA

quant-ph

Submitted: 2026-01-06

Updated: 2026-11-18

Comments: 14 pages, 6 figures

License: http://creativecommons.org/licenses/by/4.0/

Importance score: 86/100

The gist: Hybrid non-degenerate parametric amplifier for a microwave cavity mode and an NV ensemble introduces an implementation of a non-degenerate parametric amplifier in which the signal and idler modes…

Key concepts

Non-degenerate Parametric Amplifier
This device amplifies signals by using a parametric drive that couples a microwave cavity mode to an ensemble of spins. It works by creating correlated excitations between the cavity and the spins, leading to signal amplification and the generation of quantum states like squeezing.
Nitrogen-Vacancy (NV) Ensemble
This refers to a collection of NV centers in diamond, which are treated as two-level quantum systems. These spins interact with the microwave cavity mode, allowing for complex quantum operations and entanglement between the light field and the spin system.
Two-mode Squeezing
Squeezing is a quantum phenomenon where the noise (uncertainty) in one property of a system is reduced below its standard limit. Two-mode squeezing specifically refers to reducing noise correlations between two different systems, such as the cavity and the NV ensemble.
Dicke States
These are specific, highly symmetric superposition states that arise when multiple two-level systems (like the NVs) interact symmetrically with a field. The dynamics of the coupled system are restricted to populating these Dicke states, simplifying the theoretical description.

Terminology

Summary

Hybrid non-degenerate parametric amplifier for a microwave cavity mode and an NV ensemble introduces an implementation of a non-degenerate parametric amplifier in which the signal and idler modes, respectively, a microwave mode and an ensemble of spins (e. p. 0

Where the paper says it

Bondar 6, ¶ 1Akhiezer Institute for Theoretical Physics, NSC KIPT, Akademichna 1, 61108 Kharkiv, Ukraine 2Advanced Photonics and Electronics Division, U. Army DEVCOM Army Research Laboratory, Adelphi, Maryland 20783, USA 3Department of Physics, University of Massachusetts at Boston, Boston, Massachusetts 02125, USA 4Education and Research Institute “School of Physics and Technology”, Karazin Kharkiv National University, Svobody Square 4, 61022 Kharkiv, Ukraine 5Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, Massachusetts 02139, USA 6Department of Physics and Engineering Physics, Tulane University, New Orleans, Louisiana 70118, USA (Dated: January 8, 2026) We introduce an implementation of a non-degenerate parametric amplifier in which the signal and idler modes, respectively, a microwave mode and an ensemble of spins (e.

g., nitrogen-vacancy centers in diamond), are operated in their linear regime This paramp, which amplifies signals in both parts at room and cryogenic temperatures, can be used to generate both the two-mode and single-mode squeezing of either system

System Description

The physical system considered is a single mode of a microwave resonator interacting with an ensemble of N nitrogen-vacancy centers, which are treated as two-level systems The rate Hamiltonian for the coupled cavity/NV system is expressed under the usual cavity-QED approximations as H˜ = ωca†a + [ωs + Λ sin(ωt)]S z2 + g(a + a†)(S − + S† −) The size of the Hilbert space of the coupled system grows exponentially with the number of NVs, which is referred to as spins Fortunately, since the interaction between the cavity and the spins is completely symmetric in the spins, dynamics can only populate completely symmetric superposition states of the spins (the Dicke states) The rate Hamiltonian becomes H˜ = ωca†a + [ωs + Λ sin(ωt)]Jz + g(a + a†)(J− + J+), where J+ = J†− With the spins remaining in their linear regime, we can write the rate Hamiltonian as H˜HP = ωca†a + [ωs + Λ sin(ωt)]b†b + g(a + a†)(b + b†)

Theoretical Framework

The theoretical description involves defining single-mode and two-mode covariance matrices for the quadratures of each oscillator, as well as a four×4 covariance matrix for all four quadratures The X and Y quadrature operators are defined as Xa = (a + a†)/2, Xb = (b + b†)/2, Ya = (a − a†)/(2i), and Yb = (b − b†)/(2i) The covariance matrix for the full two-mode system is given by C = ⟨vvT⟩ − ⟨v⟩⟨vT⟩ The equation of motion for the two-mode covariance matrix is dCdt=A(t)C + CAT(t) + G The logarithmic scale is used to quantify amplification and squeezing, where the amount of squeezing (amplification) for that quadrature is defined to be S(V) = 10 log10 p V/V0 = 10 log10 2√V

Analysis of Driving Conditions

A time-dependent perturbative analysis of the parametrically driven system is used to determine specific resonance conditions for obtaining amplification and squeezing Resonant phenomena are evident when the parametric drive frequency ω is an integer divisor of either the sum or difference of the spin and cavity frequencies, i.e., ω = ωs ± ωcn, n ∈ N The fastest rate of amplification and squeezing is obtained under the resonance condition ω = ωc + ωs when the drive amplitude is maximal This occurs in the dispersive regime where ∆ = ωc − ωs ≫ g

Performance Metrics

The performance of the amplifier is characterized by several metrics, including amplification and noise temperature The rate of amplification is of the order of dB per microsecond, meaning that significant amplification occurs over thousands of periods of the parametric drive The steady-state gain is given by Gss = (γc − γl)κ + k2/(γc + γl)κ − k2, where k is related to the rate of amplification generated by the spin modulation in the absence of any damping The noise temperature of the amplifier is calculated as Tamp = ħωc/kB ln 1/nadd + 1!−1 At room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization, the resulting added noise in photons at the amplifier input is nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250

Control Protocols

The paper shows that time-dependent control of the detuning between systems can be used to transform the two-mode squeezing (entanglement) between the systems into individual squeezing of each system A standard operation available in this two-mode system can be used to adjust the squeezing so that it achieves maximal two-mode squeezing, which means one of the maximally squeezed quadratures can be written as Q = 1/√2(xaXa + yaYa) + 1/√2(xbXb + ybYb) This transformation can be applied in two steps to convert any general two-mode squeezing into the squeezing of at least one of the oscillators

Experimental Realization

Implementing the hybrid parametric amplifier requires a microwave cavity with two resonant modes or, equivalently, two interlocking cavities each with one mode The trade-off between g and Q tends to follow g ∝ √1/Q For cryogenic regimes required for squeezing, higher quality factors are easily achieved, while superconducting stripline resonators achieve very high coupling rates and power conversion factors The primary challenge in implementing the hybrid paramp presented here lies in designing a single or dual microwave resonator that has two resonances

Conclusion

The non-degenerate paramp amplifies and squeezes both systems, and time-dependent control of the detuning between them can be used to transform the two-mode squeezing (entanglement) between the systems into individual squeezing of each system This provides a means to squeeze the collective state of an NV ensemble The paper concludes by discussing distinct potential applications, including room temperature quantum limited microwave amplifiers and the generation of entanglement between an ensemble and a microwave field

Appendix A

The noise temperature of the amplifier is calculated by replacing the parametric drive with a non-degenerate parametric amplifier and solving for the steady-state of the resulting linear two-mode system The noise added by the parametric amplifier at the input is Nadd = nadd + 1/2, where nadd = η(γ1/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[η + k2/√gκ - γl/γ]2−1/2 The noise temperature is then obtained by calculating the added noise at the output an diving it by amplifier gain This gives us nadd = (γc/γ!) (γ1/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is Tamp = ħωc/kB ln 1/nadd + 1!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K The noise temperature is essentially the same as that of the maser amplifier demonstrated in [14]

The rate of amplification in decibels is dB = d/dt h 10 log10 e kt/2 i = 5k log10 (e) ≈ 2.2k The steady-state gain is Gss = (γc − γl)/γ + k2/√gκ(1 - k2/√gκ2) The system becomes unstable once k ≥ √κγ The noise added by the parametric amplifier at the input is Nadd = S(V)G2ss = κ2γcγl(2nT + 1) + k2γcκ(2ns + 1)[k2 − γκ]2/2 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γ1/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.5 GHz and the spins pumped to 80% polarization The noise temperature is Tamp = 150 K This gives the resulting value of nadd ≈ 1/2nT + ns + 1/4 ≈ 1/2nT = 1250 The noise temperature is Tamp = nadd + 1/2, where nadd = η(γc/γ)(2nT + 1) + k2/ (gκ)(2ns + 1)[(γc − γl)/γ + k2/gκ]2−1/2 The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of ns in terms of the spin polarization is ns = 1/2(1 - P P) The noise temperature is T = ħωc/k ln 1 + P P!−1 This gives the resulting value of nT = 2500 at room temperature (300 K) with ωc = 2.

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Amplification of microwave signals in spin ensembles can be achieved purely by applying an oscillating magnetic field to parametrically drive the spin ensemble, which is a key mechanism for room temperature signal processing. This allows AI systems to utilize NV ensembles as amplifiers for various signals stored within them.

  2. Generation of two-mode squeezing between a microwave cavity mode and an ensemble of spins can be transformed into simultaneous single-mode squeezing of both systems using time-dependent control protocols involving detuning and resonant interaction with the collective spin/cavity coupling. This capability enables the generation of highly correlated quantum states useful for advanced sensing or communication applications.

  3. The system allows for the transformation of any two-mode quadrature into the squeezing of at least one oscillator by applying a time evolution under a specified detuning followed by an evolution under the interaction between oscillators, which can be controlled to achieve maximal two-mode squeezing. This provides a method to adjust the degree of entanglement in quantum states for specific computational needs.

  4. The analysis shows that in the far off-resonant regime with respect to the cavity mode, NV centers shift the cavity frequency, modulating it and thus amplifying signals at rates scaling as R proportional to g squared over delta. AI systems can leverage this relationship to predict optimal driving parameters for maximizing amplification and squeezing in dispersive regimes.

  5. The derived noise temperature formula nadd includes terms dependent on the spin temperature ns and cavity temperature nT, showing that the noise added by the amplifier depends on these thermal factors. This allows AI systems to accurately estimate the noise floor of a quantum amplifier operating at different temperatures, from cryogenic regimes up to room temperature.

Abstract

We introduce an implementation of a non-degenerate parametric amplifier in which the signal and idler modes, respectively, a microwave mode and an ensemble of spins (e.g., nitrogen-vacancy centers in diamond), are operated in their linear regime. This paramp, which amplifies signals in both parts at room and cryogenic temperatures, can be used to generate both the two-mode and single-mode squeezing of either system. It requires merely modulating the frequency of the spin ensemble at the sum of the cavity and spin frequencies (providing the classical pump) with the two systems sufficiently detuned. This effect is remarkable given that modulating a spin ensemble by itself produces neither amplification nor squeezing, unlike modulating an oscillator, and that an off-resonant perturbative analysis would suggest that modulating the spin ensemble merely parametrically drives the cavity mode. With typical cavity parameters including a cavity quality factor Q=10 4, and a 1 GHz modulation amplitude, the microwave signal can be amplified by approximately 18 dB in 1.7 μ s, with a resonant bandwidth of about 0.5 MHz. At 10 mK with the same modulation amplitude and a cavity and spin Q=5 times 10 4 it generates approximately 5 dB of squeezing. We also examine the experimental requirements for implementation.

Sources

Related papers