Developing the Field Selector System for the SHARP Multi-IFU: Optomechanical Design and First Prototype Validation
summary
The gist
The paper presents an innovative Field Selector System (FSS) developed for VESPER, the multi-Integral Field Unit of the SHARP near-infrared spectrograph This system employs an array of movable…
In short
A Field Selector System (FSS) was developed for VESPER, a multi-Integral Field Unit in SHARP. The system uses six movable probes that scan the focal plane to select targets. Novel opto-mechanical synchronization links probe movement ($\Delta y$) to mirror shifts ($\Delta y/2$), maintaining a constant optical path length across multiple probes simultaneously.
Key concepts
- Field Selector System (FSS)
- A mechanism designed to collect light from multiple targets in the focal plane and direct it efficiently to an image slicer. It uses six movable probes that scan the area, allowing the system to select specific targets rather than dividing the whole focal plane into fixed channels.
- Opto-mechanical Synchronization
- The core innovation where moving a probe by a distance ($\Delta y$) triggers a corresponding shift in folding mirrors by half that distance ($\Delta y/2$). This precise linkage ensures that even as probes move independently to select targets, they share the same optical path length, forming a continuous image.
- Image Slicer
- A component used in the system to divide the collected light image into smaller, manageable slices. The FSS is designed so that multiple probes can feed light onto this slicer, making it easy to select and process different spatial regions of the sky.
- Local Tilt Error
- An unwanted rotational deviation observed in the probe and mirror assembly caused by mechanical clearance or imperfections in the rail system. This tilt was measured at approximately $\pm 0.061^{\circ}$ during scanning, indicating a key area for mechanical design improvement.
Terminology used across episodes
This episode discusses
- Developing the Field Selector System for the SHARP Multi-IFU: Optomechanical Design and First Prototype Validation · Paper Radio
The paper
Developing the Field Selector System for the SHARP Multi-IFU: Optomechanical Design and First Prototype Validation · Read on arXiv
H. Mahmoodzadeh, P. Saracco, I. Di Antonio, P. Conconi, D. Scaccabrozzi, B. Saggin, E. Molinari, C. Arcidiacono, E. Cascone, V. Cianniello, F. D’ALESSIO, V. De Caprio, G. Di Rico3, B. Di Francesco3, C. Eredia6, P. Franzetti8, Üm Fumaná8
INAF - Osservatorio Astronomico di Brera · Politecnico di Milano Department of Mechanical Engineering · INAF - Osservatorio Astronomico d’Abruzzo · Università degli Studi di Padova Department of Industrial Engineering Padova Italy · INAF - Osservatorio Astronomico di Padova · INAF - Osservatorio Astronomico di Capodimonte · INAF - Osservatorio Astronomico di Roma · INAF - IASF
DOI: 10.1364/AO.612081
Transcript
Introduction to the show: ident: Astrophysics. The day in astrophysics: observations, models and what the data forces.
Vera: We're looking at the paper: "Developing the Field Selector System for the SHARP Multi-IFU".
Jocelyn: Here's the gist of the paper. The paper presents an innovative Field Selector System (FSS) developed for VESPER, the multi-Integral Field Unit of the SHARP near-infrared spectrograph This system employs an array of movable light-collection probes that travel along parallel, vertically offset planes to avoid mechanical interference and vignetting The true novelty lies in its opto-mechanical synchronization: as each probe translates by Δy to select a target, a set of folding mirrors shifts by Δy/2 This maintains a constant optical path length, allowing multiple independently moving probes to share a single focal plane and form a continuous image on it, easy to slice by the slicer System Architecture and Novelty The Field Selector System (FSS) is designed to simultaneously collect light from multiple targets in the ELT focal plane and direct it to an image slicer The system utilizes six movable light-collection probes associated with each VESPER channel that scan the focal plane to select the required target positions Unlike fixed field-splitting systems such as MUSE, the SHARP FSS does not simultaneously divide the complete focal plane into a fixed set of channels and target selection is achieved through macroscopic movable optical elements rather than individually addressable focal-plane apertures The structure involves six probes feeding one module of VESPER, covering half of the total area (∼10”×40”) Mechanical Design and Synchronization The optical design of the field selector system (FSS) feeding one VESPER channel consists of six probes arranged along parallel planes, alternately offset up and down by about 24 mm The movement of these folding mirrors is driven by a ball screw mechanism, where the same stepper motor that drives the collecting prism is utilized to move the folding mirrors with a gear ratio of 0.5 The mechanical design employs an array of 12 prisms distributed over two parallel planes for target selection and light management within the optical system The main structural box is composed of aluminum alloy plates selected for their favorable strength per weight ratio, machinability, and thermal performance at cryogenic temperatures Prototype Validation and Error Analysis The prototype validation involved testing a system representing one quarter of the final assembly to evaluate performance and identify potential areas for improvement Two main sources of error were identified during the experimental tests: 1.
Vera: A local tilt of the probe and folding mirrors assembly caused by mechanical clearance present in the movable mount and rail system 2.
Jocelyn: A position-dependent tilt resulting from imperfections in the straightness of the rail system, which vary as the probe moves across the scan range Performance Metrics and Future Directions The analysis of measured displacements and equivalent angular deviations showed that a significant local tilt in the x-direction (Δx) was observed, primarily attributed to mechanical clearance in the movable parts and rail system The maximum measured displacement fluctuates within approximately ±0.16 mm, corresponding to an equivalent angular deviation (tilting of folding mirrors) of ±0.061° during the forward scan Further improvement is expected by using higher-precision rectangular linear guides and increased separation between the rails in the y-direction The results provide a solid foundation for the next development phase, which will focus on implementing proposed design improvements and performing cryogenic validation tests The future work will focus on implementing the proposed design improvements, performing cryogenic validation tests, and evaluating the system under operational conditions representative of the final instrument.
Vera: The results demonstrate good repeatability of the scanning mechanism and provide valuable insight into the relationship between mechanical tolerances and optical performance The analysis identified several opportunities for improvement, including the use of higher-precision linear guides, increased rail separation, improved probe support, optimized lead-screw force transmission, and alignment-based assembly procedures These modifications are expected to significantly reduce positioning and tilting errors and enhance system stability.
Title and authors: Vera: The authors are Mahmoodzadeh, Saracco, Conconi and their team, and the title says they're developing an optomechanical design and then validating a first prototype. It’s about solving the problem of how to get light from multiple targets into an image slicer efficiently.
Jocelyn: I see it focusing on the system design itself, which means they aren't just looking at the final telescope setup, but really how the components interact optically and mechanically to do that selection.
The paper's summary: Vera: The core idea they present is a new probe-based approach for field selection and light collection. Instead of fixed splitting, they are using an array of movable light-collection probes that travel along parallel planes to scan the focal plane.
Jocelyn: So, it sounds like instead of having all those channels fixed in place, you move something—these probes—to pick what you want to look at. And they’re using six movable probes associated with each VESPER channel covering about half the total area, around ten by forty arcseconds <ref:2611.06332#pg1>.
The paper's improvements: Vera: They detail some mechanical design improvements they found during their prototype validation, which is where they talk about how the system could be better. They identified a few error sources that they wanted to fix, like local tilts in both the x-direction and z-direction.
Jocelyn: And for those errors, the suggested fixes involve using higher precision rectangular linear guides with increased separation between the rails in the y-direction to reduce rotational motion susceptibility.
Conclusion: Vera: So, they conclude that their prototype shows good repeatability in the scanning mechanism, but they also found that mechanical tolerances cause significant local tilts, especially in the x-direction. They pointed out opportunities for improvement like using higher precision linear guides and better probe support.
Jocelyn: And even though they tested this at ambient temperature with commercial components, they set a solid foundation for the next phase, which is to perform cryogenic validation tests under operational conditions representative of the final instrument.
Subrahmanyan: From a theoretical standpoint, the results give us insight into how mechanical tolerances directly translate into angular deviations in the optical performance. The fact that they found an equivalent angular deviation of zero point sixty-one degrees during the forward scan is a concrete number to work with when modeling system errors.
Vera: Exactly, Subrahmanyan. It shows that even small mechanical clearances in the movable mount can cause real tilting of the folding mirrors, and those tilts depend on where you are in the scan range.
Jocelyn: And it tells us that for this kind of multi-IFU setup, if you want to move beyond just fixing components, you need to think about aligning them during assembly rather than relying only on manufacturing accuracy.
Subrahmanyan: That alignment-based approach sounds like a necessary step for achieving the angular resolution they're aiming for, especially given the thirty milliarcsecond angular resolution requirement mentioned in Table two of the paper <ref:2611.06332#pg1>.
Vera: Right, so even though they are using commercial components now, they have to plan for differential thermal contraction later when they move to cryogenic operation, because that’s going to introduce new mechanical behaviors.
Jocelyn: That's right. So we've looked at the design concepts and seen how the first prototype performs mechanically before we talk about what these results mean for the final instrument on Earth.
More episodes
- 2607.17929-gevolution 2.0: GPU-accelerated relativistic N-body simulations for cosmology
- The day in conversation for 2026-11-19
- Daily Summary for 2026-11-19
- 2509.02657-On the synergetic use of Ariel and JWST for exoplanet atmospheric science
- 2609.10042-Modelling Fourier filtering wavefront sensors for PSD-based methods: the AOPERA tool
- 2511.05639-Performance of the AstroPix Prototype Module for the Barrel Imaging Calorimeter at the ePIC Detector and in Space-Based Payloads
- 2610.19909-RPCA: a Resolved PSF reconstruction method for undersampled images
- 2512.03440-An Analysis of LIGO Glitches Using t-SNE During the First Part of the Fourth LIGO-Virgo-KAGRA Observing Run
- 2608.10284-Lunar Reflective Interferometry
- 2610.16633-Institutional broadening of the Japanese astronomy and astrophysics research community during 1996-2025