Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si) 13 H z Plates

summary

The gist

La-Fe-Si-based alloys are high potential candidates for a magnetic refrigerator based on the RMCE utilizing relatively low external magnetic field amplitudes…

In short

The research investigated the rotating magnetocaloric effect (RMCE) in a thin La(Fe,Mn,Si)13 alloy plate using external magnetic fields of 0.6 T and 1.0 T. The study found that the maximum rotating adiabatic temperature change reached 1.17 K at 1 T and 1.12 K at 0.6 T, with corresponding rotating isothermal entropy changes reaching up to $3.97 ext{ J K}^{-1} ext{ kg}^{-1}$ for a 1 T field.

Key concepts

Rotating Magnetocaloric Effect (RMCE)
This effect occurs when a magnetic field is rotated instead of simply being applied statically. The rotation creates a temperature change that is dependent on the direction of the magnetic field relative to the material's internal structure, allowing for more efficient cooling or heating cycles in a refrigerator.
Curie Temperature (T_C)
This is the critical temperature above which a ferromagnetic material loses its spontaneous magnetization and becomes paramagnetic. The researchers found that by tuning elements like Mn or Co, they could adjust this temperature to be near room temperature without significantly reducing the magnetocaloric effect.
Rotating Adiabatic Temperature Change ($Δ T_{ ext{rot}}^{ ext{ad}}$)
This measurement quantifies the temperature change experienced by the material when a magnetic field is rotated. It is a key metric for assessing how effectively the material can perform work or cooling cycles in a rotating magnetic refrigerator setup.
Rotating Isothermal Entropy Change ($Δ S_{ ext{rot}}^{ ext{iso}}$)
This value measures the change in entropy that occurs when the magnetic field is rotated while keeping the temperature constant. A higher value indicates a greater potential for energy conversion, which is crucial for designing high-performance magnetic refrigeration systems.

Terminology used across episodes

This episode discusses

The paper

Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si) 13 H z Plates · Read on arXiv

Rafael Almeidaa, Tomás Venturaa, Ricardo Moura Costa Pintoa, João Oliveira Silvaa, Konrad Loeweb, Rodrigo Kiefec, Ên Joáo Sequeira Amaralc, и Joе Pedro Araújoa, ␒ João Horta Beloa

IFIMUP – Institute of Physics for Advanced Materials, Nanotechnology and Photonics, Department of Physics and Astronomy, Faculty of Sciences of University of Porto · Vacuumschmelze GmbH & Co. KG · Physics Department and CICECO – Aveiro Institute of Materials, University of Aveiro

DOI: 10.1063/5.0339017

Transcript

Introduction to the show: ident: Condensed Matter. The day in condensed matter: materials, phases and the measurements under them.

Kai: We're looking at the paper: "Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si) 13 H z Plates".

Mira: Here's the gist of the paper. La-Fe-Si-based alloys are high potential candidates for a magnetic refrigerator based on the RMCE utilizing relatively low external magnetic field amplitudes, such as 0.6 T The work explores the rotating magnetocaloric effect (RMCE) present in a 0.27 mm thin plate of sintered and hydrogenated La(Fe,Mn,Si)13 Material Development and Tuning The alloys based on La-Fe-Si and Mn-Fe-P-Si stand out due to the high tunability of their Curie temperature through slight changes of element fractions, allowing the design of layered active magnetic regenerators (AMR) Hydrogenation could increase the Curie temperature of the alloys to 280-340 K without negatively impacting magnetocaloric properties Partially substituting Fe with Co could increase TC beyond room temperature without hydrogenation while reducing hysteresis, at the "cost" of gradually decreasing the intensity of the MCE By combining partial hydrogenation and Co substitution, one could tune the TC to room temperature while maintaining a considerable MCE Finally, it was found that by substituting Fe for Mn, the TC could be tuned without significantly impacting the MCE Experimental Setup and Measurements The adiabatic temperature change, ΔTad, and rotating adiabatic temperature change, ΔTrot ad, exhibited when applying or rotating an external magnetic field with constant intensity (0.6 T or 1.0 T), were directly measured with a type-K thermocouple of 75 μm-wire diameter The measurements were performed under vacuum (P < 10-4 mbar) using a Halbach cylinder providing 1.0 T and another for providing 0.6 T Magnetization measurements were performed in a smaller piece (13.8 mg) of the same original sample using an MPMS3 SQUID magnetometer by Quantum Design Results of Magnetic Effects The maximum rotating adiabatic temperature change (ΔT rot ad) was found to be 1.17 K with the rotation of a 1 T magnetic field and 1.12 K when rotating a 0.6 T magnetic field Magnetostatic simulations revealed a considerable rotating isothermal entropy change (ΔS rot iso), reaching 3.97 J K−1 kg−1 for 1 T and 3.68 J K−1 kg−1 for 0.6 T The maximum ΔS rot iso obtained was 3.97 J K−1 kg−1, for 1.0 T Analysis of Field Dependence and RMCE The relative intensity of the RMCE with respect to the MCE at the high demagnetization orientation is further accentuated The maximum ΔT rot ad observed was 1.17 K, for 1.0 T Reducing the magnetic field intensity by 40%, to 0.6 T, resulted in a maximum ΔT rot ad of 1.12 K, 96% of what was observed for 1.0 T The maximum ΔS rot iso obtained for 0.6 T was 3.68 J K−1 kg−1, 7% less than with 1.0 T, despite the 40% reduction in applied field intensity The maximum ΔS rot iso observed was 3.97 J K−1 kg−1, for 1.

Paper summary: Kai: To start off with this paper on "Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si)thirteen H z Plates," the core thesis is that these La-Fe-Si based alloys are highly promising for magnetic refrigeration because they can operate at room temperature using relatively low external magnetic field amplitudes <ref:2601.23056#pg1,Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si>.

Mira: They are specifically exploring the rotating magnetocaloric effect within a two seventy millimeter thin plate of sintered and hydrogenated La(Fe,Mn,Si)thirteen to see what that effect looks like in practice <ref:2601.23056#pg1,thin plate of sintered and hydrogenated La(Fe,Mn,Si)13>.

Lev: The main claim seems to be that this material system allows for the design of layered active magnetic regenerators, or AMRs, which is a scalable technique for magnetic refrigerators.

Kai: Beyond just the rotation part, they discuss how tuning the composition of these alloys through hydrogenation or cobalt substitution lets them control the Curie temperature to get it into a usable range.

Mira: They found that hydrogenation can boost the Curie temperature to between two eighty and three hundred forty kelvin without hurting how good their magnetocaloric properties are.

Lev: And they also noted that substituting iron with cobalt can raise the Curie temperature past room temperature while also reducing hysteresis, though this comes at a cost of slightly decreasing the magnetocaloric effect intensity.

Kai: So, the practical takeaway is that you can combine those two tuning methods—hydrogenation and cobalt substitution—to hit room temperature operation while keeping a reasonable magnetocaloric effect.

Mira: They also found that substituting iron with manganese allows them to tune the Curie temperature without significantly hurting the magnetocaloric effect either, which is useful for design flexibility.

Lev: The implications are that these alloys, when manufactured using powder metallurgy to create sub-millimeter features in dense three dimensional structures, can optimize heat transfer and pressure drop within those AMRs.

Kai: That’s the engineering angle—the ability to build these structures with sub-millimeter features while maintaining good thermal performance.

Mira: Ultimately, the paper is pointing toward using these materials for next-generation magnetic refrigerators because they address both high operating temperature potential and manufacturability challenges.

Conclusion: Kai: So looking at the full picture of this work on "Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si)thirteen H z Plates," the focus is really on proving that this specific material platform works for magnetic cooling applications <ref:2601.23056#pg1,Rotating Magnetocaloric Effect in Sintered La(Fe,Mn,Si>.

Mira: The authors are demonstrating how precise material engineering—using hydrogenation and element substitution—allows them to precisely target the Curie temperature for practical use in a refrigerator.

Lev: It boils down to showing that you can get a material that’s both magnetocalorically active and chemically tunable enough to be useful in a device like an AMR.

Kai: What this means for the world is that we have a pathway toward creating compact magnetic refrigerators using these materials at temperatures achievable with low magnetic field amplitudes.

Mira: It moves the conversation from just finding high-temperature magnetocaloric materials to designing functional, tunable devices that are actually ready for application in a refrigerator setup.

Lev: From an engineering standpoint, it suggests that powder metallurgy is a viable way to produce these complex layered structures with the necessary density and heat transfer properties.

Kai: So, it’s about taking fundamental material science and translating it into a tangible magnetic cooling component that can be built.

More episodes

← Home