Ultrafast Meissner-Levitated Microrotor

arXiv:2509.24964 · quant-ph, cond-mat.mes-hall · Submitted 2025-09-29 · Read on arXiv

Listen

Radio episode about this paper

Transcript

Introduction to the show: ident: Quantum Radio. Generated commentary on the latest quantum physics and condensed matter papers.

Kai: I'm Kai.

Mira: And I'm Mira, here with Lev.

Kai: We're looking at the paper: "Ultrafast Meissner-Levitated Microrotor".

Mira: Here's the gist of the paper. Magnetically levitated spinning rotors are key elements in important technologies such as navigation by gyroscopes, energy storage by flywheels, ultra-high vacuum generation by turbomolecular pumps, and pressure sensing for process control.

Kai: The authors demonstrate wide range pressure sensing by a spinning rotor based on a micromagnet levitated by the Meissner effect at 4.2 Kelvin.

Mira: They achieve rotational speeds of up to 138 million rotations per minute, resulting in very high effective quality factors, outperforming current platforms.

Kai: System Setup and Operation The experimental setup involves a hard ferromagnetic sphere made of a rare-earth alloy levitated in a cylindrically symmetric trap made of a type I superconductor.

Title and authors: Kai: So we're looking at this paper called "Ultrafast Meissner-Levitated Microrotor". It’s about using a spinning magnet levitated by the Meissner effect to sense pressure.

Mira: Yeah, it sounds like they're pushing the boundaries of what's possible with magnetic rotors in cryogenic environments. It really focuses on making this sensing mechanism work at very low temperatures, specifically four point two Kelvin.

Lev: From a hardware standpoint, I’m interested in how stable that levitation is supposed to be when you’re dealing with these superconducting traps and the magnetic sphere.

Kai: Well, they describe it using a hard ferromagnetic sphere made of a rare-earth alloy being levitated in a cylindrically symmetric trap made of a type one superconductor, which relies on the Meissner repulsion between them.

Mira: And they model that interaction by thinking about it as a dipole dipole interaction between the magnetic moment of the sphere and an image dipole. That's how they get the levitation to be stable.

Lev: That modeling is important because it tells us what kind of forces are actually at play, which helps us figure out how much noise we’re dealing with when we try to use this for anything else, right?

Kai: Exactly. And then they show a detection system using a dc sQUID flux sensor via a superconducting pick-up coil to measure the motion, and they use driving coils to actuate it.

Mira: So they are coupling the magnetic motion with superconducting electronics to get a readout of the rotation, which is pretty standard for sensitive measurements in this field.

Lev: And operating everything in a cryogenic vacuum chamber dipped in liquid helium at four point two Kelvin puts them right where we have to worry about thermal noise, which I know is always the first hurdle.

Kai: Right, and that leads into how they use it as a pressure sensor by measuring the decay rate of its angular velocity, similar to conventional spinning rotor gauges.

Mira: They're using that relationship where gas pressure is proportional to the rotational drag induced by the gas, which is what makes it a gauge.

Lev: And they give us a specific formula for that decay rate in the low-pressure free molecular regime, saying gamma equals ten over pi times P times rho times v over R bar.

Kai: So that damping rate directly measures the pressure P of the gas where the magnetic rotor is located, which is what makes it a pressure sensor.

Mira: And then they show how effective this system is for sensing in a wide range of pressures, from ten to eight mbar, which covers a pretty broad area.

Lev: That's good because it shows the operational range before we worry about pushing the physical limits of the setup.

Kai: The paper also gives us some really impressive numbers for their performance, showing that their quality factor Q is one point three three times ten to the power of thirteen, which is way higher than anything reported in mechanical resonators.

Mira: That high quality factor is what makes this system so promising; it means very little energy dissipation when we are trying to measure the pressure.

Lev: And they also give us some sensitivity limits, showing that their thermal torque noise limited sensitivity for pressure is two point five times ten to the negative eleven p a per root hertz.

Kai: That number is quite low, and they also have this SQUID readout limited pressure sensitivity of one point nine times ten to the negative twenty three p a per square root hertz.

Mira: So that means we’re looking at incredibly small pressure changes that we can detect with this setup, which is what makes it interesting for process control applications.

Lev: The caveat there is that the thermal noise limited sensitivity depends on the measurement record and the quality factor, so if those things drop, that sensitivity goes up too.

Kai: And they also mention how this system could be used for fundamental physics because of its ultralow thermal torque noise.

Mira: They suggest it can operate as an ultrasensitive torque based magnetometer with a resolution of one times ten to the negative sixteen tesla per square root hertz, which is pretty low.

Lev: If you want to probe ultralight dark matter models, that sensitivity could be useful for those specific ranges of frequency from one hundred to seven thousand hertz.

Kai: They also mention that the system allows for investigating quantum field effects associated with fast rotational motion.

Mira: So they’re not just looking at pressure; they're also opening up a door to exploring how quantum mechanics plays out when you have something spinning at these high speeds.

Lev: Before we wrap up this part, I think the main thing is that the thermal noise floor is so low, it opens up possibilities beyond just sensors.

Kai: Yeah, and it really highlights how far we've come in terms of achieving very fast and very low dissipation magnetic microrotors at cryogenic temperatures.

Mira: So to summarize this paper on "Ultrafast Meissner-Levitated Microrotor", they’ve demonstrated a novel way to sense pressure across a wide range from ten to eight mbar, with a quality factor Q of one point three three times ten to the power of thirteen.

Lev: The key takeaway for us is that the thermal noise limited sensitivity for pressure is two point five times ten to the negative eleven p a per root hertz, which opens up possibilities in both applied sensing and fundamental physics.

Kai: And they also point out that because of this ultralow thermal noise, it provides an opportunity for ultrasensitive torque based magnetometry at one times ten to the negative sixteen tesla per square root hertz.

Mira: So we have a system that's performing better than mechanical resonators in terms of quality factor, and it shows potential for much deeper probing into fundamental physics if we can maintain this noise level.

Lev: The limitation they mention is that the process limited uncertainty for pressure depends on several factors, including the SQUID readout floor and the thermal torque floor.

Kai: Exactly, so if we want to really use this for precision measurements, we have to figure out how to minimize those floors as much as possible.

Mira: It’s a solid piece of experimental work that pushes the limits on dissipation in magnetic rotors at these temperatures.

Lev: We'll take a quick break and then talk about what improvements they suggest for this system, because they did mention some ways to push those numbers further.

The paper's summary: Kai: So, to wrap up this talk on the "Ultrafast Meissner-Levitated Microrotor," they’ve basically shown they can use these tiny spinning magnets at super cold temperatures, four point two Kelvin, to sense pressure across a huge range of pressures.

Mira: Yeah, that’s the main takeaway—they're not just measuring one thing; they're demonstrating this sensor capability over a wide span from ten to eight mbar.

Lev: And they achieved a quality factor of one point three three times ten to the power of thirteen, which is pretty high for something like this, and that means very low energy loss when we are trying to measure those pressure changes.

Kai: That high quality factor is what really stands out because it shows they’ve managed to keep dissipation down in this kind of setup.

Mira: And the sensitivity numbers they put forward are pretty telling—the thermal torque noise limited sensitivity for pressure is two point five times ten to the negative eleven p a per root hertz.

Lev: That thermal noise floor is what we need to worry about when we try to run this on real hardware, because you want that kind of low noise level to be achievable.

Kai: But they also showed how this system can be used for something beyond just pressure sensing—it can work as an ultrasensitive torque based magnetometer with a resolution of one times ten to the negative sixteen tesla per root hertz.

Mira: That sensitivity is what opens up the door for probing ultralight dark matter models, specifically in the frequency range from one hundred to seven thousand hertz.

Lev: If you want to probe those very low frequencies, you need that thermal noise floor to be as low as they claim, because otherwise the noise from their measurement itself will swamp anything else.

Kai: They also mentioned that this setup lets them investigate quantum field effects associated with fast rotational motion, which is pretty interesting for fundamental physics.

Mira: Exactly; it’s not just a pressure gauge anymore; it’s a platform to look at how things behave quantum mechanically when you have something spinning that fast.

Lev: That opens up new questions about the quantum nature of rotation itself, which is where things get really complex when you try to model the dynamics.

Kai: The whole point of this work is proving that we can build these ultra-fast, low-dissipation magnetic microrotors at cryogenic temperatures and use them for both practical sensing and deep physics measurements.

Mira: It's a solid demonstration of how magnetic levitation, when done right with these superconducting traps, can overcome some of the noise challenges we usually face in quantum systems.

Lev: But the caveat is that you still have to worry about those readout floors and the thermal torque floor mentioned earlier—you can’t just assume perfect performance.

Kai: So, while they've shown a lot of potential, the next step is really figuring out how to minimize those process limited uncertainties so we can use this for actual precision applications.

Mira: Right, so it’s a really promising piece of experimental work that pushes the limits on dissipation in magnetic rotors at these temperatures.

Lev: Yeah, and before we get into how they suggest pushing those numbers further, let's talk about what else is going on with this material science characterization idea they mentioned earlier.

The paper's improvements: Tom: So we're looking at how they suggest improving this system for future work on the "Ultrafast Meissner-Levitated Microrotor."

Kai: They’re talking about pushing those spinning frequencies higher, getting them up to two point three mega hertz and maybe even higher.

Mira: And they link that high frequency capability directly to probing fundamental quantum aspects of spins, especially at frequencies above one mega hertz with a thermal noise limited resolution of one times ten to the negative sixteen tesla per root hertz.

Lev: That sensitivity for magnetometry at that frequency range suggests they could start looking into things like ultralight dark matter models in the range from one hundred to seven thousand hertz.

Kai: It’s interesting because it moves us from just sensing pressure to using this thing as a tool for extremely sensitive magnetic measurements.

Mira: They also touch on material science characterization, suggesting the system could be used to observe how ferromagnetic properties or tensile strength behave under extreme mechanical stress by watching the material break down.

Lev: So they’re not just about measuring things; they’re looking at the physical limits of what these materials can handle before they disintegrate, which is a different kind of engineering problem.

Kai: The implication there is that this setup isn't just for sensors or physics; it could be used to test the fundamental limits of matter itself under stress.

Mira: That’s a big shift because it connects the quantum behavior we see in the rotor to how heavy materials respond when you apply extreme forces.

Lev: The caveat here is that they give an estimated maximum frequency around five point five mega hertz for a particle with a radius of thirty micrometers, so it's not infinite freedom there.

Kai: So, while they’re pushing the limits on what the rotor can do physically, the next challenge is still managing all those noise floors we talked about before.

Mira: It seems like they are trying to achieve a balance between pushing into new physics territory and keeping the hardware stable enough to get reliable measurements.

Lev: Before we look at how they plan to tackle those noise floors, let's talk about what the specific readout systems need for this kind of high-speed operation.

Conclusion: Kai: So to wrap up this talk on the "Ultrafast Meissner-Levitated Microrotor," they’ve shown that we can build these tiny spinning magnets at super cold temperatures and use them for both sensing pressure across a wide range and probing fundamental quantum aspects.

Mira: Exactly; it’s a solid demonstration of how magnetic levitation, when done right with these superconducting traps, can overcome some of the noise challenges we usually face in quantum systems.

Lev: The key point is that they've managed to keep dissipation down in this kind of setup, which is what makes this system promising for any real hardware implementation.

Kai: And the thermal noise floor they achieved, two point five times ten to the negative eleven p a per root hertz, gives us a baseline for how sensitive we can actually get with these devices.

Mira: It opens up possibilities in both applied sensing and fundamental physics, especially when you look at that sensitivity for dark matter probing in the frequency range from one hundred to seven thousand hertz.

Lev: That’s a big idea because if we can maintain that noise level, it changes how we think about what kind of precision measurements are feasible with these rotating systems.

Kai: The whole point of this work is proving that we can build these ultra-fast, low-dissipation magnetic microrotors at cryogenic temperatures and use them for both practical sensing and deep physics measurements.

Mira: It’s a really promising piece of experimental work that pushes the limits on dissipation in magnetic rotors at these temperatures.

Lev: But the caveat is that you still have to worry about those readout floors and the thermal torque floor they mentioned earlier—you can’t just assume perfect performance.

Kai: So, while they've shown a lot of potential, the next step is really figuring out how to minimize those process limited uncertainties so we can use this for actual precision applications.

Mira: It seems like they are trying to achieve a balance between pushing into new physics territory and keeping the hardware stable enough to get reliable measurements.

Lev: Before we look at how they plan to tackle those noise floors, let's talk about what the specific readout systems need for this kind of high-speed operation.

Joel K Jose, Andrea Marchese, Marion Cromb, Hendrik Ulbricht, Andrejs Cebers, Ping Koy Lam, Tao Wang*, Andrea Vinante*

Quantum Innovation Centre (Q.InC) · Agency for Science Technology and Research (A*STAR) · Institute of Fotonica e Nanotecnologie IFN-CNR · Fondazione Bruno Kessler (FBK) · School of Physics and Astronomy, University of Southampton · MMML lab, Department of Physics, University of Latvia · Centre of Excellence for Quantum Computation and Communication Technology, The Department of Quantum Science and Technology, Research School of Physics, The Australian National University

quant-ph, cond-mat.mes-hall

Submitted: 2025-09-29

Updated: 2026-11-09

Comments: 22 pages, 12 figures (including SM)

Journal ref: Joel K Jose, Andrea Marchese, Marion Cromb, Hendrik Ulbricht, Andrejs Cebers, Ping Koy Lam, Tao Wang, Andrea Vinante, Science Advances 12, aee6434 (2026)

DOI: 10.1126/sciadv.aee6434

License: http://arxiv.org/licenses/nonexclusive-distrib/1.0/

Importance score: 83/100

The gist: Magnetically levitated spinning rotors are key elements in important technologies such as navigation by gyroscopes, energy storage by flywheels…

Key concepts

Meissner Effect
This phenomenon occurs when a superconductor expels magnetic fields from its interior. In this setup, the superconducting trap repels the magnetic sphere, creating stable levitation without physical contact. This repulsion is modeled using dipole-dipole interactions between the sphere's magnetic moment and an image dipole.
Spinning-Rotor Gauge (SRG)
The rotor acts as a pressure sensor by measuring how quickly its rotational speed decays when subjected to gas drag. The decay rate is directly proportional to the external gas pressure, allowing researchers to measure minute changes in pressure with high precision.
Quality Factor (Q)
The quality factor measures the energy stored in the rotor versus the energy lost per cycle. A very high Q indicates low dissipation and high sensitivity. The achieved Q of 1.33 x 10^13 is significantly higher than any mechanical resonator reported, signifying extremely low damping.

Terminology

Summary

Magnetically levitated spinning rotors are key elements in important technologies such as navigation by gyroscopes, energy storage by flywheels, ultra-high vacuum generation by turbomolecular pumps, and pressure sensing for process control. p. 0 The authors demonstrate wide range pressure sensing by a spinning rotor based on a micromagnet levitated by the Meissner effect at 4. p. 02 Kelvin. They achieve rotational speeds of up to 138 million rotations per minute, resulting in very high effective quality factors, outperforming current platforms. p. 0

System Setup and Operation

The experimental setup involves a hard ferromagnetic sphere made of a rare-earth alloy levitated in a cylindrically symmetric trap made of a type I superconductor. Stable levitation relies on the Meissner repulsion between the magnetic sphere and the superconducting trap, which can be modeled by a dipoledipole interaction between the magnetic moment of the sphere and an image dipole. p. 1 The motion is detected by a dc SQUID flux sensor via a superconducting pick-up coil, and actuated by a pair of driving coils. p. 1 The setup operates in a cryogenic vacuum chamber dipped in liquid helium at T = 4. p. 12 K.

Pressure Sensing Mechanism

The rotor can be operated as a cryogenic pressure sensor by measuring the decay rate of its angular velocity, similarly to conventional Spinning-Rotor Gauges (SRG). SRGs exploit the proportionality between gas pressure and rotational drag induced by the gas. p. 1 The decay rate is given by γ = 1/τ, and in the low-pressure free molecular regime is given by γ = 10/π P ρvR¯. p. 3 This damping rate is a direct measurement of the pressure P of the gas at the location of the magnetic rotor. p. 3

Performance and Limits

The experiment shows that our levitated spinning rotor can be effective as a pressure sensor in a wide range of pressures, from 10−3 mbar to 10−8 mbar. The quality factor Q is obtained as Q = πf /γ = 1. p. 433 × 10 13, which is far higher than the Q of any mechanical resonator reported in the literature. p. 4 The fundamental thermal noise-limited sensitivity of a SQUID readout is estimated at δPReadout = 1. p. 69 × 10−23 Pa/√Hz, and a thermal (torque) noise-limited sensitivity is δPProcess = 2. p. 65 × 10−11 Pa/√Hz.

Fundamental Physics Prospects

The ultralow thermal torque noise ensures extremely low levels of thermal noise and opens the way to various precision measurements of interest to fundamental physics. A levitated ferromagnet can be operated as an ultrasensitive torque-based magnetometer with a resolution of 1 × 10−16 T/√Hz, allowing probing ultralight dark matter models. p. 6 The system also allows for the investigation of quantum field effects associated to fast rotational motion. p. 6

Conclusion

In conclusion, we have demonstrated ultrafast and ultralow dissipation magnetic microrotors operating at cryogenic temperature, featuring spinning frequencies higher than 2.3 MHz and damping lower than 10−6 Hz. p. 7 We have demonstrated the use as a novel cryogenic pressure sensor with wide range. p. 7 In the long term, because of the ultralow thermal noise, this system opens the way to a number of exciting opportunities in the context of fundamental and quantum science. p. 7

Symbols & Units

The table defines symbols such as t time s, omega(t) mean (deterministic) angular velocity rad s−1, and P pressure Pa. The process-limited uncertainty for pressure is given by σP (tm) ≥ max [1/γP s(1/2) 12 σ 2v r t 3m SQUID readout floor, 1/γP r Q tm thermal torque (process) floor]. p. 0 The relative uncertainty on pressure is proportional to 1/√P tm. p. 2 The thermal noise-limited sensitivity is δPProcess = 1/γ s squared kBT Iω 20 γtm. p. 6 The SQUID readout-limited pressure sensitivity is δPReadout = 1. p. 69 × 10−23 Pa/√Hz.

References

The references listed include works on high-Q magnetic levitation, absolute pressure and gas species identification with an optically levitated rotor, and studies on quantum spin stabilized magnetic levitation. The paper also cites works related to the spinning rotor gauge and fundamental physics investigations like probing the quantum nature of gravity through diffusion. p. 9 The acknowledgment section notes support from various programs including the QuantERA II Programme. p. 9 The methods section details the use of NdFeB spherical particles and a lead trap. p. 9 The supplementary information includes models for precession motion and the derivation of the Cramer-Rao Lower Bound. p. 6 The paper concludes by estimating the fundamental pressure sensitivity based on experimental parameters. p. 6

Methods

The magnets used are spherical microparticles made of a rare-earth alloy based on NdFeB [17] with a radius of about 24−30 µm. The pick-up and driving coils are made of NbTi wire with diameter 100 µm and wound onto a 3D printed polymeric support. p. 9 The pressure in the vacuum chamber is measured on the room-temperature side using a commercial Penning gauge. p. 9

Data Availability

All data supporting the findings of this study are available in the main text and Supplementary Information. Additional details can be obtained from the corresponding authors upon request. p. 1

Author Contributions

A.V. has conceived and supervised the experiment, developed earlier versions of the experimental setup together with H. p. 1U., and coordinated the experimental efforts together with T. p. 1W. and P.K.L. J.J has performed the first successful measurements and data analysis, M. p. 6C. and A.M have performed further refined measurements. p. 1 T.W derived the fundamental sensitivity limit of the MLSR gauge based on the Cram´erRao lower bound (CRLB). p. 6 A.C has developed the full dynamical model of the spinning magnet. p. 5

Competing Interests

The authors declare no competing interests.

Acknowledgment

A.V., M.C., H.U., and A.C acknowledge support from the QuantERA II Programme (project LEMAQUME) that has received funding from the European Union’s Horizon 2020 research and innovation programme under Grant Agreement No 101017733. p. 9 A.V. and A.M acknowledge financial support from the Italian Ministry for University and Research within the Italy-Singapore scientific and technological cooperation agreement 2023-2025. p. 9 T.W acknowledges support from ItalySingapore science and technology collaboration grant (R23I0IR042), Delta-Q (C230917004, Quantum Sensing). p. 9 P.K.L., T.W. and J.J acknowledges the support from the LeviNet under EPSRC International Quantum Technologies Network Grant EP/W02683X/1. p. 9 H.U. and M.C acknowledge support from UKRI EPSRC grant EP/W007444/1. p. 9

Green — the paper says it, and the page is printed. Red — no passage carries it, so treat that sentence as unverified. The same check runs on your own text: check a summary against its source, $5.

Improvements for AI systems

  1. Cryogenic Pressure Sensing Capability: The improved system can operate as a cryogenic pressure sensor in a wide range of pressures from 10 to 8 mbar, achieving a fundamental thermal (torque) noise-limited sensitivity of 2.5 x 10-11 Pa/sqrt(Hz).

  2. Ultra-High Frequency Sensing: The system can achieve spinning frequencies up to 2.3 MHz and potentially higher, allowing for probing fundamental quantum aspects of spins at frequencies above 1 MHz with a thermal noise-limited resolution of 1 x 10-16 T/sqrt(Hz).

  3. Fundamental Physics Probing: The system can be used as an ultrasensitive torque-based magnetometer with a thermal-noise-limited resolution of 1 x 10-16 T/sqrt(Hz), enabling the probing of ultralight dark matter models in the range of 10 squared to 10 7 Hz.

  4. Material Science Characterization: The system can be utilized for characterizing ferromagnetic properties or tensile strength under extreme mechanical stress by observing material disintegration limits, with an estimated maximum frequency around 5.5 MHz for a particle with radius R = 30 µm.

Sources

Related papers