Transmitter Noise Propagation in Millimeter-Wave and Sub-Terahertz: From Limits to Design Guidelines

summary

The gist

This paper presents a comprehensive link budget analysis for millimeter wave (mm-Wave) and sub-Terahertz (subTHz) communication systems with primary focus on transmitter (TX) noise propagation…

In short

This analysis examines transmitter (TX) noise in mm-Wave and sub-THz systems, a factor often ignored when path loss is low. The study shows TX noise is amplified by component noise figures, increasing significantly with frequency. This propagated TX noise limits achievable Signal-to-Noise Ratio (SNR) by 15 to 25 dB at short distances, establishing fundamental performance ceilings below 10 cm.

Key concepts

Transmitter Noise Propagation
This refers to how noise generated at the transmitter travels through the system and affects the received signal. It is crucial because in high-frequency bands, this noise is not just thermal but is amplified by component imperfections, making it a major limiting factor for short-range links.
Component Noise Figures
These figures describe how much noise a specific hardware part (like an amplifier or mixer) adds to the signal. The paper highlights that these figures worsen drastically as the frequency moves into the sub-THz range, potentially increasing by over 15 dB, which severely impacts overall system performance.
SNR Ceiling
The SNR ceiling is a fundamental limit on how strong a signal can be relative to noise in a given communication link. The paper finds that due to propagated TX noise at short distances (under 10 cm), the SNR cannot improve further, creating an unbreakable barrier for very close-range wireless communication.
Atmospheric Molecular Noise
This is a type of background noise originating from the atmosphere itself, specifically molecular interactions. Unlike thermal noise, this source must be considered for medium and long-range links alongside TX noise to fully model the total system impairment.

Terminology used across episodes

This episode discusses

The paper

Transmitter Noise Propagation in Millimeter-Wave and Sub-Terahertz: From Limits to Design Guidelines · Read on arXiv

Mahir Burak Usta, Didem Aydogan, Evgenii Vinogradov, Mohammad Shahmoradi, Eduard Alarcon, ř Sergi Abadal, ř Korkut Kaan Tokgoz

Sabancı University · NaNoNetworking Center in Catalunya (N3Cat) · Universitat Politecnica de Catalunya

DOI: 10.1109/OJCOMS.2026.3730694

Transcript

Introduction to the show: ident: Electrical Engineering. The day in electrical engineering: signals, systems and the hardware that carries them.

Rosa: I'm Rosa.

Dev: And I'm Dev, here with Taro.

Rosa: We're looking at the paper: "Transmitter Noise Propagation in Millimeter-Wave and Sub-Terahertz".

Dev: Here's the gist of the paper. This paper presents a comprehensive link budget analysis for millimeter wave (mm-Wave) and sub-Terahertz (subTHz) communication systems with primary focus on transmitter (TX) noise propagation, an often overlooked impairment that can dominate in scenarios where path loss is insufficient to suppress TX noise below receiver thermal and atmospheric molecular noise levels.

Rosa: Core Findings on Noise Dominance The work demonstrates that TX noise is amplified by component noise figures that degrade significantly with frequency, rising from single digits to more than 15 dB in the sub-THz range.

Dev: In the scenarios analyzed, this propagated TX noise reduces the achievable Signal-to-Noise Ratio (SNR) by approximately 15 to 25 dB at short distances, creating fundamental SNR ceilings at ranges below about 10 cm.

Rosa: The authors develop a systematic framework quantifying TX noise dominance conditions as functions of distance, frequency, and component parameters.

Paper summary: Rosa: So we’re looking at this paper today titled "Transmitter Noise Propagation in Millimeter-Wave and Sub-Terahertz: From Limits to Design Guidelines." It’s about how transmitter noise behaves in these super high frequencies.

Dev: Right, and the core idea is that this transmitter noise can actually end up dominating everything else when you're talking millimeter wave or sub-terahertz. It’s an impairment that people often overlook because path loss alone doesn't bring it down low enough to be below thermal or atmospheric noise levels at the receiver.

Taro: So, what they claim is that transmitter noise gets amplified by component noise figures which degrade pretty significantly as the frequency goes up. They say it jumps from single digits to more than fifteen dB in the sub-terahertz range <ref:2604.16020#pg1,from single digits to more than 15 dB in the sub>.

Rosa: That’s a big jump, and that amplification has real consequences for the system performance. The paper shows that this propagated transmitter noise can reduce the achievable signal-to-noise ratio by about fifteen to twenty five decibels at short distances.

Dev: And those reductions are serious because they create these fundamental SNR ceilings at very short ranges, specifically below about ten centimeters. That’s a tight constraint for any system design in that range.

Taro: So, the framework they develop is meant to quantify exactly when this transmitter noise becomes dominant based on distance, frequency, and component parameters. It sets up a systematic way to see those dominance conditions across different settings.

Rosa: It gives us a concrete way to look at where the performance limits are being hit for these next-generation wireless systems. They also suggest that for short-range communication, you really need the transmitter noise figure to be as low as possible.

Dev: And they add that for medium and long-range links, you have to consider both the transmitter noise and the atmospheric molecular noise together in your design. That changes how you approach different link budgets entirely.

Taro: So, it sounds like it’s not just about one thing; it’s about mapping out a whole landscape of noise sources across different distances and frequencies.

Rosa: Exactly, because understanding where that propagated transmitter noise hits those SNR ceilings at less than ten centimeters is crucial for designing practical devices. It moves the discussion from just looking at the path loss to considering this internal component behavior.

Dev: And since they integrate thermal noise, atmospheric molecular noise, and this new propagated TX noise into one unified high frequency noise framework, it gives designers a complete picture of the total noise floor.

Taro: I’m interested in how this relates to what happens when the world misbehaves—for instance, if you're testing outside the lab environment where you can control component parameters precisely. How does that framework hold up when things get messy?

Paper summary: Rosa: That’s a good point, Taro. The paper itself focuses heavily on developing an explicit model for tracing that impact from the component level noise figures through the wireless channel propagation all the way to the receiver input.

Dev: And they derive a closed form analytical threshold that tells you precisely when this propagated transmitter noise takes over performance. That mathematical description is what makes it useful for real-time loop analysis, where you need to know exactly how fast things are changing.

Taro: So, if we’re thinking about a system that needs to recover gracefully when the channel conditions change unexpectedly, does this framework give us enough information on the failure modes?

Rosa: It gives us the limits of performance based on noise sources, which informs what kind of hardware you need to select. It points toward where you need to focus your optimization efforts for short-range links versus long-range links.

Dev: The paper itself flags that one limitation is that it develops a framework, but the actual implementation details for every single component are still dependent on those specific parameters they’re modeling. They aren't providing a plug-and-play solution yet.

Taro: So, the method is strong for defining the conditions, but you still need to input all that hardware data to get a final design result?

Rosa: Precisely. It’s a tool for quantifying dominance conditions rather than a final link budget calculation that spits out an SNR number directly without all those inputs.

Dev: And it really pushes the design guideline aspect by showing you exactly where the focus needs to be—lowering that TX noise figure for close range, and then balancing it against atmospheric molecular noise further out.

Taro: For someone who only listens to this, what does this paper mean practically? It means that in millimeter wave and sub-terahertz communication, you can’t just assume path loss is the only thing limiting your signal quality; you have to account for these internal transmitter noise characteristics too.

Rosa: It means that for short distances, under ten centimeters, your system's performance ceiling isn't set by the signal strength between towers anymore; it’s set by how noisy the transmitter itself is.

Dev: And for medium and long ranges, you have to manage a trade-off between keeping that transmitter noise figure low enough for short links and managing the atmospheric molecular noise you’re going to encounter over longer distances.

Taro: So, it shifts the focus from just maximizing transmit power or minimizing path loss to optimizing the internal characteristics of the transmitter itself based on where you need to operate.

Rosa: That's right. The paper provides that systematic framework for those design guidelines, showing designers exactly what noise sources are relevant at different ranges and frequencies in these high-frequency bands.

Conclusion: Rosa: So we’re wrapping up our look at this paper "Transmitter Noise Propagation in Millimeter-Wave and Sub-Terahertz: From Limits to Design Guidelines."

Dev: Yeah, it’s about how transmitter noise gets amplified in those super high frequencies, and how that affects the whole link budget.

Taro: It sets up a framework to figure out exactly when this noise starts dominating everything else.

Rosa: The authors are showing us that transmitter noise isn't just some small thing you can ignore anymore, especially at short ranges like under ten centimeters.

Dev: They quantify how much the signal-to-noise ratio drops, about fifteen to twenty-five decibels, because of this propagated noise.

Taro: It moves the focus from just path loss to considering the transmitter's internal noise figure and component parameters.

Rosa: So, what does this mean practically for people designing these next-gen wireless systems?

Dev: It means for short-range links, you gotta keep that transmitter noise figure as low as possible.

Taro: And for medium and long range links, you have to balance that with the atmospheric molecular noise too.

Rosa: The authors suggest this framework is a way to make those design choices systematic instead of just guessing.

Dev: They are giving engineers a clear map for where the performance limits actually lie in these bands.

Taro: It helps us see how gracefully a system can recover when the world gets messy with noise.

Rosa: This paper is basically about setting concrete rules for building reliable devices in millimeter wave and sub-terahertz communication.

Dev: But it still depends on you plugging in your own component specs to get the final numbers that matter for a real design.

More episodes

← Home