Affordable Data Collection System for UAVs Taxi Vibration Testing

summary

The gist

Structural vibration testing plays a key role in aerospace engineering for evaluating dynamic behaviour…

In short

This work designed and built an affordable, in-house acceleration data acquisition system for aerospace vibration testing using a small fixed-wing UAV. The system integrates multiple Orange Pi 3 boards with several LSM6DS3TR-C MEMS sensors under a Python master/slave architecture. Testing on the UAV confirmed the system reliably captures consistent multi-sensor acceleration data and repeatable Power Spectral Density profiles, proving it is a cost-effective alternative to commercial DAQs.

Key concepts

Master–Slave Architecture
This software structure divides the control of the data acquisition system into a central 'master' unit and several 'slave' units. The master unit manages global test controls and organizes all collected datasets, while the slave modules handle continuous sensor polling. This distribution allows for scalable management of multiple sensors without overloading a single component.
MEMS Inertial Measurement Units (IMUs)
These are small, highly sensitive electronic sensors used to measure acceleration and motion. The LSM6DS3TR-C units in this system are integrated with the Orange Pi 3 SBC. They capture high-quality dynamic behavior data from the UAV, which is essential for structural vibration analysis.
Power Spectral Density (PSD)
PSD is a mathematical tool used to analyze vibration data by showing how much of the total vibration energy is present at different frequencies. By using Welch's method on the acquired acceleration data, researchers can create a profile that reveals which specific frequencies are causing structural vibrations in the aircraft.

Terminology used across episodes

This episode discusses

The paper

Affordable Data Collection System for UAVs Taxi Vibration Testing · Read on arXiv

Department of Aerospace Engineering, Universidad Carlos III de Madrid · Electronic Technology Department, Universidad Carlos III de Madrid

Structural vibration testing plays a key role in aerospace engineering for evaluating dynamic behaviour, ensuring reliability and verifying structural integrity. These tests rely on accurate and robust data acquisition systems (DAQ) to capture high-quality acceleration data. However, commercial DAQs that provide the required performance and features are often expensive and complex, limiting their accessibility for small-scale research and experimental applications. This work presents the design and experimental validation of an affordable and in-house-developed acceleration DAQ, tested on a small fixed-wing UAV through several Taxi Vibration Test (TVT) runs and ambient vibration measurements. The proposed system integrates several OrangePi 3 LTS single-board computers with multiple LSM6DS3TR-C MEMS inertial measurement units operating simultaneously via an Inter-Integrated Circuit (I2C) communication interface, managed under a Python-based master/slave architecture. Data is acquired at a stable sampling rate of approximately 208 Hz and post-processed using Welch's method to estimate their Power Spectral Density (PSD). Results confirm the system ability to provide consistent multi-sensor acceleration data and repeatable PSD profiles under the same test conditions; thus, demonstrating its reliability. With a total hardware cost below 600 EUR (approximately 690 USD), the developed DAQ offers a compact, scalable and cost-effective alternative for aerospace vibration analysis and structural testing.

DOI: 10.1115/SSDM2026-183328

Transcript

Introduction to the show: ident: Robotics Radio. Generated commentary on the latest robotics and control papers.

Rosa: I'm Rosa.

Dev: And I'm Dev, here with Taro.

Rosa: We're looking at the paper: "Affordable Data Collection System for UAVs Taxi Vibration Testing".

Dev: Here's the gist of the paper. Structural vibration testing plays a key role in aerospace engineering for evaluating dynamic behaviour, ensuring reliability and verifying structural integrity The proposed system integrates a SBC with multiple MEMS inertial measurement units operating concurrently under a Python-based master–slave software architecture With a total hardware cost below C600 (690), the developed DAQ offers a compact, scalable and cost-effective alternative for aerospace vibration analysis and structural testing System Design Philosophy The proposed data acquisition system is designed to provide a flexible and scalable solution for vibration testing in aerospace applications while maintaining a low overall cost The architecture follows a distributed master–slave configuration where multiple acquisition nodes manage local sensor management and data collection, coordinated by a central master unit This distributed approach allows for easy expansion or reduction of measurement points without altering the core functionality Hardware and Communication Strategy The core hardware consists of an Orange Pi 3 LTS SBC interfaced with multiple Adafruit LSM6DS3TR-C 6 degrees-of-freedom (DoFs) inertial measurement units (IMUs) To manage I2C address conflicts, an I2C multiplexer was introduced between the SBC and the IMU sensors This multiplexer enables selective prioritization of individual sensor channels while maintaining a single physical interface The final configuration considered includes a master and two slave modules, communicating with four IMUs each transmitting acceleration data in the x, y, and z axes Software Implementation Details Data acquisition is implemented through a distributed software framework ensuring stable sampling and synchronized configuration Each slave module performs continuous sensor polling, timestamping data locally to preserve temporal consistency across channels The master unit manages global test control and organizes datasets for subsequent post-processing The adopted direct polling approach was selected as a more reliable solution for ensuring consistent timing behaviour across multiple sensors Experimental Validation and Results The system was validated using a small fixed-wing UAV, the Ranger, subjected to Taxi Vibration Tests (TVTs) and Ambient Vibration Tests (AVTs) TVT results showed consistent spectral shapes with dominant vibration energy concentrated at low frequencies across multiple runs AVT results, conducted at rest, captured coherent frequency content even under low signal-to-noise conditions The comparison between TVT and AVT profiles confirms that the measured responses are governed by the excitation environment rather than artifacts of the acquisition system The developed DAQ system demonstrates that reliable vibration measurements can be achieved without relying on high-cost commercial Data Acquisition System (DAQ) platforms The total hardware cost remains below C600 (690), making it a practical and cost-effective alternative for structural vibration testing Future developments may focus on improving timing precision, increasing achievable sampling rates through optimized software, and extending the system to multi-axis and gyroscopic measurements The presented system represents a practical and cost-effective alternative for aerospace vibration testing The observed repeatability confirms that the proposed DAQ system provides reliable and repeatable acceleration measurements across multiple sensors and test conditions The consistency of the spectral content across repeated experiments validates the system's performance for structural vibration characterisation ACKNOWLEDGMENT The authors would like to thank Dr Francesco M.A.

Rosa: Mitrotta from the Department of Aerospace Engineering at the Universidad Carlos III de Madrid for helping out running the hereby reported testing campaign and providing the Volantex RC Ranger 2400 used This work has been supported by the Madrid Government (Comunidad de Madrid, Spain) under the Multiannual Agreement with the UC3M (IA aCTRl-CM-UC3M) REFERENCES

1: Dessena, G., Civera, M., Marcos, A., Chiaia, B., and Bonilla-Manrique, O.

Dev: E., 2026.

Rosa: “Multiple input tangential interpolation-driven damage detection of a jet trainer aircraft”.

Paper summary: Rosa: So this paper talks about this affordable data collection system for UAVs taxi vibration testing. Basically it claims that we don't need those expensive commercial DAQs to get good acceleration data for structural testing.

Dev: Exactly, the core idea is to build something in-house that is cheap and compact, which is what motivates the whole thing because commercial solutions are often too costly and complex for small research projects or experimental platforms three <ref:2601.07783#pg2>.

Rosa: They designed this system using a single board computer with multiple MEMS inertial measurement units operating at the same time through an I2C communication interface.

Taro: So it's about integrating the sensor network design to prioritize scalability and ease of installation, so you can add more sensors later by extending the multiplexer channels or adding more slave modules <ref:2601.07783#pg3>.

Dev: The paper presents this system as an affordable acceleration data acquisition system intended specifically for aerospace vibration testing applications <ref:2601.07783#pg2>. It focuses on using Single-Board Computers and MEMS based inertial sensors to open up new options for vibration analysis.

Rosa: The thesis is that you can achieve reliable, repeatable measurements without the high cost barrier, by using this in-house developed setup tested on a small fixed-wing UAV through Taxi Vibration Tests and ambient vibration measurements <ref:2601.07783#pg1>.

Taro: It shows that this architecture allows for multiple identical inertial measurement units to operate concurrently without needing hardware address modification or extra communication interfaces, which simplifies things significantly <ref:2601.07783#pg3>.

Dev: The system is configured with a master and two slave modules communicating over wireless links using Internet Protocol over WiFi <ref:2601.07783#pg3>. They also implemented a distributed software framework to ensure stable sampling and synchronized configuration <ref:2601.07783#pg3>.

Rosa: The paper is interested because it shows that even with this low-cost setup, you can still capture the high-quality acceleration data required for identifying dominant vibration modes and validating structural models through Taxi Vibration Tests and Ambient Vibration Tests <ref:2601.07783#pg2>.

Conclusion: Dev: So looking at the title of "Affordable Data Collection System for UAVs Taxi Vibration Testing" and who wrote it, we see this is a practical solution for researchers and experimental platforms that don't have big budgets <ref:2601.07783#pg1>.

Rosa: It really comes down to showing that you can get reliable vibration measurements without depending on those high-cost commercial Data Acquisition Systems <ref:2601.07783#pg2>. The hardware cost is presented as being below six hundred euros, which makes it a very accessible alternative for aerospace vibration analysis <ref:2601.07783#pg1>.

Taro: What this means for us is that we can get repeatable acceleration measurements across multiple sensors and test conditions, and the consistency of the spectral content across repeated experiments validates the system's performance for structural vibration characterisation <ref:2601.07783#pg1>.

Dev: It also confirms that a distributed master-slave configuration with this setup is a scalable way to manage sensor data collection without needing complex external hardware address modifications or extra interfaces <ref:2601.07783#pg3>.

Rosa: The paper is really interested because it demonstrates that we can achieve the consistency needed for structural characterisation using a system that is compact and cost-effective, which is a big deal for getting real experimental data in this field <ref:2601.07783#pg1>.

More episodes

← Home